[ Upstream commit 6ca3c005d0604e8d2b439366e3923ea58db99641 ]
According to the synchronization rules for .ndo_get_stats() as seen in
Documentation/networking/netdevices.rst, acquiring a plain spin_lock()
should not be illegal, but the bridge driver implementation makes it so.
After running these commands, I am being faced with the following
lockdep splat:
$ ip link add link swp0 name macsec0 type macsec encrypt on && ip link set swp0 up
$ ip link add dev br0 type bridge vlan_filtering 1 && ip link set br0 up
$ ip link set macsec0 master br0 && ip link set macsec0 up
========================================================
WARNING: possible irq lock inversion dependency detected
6.4.0-04295-g31b577b4bd4a #603 Not tainted
--------------------------------------------------------
swapper/1/0 just changed the state of lock:
ffff6bd348724cd8 (&br->lock){+.-.}-{3:3}, at: br_forward_delay_timer_expired+0x34/0x198
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&ocelot->stats_lock){+.+.}-{3:3}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Chain exists of:
&br->lock --> &br->hash_lock --> &ocelot->stats_lock
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ocelot->stats_lock);
local_irq_disable();
lock(&br->lock);
lock(&br->hash_lock);
<Interrupt>
lock(&br->lock);
*** DEADLOCK ***
(details about the 3 locks skipped)
swp0 is instantiated by drivers/net/dsa/ocelot/felix.c, and this
only matters to the extent that its .ndo_get_stats64() method calls
spin_lock(&ocelot->stats_lock).
Documentation/locking/lockdep-design.rst says:
| A lock is irq-safe means it was ever used in an irq context, while a lock
| is irq-unsafe means it was ever acquired with irq enabled.
(...)
| Furthermore, the following usage based lock dependencies are not allowed
| between any two lock-classes::
|
| <hardirq-safe> -> <hardirq-unsafe>
| <softirq-safe> -> <softirq-unsafe>
Lockdep marks br->hash_lock as softirq-safe, because it is sometimes
taken in softirq context (for example br_fdb_update() which runs in
NET_RX softirq), and when it's not in softirq context it blocks softirqs
by using spin_lock_bh().
Lockdep marks ocelot->stats_lock as softirq-unsafe, because it never
blocks softirqs from running, and it is never taken from softirq
context. So it can always be interrupted by softirqs.
There is a call path through which a function that holds br->hash_lock:
fdb_add_hw_addr() will call a function that acquires ocelot->stats_lock:
ocelot_port_get_stats64(). This can be seen below:
ocelot_port_get_stats64+0x3c/0x1e0
felix_get_stats64+0x20/0x38
dsa_slave_get_stats64+0x3c/0x60
dev_get_stats+0x74/0x2c8
rtnl_fill_stats+0x4c/0x150
rtnl_fill_ifinfo+0x5cc/0x7b8
rtmsg_ifinfo_build_skb+0xe4/0x150
rtmsg_ifinfo+0x5c/0xb0
__dev_notify_flags+0x58/0x200
__dev_set_promiscuity+0xa0/0x1f8
dev_set_promiscuity+0x30/0x70
macsec_dev_change_rx_flags+0x68/0x88
__dev_set_promiscuity+0x1a8/0x1f8
__dev_set_rx_mode+0x74/0xa8
dev_uc_add+0x74/0xa0
fdb_add_hw_addr+0x68/0xd8
fdb_add_local+0xc4/0x110
br_fdb_add_local+0x54/0x88
br_add_if+0x338/0x4a0
br_add_slave+0x20/0x38
do_setlink+0x3a4/0xcb8
rtnl_newlink+0x758/0x9d0
rtnetlink_rcv_msg+0x2f0/0x550
netlink_rcv_skb+0x128/0x148
rtnetlink_rcv+0x24/0x38
the plain English explanation for it is:
The macsec0 bridge port is created without p->flags & BR_PROMISC,
because it is what br_manage_promisc() decides for a VLAN filtering
bridge with a single auto port.
As part of the br_add_if() procedure, br_fdb_add_local() is called for
the MAC address of the device, and this results in a call to
dev_uc_add() for macsec0 while the softirq-safe br->hash_lock is taken.
Because macsec0 does not have IFF_UNICAST_FLT, dev_uc_add() ends up
calling __dev_set_promiscuity() for macsec0, which is propagated by its
implementation, macsec_dev_change_rx_flags(), to the lower device: swp0.
This triggers the call path:
dev_set_promiscuity(swp0)
-> rtmsg_ifinfo()
-> dev_get_stats()
-> ocelot_port_get_stats64()
with a calling context that lockdep doesn't like (br->hash_lock held).
Normally we don't see this, because even though many drivers that can be
bridge ports don't support IFF_UNICAST_FLT, we need a driver that
(a) doesn't support IFF_UNICAST_FLT, *and*
(b) it forwards the IFF_PROMISC flag to another driver, and
(c) *that* driver implements ndo_get_stats64() using a softirq-unsafe
spinlock.
Condition (b) is necessary because the first __dev_set_rx_mode() calls
__dev_set_promiscuity() with "bool notify=false", and thus, the
rtmsg_ifinfo() code path won't be entered.
The same criteria also hold true for DSA switches which don't report
IFF_UNICAST_FLT. When the DSA master uses a spin_lock() in its
ndo_get_stats64() method, the same lockdep splat can be seen.
I think the deadlock possibility is real, even though I didn't reproduce
it, and I'm thinking of the following situation to support that claim:
fdb_add_hw_addr() runs on a CPU A, in a context with softirqs locally
disabled and br->hash_lock held, and may end up attempting to acquire
ocelot->stats_lock.
In parallel, ocelot->stats_lock is currently held by a thread B (say,
ocelot_check_stats_work()), which is interrupted while holding it by a
softirq which attempts to lock br->hash_lock.
Thread B cannot make progress because br->hash_lock is held by A. Whereas
thread A cannot make progress because ocelot->stats_lock is held by B.
When taking the issue at face value, the bridge can avoid that problem
by simply making the ports promiscuous from a code path with a saner
calling context (br->hash_lock not held). A bridge port without
IFF_UNICAST_FLT is going to become promiscuous as soon as we call
dev_uc_add() on it (which we do unconditionally), so why not be
preemptive and make it promiscuous right from the beginning, so as to
not be taken by surprise.
With this, we've broken the links between code that holds br->hash_lock
or br->lock and code that calls into the ndo_change_rx_flags() or
ndo_get_stats64() ops of the bridge port.
Fixes: 2796d0c648 ("bridge: Automatically manage port promiscuous mode.")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62ce44c4fff947eebdf10bb582267e686e6835c9 ]
The bug fix was incomplete, it "replaced" crash with a memory leak.
The old code had an assignment to "ret" embedded into the conditional,
restore this.
Fixes: 7997eff82828 ("netfilter: ebtables: reject blobs that don't provide all entry points")
Reported-and-tested-by: syzbot+a24c5252f3e3ab733464@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d047283a7034140ea5da759a494fd2274affdd46 ]
The IPv6 path already drops dst in the daddr changed case, but the IPv4
path does not. This change makes the two code paths consistent.
Further, it is possible that there is already a metadata_dst allocated from
ingress that might already be attached to skbuff->dst while following
the bridge path. If it is not released before setting a new
metadata_dst, it will be leaked. This is similar to what is done in
bpf_set_tunnel_key() or ip6_route_input().
It is important to note that the memory being leaked is not the dst
being set in the bridge code, but rather memory allocated from some
other code path that is not being freed correctly before the skb dst is
overwritten.
An example of the leakage fixed by this commit found using kmemleak:
unreferenced object 0xffff888010112b00 (size 256):
comm "softirq", pid 0, jiffies 4294762496 (age 32.012s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 80 16 f1 83 ff ff ff ff ................
e1 4e f6 82 ff ff ff ff 00 00 00 00 00 00 00 00 .N..............
backtrace:
[<00000000d79567ea>] metadata_dst_alloc+0x1b/0xe0
[<00000000be113e13>] udp_tun_rx_dst+0x174/0x1f0
[<00000000a36848f4>] geneve_udp_encap_recv+0x350/0x7b0
[<00000000d4afb476>] udp_queue_rcv_one_skb+0x380/0x560
[<00000000ac064aea>] udp_unicast_rcv_skb+0x75/0x90
[<000000009a8ee8c5>] ip_protocol_deliver_rcu+0xd8/0x230
[<00000000ef4980bb>] ip_local_deliver_finish+0x7a/0xa0
[<00000000d7533c8c>] __netif_receive_skb_one_core+0x89/0xa0
[<00000000a879497d>] process_backlog+0x93/0x190
[<00000000e41ade9f>] __napi_poll+0x28/0x170
[<00000000b4c0906b>] net_rx_action+0x14f/0x2a0
[<00000000b20dd5d4>] __do_softirq+0xf4/0x305
[<000000003a7d7e15>] __irq_exit_rcu+0xc3/0x140
[<00000000968d39a2>] sysvec_apic_timer_interrupt+0x9e/0xc0
[<000000009e920794>] asm_sysvec_apic_timer_interrupt+0x16/0x20
[<000000008942add0>] native_safe_halt+0x13/0x20
Florian Westphal says: "Original code was likely fine because nothing
ever did set a skb->dst entry earlier than bridge in those days."
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Harsh Modi <harshmodi@google.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7997eff82828304b780dc0a39707e1946d6f1ebf ]
Harshit Mogalapalli says:
In ebt_do_table() function dereferencing 'private->hook_entry[hook]'
can lead to NULL pointer dereference. [..] Kernel panic:
general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
[..]
RIP: 0010:ebt_do_table+0x1dc/0x1ce0
Code: 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 5c 16 00 00 48 b8 00 00 00 00 00 fc ff df 49 8b 6c df 08 48 8d 7d 2c 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 88
[..]
Call Trace:
nf_hook_slow+0xb1/0x170
__br_forward+0x289/0x730
maybe_deliver+0x24b/0x380
br_flood+0xc6/0x390
br_dev_xmit+0xa2e/0x12c0
For some reason ebtables rejects blobs that provide entry points that are
not supported by the table, but what it should instead reject is the
opposite: blobs that DO NOT provide an entry point supported by the table.
t->valid_hooks is the bitmask of hooks (input, forward ...) that will see
packets. Providing an entry point that is not support is harmless
(never called/used), but the inverse isn't: it results in a crash
because the ebtables traverser doesn't expect a NULL blob for a location
its receiving packets for.
Instead of fixing all the individual checks, do what iptables is doing and
reject all blobs that differ from the expected hooks.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2577862eeb0be94f151f2f1fff662b028061b00 ]
When br_netfilter module is loaded, skbs may be diverted to the
ipv4/ipv6 hooks, just like as if we were routing.
Unfortunately, bridge filter hooks with priority 0 may be skipped
in this case.
Example:
1. an nftables bridge ruleset is loaded, with a prerouting
hook that has priority 0.
2. interface is added to the bridge.
3. no tcp packet is ever seen by the bridge prerouting hook.
4. flush the ruleset
5. load the bridge ruleset again.
6. tcp packets are processed as expected.
After 1) the only registered hook is the bridge prerouting hook, but its
not called yet because the bridge hasn't been brought up yet.
After 2), hook order is:
0 br_nf_pre_routing // br_netfilter internal hook
0 chain bridge f prerouting // nftables bridge ruleset
The packet is diverted to br_nf_pre_routing.
If call-iptables is off, the nftables bridge ruleset is called as expected.
But if its enabled, br_nf_hook_thresh() will skip it because it assumes
that all 0-priority hooks had been called previously in bridge context.
To avoid this, check for the br_nf_pre_routing hook itself, we need to
resume directly after it, even if this hook has a priority of 0.
Unfortunately, this still results in different packet flow.
With this fix, the eval order after in 3) is:
1. br_nf_pre_routing
2. ip(6)tables (if enabled)
3. nftables bridge
but after 5 its the much saner:
1. nftables bridge
2. br_nf_pre_routing
3. ip(6)tables (if enabled)
Unfortunately I don't see a solution here:
It would be possible to move br_nf_pre_routing to a higher priority
so that it will be called later in the pipeline, but this also impacts
ebtables evaluation order, and would still result in this very ordering
problem for all nftables-bridge hooks with the same priority as the
br_nf_pre_routing one.
Searching back through the git history I don't think this has
ever behaved in any other way, hence, no fixes-tag.
Reported-by: Radim Hrazdil <rhrazdil@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb3abdf2223cd0dfc07de85fe5a43ba7f435bdf ]
It is possible to stack bridges on top of each other. Consider the
following which makes use of an Ethernet switch:
br1
/ \
/ \
/ \
br0.11 wlan0
|
br0
/ | \
p1 p2 p3
br0 is offloaded to the switch. Above br0 is a vlan interface, for
vlan 11. This vlan interface is then a slave of br1. br1 also has a
wireless interface as a slave. This setup trunks wireless lan traffic
over the copper network inside a VLAN.
A frame received on p1 which is passed up to the bridge has the
skb->offload_fwd_mark flag set to true, indicating that the switch has
dealt with forwarding the frame out ports p2 and p3 as needed. This
flag instructs the software bridge it does not need to pass the frame
back down again. However, the flag is not getting reset when the frame
is passed upwards. As a result br1 sees the flag, wrongly interprets
it, and fails to forward the frame to wlan0.
When passing a frame upwards, clear the flag. This is the Rx
equivalent of br_switchdev_frame_unmark() in br_dev_xmit().
Fixes: f1c2eddf4c ("bridge: switchdev: Use an helper to clear forward mark")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220518005840.771575-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 823d81b0fa2cd83a640734e74caee338b5d3c093 upstream.
In br_dev_xmit() we perform vlan filtering in br_allowed_ingress() but
if the packet has the vlan header inside (e.g. bridge with disabled
tx-vlan-offload) then the vlan filtering code will use skb_vlan_untag()
to extract the vid before filtering which in turn calls pskb_may_pull()
and we may end up with a stale eth pointer. Moreover the cached eth header
pointer will generally be wrong after that operation. Remove the eth header
caching and just use eth_hdr() directly, the compiler does the right thing
and calculates it only once so we don't lose anything.
Fixes: 057658cb33 ("bridge: suppress arp pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Eduardo Vela <Nava> <evn@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd65e5a95d08389444e8591a20538b3edece0e15 upstream.
We need to clear all of the bridge private skb variables as they can be
stale due to the packet being recirculated through the stack and then
transmitted through the bridge device. Similar memset is already done on
bridge's input. We've seen cases where proxyarp_replied was 1 on routed
multicast packets transmitted through the bridge to ports with neigh
suppress which were getting dropped. Same thing can in theory happen with
the port isolation bit as well.
Fixes: 821f1b21ca ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Huang Guobin <huangguobin4@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 28b78ecffea8078d81466b2e01bb5a154509f1ba ]
This makes 'bridge-nf-filter-pppoe-tagged' sysctl work for
bridged traffic.
Looking at the original commit it doesn't appear this ever worked:
static unsigned int br_nf_post_routing(unsigned int hook, struct sk_buff **pskb,
[..]
if (skb->protocol == htons(ETH_P_8021Q)) {
skb_pull(skb, VLAN_HLEN);
skb->network_header += VLAN_HLEN;
+ } else if (skb->protocol == htons(ETH_P_PPP_SES)) {
+ skb_pull(skb, PPPOE_SES_HLEN);
+ skb->network_header += PPPOE_SES_HLEN;
}
[..]
NF_HOOK(... POST_ROUTING, ...)
... but the adjusted offsets are never restored.
The alternative would be to rip this code out for good,
but otoh we'd have to keep this anyway for the vlan handling
(which works because vlan tag info is in the skb, not the packet
payload).
Reported-and-tested-by: Amish Chana <amish@3g.co.za>
Fixes: 516299d2f5 ("[NETFILTER]: bridge-nf: filter bridged IPv4/IPv6 encapsulated in pppoe traffic")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe0b88064494b7bb6a9b2aa7e085b14a3112d44 ]
bridge_fill_linkxstats() is using nla_reserve_64bit().
We must use nla_total_size_64bit() instead of nla_total_size()
for corresponding data structure.
Fixes: 1080ab95e3 ("net: bridge: add support for IGMP/MLD stats and export them via netlink")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a019abd8022061b917da767cd1a66ed823724eab upstream.
Since commit 2796d0c648 ("bridge: Automatically manage
port promiscuous mode.")
bridges with `vlan_filtering 1` and only 1 auto-port don't
set IFF_PROMISC for unicast-filtering-capable ports.
Normally on port changes `br_manage_promisc` is called to
update the promisc flags and unicast filters if necessary,
but it cannot distinguish between *new* ports and ones
losing their promisc flag, and new ports end up not
receiving the MAC address list.
Fix this by calling `br_fdb_sync_static` in `br_add_if`
after the port promisc flags are updated and the unicast
filter was supposed to have been filled.
Fixes: 2796d0c648 ("bridge: Automatically manage port promiscuous mode.")
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04bef83a3358946bfc98a5ecebd1b0003d83d882 upstream.
When a PIM hello packet is received on a bridge port with multicast
snooping enabled, we mark it as a router port automatically, that
includes adding that port the router port list. The multicast lock
protects that list, but it is not acquired in the PIM message case
leading to a race condition, we need to take it to fix the race.
Cc: stable@vger.kernel.org
Fixes: 91b02d3d13 ("bridge: mcast: add router port on PIM hello message")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58e2071742e38f29f051b709a5cca014ba51166f upstream.
This patch fixes a tunnel_dst null pointer dereference due to lockless
access in the tunnel egress path. When deleting a vlan tunnel the
tunnel_dst pointer is set to NULL without waiting a grace period (i.e.
while it's still usable) and packets egressing are dereferencing it
without checking. Use READ/WRITE_ONCE to annotate the lockless use of
tunnel_id, use RCU for accessing tunnel_dst and make sure it is read
only once and checked in the egress path. The dst is already properly RCU
protected so we don't need to do anything fancy than to make sure
tunnel_id and tunnel_dst are read only once and checked in the egress path.
Cc: stable@vger.kernel.org
Fixes: 11538d039a ("bridge: vlan dst_metadata hooks in ingress and egress paths")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0353b4a96b7a9f60fe20d1b3ebd4931a4085f91c ]
Recently we had an interop issue where RARP packets got suppressed with
bridge neigh suppression enabled, but the check in the code was meant to
suppress GARP. Exclude RARP packets from it which would allow some VMWare
setups to work, to quote the report:
"Those RARP packets usually get generated by vMware to notify physical
switches when vMotion occurs. vMware may use random sip/tip or just use
sip=tip=0. So the RARP packet sometimes get properly flooded by the vtep
and other times get dropped by the logic"
Reported-by: Amer Abdalamer <amer@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8043c845b63a2dd88daf2d2d268a33e1872800f0 upstream.
Looking through patchwork I don't see that there was any consensus to
use switchdev notifiers only in case of netlink provided port flags but
not sysfs (as a sort of deprecation, punishment or anything like that),
so we should probably keep the user interface consistent in terms of
functionality.
http://patchwork.ozlabs.org/project/netdev/patch/20170605092043.3523-3-jiri@resnulli.us/http://patchwork.ozlabs.org/project/netdev/patch/20170608064428.4785-3-jiri@resnulli.us/
Fixes: 3922285d96 ("net: bridge: Add support for offloading port attributes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee4f52a8de2c6f78b01f10b4c330867d88c1653a ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f8ed289fab ("bridge: vlan: use br_vlan_(get|put)_master to deal with refcounts")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/1607071737-33875-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44f64f23bae2f0fad25503bc7ab86cd08d04cd47 ]
Netfilter changes PACKET_OTHERHOST to PACKET_HOST before invoking the
hooks as, while it's an expected value for a bridge, routing expects
PACKET_HOST. The change is undone later on after hook traversal. This
can be seen with pairs of functions updating skb>pkt_type and then
reverting it to its original value:
For hook NF_INET_PRE_ROUTING:
setup_pre_routing / br_nf_pre_routing_finish
For hook NF_INET_FORWARD:
br_nf_forward_ip / br_nf_forward_finish
But the third case where netfilter does this, for hook
NF_INET_POST_ROUTING, the packet type is changed in br_nf_post_routing
but never reverted. A comment says:
/* We assume any code from br_dev_queue_push_xmit onwards doesn't care
* about the value of skb->pkt_type. */
But when having a tunnel (say vxlan) attached to a bridge we have the
following call trace:
br_nf_pre_routing
br_nf_pre_routing_ipv6
br_nf_pre_routing_finish
br_nf_forward_ip
br_nf_forward_finish
br_nf_post_routing <- pkt_type is updated to PACKET_HOST
br_nf_dev_queue_xmit <- but not reverted to its original value
vxlan_xmit
vxlan_xmit_one
skb_tunnel_check_pmtu <- a check on pkt_type is performed
In this specific case, this creates issues such as when an ICMPv6 PTB
should be sent back. When CONFIG_BRIDGE_NETFILTER is enabled, the PTB
isn't sent (as skb_tunnel_check_pmtu checks if pkt_type is PACKET_HOST
and returns early).
If the comment is right and no one cares about the value of
skb->pkt_type after br_dev_queue_push_xmit (which isn't true), resetting
it to its original value should be safe.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20201123174902.622102-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a30ecc9237681bb125cbd30eee92bef7e86293d ]
In br_forward.c and br_input.c fields dev->stats.tx_dropped and
dev->stats.multicast are populated, but they are ignored in
ndo_get_stats64.
Fixes: 28172739f0 ("net: fix 64 bit counters on 32 bit arches")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/58ea9963-77ad-a7cf-8dfd-fc95ab95f606@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db7202dec92e6caa2706c21d6fc359af318bde2e ]
The eth_addr member is passed to ether_addr functions that require
2-byte alignment, therefore the member must be properly aligned
to avoid unaligned accesses.
The problem is in place since the initial merge of multicast to unicast:
commit 6db6f0eae6 bridge: multicast to unicast
Fixes: 6db6f0eae6 ("bridge: multicast to unicast")
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Martitz <t.martitz@avm.de>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 53fc685243bd6fb90d90305cea54598b78d3cbfc ]
When neighbor suppression is enabled the bridge device might reply to
Neighbor Solicitation (NS) messages on behalf of remote hosts.
In case the NS message includes the "Source link-layer address" option
[1], the bridge device will use the specified address as the link-layer
destination address in its reply.
To avoid an infinite loop, break out of the options parsing loop when
encountering an option with length zero and disregard the NS message.
This is consistent with the IPv6 ndisc code and RFC 4886 which states
that "Nodes MUST silently discard an ND packet that contains an option
with length zero" [2].
[1] https://tools.ietf.org/html/rfc4861#section-4.3
[2] https://tools.ietf.org/html/rfc4861#section-4.6
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alla Segal <allas@mellanox.com>
Tested-by: Alla Segal <allas@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9c284ec4b41c827f4369973d2792992849e4fa5 upstream.
Currently, using the bridge reject target with tagged packets
results in untagged packets being sent back.
Fix this by mirroring the vlan id as well.
Fixes: 85f5b3086a ("netfilter: bridge: add reject support")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 680f6af5337c98d116e4f127cea7845339dba8da ]
If userspace provides a rule blob with trailing data after last target,
we trigger a splat, then convert ruleset to 64bit format (with trailing
data), then pass that to do_replace_finish() which then returns -EINVAL.
Erroring out right away avoids the splat plus unneeded translation and
error unwind.
Fixes: 81e675c227 ("netfilter: ebtables: add CONFIG_COMPAT support")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd085ef678b2cc8c38c105673dfe8ff8f5ec0c57 ]
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e608f631f0ba5f1fc5ee2e260a3a35d13107cbfe upstream.
syzbot reported following splat:
BUG: KASAN: vmalloc-out-of-bounds in size_entry_mwt net/bridge/netfilter/ebtables.c:2063 [inline]
BUG: KASAN: vmalloc-out-of-bounds in compat_copy_entries+0x128b/0x1380 net/bridge/netfilter/ebtables.c:2155
Read of size 4 at addr ffffc900004461f4 by task syz-executor267/7937
CPU: 1 PID: 7937 Comm: syz-executor267 Not tainted 5.5.0-rc1-syzkaller #0
size_entry_mwt net/bridge/netfilter/ebtables.c:2063 [inline]
compat_copy_entries+0x128b/0x1380 net/bridge/netfilter/ebtables.c:2155
compat_do_replace+0x344/0x720 net/bridge/netfilter/ebtables.c:2249
compat_do_ebt_set_ctl+0x22f/0x27e net/bridge/netfilter/ebtables.c:2333
[..]
Because padding isn't considered during computation of ->buf_user_offset,
"total" is decremented by fewer bytes than it should.
Therefore, the first part of
if (*total < sizeof(*entry) || entry->next_offset < sizeof(*entry))
will pass, -- it should not have. This causes oob access:
entry->next_offset is past the vmalloced size.
Reject padding and check that computed user offset (sum of ebt_entry
structure plus all individual matches/watchers/targets) is same
value that userspace gave us as the offset of the next entry.
Reported-by: syzbot+f68108fed972453a0ad4@syzkaller.appspotmail.com
Fixes: 81e675c227 ("netfilter: ebtables: add CONFIG_COMPAT support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c4b4c421857dc7b1cf0dccbd738472360ff2cd70 ]
We have an interesting memory leak in the bridge when it is being
unregistered and is a slave to a master device which would change the
mac of its slaves on unregister (e.g. bond, team). This is a very
unusual setup but we do end up leaking 1 fdb entry because
dev_set_mac_address() would cause the bridge to insert the new mac address
into its table after all fdbs are flushed, i.e. after dellink() on the
bridge has finished and we call NETDEV_UNREGISTER the bond/team would
release it and will call dev_set_mac_address() to restore its original
address and that in turn will add an fdb in the bridge.
One fix is to check for the bridge dev's reg_state in its
ndo_set_mac_address callback and return an error if the bridge is not in
NETREG_REGISTERED.
Easy steps to reproduce:
1. add bond in mode != A/B
2. add any slave to the bond
3. add bridge dev as a slave to the bond
4. destroy the bridge device
Trace:
unreferenced object 0xffff888035c4d080 (size 128):
comm "ip", pid 4068, jiffies 4296209429 (age 1413.753s)
hex dump (first 32 bytes):
41 1d c9 36 80 88 ff ff 00 00 00 00 00 00 00 00 A..6............
d2 19 c9 5e 3f d7 00 00 00 00 00 00 00 00 00 00 ...^?...........
backtrace:
[<00000000ddb525dc>] kmem_cache_alloc+0x155/0x26f
[<00000000633ff1e0>] fdb_create+0x21/0x486 [bridge]
[<0000000092b17e9c>] fdb_insert+0x91/0xdc [bridge]
[<00000000f2a0f0ff>] br_fdb_change_mac_address+0xb3/0x175 [bridge]
[<000000001de02dbd>] br_stp_change_bridge_id+0xf/0xff [bridge]
[<00000000ac0e32b1>] br_set_mac_address+0x76/0x99 [bridge]
[<000000006846a77f>] dev_set_mac_address+0x63/0x9b
[<00000000d30738fc>] __bond_release_one+0x3f6/0x455 [bonding]
[<00000000fc7ec01d>] bond_netdev_event+0x2f2/0x400 [bonding]
[<00000000305d7795>] notifier_call_chain+0x38/0x56
[<0000000028885d4a>] call_netdevice_notifiers+0x1e/0x23
[<000000008279477b>] rollback_registered_many+0x353/0x6a4
[<0000000018ef753a>] unregister_netdevice_many+0x17/0x6f
[<00000000ba854b7a>] rtnl_delete_link+0x3c/0x43
[<00000000adf8618d>] rtnl_dellink+0x1dc/0x20a
[<000000009b6395fd>] rtnetlink_rcv_msg+0x23d/0x268
Fixes: 4359881338 ("bridge: add local MAC address to forwarding table (v2)")
Reported-by: syzbot+2add91c08eb181fea1bf@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b23c0742c2ce7e33ed79d10e451f70fdb5ca85d1 ]
xt_in() returns NULL in the output hook, skip the pkt_type change for
that case, redirection only makes sense in broute/prerouting hooks.
Reported-by: Tom Yan <tom.ty89@gmail.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: cf3cb246e2 ("bridge: ebtables: fix reception of frames DNAT-ed to bridge device/port")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f20faa06d83de440bec8e200870784c3458793c4 ]
The ordering of arguments to the x_tables ADD_COUNTER macro
appears to be wrong in ebtables (cf. ip_tables.c, ip6_tables.c,
and arp_tables.c).
This causes data corruption in the ebtables userspace tools
because they get incorrect packet & byte counts from the kernel.
Fixes: d72133e628 ("netfilter: ebtables: use ADD_COUNTER macro")
Signed-off-by: Todd Seidelmann <tseidelmann@linode.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94a72b3f024fc7e9ab640897a1e38583a470659d ]
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent at the end.
In fact, NLMSG_DONE is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 949f1e39a6 ("bridge: mdb: notify on router port add and del")
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15a78ba1844a8e052c1226f930133de4cef4e7ad ]
In compat_do_replace(), a temporary buffer is allocated through vmalloc()
to hold entries copied from the user space. The buffer address is firstly
saved to 'newinfo->entries', and later on assigned to 'entries_tmp'. Then
the entries in this temporary buffer is copied to the internal kernel
structure through compat_copy_entries(). If this copy process fails,
compat_do_replace() should be terminated. However, the allocated temporary
buffer is not freed on this path, leading to a memory leak.
To fix the bug, free the buffer before returning from compat_do_replace().
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3b48300d5cc7c7bed63fddb006c4046549ed4aec upstream.
ebtables doesn't include the base chain policies in the rule count,
so we need to add them manually when we call into the x_tables core
to allocate space for the comapt offset table.
This lead syzbot to trigger:
WARNING: CPU: 1 PID: 9012 at net/netfilter/x_tables.c:649
xt_compat_add_offset.cold+0x11/0x36 net/netfilter/x_tables.c:649
Reported-by: syzbot+276ddebab3382bbf72db@syzkaller.appspotmail.com
Fixes: 2035f3ff8eaa ("netfilter: ebtables: compat: un-break 32bit setsockopt when no rules are present")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5c725b6b65067909548ac9ca9bc777098ec9883d ]
When permanent entries were introduced by the commit below, they were
exempt from timing out and thus igmp leave wouldn't affect them unless
fast leave was enabled on the port which was added before permanent
entries existed. It shouldn't matter if fast leave is enabled or not
if the user added a permanent entry it shouldn't be deleted on igmp
leave.
Before:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
$
After:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
Fixes: ccb1c31a7a ("bridge: add flags to distinguish permanent mdb entires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7bae09fa008c6c9a489580db0a5a12063b97f97 ]
On initialization failure we have to delete the local fdb which was
inserted due to the default pvid creation. This problem has been present
since the inception of default_pvid. Note that currently there are 2 cases:
1) in br_dev_init() when br_multicast_init() fails
2) if register_netdevice() fails after calling ndo_init()
This patch takes care of both since br_vlan_flush() is called on both
occasions. Also the new fdb delete would be a no-op on normal bridge
device destruction since the local fdb would've been already flushed by
br_dev_delete(). This is not an issue for ports since nbp_vlan_init() is
called last when adding a port thus nothing can fail after it.
Reported-by: syzbot+88533dc8b582309bf3ee@syzkaller.appspotmail.com
Fixes: 5be5a2df40 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2446a68ae6a8cee6d480e2f5b52f5007c7c41312 ]
Don't cache eth dest pointer before calling pskb_may_pull.
Fixes: cf0f02d04a ("[BRIDGE]: use llc for receiving STP packets")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d26eb8ad1e9b906433903ce05f775cf038e747f ]
We would cache ether dst pointer on input in br_handle_frame_finish but
after the neigh suppress code that could lead to a stale pointer since
both ipv4 and ipv6 suppress code do pskb_may_pull. This means we have to
always reload it after the suppress code so there's no point in having
it cached just retrieve it directly.
Fixes: 057658cb33 ("bridge: suppress arp pkts on BR_NEIGH_SUPPRESS ports")
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b26a5d03d35d8f732d75951218983c0f7f68dff ]
We get a pointer to the ipv6 hdr in br_ip6_multicast_query but we may
call pskb_may_pull afterwards and end up using a stale pointer.
So use the header directly, it's just 1 place where it's needed.
Fixes: 08b202b672 ("bridge br_multicast: IPv6 MLD support.")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Martin Weinelt <martin@linuxlounge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bdfad5aec1392b93495b77b864d58d7f101dc1c1 ]
Currently error return from kobject_init_and_add() is not followed by a
call to kobject_put(). This means there is a memory leak. We currently
set p to NULL so that kfree() may be called on it as a noop, the code is
arguably clearer if we move the kfree() up closer to where it is
called (instead of after goto jump).
Remove a goto label 'err1' and jump to call to kobject_put() in error
return from kobject_init_and_add() fixing the memory leak. Re-name goto
label 'put_back' to 'err1' now that we don't use err1, following current
nomenclature (err1, err2 ...). Move call to kfree out of the error
code at bottom of function up to closer to where memory was allocated.
Add comment to clarify call to kfree().
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e166e4fdaced850bee3d5ee12a5740258fb30587 ]
Since Commit 21d1196a35 ("ipv4: set transport header earlier"),
skb->transport_header has been always set before entering INET
netfilter. This patch is to set skb->transport_header for bridge
before entering INET netfilter by bridge-nf-call-iptables.
It also fixes an issue that sctp_error() couldn't compute a right
csum due to unset skb->transport_header.
Fixes: e6d8b64b34 ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
commit 7caa56f006e9d712b44f27b32520c66420d5cbc6 upstream.
It means userspace gave us a ruleset where there is some other
data after the ebtables target but before the beginning of the next rule.
Fixes: 81e675c227 ("netfilter: ebtables: add CONFIG_COMPAT support")
Reported-by: syzbot+659574e7bcc7f7eb4df7@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5b493ce192bd7a4e7bd073b5685aad121eeef82 ]
br_multicast_start_querier() walks over the port list but it can be
called from a timer with only multicast_lock held which doesn't protect
the port list, so use RCU to walk over it.
Fixes: c83b8fab06 ("bridge: Restart queries when last querier expires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b2e2904deb314cc77a2192f506f2fd44e3d10d0 ]
When the commit below was introduced it changed two visible things:
- the skb was no longer passed through the protocol handlers with the
original device
- the skb was passed up the stack with skb->dev = bridge
The first change broke af_packet sockets on bridge ports. For example we
use them for hostapd which listens for ETH_P_PAE packets on the ports.
We discussed two possible fixes:
- create a clone and pass it through NF_HOOK(), act on the original skb
based on the result
- somehow signal to the caller from the okfn() that it was called,
meaning the skb is ok to be passed, which this patch is trying to
implement via returning 1 from the bridge link-local okfn()
Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and
drop/error would return < 0 thus the okfn() is called only when the
return was 1, so we signal to the caller that it was called by preserving
the return value from nf_hook().
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8e2f311a68494a6677c1724bdcb10bada21af37c ]
Following command:
iptables -D FORWARD -m physdev ...
causes connectivity loss in some setups.
Reason is that iptables userspace will probe kernel for the module revision
of the physdev patch, and physdev has an artificial dependency on
br_netfilter (xt_physdev use makes no sense unless a br_netfilter module
is loaded).
This causes the "phydev" module to be loaded, which in turn enables the
"call-iptables" infrastructure.
bridged packets might then get dropped by the iptables ruleset.
The better fix would be to change the "call-iptables" defaults to 0 and
enforce explicit setting to 1, but that breaks backwards compatibility.
This does the next best thing: add a request_module call to checkentry.
This was a stray '-D ... -m physdev' won't activate br_netfilter
anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d824548dae220820bdf69b2d1561b7c4b072783f upstream.
They are however frequently triggered by syzkaller, so remove them.
ebtables userspace should never trigger any of these, so there is little
value in making them pr_debug (or ratelimited).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2035f3ff8eaa29cfb5c8e2160b0f6e85eeb21a95 ]
Unlike ip(6)tables ebtables only counts user-defined chains.
The effect is that a 32bit ebtables binary on a 64bit kernel can do
'ebtables -N FOO' only after adding at least one rule, else the request
fails with -EINVAL.
This is a similar fix as done in
3f1e53abff ("netfilter: ebtables: don't attempt to allocate 0-sized compat array").
Fixes: 7d7d7e0211 ("netfilter: compat: reject huge allocation requests")
Reported-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 278e2148c07559dd4ad8602f22366d61eb2ee7b7 upstream.
This reverts commit 5a2de63fd1a5 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e267f ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e267f ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 710ae72877378e7cde611efd30fe90502a6e5b30 ]
Externally learned entries can be added by a user or by a switch driver
that is notifying the bridge driver about entries that were learned in
hardware.
In the first case, the entries are not marked with the 'added_by_user'
flag, which causes switch drivers to ignore them and not offload them.
The 'added_by_user' flag can be set on externally learned FDB entries
based on the 'swdev_notify' parameter in br_fdb_external_learn_add(),
which effectively means if the created / updated FDB entry was added by
a user or not.
Fixes: 816a3bed95 ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
