android_kernel_motorola_sm6225/drivers/net/eexpress.h

180 lines
4.7 KiB
C
Raw Normal View History

/*
* eexpress.h: Intel EtherExpress16 defines
*/
/*
* EtherExpress card register addresses
* as offsets from the base IO region (dev->base_addr)
*/
#define DATAPORT 0x0000
#define WRITE_PTR 0x0002
#define READ_PTR 0x0004
#define SIGNAL_CA 0x0006
#define SET_IRQ 0x0007
#define SM_PTR 0x0008
#define MEM_Dec 0x000a
#define MEM_Ctrl 0x000b
#define MEM_Page_Ctrl 0x000c
#define Config 0x000d
#define EEPROM_Ctrl 0x000e
#define ID_PORT 0x000f
#define MEM_ECtrl 0x000f
/*
* card register defines
*/
/* SET_IRQ */
#define SIRQ_en 0x08
#define SIRQ_dis 0x00
/* EEPROM_Ctrl */
#define EC_Clk 0x01
#define EC_CS 0x02
#define EC_Wr 0x04
#define EC_Rd 0x08
#define ASIC_RST 0x40
#define i586_RST 0x80
#define eeprom_delay() { udelay(40); }
/*
* i82586 Memory Configuration
*/
/* (System Configuration Pointer) System start up block, read after 586_RST */
#define SCP_START 0xfff6
/* Intermediate System Configuration Pointer */
#define ISCP_START 0x0000
/* System Command Block */
#define SCB_START 0x0008
/* Start of buffer region. Everything before this is used for control
* structures and the CU configuration program. The memory layout is
* determined in eexp_hw_probe(), once we know how much memory is
* available on the card.
*/
#define TX_BUF_START 0x0100
#define TX_BUF_SIZE ((24+ETH_FRAME_LEN+31)&~0x1f)
#define RX_BUF_SIZE ((32+ETH_FRAME_LEN+31)&~0x1f)
/*
* SCB defines
*/
/* these functions take the SCB status word and test the relevant status bit */
#define SCB_complete(s) ((s&0x8000)!=0)
#define SCB_rxdframe(s) ((s&0x4000)!=0)
#define SCB_CUdead(s) ((s&0x2000)!=0)
#define SCB_RUdead(s) ((s&0x1000)!=0)
#define SCB_ack(s) (s & 0xf000)
/* Command unit status: 0=idle, 1=suspended, 2=active */
#define SCB_CUstat(s) ((s&0x0300)>>8)
/* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */
#define SCB_RUstat(s) ((s&0x0070)>>4)
/* SCB commands */
#define SCB_CUnop 0x0000
#define SCB_CUstart 0x0100
#define SCB_CUresume 0x0200
#define SCB_CUsuspend 0x0300
#define SCB_CUabort 0x0400
#define SCB_resetchip 0x0080
#define SCB_RUnop 0x0000
#define SCB_RUstart 0x0010
#define SCB_RUresume 0x0020
#define SCB_RUsuspend 0x0030
#define SCB_RUabort 0x0040
/*
* Command block defines
*/
#define Stat_Done(s) ((s&0x8000)!=0)
#define Stat_Busy(s) ((s&0x4000)!=0)
#define Stat_OK(s) ((s&0x2000)!=0)
#define Stat_Abort(s) ((s&0x1000)!=0)
#define Stat_STFail ((s&0x0800)!=0)
#define Stat_TNoCar(s) ((s&0x0400)!=0)
#define Stat_TNoCTS(s) ((s&0x0200)!=0)
#define Stat_TNoDMA(s) ((s&0x0100)!=0)
#define Stat_TDefer(s) ((s&0x0080)!=0)
#define Stat_TColl(s) ((s&0x0040)!=0)
#define Stat_TXColl(s) ((s&0x0020)!=0)
#define Stat_NoColl(s) (s&0x000f)
/* Cmd_END will end AFTER the command if this is the first
* command block after an SCB_CUstart, but BEFORE the command
* for all subsequent commands. Best strategy is to place
* Cmd_INT on the last command in the sequence, followed by a
* dummy Cmd_Nop with Cmd_END after this.
*/
#define Cmd_END 0x8000
#define Cmd_SUS 0x4000
#define Cmd_INT 0x2000
#define Cmd_Nop 0x0000
#define Cmd_SetAddr 0x0001
#define Cmd_Config 0x0002
#define Cmd_MCast 0x0003
#define Cmd_Xmit 0x0004
#define Cmd_TDR 0x0005
#define Cmd_Dump 0x0006
#define Cmd_Diag 0x0007
/*
* Frame Descriptor (Receive block) defines
*/
#define FD_Done(s) ((s&0x8000)!=0)
#define FD_Busy(s) ((s&0x4000)!=0)
#define FD_OK(s) ((s&0x2000)!=0)
#define FD_CRC(s) ((s&0x0800)!=0)
#define FD_Align(s) ((s&0x0400)!=0)
#define FD_Resrc(s) ((s&0x0200)!=0)
#define FD_DMA(s) ((s&0x0100)!=0)
#define FD_Short(s) ((s&0x0080)!=0)
#define FD_NoEOF(s) ((s&0x0040)!=0)
struct rfd_header {
volatile unsigned long flags;
volatile unsigned short link;
volatile unsigned short rbd_offset;
volatile unsigned short dstaddr1;
volatile unsigned short dstaddr2;
volatile unsigned short dstaddr3;
volatile unsigned short srcaddr1;
volatile unsigned short srcaddr2;
volatile unsigned short srcaddr3;
volatile unsigned short length;
/* This is actually a Receive Buffer Descriptor. The way we
* arrange memory means that an RBD always follows the RFD that
* points to it, so they might as well be in the same structure.
*/
volatile unsigned short actual_count;
volatile unsigned short next_rbd;
volatile unsigned short buf_addr1;
volatile unsigned short buf_addr2;
volatile unsigned short size;
};
/* Returned data from the Time Domain Reflectometer */
#define TDR_LINKOK (1<<15)
#define TDR_XCVRPROBLEM (1<<14)
#define TDR_OPEN (1<<13)
#define TDR_SHORT (1<<12)
#define TDR_TIME 0x7ff