Switch ingress queueing back to use ingress_lock. qdisc_lock_tree now locks
both the ingress and egress qdiscs on the device. All changes to data that
might be used on both ingress and egress needs to be protected by using
qdisc_lock_tree instead of manually taking dev->queue_lock. Additionally
the qdisc stats_lock needs to be initialized to ingress_lock for ingress
qdiscs.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're now holding the rtnl during the entire dump operation, we
can remove qdisc_tree_lock, whose only purpose is to protect dump
callbacks from concurrent changes to the qdisc tree.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces users of the round_jiffies() function in the
networking code.
These timers all were of the "about once a second" or "about once
every X seconds" variety and several showed up in the "what wakes the
cpu up" profiles that the tickless patches provide. Some timers are
highly dynamic based on network load; but even on low activity systems
they still show up so the rounding is done only in cases of low
activity, allowing higher frequency timers in the high activity case.
The various hardware watchdogs are an obvious case; they run every 2
seconds but aren't otherwise specific of exactly when they need to
run.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the following unused EXPORT_SYMBOL's:
- sch_api.c: qdisc_lookup
- sch_generic.c: __netdev_watchdog_up
- sch_generic.c: noop_qdisc_ops
- sch_generic.c: qdisc_alloc
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set parent classids in default qdiscs to allow walking up the tree
from outside the qdiscs. This is needed by the next patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The move of qdisc destruction to a rcu callback broke locking in the
entire qdisc layer by invalidating previously valid assumptions about
the context in which changes to the qdisc tree occur.
The two assumptions were:
- since changes only happen in process context, read_lock doesn't need
bottem half protection. Now invalid since destruction of inner qdiscs,
classifiers, actions and estimators happens in the RCU callback unless
they're manually deleted, resulting in dead-locks when read_lock in
process context is interrupted by write_lock_bh in bottem half context.
- since changes only happen under the RTNL, no additional locking is
necessary for data not used during packet processing (f.e. u32_list).
Again, since destruction now happens in the RCU callback, this assumption
is not valid anymore, causing races while using this data, which can
result in corruption or use-after-free.
Instead of "fixing" this by disabling bottem halfs everywhere and adding
new locks/refcounting, this patch makes these assumptions valid again by
moving destruction back to process context. Since only the dev->qdisc
pointer is protected by RCU, but ->enqueue and the qdisc tree are still
protected by dev->qdisc_lock, destruction of the tree can be performed
immediately and only the final free needs to happen in the rcu callback
to make sure dev_queue_xmit doesn't access already freed memory.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix lockdep warning with GRE, iptables and Speedtouch ADSL, PPP over ATM.
On Sat, Sep 02, 2006 at 08:39:28PM +0000, Krzysztof Halasa wrote:
>
> =======================================================
> [ INFO: possible circular locking dependency detected ]
> -------------------------------------------------------
> swapper/0 is trying to acquire lock:
> (&dev->queue_lock){-+..}, at: [<c02c8c46>] dev_queue_xmit+0x56/0x290
>
> but task is already holding lock:
> (&dev->_xmit_lock){-+..}, at: [<c02c8e14>] dev_queue_xmit+0x224/0x290
>
> which lock already depends on the new lock.
This turns out to be a genuine bug. The queue lock and xmit lock are
intentionally taken out of order. Two things are supposed to prevent
dead-locks from occuring:
1) When we hold the queue_lock we're supposed to only do try_lock on the
tx_lock.
2) We always drop the queue_lock after taking the tx_lock and before doing
anything else.
>
> the existing dependency chain (in reverse order) is:
>
> -> #1 (&dev->_xmit_lock){-+..}:
> [<c012e7b6>] lock_acquire+0x76/0xa0
> [<c0336241>] _spin_lock_bh+0x31/0x40
> [<c02d25a9>] dev_activate+0x69/0x120
This path obviously breaks assumption 1) and therefore can lead to ABBA
dead-locks.
I've looked at the history and there seems to be no reason for the lock
to be held at all in dev_watchdog_up. The lock appeared in day one and
even there it was unnecessary. In fact, people added __dev_watchdog_up
precisely in order to get around the tx lock there.
The function dev_watchdog_up is already serialised by rtnl_lock since
its only caller dev_activate is always called under it.
So here is a simple patch to remove the tx lock from dev_watchdog_up.
In 2.6.19 we can eliminate the unnecessary __dev_watchdog_up and
replace it with dev_watchdog_up.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the infrastructure for generic segmentation offload.
The idea is to tap into the potential savings of TSO without hardware
support by postponing the allocation of segmented skb's until just
before the entry point into the NIC driver.
The same structure can be used to support software IPv6 TSO, as well as
UFO and segmentation offload for other relevant protocols, e.g., DCCP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_deactivate function has bit-rotted since the introduction of
lockless drivers. In particular, the spin_unlock_wait call at the end
has no effect on the xmit routine of lockless drivers.
With a little bit of work, we can make it much more useful by providing
the guarantee that when it returns, no more calls to the xmit routine
of the underlying driver will be made.
The idea is simple. There are two entry points in to the xmit routine.
The first comes from dev_queue_xmit. That one is easily stopped by
using synchronize_rcu. This works because we set the qdisc to noop_qdisc
before the synchronize_rcu call. That in turn causes all subsequent
packets sent to dev_queue_xmit to be dropped. The synchronize_rcu call
also ensures all outstanding calls leave their critical section.
The other entry point is from qdisc_run. Since we now have a bit that
indicates whether it's running, all we have to do is to wait until the
bit is off.
I've removed the loop to wait for __LINK_STATE_SCHED to clear. This is
useless because netif_wake_queue can cause it to be set again. It is
also harmless because we've disarmed qdisc_run.
I've also removed the spin_unlock_wait on xmit_lock because its only
purpose of making sure that all outstanding xmit_lock holders have
exited is also given by dev_watchdog_down.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having two or more qdisc_run's contend against each other is bad because
it can induce packet reordering if the packets have to be requeued. It
appears that this is an unintended consequence of relinquinshing the queue
lock while transmitting. That in turn is needed for devices that spend a
lot of time in their transmit routine.
There are no advantages to be had as devices with queues are inherently
single-threaded (the loopback device is not but then it doesn't have a
queue).
Even if you were to add a queue to a parallel virtual device (e.g., bolt
a tbf filter in front of an ipip tunnel device), you would still want to
process the queue in sequence to ensure that the packets are ordered
correctly.
The solution here is to steal a bit from net_device to prevent this.
BTW, as qdisc_restart is no longer used by anyone as a module inside the
kernel (IIRC it used to with netif_wake_queue), I have not exported the
new __qdisc_run function.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various drivers use xmit_lock internally to synchronise with their
transmission routines. They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.
With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set. This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.
While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire. So
delaying or dropping the message is to be avoided as much as possible.
So the only alternative is to always set xmit_lock_owner. The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.
I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly. I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.
This is pretty much a straight text substitution except for a small
bug fix in winbond. It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission. This is
unsafe as an IRQ can potentially wake up the queue. So it is safer to
use netif_tx_disable.
The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential jiffy wraparound bug in the transmit watchdog
that is easily avoided by using time_after().
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the old __dev_put macro that is just a hold over from pre 2.6
kernel. And turn dev_hold into an inline instead of a macro.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
# grep -r 'netif_carrier_o[nf]' linux-2.6.12 | wc -l
246
# size vmlinux.org vmlinux.carrier
text data bss dec hex filename
4339634 1054414 259296 5653344 564360 vmlinux.org
4337710 1054414 259296 5651420 563bdc vmlinux.carrier
And this ain't an allyesconfig kernel!
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_create_dflt() is missing to destroy the newly allocated
default qdisc if the initialization fails resulting in leaks
of all kinds. The only caller in mainline which may trigger
this bug is sch_tbf.c in tbf_create_dflt_qdisc().
Note: qdisc_create_dflt() doesn't fulfill the official locking
requirements of qdisc_destroy() but since the qdisc could
never be seen by the outside world this doesn't matter
and it can stay as-is until the locking of pkt_sched
is cleaned up.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current call to __qdisc_dequeue_head leads to a branch
misprediction for every loop iteration, the fact that the
most common priority is 2 makes this even worse. This issue
has been brought up by Eric Dumazet <dada1@cosmosbay.com>
but unlike his solution which was to manually unroll the loop,
this approach preserves the possibility to increase the number
of bands at compile time.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds qdisc_alloc() to share code between qdisc_create()
and qdisc_create_dflt(). Hides the qdisc alignment behind
macros and makes use of them.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the skb trimming code which is not needed since we never
touch the skb upon failure. Removes unnecessary initializers,
and simplifies the code a bit.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
prio2list() returns the relevant sk_buff_head for the
band specified by the priority for a given skb.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to bugs in netem (fixed by later patches), it is possible to get qdisc
qlen to go negative. If this happens the CPU ends up spinning forever
in qdisc_run(). So add a BUG_ON() to trap it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers call netif_stop_queue() when detecting loss of
carrier. This leads to packets being queued up at the qdisc level for
an unbound period of time. In order to prevent this effect, the core
networking stack will now cease to queue packets for any device, that
is operationally down (i.e. the queue is flushed and disabled).
Signed-off-by: Tommy S. Christensen <tommy.christensen@tpack.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
