53 lines
1.7 KiB
Text
53 lines
1.7 KiB
Text
|
OPL3-SA1 sound driver (opl3sa.o)
|
||
|
|
|
||
|
|
---
|
||
|
|
Note: This howto only describes how to setup the OPL3-SA1 chip; this info
|
||
|
|
does not apply to the SA2, SA3, or SA4.
|
||
|
|
---
|
||
|
|
|
||
|
|
The Yamaha OPL3-SA1 sound chip is usually found built into motherboards, and
|
||
|
|
it's a decent little chip offering a WSS mode, a SB Pro emulation mode, MPU401
|
||
|
|
and OPL3 FM Synth capabilities.
|
||
|
|
|
||
|
|
You can enable inclusion of the driver via CONFIG_SOUND_OPL3SA1=m, or
|
||
|
|
CONFIG_SOUND_OPL3SA1=y through 'make config/xconfig/menuconfig'.
|
||
|
|
|
||
|
|
You'll need to know all of the relevant info (irq, dma, and io port) for the
|
||
|
|
chip's WSS mode, since that is the mode the kernel sound driver uses, and of
|
||
|
|
course you'll also need to know about where the MPU401 and OPL3 ports and
|
||
|
|
IRQs are if you want to use those.
|
||
|
|
|
||
|
|
Here's the skinny on how to load it as a module:
|
||
|
|
|
||
|
|
modprobe opl3sa io=0x530 irq=11 dma=0 dma2=1 mpu_io=0x330 mpu_irq=5
|
||
|
|
|
||
|
|
Module options in detail:
|
||
|
|
|
||
|
|
io: This is the WSS's port base.
|
||
|
|
irq: This is the WSS's IRQ.
|
||
|
|
dma: This is the WSS's DMA line. In my BIOS setup screen this was
|
||
|
|
listed as "WSS Play DMA"
|
||
|
|
dma2: This is the WSS's secondary DMA line. My BIOS calls it the
|
||
|
|
"WSS capture DMA"
|
||
|
|
|
||
|
|
mpu_io: This is the MPU401's port base.
|
||
|
|
mpu_irq: This is the MPU401's IRQ.
|
||
|
|
|
||
|
|
If you'd like to use the OPL3 FM Synthesizer, make sure you enable
|
||
|
|
CONFIG_SOUND_YM3812 (in 'make config'). That'll build the opl3.o module.
|
||
|
|
|
||
|
|
Then a simple 'insmod opl3 io=0x388', and you now have FM Synth.
|
||
|
|
|
||
|
|
You can also use the SoftOSS software synthesizer instead of the builtin OPL3.
|
||
|
|
Here's how:
|
||
|
|
|
||
|
|
Say 'y' or 'm' to "SoftOSS software wave table engine" in make config.
|
||
|
|
|
||
|
|
If you said yes, the software synth is available once you boot your new
|
||
|
|
kernel.
|
||
|
|
|
||
|
|
If you chose to build it as a module, just insmod the resulting softoss2.o
|
||
|
|
|
||
|
|
Questions? Comments?
|
||
|
|
<stiker@northlink.com>
|