Move the ingress qdisc members of struct net_device from the transmit
cache line to the receive cache line to avoid cache line ping-pong.
These members are only used on the receive path.
Signed-off-by: Neil Turton <nturton@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race in Linux kernel file net/core/dev.c, function dev_close.
The function calls function dev_deactivate, which calls function
dev_watchdog_down that deletes the watchdog timer. However, after that, a
driver can call netif_carrier_ok, which calls function
__netdev_watchdog_up that can add the watchdog timer again. Function
unregister_netdevice calls function dev_shutdown that traps the bug
!timer_pending(&dev->watchdog_timer). Moving dev_deactivate after
netif_running() has been cleared prevents function netif_carrier_on
from calling __netdev_watchdog_up and adding the watchdog timer again.
Signed-off-by: Matti Linnanvuori <mattilinnanvuori@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro spotted a bogus use of u64 on the input sequence number which
is big-endian. This patch fixes it by giving the input sequence number
its own member in the xfrm_skb_cb structure.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In do_setlink() a single notification is sent at the end of the
function if any modification occured. If the address has been changed,
another notification is sent.
Both of them is required because originally only the NETDEV_CHANGEADDR
notification was sent and although device state change implies address
change, some programs may expect the original notification. It remains
for compatibity.
If set_operstate() is called from do_setlink(), it doesn't send a
notification, only if it is called from rtnl_create_link() as earlier.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one is called from under this config only, so move
it in the same place.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code declares variables on the stack, but uses them
under #ifdef CONFIG_IPV6, so thay become unused when ipv6
is off. Fortunately, they are used in a switch's case
branches, so the fix is rather simple.
Is it OK from coding style POV to add braces inside "cases",
or should I better avoid such style and rework the patch?
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The audit_log_start() will expand into an empty do { } while (0)
construction and the audit_ctx becomes unused.
The solution: push current->audit_context into audit_log_start()
directly, since it is not required in any other place in the
calling function.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The genl_unregister_family() calls the genl_unregister_mc_groups(),
which takes and releases the genl_lock and then locks and releases
this lock itself.
Relax this behavior, all the more so the genl_unregister_mc_groups()
is called from genl_unregister_family() only.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if the call to netlbl_domhsh_search succeeds the
return result will still be NULL.
Fix that, by returning the found entry (if any).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unused declaration of dflt_rt_lookup() method in
include/net/ndisc.h
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a long-standing bug in the IPsec IPv6 code that breaks
when we emit a IPsec tunnel-mode datagram packet. The problem
is that the code the emits the packet assumes the IPv6 stack
will fragment it later, but the IPv6 stack assumes that whoever
is emitting the packet is going to pre-fragment the packet.
In the long term we need to fix both sides, e.g., to get the
datagram code to pre-fragment as well as to get the IPv6 stack
to fragment locally generated tunnel-mode packet.
For now this patch does the second part which should make it
work for the IPsec host case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Blaschka provided the bug report and the initial suggested fix
for this bug. He also validated this version of this fix.
The problem is that the access to neigh->arp_queue is inconsistent, we
grab references when dropping the lock lock to call
neigh->ops->solicit() but this does not prevent other threads of
control from trying to send out that packet at the same time causing
corruptions because both code paths believe they have exclusive access
to the skb.
The best option seems to be to hold the write lock on neigh->lock
during the ->solicit() call. I looked at all of the ndisc_ops
implementations and this seems workable. The only case that needs
special care is the IPV4 ARP implementation of arp_solicit(). It
wants to take neigh->lock as a reader to protect the header entry in
neigh->ha during the emission of the soliciation. We can simply
remove the read lock calls to take care of that since holding the lock
as a writer at the caller providers a superset of the protection
afforded by the existing read locking.
The rest of the ->solicit() implementations don't care whether the
neigh is locked or not.
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjan:
With the help of kerneloops.org I've spotted a nice little interaction
between the TTY layer and the bluetooth code, however the tty layer is not
something I'm all too familiar with so I rather ask than brute-force fix the
code incorrectly.
The raw details are at:
http://www.kerneloops.org/search.php?search=uart_flush_buffer
What happens is that, on closing the bluetooth tty, the tty layer goes
into the release_dev() function, which first does a bunch of stuff, then
sets the file->private_data to NULL, does some more stuff and then calls the
ldisc close function. Which in this case, is hci_uart_tty_close().
Now, hci_uart_tty_close() calls hci_uart_close() which clears some
internal bit, and then calls hci_uart_flush()... which calls back to the
tty layers' uart_flush_buffer() function. (in drivers/bluetooth/hci_tty.c
around line 194) Which then WARN_ON()'s because that's not allowed/supposed
to be called this late in the shutdown of the port....
Should the bluetooth driver even call this flush function at all??
David:
This seems to be what happens: Hci_uart_close() flushes using
hci_uart_flush(). Subsequently, in hci_dev_do_close(), (one step in
hci_unregister_dev()), hci_uart_flush() is called again. The comment in
uart_flush_buffer(), relating to the WARN_ON(), indicates you can't flush
after the port is closed; which sounds reasonable. I think hci_uart_close()
should set hdev->flush to NULL before returning. Hci_dev_do_close() does
check for this. The code path is rather involved and I'm not entirely clear
of all steps, but I think that's what should be done.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes current use of: init_timer(), add_timer()
and del_timer() to setup_timer() with mod_timer(), which
should be safer anyway.
Reported-by: Jann Traschewski <jann@gmx.de>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to one of Jann's OOPS reports it looks like
BUG_ON(timer_pending(timer)) triggers during add_timer()
in ax25_start_t1timer(). This patch changes current use
of: init_timer(), add_timer() and del_timer() to
setup_timer() with mod_timer(), which should be safer
anyway.
Reported-by: Jann Traschewski <jann@gmx.de>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
> =================================
> [ INFO: inconsistent lock state ]
> 2.6.24-dg8ngn-p02 #1
> ---------------------------------
> inconsistent {softirq-on-W} -> {in-softirq-R} usage.
> linuxnet/3046 [HC0[0]:SC1[2]:HE1:SE0] takes:
> (ax25_route_lock){--.+}, at: [<f8a0cfb7>] ax25_get_route+0x18/0xb7 [ax25]
> {softirq-on-W} state was registered at:
...
This lockdep report shows that ax25_route_lock is taken for reading in
softirq context, and for writing in process context with BHs enabled.
So, to make this safe, all write_locks in ax25_route.c are changed to
_bh versions.
Reported-by: Jann Traschewski <jann@gmx.de>,
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This lockdep warning:
> =======================================================
> [ INFO: possible circular locking dependency detected ]
> 2.6.24 #3
> -------------------------------------------------------
> swapper/0 is trying to acquire lock:
> (ax25_list_lock){-+..}, at: [<f91dd3b1>] ax25_destroy_socket+0x171/0x1f0 [ax25]
>
> but task is already holding lock:
> (slock-AF_AX25){-+..}, at: [<f91dbabc>] ax25_std_heartbeat_expiry+0x1c/0xe0 [ax25]
>
> which lock already depends on the new lock.
...
shows that ax25_list_lock and slock-AF_AX25 are taken in different
order: ax25_info_show() takes slock (bh_lock_sock(ax25->sk)) while
ax25_list_lock is held, so reversely to other functions. To fix this
the sock lock should be moved to ax25_info_start(), and there would
be still problem with breaking ax25_list_lock (it seems this "proper"
order isn't optimal yet). But, since it's only for reading proc info
it seems this is not necessary (e.g. ax25_send_to_raw() does similar
reading without this lock too).
So, this patch removes sock lock to avoid deadlock possibility; there
is also used sock_i_ino() function, which reads sk_socket under proper
read lock. Additionally printf format of this i_ino is changed to %lu.
Reported-by: Bernard Pidoux F6BVP <f6bvp@free.fr>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use key/offset caching to change /proc/net/route (use by iputils route)
from O(n^2) to O(n). This improves performance from 30sec with 160,000
routes to 1sec.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes possible problems when trie_firstleaf() returns NULL
to trie_leafindex().
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various RFCs have all sorts of things to say about the CS field of the
DSCP value. In particular they try to make the distinction between
values that should be used by "user applications" and things like
routing daemons.
This seems to have influenced the CAP_NET_ADMIN check which exists for
IP_TOS socket option settings, but in fact it has an off-by-one error
so it wasn't allowing CS5 which is meant for "user applications" as
well.
Further adding to the inconsistency and brokenness here, IPV6 does not
validate the DSCP values specified for the IPV6_TCLASS socket option.
The real actual uses of these TOS values are system specific in the
final analysis, and these RFC recommendations are just that, "a
recommendation". In fact the standards very purposefully use
"SHOULD" and "SHOULD NOT" when describing how these values can be
used.
In the final analysis the only clean way to provide consistency here
is to remove the CAP_NET_ADMIN check. The alternatives just don't
work out:
1) If we add the CAP_NET_ADMIN check to ipv6, this can break existing
setups.
2) If we just fix the off-by-one error in the class comparison in
IPV4, certain DSCP values can be used in IPV6 but not IPV4 by
default. So people will just ask for a sysctl asking to
override that.
I checked several other freely available kernel trees and they
do not make any privilege checks in this area like we do. For
the BSD stacks, this goes back all the way to Stevens Volume 2
and beyond.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9af57b7a ("IB/cm: Add basic performance counters") introduced a
bug in how the reference count for cm_class.subsys.kobj was handled:
the path that released a device did a kobject_put() on that kobject, but
there was no kobject_get() in the path the handles adding a device. So
the reference count ended up too low, which leads to bad things. Fix up
and simplify the reference counting to avoid this.
(Actually, I introduced the bug when fixing the patch up to match some
of Greg's kobject changes, but who's counting)
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Usually harmless, since the scatterlist is always hard-coded to a length
of 1, but it triggers a BUG() if CONFIG_DEBUG_SG=y, so we better fix it.
This fixes <http://bugzilla.kernel.org/show_bug.cgi?id=9934>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The USEC_TO_HZ and HZ_TO_USEC constant sets were mislabelled, with
seriously incorrect results. This among other things manifested
itself as cpufreq not working when a tickless kernel was configured.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Carlos R. Mafra <crmafra@ift.unesp.br>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It looks like there's been a bug in the module parameter setup forever.
The upshot doesn't really matter, because even if no parameters are ever
set, we just call sym53c416_setup() three times, but the zero values in
the arrays eventually cause nothing to happen. Unfortunately gcc has
started to notice this now too:
drivers/scsi/sym53c416.c: In function 'sym53c416_detect':
drivers/scsi/sym53c416.c:624: warning: the address of 'sym53c416' will always evaluate as 'true'
drivers/scsi/sym53c416.c:630: warning: the address of 'sym53c416_1' will always evaluate as 'true'
drivers/scsi/sym53c416.c:636: warning: the address of 'sym53c416_2' will always evaluate as 'true'
drivers/scsi/sym53c416.c:642: warning: the address of 'sym53c416_3' will always evaluate as 'true'
So fix this longstanding bug to keep gcc quiet.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Even if we don't want to register the WMI driver, we should initialize
the wmi_blocks list to be empty, since we don't want the wmi helper
functions to oops just because that basic list has not even been set up.
With this, "find_guid()" will happily return "not found" rather than
oopsing all over the place, and the callers will then just automatically
return false or AE_NOT_FOUND as appropriate.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The makefile magic for installing the 32-bit vdso images on disk had a
little error. A single-line change would fix that bug, but this does a
little more to reduce the error-prone duplication of this bit of
makefile variable magic.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kosaki Motohito noted that "numactl --interleave=all ..." failed in the
presence of memoryless nodes. This patch attempts to fix that problem.
Some background:
numactl --interleave=all calls set_mempolicy(2) with a fully populated
[out to MAXNUMNODES] nodemask. set_mempolicy() [in do_set_mempolicy()]
calls contextualize_policy() which requires that the nodemask be a
subset of the current task's mems_allowed; else EINVAL will be returned.
A task's mems_allowed will always be a subset of node_states[N_HIGH_MEMORY]
i.e., nodes with memory. So, a fully populated nodemask will be
declared invalid if it includes memoryless nodes.
NOTE: the same thing will occur when running in a cpuset
with restricted mem_allowed--for the same reason:
node mask contains dis-allowed nodes.
mbind(2), on the other hand, just masks off any nodes in the nodemask
that are not included in the caller's mems_allowed.
In each case [mbind() and set_mempolicy()], mpol_check_policy() will
complain [again, resulting in EINVAL] if the nodemask contains any
memoryless nodes. This is somewhat redundant as mpol_new() will remove
memoryless nodes for interleave policy, as will bind_zonelist()--called
by mpol_new() for BIND policy.
Proposed fix:
1) modify contextualize_policy logic to:
a) remember whether the incoming node mask is empty.
b) if not, restrict the nodemask to allowed nodes, as is
currently done in-line for mbind(). This guarantees
that the resulting mask includes only nodes with memory.
NOTE: this is a [benign, IMO] change in behavior for
set_mempolicy(). Dis-allowed nodes will be
silently ignored, rather than returning an error.
c) fold this code into mpol_check_policy(), replace 2 calls to
contextualize_policy() to call mpol_check_policy() directly
and remove contextualize_policy().
2) In existing mpol_check_policy() logic, after "contextualization":
a) MPOL_DEFAULT: require that in coming mask "was_empty"
b) MPOL_{BIND|INTERLEAVE}: require that contextualized nodemask
contains at least one node.
c) add a case for MPOL_PREFERRED: if in coming was not empty
and resulting mask IS empty, user specified invalid nodes.
Return EINVAL.
c) remove the now redundant check for memoryless nodes
3) remove the now redundant masking of policy nodes for interleave
policy from mpol_new().
4) Now that mpol_check_policy() contextualizes the nodemask, remove
the in-line nodes_and() from sys_mbind(). I believe that this
restores mbind() to the behavior before the memoryless-nodes
patch series. E.g., we'll no longer treat an invalid nodemask
with MPOL_PREFERRED as local allocation.
[ Patch history:
v1 -> v2:
- Communicate whether or not incoming node mask was empty to
mpol_check_policy() for better error checking.
- As suggested by David Rientjes, remove the now unused
cpuset_nodes_subset_current_mems_allowed() from cpuset.h
v2 -> v3:
- As suggested by Kosaki Motohito, fold the "contextualization"
of policy nodemask into mpol_check_policy(). Looks a little
cleaner. ]
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
So I spent a while pounding my head against my monitor trying to figure
out the vmsplice() vulnerability - how could a failure to check for
*read* access turn into a root exploit? It turns out that it's a buffer
overflow problem which is made easy by the way get_user_pages() is
coded.
In particular, "len" is a signed int, and it is only checked at the
*end* of a do {} while() loop. So, if it is passed in as zero, the loop
will execute once and decrement len to -1. At that point, the loop will
proceed until the next invalid address is found; in the process, it will
likely overflow the pages array passed in to get_user_pages().
I think that, if get_user_pages() has been asked to grab zero pages,
that's what it should do. Thus this patch; it is, among other things,
enough to block the (already fixed) root exploit and any others which
might be lurking in similar code. I also think that the number of pages
should be unsigned, but changing the prototype of this function probably
requires some more careful review.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matt is already the maintainer of SLOB which is one of the "SLAB" allocators in
the kernel so add him to MAINTAINERS.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: platform driver allocs dma without create
pata_ninja32: setup changes
pata_legacy: typo fix
pata_amd: Note in the module description it handles Nvidia
sata_mv: fix loop with last port
libata: ignore deverr on SETXFER if mode is configured
pata_via: fix SATA cable detection on cx700
This avoids warnings with unreferenced variables in the !NUMA case.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update lpfc driver version to 8.2.5
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous fixes:
- Fix ERRATT flag which was overlapping
- Allow RESTART mbx commands through when stopped.
- Accept incoming PLOGI when connected to an N_Port.
- Fix NPort to NPort pt2pt problems: ADISC and reg_vpi issues
- Fix vport unloading error that erroneously cleaned up RSCN buffers
- Fix memory leak during repeated unloads - in mbox handling
- Fix link bounce vs FLOGI race conditions
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct ndlp referencing issues:
- Fix ndlp kref issues due to race conditions between threads
- Fix cancel els delay retry event which missed an ndlp reference count
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 313abe55 ("mlx4_core: For 64-bit systems, vmap() kernel queue
buffers") caused this to pop up on powerpc allyesconfig, looks like a
missing include file:
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_alloc':
drivers/net/mlx4/alloc.c:162: error: implicit declaration of function 'vmap'
drivers/net/mlx4/alloc.c:162: error: 'VM_MAP' undeclared (first use in this function)
drivers/net/mlx4/alloc.c:162: error: (Each undeclared identifier is reported only once
drivers/net/mlx4/alloc.c:162: error: for each function it appears in.)
drivers/net/mlx4/alloc.c:162: warning: assignment makes pointer from integer without a cast
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_free':
drivers/net/mlx4/alloc.c:187: error: implicit declaration of function 'vunmap'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit bdc807871d broke the build
for this config because the sim_defconfig selects CONFIG_HZ=250
but include/asm-ia64/param.h has an ifdef for the simulator to
force HZ to 32. So we ended up with a kernel/timeconst.h set
for HZ=250 ... which then failed the check for the right HZ
value and died with:
Drop the #ifdef magic from param.h and make force CONFIG_HZ=32
directly for the simulator.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since the sg chaining patches went in, our current value of 255 for
SG_ALL excites chaining on some drivers which cannot support it (and
would thus oops). Redefine SG_ALL to mean no sg table size
preference, but use the single allocation (non chained) limit. This
also helps for drivers that use it to size an internal table.
We'll do an opt in system later where truly chaining supporting
drivers can define their sg_tablesize to be anything up to
SCSI_MAX_SG_CHAIN_ELEMENTS.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
include/scsi/scsi.h as a definition:
#define ABORT_TASK 0x0d
on the other hand drivers/scsi/aic94xx/aic94xx_sas.h has:
#define ABORT_TASK 0x03
rename the latter to SCB_ABORT_TASK
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When the sata_mv driver is used as a platform driver,
mv_create_dma_pools() is never called so it fails when trying
to alloc in mv_pool_start().
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Forcibly set more of the configuration at init time. This seems to fix at
least one problem reported. We don't know what most of these bits do, but
we do know what windows stuffs there.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
