[ Upstream commit bed0adac1ded4cb486ba19a3a7e730fbd9a1c9c6 ]
The wcnss_get_irq function is expected to return a value > 0 in the
event that an IRQ is succssfully obtained, but it instead returns 0.
This causes the stop and ready IRQs to never actually be used despite
being defined in the device-tree. This patch fixes that.
Fixes: aed361adca ("remoteproc: qcom: Introduce WCNSS peripheral image loader")
Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220526141740.15834-2-sireeshkodali1@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f90161a66bc3d6b9fe8dde4d9028d20eae1b62a ]
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: aed361adca ("remoteproc: qcom: Introduce WCNSS peripheral image loader")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220308063102.10049-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e013f455d95add874f310dc47c608e8c70692ae5 upstream
The following mem abort is observed when the mba firmware size exceeds
the allocated mba region. MBA firmware size is restricted to a maximum
size of 1M and remaining memory region is used by modem debug policy
firmware when available. Hence verify whether the MBA firmware size lies
within the allocated memory region and is not greater than 1M before
loading.
Err Logs:
Unable to handle kernel paging request at virtual address
Mem abort info:
...
Call trace:
__memcpy+0x110/0x180
rproc_start+0x40/0x218
rproc_boot+0x5b4/0x608
state_store+0x54/0xf8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
kernfs_fop_write+0x140/0x230
vfs_write+0xc4/0x208
ksys_write+0x74/0xf8
__arm64_sys_write+0x24/0x30
...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sudip: manual backport to old file path]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 135b9e8d1cd8ba5ac9ad9bcf24b464b7b052e5b8 upstream
The following mem abort is observed when one of the modem blob firmware
size exceeds the allocated mpss region. Fix this by restricting the copy
size to segment size using request_firmware_into_buf before load.
Err Logs:
Unable to handle kernel paging request at virtual address
Mem abort info:
...
Call trace:
__memcpy+0x110/0x180
rproc_start+0xd0/0x190
rproc_boot+0x404/0x550
state_store+0x54/0xf8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
kernfs_fop_write+0x140/0x230
vfs_write+0xc4/0x208
ksys_write+0x74/0xf8
...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sudip: manual backport to old file path]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b7be880074c73540948f8fc597e0407b98fabfa upstream.
Sometimes the stop triggers a watchdog rather than a stop-ack. Update
the running state to false on requesting stop to skip the watchdog
instead.
Error Logs:
$ echo stop > /sys/class/remoteproc/remoteproc0/state
ipa 1e40000.ipa: received modem stopping event
remoteproc-modem: watchdog received: sys_m_smsm_mpss.c:291:APPS force stop
qcom-q6v5-mss 4080000.remoteproc-modem: port failed halt
ipa 1e40000.ipa: received modem offline event
remoteproc0: stopped remote processor 4080000.remoteproc-modem
Reviewed-by: Evan Green <evgreen@chromium.org>
Fixes: 3b415c8fb2 ("remoteproc: q6v5: Extract common resource handling")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200602163257.26978-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6442df49400b466431979e7634849a464a5f1861 ]
If ida_simple_get() returns an error when called in rproc_alloc(),
put_device() is called to clean things up. By this time the rproc
device type has been assigned, with rproc_type_release() as the
release function.
The first thing rproc_type_release() does is call:
idr_destroy(&rproc->notifyids);
But at the time the ida_simple_get() call is made, the notifyids
field in the remoteproc structure has not been initialized.
I'm not actually sure this case causes an observable problem, but
it's incorrect. Fix this by initializing the notifyids field before
calling ida_simple_get() in rproc_alloc().
Fixes: b5ab5e24e9 ("remoteproc: maintain a generic child device for each rproc")
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 00a0eec59ddbb1ce966b19097d8a8d2f777e726a upstream.
Index of rvring is computed using pointer arithmetic. However, since
rvring->rvdev->vring is the base of the vring array, computation
of rvring idx should be reversed. It previously lead to writing at negative
indices in the resource table.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20191004073736.8327-1-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 80ec419c3404106c563aaf56aa6b516a59c4cdfb ]
Proxy vote for QDSS clock and remove vote on handover interrupt
to provide MSS PBL with access to STM hardware registers during
boot. Add "snoc_axi" and "mnoc_axi" to the active clock list.
Rename "gpll0_mss_clk" to "gpll0_mss" for consistency across SoCs.
Fixes: 9f058fa2ef ("remoteproc: qcom: Add support for mss remoteproc on msm8996")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3ae96c0e6b042a883927493351b2af6ee05e92c ]
Currently with GLINK_SSR enabled each fatal crash results in servicing
a crash from wdog as well. This is due to a race that occurs in setting
the running flag in the shutdown path. Fix this by moving the running
flag to the end of fatal interrupt handler.
Crash Logs:
qcom-q6v5-pil 4080000.remoteproc: fatal error without message
remoteproc remoteproc0: crash detected in 4080000.remoteproc: type fatal
error
remoteproc remoteproc0: handling crash #1 in 4080000.remoteproc
remoteproc remoteproc0: recovering 4080000.remoteproc
qcom-q6v5-pil 4080000.remoteproc: watchdog without message
remoteproc remoteproc0: crash detected in 4080000.remoteproc: type watchdog
remoteproc:glink-edge: intent request timed out
qcom_glink_ssr remoteproc:glink-edge.glink_ssr.-1.-1: failed to send
cleanup message
qcom_glink_ssr remoteproc:glink-edge.glink_ssr.-1.-1: timeout waiting
for cleanup done message
qcom-q6v5-pil 4080000.remoteproc: timed out on wait
qcom-q6v5-pil 4080000.remoteproc: port failed halt
remoteproc remoteproc0: stopped remote processor 4080000.remoteproc
qcom-q6v5-pil 4080000.remoteproc: MBA booted, loading mpss
remoteproc remoteproc0: remote processor 4080000.remoteproc is now up
remoteproc remoteproc0: handling crash #2 in 4080000.remoteproc
remoteproc remoteproc0: recovering 4080000.remoteproc
qcom-q6v5-pil 4080000.remoteproc: port failed halt
remoteproc remoteproc0: stopped remote processor 4080000.remoteproc
qcom-q6v5-pil 4080000.remoteproc: MBA booted, loading mpss
remoteproc remoteproc0: remote processor 4080000.remoteproc is now up
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faeadbb64094757150a8c2a3175ca418dbdd472c ]
The remoteproc framework provides a sysfs file 'firmware'
for modifying the firmware image name from userspace. Add
an additional check to ensure NULL firmwares are errored
out right away, rather than getting a delayed error while
requesting a firmware during the start of a remoteproc
later on.
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e28dbbeced6152b9ea7c417ff8cef3f7dcf0f19 ]
da8xx_rproc_mem size is of type size_t, so use %zx to format the debug
print of it to avoid a compile warning.
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbcda30271752bb7490f2e2aef5411dbcae69116 ]
The memory ownership transfer request is performed using SCM, ensure
that SCM is available before we probe the driver if memory protection is
needed by the subsystem.
Fixes: 6c5a9dc248 ("remoteproc: qcom: Make secure world call for mem ownership switch")
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <briannorris@chromium.org>
[bjorn: Added condition for need_mem_protection, updated commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e2517d126171a41f801738ffd19687836cd178a ]
Commit d5269c4553a6 ("remoteproc: qcom: q6v5: Propagate EPROBE_DEFER")
fixed up our probe code to handle -EPROBE_DEFER, but it ignored one of
our interrupts, and it also didn't really handle all the other error
codes you might get (e.g., with a bad DT definition). Handle those all
explicitly.
Fixes: d5269c4553a6 ("remoteproc: qcom: q6v5: Propagate EPROBE_DEFER")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d5269c4553a64b6882f2c019ae21b783a0984a83 upstream.
In the case that the interrupts fail to result because of the
interrupt-controller not yet being registered the
platform_get_irq_byname() call will fail with -EPROBE_DEFER, but passing
this into devm_request_threaded_irq() will result in -EINVAL being
returned, the driver is therefor not reprobed later.
Fixes: 3b415c8fb2 ("remoteproc: q6v5: Extract common resource handling")
Cc: stable@vger.kernel.org
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to using the reset framework instead of handcoded reset routines
we used so far.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Davinci remoteproc driver does not support error recovery at
present, so mark the corresponding remoteproc flag appropriately
so that the debugfs flag shows the value as 'disabled' by default.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The format specifier "%p" can leak kernel addresses.
Use "%pK" instead.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The format specifier "%p" can leak kernel addresses.
Use "%pK" instead.
This patch proposes changes for remoteproc core only.
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A new driver got added that depends on QCOM_SMD and fails to link
as built-in with CONFIG_QCOM_SMD=m:
drivers/remoteproc/qcom_common.o: In function `smd_subdev_stop':
qcom_common.c:(.text+0x674): undefined reference to `qcom_smd_unregister_edge'
drivers/remoteproc/qcom_common.o: In function `smd_subdev_start':
qcom_common.c:(.text+0x700): undefined reference to `qcom_smd_register_edge'
We've fixed the same thing several times before, so use the same
dependency here.
Fixes: 3a3d4163e0 ("remoteproc: qcom: Introduce Hexagon V5 based WCSS driver")
Acked-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Unwind the modified table_ptr and restore it to the local copy
upon any subsequent failures in the rproc_start() function. This
keeps the function to remain balanced on failures without the need
to balance any modified variables elsewhere.
While at this, do some minor cleanup of the extra lines between
the failure labels as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
[bjorn: unconditionally set table_ptr to cached_table]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
GCC_MSS_AXIS2 clock is used for disabling boot IMEM (a part of
AP boot up). With Boot IMEM disable now a part TZ/ATF, AXIS2
clock is no longer required post AP boot up and expected to
remain untouched. However if the clock is turned ON after Q6
is brought out of reset and later turned off, it results in
modem hang. When Q6 attempts a power collapse the internal
handshaking to check if AXIS2 is idle never goes through since
it is turned off preventing the RSC from getting triggered,
leaving modem in a funky state. Hence removing AXIS2 clk
enable/disable from the driver.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The new driver only works as built-in code at the moment but fails
with a link error when configured as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/remoteproc/qcom_q6v5.o
see include/linux/module.h for more information
ERROR: "qcom_q6v5_init" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_wait_for_start" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_prepare" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_unprepare" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_request_stop" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_init" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_q6v5_wait_for_start" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_q6v5_prepare" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_q6v5_unprepare" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_q6v5_request_stop" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
This exports the internal symbols as needed and adds the MODULE_LICENSE()
and MODULE_DESCRIPTION() tags. I could not figure out the author, so I
did not add a MODULE_AUTHOR() tag for now.
Fixes: 3b415c8fb2 ("remoteproc: q6v5: Extract common resource handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On rare occasions a subdevice might need to prepare some hardware
resources before a remote processor is booted, and clean up some
state after it has been shut down.
One such example is the IP Accelerator found in various Qualcomm
platforms, which is accessed directly from both the modem remoteproc
and the application subsystem and requires an intricate lockstep
process when bringing the modem up and down.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[elder@linaro.org: minor description and comment edits]
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rename functions used when subdevices are started and stopped to
reflect the new naming scheme.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In preparation of adding the additional prepare and unprepare operations
make the client responsible for filling out the function pointers of the
rproc_subdev. This makes the arguments to rproc_add_subdev() more
manageable, in particular when some of the functions are left out.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[elder@linaro.org: added comment about assigning function pointers]
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some subdevices, such as glink ssr only care about the stop operation,
so make the operations optional to reduce client code.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
"start" and "stop" are more suitable names for how these two operations
are used, and they fit better with the upcoming introduction of two
additional operations in the struct.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[elder@linaro.org: minor comment edits]
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
IPQ8074 has an integrated Hexagon dsp core q6v5 and a wireless lan
(Lithium) IP. An mdt type single image format is used for the
firmware. So the mdt_load function can be directly used to load
the firmware. Also add the relevant resets required for this core.
Acked-by: Rob Herring <robh@kernel.org> (bindings)
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
[bjorn: Rewrote as a separate driver, intead of extending q6v5_pil.c]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Migrate the MSS remoteproc driver to use the newly extracted helper
functions.
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Migrate the Hexagon V5 PAS (ADSP) driver to using the newly extracted
helper functions. The use of the handover callback does introduce latent
disabling of proxy resources. But apart from this there should be no
change in functionality.
Reviewed-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Shared between all Hexagon V5 based remoteprocs is the handling of the 5
interrupts and the SMP2P stop request, so break this out into a separate
function in order to allow these drivers to be cleaned up.
Reviewed-by: Rohit kumar <rohitkr@codeaurora.org>
Tested-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With PHYS_ADDR_MAX there is now a type safe variant for all bits set.
Make use of it.
Patch created using a semantic patch as follows:
// <smpl>
@@
typedef phys_addr_t;
@@
-(phys_addr_t)ULLONG_MAX
+PHYS_ADDR_MAX
// </smpl>
Link: http://lkml.kernel.org/r/20180419214204.19322-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add GLINK subdevice to allow definition of GLINK edge as a
child of modem-pil.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
From SDM845, the Q6SS reset sequence on software side has been
simplified with the introduction of boot FSM which assists in
bringing the Q6 out of reset.
SDM845 brings a new reset signal ALT_RESET which is a part of
the MSS subsystem hence requires reset clks to be enabled before
assert/deassert. Use the SoC specific reset helper function to
add support for ALT_RESET in SDM845.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Adding reset assert/deassert helper functions to handle SoC
specific reset sequences. This wil be used by SDM845 to assert and
deassert ALT_RESET and MSS_RESET signals.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce interrupt handler for smp2p ready interrupt to
handle start completion. Move the proxy votes for clocks
and regulators to the handover interrupt context.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
[bjorn: Only proxy unvote if handover irq has not fired]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
q6v5_request_irq() was supposed to return the irq number, but ret is
overwritten by the request_irq(), fix this and return the IRQ on
success.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Checkpatch recommends to use octal perms instead of S_IRUGO.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We're currently switching the platform to using the common clock
framework. We need to explicitly prepare and unprepare the rproc
clock.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The davinci platform is being switched to using the common clock
framework, where clk_enable() can fail. Add the return value check.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add missing of_node_put()s at two places for device nodes returned by
of_parse_phandle().
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating
Hexagon v5")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix rproc_add_subdev parameter name and inverse the crashed logic.
Fixes: 880f5b3882 ("remoteproc: Pass type of shutdown to subdev remove")
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Any failure in the secure call for transferring mem ownership of mba
region to Q6 would result in reporting that the remoteproc device
is running. This is because the previous q6v5_clk_enable would have
been a success. Prevent this by updating variable 'ret' accordingly.
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently calling list_del on smd subdev remove path results in
null pointer dereference on glink only platforms. Fix this by
adding safety checks in glink/smd subdev remove paths.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Access to the socket API and the root network namespace is only available
when networking is enabled:
ERROR: "kernel_sendmsg" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "sock_release" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "sock_create_kern" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "kernel_getsockname" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "init_net" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "kernel_recvmsg" [drivers/soc/qcom/qmi_helpers.ko] undefined!
Adding a dependency on CONFIG_NET lets us build it in all randconfig
builds.
Fixes: 9b8a11e826 ("soc: qcom: Introduce QMI encoder/decoder")
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We can return directly at the beginning of the function and save the 'err'
label.
We can also explicitly return 0 when the probe succeed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
