Rename NET_SB1250_MAC to SB1250_MAC to follow the convention.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PCI controller IO base was not set in the au1000 pci code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes a wrong ifdef in the board setup code, leading to the GPIO
pin not being pulled high, and thus the USB switch not being powered at all.
This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which
started in 2005 (before 2.6.12-rc2), then probably because things were
working anyway for most people got forgotten.
[Ralf: Paolo's original patch didn't fix the module case, Florian's patch
only fixed MTX1 etc. so this is a combined patch plus some cleanups.]
Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixe MACE PCI addressing by adding the bus number parameter.
Remove check of the used slot since every slot should be valid.
Converted mkaddr from #define to inline function.
Signed-off-by: Giuseppe Sacco <eppesuig@debian.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Restore a load from KSEG1 done as a workaround for an R4600 v2
erratum, dropped with 211be16de99a7424e66c0b6c0d00e2c970508ac2.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Store any note sections after the exception tables like the other
architectures do. This is required for .note.gnu.build-id emitted from
binutils 2.18 onwards if nothing else.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS was mistakenly forgetting to use the fallocate compat wrapper, which
I noticed while cleaning up all the duplicate fallocate wrappers.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a workaround to address warnings generated on the "n" constraint by
GCC 3.3 and below.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the definition of the ioasic_ssr_lock spinlock to include a proper
initialisation.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Another issue with 20Kc's WAIT, waiting for more details. With the
2.6.23 release immindent simply disable the use of WAIT instead of a
more fancy workaround.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fairly cosmetic as it would only affect VSMP / SMTC kernels that don't
use vectored interrupts.
Found by Beth.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It refer to CPU_PROFILING.
arch/mips/kernel/time.c: In function 'local_timer_interrupt':
arch/mips/kernel/time.c:142: error: implicit declaration of function 'profile_tick'
arch/mips/kernel/time.c:142: error: 'CPU_PROFILING' undeclared (first use in this function)
arch/mips/kernel/time.c:142: error: (Each undeclared identifier is reported only once
arch/mips/kernel/time.c:142: error: for each function it appears in.)
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/kernel/rtlx.o
cc1: warnings being treated as errors
arch/mips/kernel/rtlx.c:59: warning: 'irq' defined but not used
arch/mips/kernel/rtlx.c:60: warning: 'irq_num' defined but not used
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/kernel/rtlx.o
arch/mips/kernel/rtlx.c: In function 'rtlx_init':
arch/mips/kernel/rtlx.c:114: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Copy_user_highpage was written assuming it was only being called for
breaking COW pages in which case the source page isn't cached as in
marked cachable under it kernel virtual address. If it is called anyway
the aliasing avoidance strategy implemented by kmap_coherent will fail.
Avoid the use of kmap_coherent for pages marked dirty and to avoid
another instance of this sort of bug, place a BUG_ON in kmap_coherent.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix wrong argument order; this is just a minimal fix for the half baked
redadb/writeb() conversion.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Wrong check for the second hpc on fullhouse machines, caused DBEs on
SGI Indys
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sibyte/bcm1480/irq.o
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_mask_irq':
arch/mips/sibyte/bcm1480/irq.c:112: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:114: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_unmask_irq':
arch/mips/sibyte/bcm1480/irq.c:130: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:132: warning: cast to pointer from integer of different size
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct the name of the spi_txx9 driver (and their in-tree user)
instead of MODULE_ALIAS workaround. This would be preferable in the
long term.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
shutdown_bridge_irq disconnects the irq so we need to connect the irq or
requesting the same irq a send time will fail. This used to make
things like ifconfig eth0 down; ifconfig eth0 up fail on IP27.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Certain 32-bit kernel configurations seem to be able to cause references,
this was observed with gcc 4.1.2.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d several callers of
pcibios_resource_to_bus are no longer marked __devinit resulting in a
pile of modpost warnings if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x15dde8): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_map_rom' and 'pci_map_rom_copy')
WARNING: vmlinux.o(.text+0x15e140): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_update_resource' and 'pci_claim_resource')
WARNING: vmlinux.o(.text+0x15f0cc): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f0f0): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f114): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f138): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f438): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
WARNING: vmlinux.o(.text+0x15f4f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
Removing __devinit from pcibios_resource_to_bus make the same necessary
for pcibios_fixup_device_resources as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d pcibios_fixup_bus's caller
pci_scan_child_bus is no longer marked __devinit resulting in this modpost
warning if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x158b9c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The appended patch adds code to update siginfo_t's si_code field. It
fixes e.g. a floating point overflow regression in the SBCL testsuite.
Signed-off-By: Thiemo Seufer <ths@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also removes the while(1); loop by propagating the ATTRIB_NORET of die()
to nmi_exception_handler.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rtc-rs5c348 SPI driver name doesn't match its module name, which
prevents it from properly hotplugging. There is only one in-tree user
of its driver, which is fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/basler/excite/excite_prom.o
arch/mips/basler/excite/excite_prom.c:136:3: #error 64 bit support not implemented
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS doesn't do CPU hotplugging yet but since many of the functions don't
even have an __init let's fix this right.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leaving these sections is useful to some tools that look at the image, and
none of them are loaded into memory. The .mdebug.abi64 section, in
particular, lets GDB recognize vmlinux.32 as an N64 program instead of
guessing that it is O32.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add generic irq_chip for TX39/TX49 SoCs. This can be replace
jmr3927_irq_irc, tx4927_irq_pic_type and tx4938_irq_pic_type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is needed since the Sibyte serial driver was exchanged.
Issue report by Imre Kaloz <kaloz@openwrt.org>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the other archs, there is more factoring of smp call code, and more care
in the use of get_cpu(). That can be a follow-up MIPS patch.
Signed-off-by: Peter Watkins <pwatkins@sicortex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/kernel/machine_kexec.c: In function 'machine_kexec':
arch/mips/kernel/machine_kexec.c:54: warning: assignment makes integer from pointer without a cast
arch/mips/kernel/machine_kexec.c:70: warning: assignment makes integer from pointer without a cast
arch/mips/kernel/machine_kexec.c:81: warning: format '%08x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unlike the current code suggests, the RaQ1 actually has an UART. Only
the Qube1 (Qube 2700) lacks one.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes some duplicate includes from arch/mips/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The new type of irq handler remove a parameter (struct pt_regs *),but
someone forgot to supply it.
Signed-off-by: Dajie Tan <jiankemeng@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pmc-sierra/yosemite/smp.c: In function 'titan_mailbox_irq':
arch/mips/pmc-sierra/yosemite/smp.c:112: warning: 'status' may be used uninitialized in this function
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pmc-sierra/yosemite/i2c-yosemite.c: In function 'titan_i2c_xfer':
arch/mips/pmc-sierra/yosemite/i2c-yosemite.c:98: warning: 'data' may be used uninitialized in this function
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit e436d80085
Author: Ingo Molnar <mingo@elte.hu>
Date: Thu Jul 19 21:28:35 2007 +0200
[PATCH] sched: implement cpu_clock(cpu) high-speed time source
broke the build of several MIPS platforms which were already using the
symbol cpu_clock for the own purposes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
linux/arch/mips/pci/fixup-tx4938.c:21:5: warning: symbol 'pci_get_irq' was not declared. Should it be static?
linux/arch/mips/pci/fixup-tx4938.c:76: warning: passing argument 1 of 'pci_get_irq' discards qualifiers from pointer target type
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When comparing a pointer, it's clearer to compare it to NULL than to 0.
Here is an excerpt of the semantic patch:
@@
expression *E;
@@
E ==
- 0
+ NULL
@@
expression *E;
@@
E !=
- 0
+ NULL
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: akpm@linux-foundation.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
__INIT directive just before kernel_entry was ignored for most platforms.
This patch fixes it and get rid of this warning:
WARNING: vmlinux.o(.text+0x478): Section mismatch: reference to .init.text:start_kernel (between '_stext' and 'run_init_process')
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can make resources for platform_device_register_simple() "static
__initdata".
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replaces the deprecated __attribute_used__ with __used. Also makes some
style adjustments to abide by the kernel coding conventions.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
> WARNING: vmlinux.o(.text+0xbf20): Section mismatch: reference to
> .init.text:prom_free_prom_memory (between 'free_initmem' and 'copy_from_user_page')
prom_free_prom_memory() is called _before_ freeing init sections, so
it is false positive. __init_refok can be used for such cases.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
per cpu data section contains two types of data. One set which is
exclusively accessed by the local cpu and the other set which is per cpu,
but also shared by remote cpus. In the current kernel, these two sets are
not clearely separated out. This can potentially cause the same data
cacheline shared between the two sets of data, which will result in
unnecessary bouncing of the cacheline between cpus.
One way to fix the problem is to cacheline align the remotely accessed per
cpu data, both at the beginning and at the end. Because of the padding at
both ends, this will likely cause some memory wastage and also the
interface to achieve this is not clean.
This patch:
Moves the remotely accessed per cpu data (which is currently marked
as ____cacheline_aligned_in_smp) into a different section, where all the data
elements are cacheline aligned. And as such, this differentiates the local
only data and remotely accessed data cleanly.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer. This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).
[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
early_serial_setup was removed from serial.h, but forgot to put in
serial_8250.h
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the SB1250 DUART, a dual serial port implementation
included in the Broadcom family of SOCs descending from the SiByte SB1250
MIPS64 chip multiprocessor. It is a new implementation replacing the
old-fashioned driver currently present in the linux-mips.org tree. It
supports all the usual features one would expect from a(n asynchronous)
serial driver, including modem line control (as far as hardware supports it
-- there is edge detection logic missing from the DCD and RI lines and the
driver does not implement polling of these lines at the moment), the serial
console, BREAK transmission and reception, including the magic SysRq. The
receive FIFO threshold is not maintained though.
The driver was tested with a SWARM board which uses a BCM1250 SOC (which is
dual MIPS64 CMP) and has both ports of the single DUART implemented wired
externally. Both were tested. Testing included using the ports as
terminal lines at 1200bps (which is the ports minimum), 115200bps and a
couple of random speeds inbetween. The modem lines were verified to
operate correctly. No testing was performed with a use as a network
interface, like with SLIP or PPP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical implementations of PTRACE_POKEDATA go into generic_ptrace_pokedata()
function.
AFAICS, fix bug on xtensa where successful PTRACE_POKEDATA will nevertheless
return EPERM.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kernel OOPSed or BUGed then it probably should be considered as
tainted. Thus, all subsequent OOPSes and SysRq dumps will report the
tainted kernel. This saves a lot of time explaining oddities in the
calltraces.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Added parisc patch from Matthew Wilson -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Declaring emulpc and contpc as "unsigned long" can get rid of some casts.
This also get rid of some sparse warnings.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
While the PC speaker is wired up to the i8254 there is more to the i8254
than just the PC speaker so this code was getting in the way under its
current name.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The only pseudo-legitimate MIPS user of genrtc was a systems that doesn't
have an RTC in hardware at all. At this point faking one is a little
pointless ...
Fixes this warning:
arch/mips/pci/pci.c:284:18: warning: symbol 'dev' shadows an earlier one
arch/mips/pci/pci.c:272:17: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To support multiple TC microthreads acting as "CPUs" within a VPE,
VPE-wide interrupt mask bits must be specially manipulated during
interrupt handling. To support legacy drivers and interrupt controller
management code, SMTC has a "backstop" to track and if necessary restore
the interrupt mask. This has some performance impact on interrupt service
overhead. Disable it only if you know what you are doing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes this sparse warning:
arch/mips/lib/uncached.c:38:22: warning: symbol 'run_uncached' was not declared. Should it be static?
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also include tlbdebug.h in dump_tlb.c and r3k_dump_tlb.c.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use physical address for 82596 and 53c710 base address
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Based on replies to a respective query, remove the pci_dac_dma_...() APIs
(except for pci_dac_dma_supported() on Alpha, where this function is used
in non-DAC PCI DMA code).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Jesse Barnes <jesse.barnes@intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Acked-by: David Miller <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a slightly cleaner way of creating the /proc structure for the
pnx8850. mostly, it creates a directory with default mode 555, since the
one you're creating is mode 444, which is somewhat unusual for a directory
under /proc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Using another systems defines is a safe way to get your code broken by
accident when that system is removed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Export contents of struct mips_fpu_emulator_stats via debugfs.
There is no way to read these statistics for now but they (at least
the "emulated" count) might be sometimes useful for performance tuning
on FPU-less CPUs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently a number of unaligned instructions is counted but not used.
Add /debug/mips/unaligned_instructions file to show the value.
And add /debug/mips/unaligned_action to control behavior upon an
unaligned access. Possible actions are:
0: silently fixup the unaligned access.
1: send SIGBUS.
2: dump registers, process name, etc. and fixup.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Fix pci ops for secondary PCIC
* Do not reserve 1MB for PCI MEM region (leave PCIBIOS_MIN_MEM zero)
* Use platform_device to provide ethernet addresses for internal NICs.
(background: TX49XX SoCs include PCI NIC (TC35815 compatible)
connected via its internal PCI bus, but the NIC's PROM interface is
not connected to SEEPROM. So we must provide its ethernet address
by another way.)
* Check return value of early_read_config_word()
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX39XX and TX49XX have "reserved" segment in CKSEG3 area.
0xff000000-0xff3fffff on TX49XX and 0xff000000-0xfffeffff on TX39XX
are reserved (unmapped, uncached). Controllers on these SoCs are
placed in this segment.
This patch add plat_ioremap() and plat_iounmap() to override default
behavior and implement these hooks for TX39/TX49.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use rtc-rs5c348 and at25 spi protocol driver and spi_txx9 spi
controller driver instead of platform dependent codes.
This patch also removes dependencies to old RTC interfaces such as
rtc_mips_get_time, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GPIO 0..15 are for TX4938 PIO pins, GPIO 16..18 are for FPGA-driven
chipselect signals for SPI devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add default configuration for the PMC-Sierra
MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add PCI support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add mips common support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add core platform support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Which will cut down the cost of RDHWR $29 which is used to obtain the
TLS pointer and so far being emulated in software down to a single cycle
operation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to break the code of people who think they are supposed to scribble
into the pci device structure - it's off limits.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are no I/O ports on the DECstation whatsoever in any configuration
as neither the CPU nor the peripheral buses used have a concept of such.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable Cobalt button support and change ATA driver from BLK_DEV_VIA82CXXX
to PATA_VIA..
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert old/obsolete NORET_TYPE and ATTRIB_NORET macros to use the
newer standard of "__noreturn" as defined in compiler-gcc.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use standard missing-syscalls with EXTRA_CFLAGS instead of duplicating
the command. And move the archprepare rule before the archclean rule.
Suggested by Franck Bui-Huu. Also add "echo" to show the target ABI.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
the SMP load-balancer uses the boot-time migration-cost estimation
code to attempt to improve the quality of balancing. The reason for
this code is that the discrete priority queues do not preserve
the order of scheduling accurately, so the load-balancer skips
tasks that were running on a CPU 'recently'.
this code is fundamental fragile: the boot-time migration cost detector
doesnt really work on systems that had large L3 caches, it caused boot
delays on large systems and the whole cache-hot concept made the
balancing code pretty undeterministic as well.
(and hey, i wrote most of it, so i can say it out loud that it sucks ;-)
under CFS the same purpose of cache affinity can be achieved without
any special cache-hot special-case: tasks are sorted in the 'timeline'
tree and the SMP balancer picks tasks from the left side of the
tree, thus the most cache-cold task is balanced automatically.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The idle loop goes to sleep using the WAIT instruction if !need_resched().
This has is suffering from from a race condition that if if just after
need_resched has returned 0 an interrupt might set TIF_NEED_RESCHED but
we've just completed the test so go to sleep anyway. This would be
trivial to fix by just disabling interrupts during that sequence as in:
local_irq_disable();
if (!need_resched())
__asm__("wait");
local_irq_enable();
but the processor architecture leaves it undefined if a processor calling
WAIT with interrupts disabled will ever restart its pipeline and indeed
some processors have made use of the freedom provided by the architecture
definition. This has been resolved and the Config7.WII bit indicates that
the use of WAIT is safe on 24K, 24KE and 34K cores. It also is safe on
74K starting revision 2.1.0 so enable the use of WAIT with interrupts
disabled for 74K based on a c0_prid of at least that.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported by Eugene Surovegin <ebs@ebshome.net>.
If only modules were users of these functions they did not get linked into
the kernel proper, so later module loads would fail as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
C0_status doesn't need to be initialized at this point anyway; the register
will be initialized later.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Neither rtc_mips_get_time nor rtc_mips_set_time are being initialized by
the EMMA2RH setup code, so genrtc at best was a RTC dummy avoiding a few
error messages but not providing actual functionality.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We used to avoid the WAIT entirely on the 20K but really only need to do
this on early revs of the 20K. Without this a 20K was a bit of a
power hog. Well, in the lower power power hog category ;-)
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For some platforms it's definitions may conflict. So that's the one-liner.
The rest is 10 square kilometers of collateral damage fixup this include
used to paper over.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support for performance counter overflow interrupt that is on a separate
interrupt from the timer.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And an attempt to tidy up the core/controller differences.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
