A newer board revision changed the type of ethernet phy.
Moreover, this generalizes the way that a phy gets switched
into fiber mode when autodetection is not available.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
We found a new chip setting that we need in order
to make the driver work more reliable.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip
on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting
ei_status.word16.
The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in
8-bit mode -- ensure this too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
since the au1000 driver already selects the CRC32 routines, simply replace
the internal ether_crc() implementation with the semantically equivalent
one from <linux/crc32.h>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: Stephe Hemminger <shemminger@osdl.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
It is more efficient not to write the status ring from the
processor and just read the active portion.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Gcc isn't smart enough to know that it can do a modulo
operation with power of 2 constant by doing a mask.
So add macro to do it for us.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Mask for transmit ring status was picking up bits from the
unused sync ring. They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This is a backout of earlier patch.
The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Taking the cpu hotplug semaphore in a normal events workqueue
is unsafe because other tasks can wait for any workqueues with
it hold. This results in a deadlock.
Move the DBS timer into its own work queue which is not
affected by other work queue flushes to avoid this.
Has been acked by Venkatesh.
Cc: venkatesh.pallipadi@intel.com
Cc: cpufreq@lists.linux.org.uk
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: Do not overwrite makefile as anohter user
kbuild: drivers/video/logo/ - fix ident glitch
kbuild: fix gen_initramfs_list.sh
kbuild modpost - relax driver data name
kbuild: removing .tmp_versions considered harmful
kbuild: fix modpost segfault for 64bit mipsel kernel
Use NULL instead of 0 for a null pointer value (sparse warning):
drivers/net/irda/irda-usb.c:1781:30: warning: Using plain integer as NULL pointer
Also, correct timeout argument to use milliseconds instead of jiffies.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the support of attribute groups in class_device's to allow
groups to be created as part of the registration process. This allows
network device's to avoid race between registration and creating
groups.
Note that unlike attributes that are a property of the class object,
the groups are a property of the class_device object. This is done
because there are different types of network devices (wireless for
example).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/rtc/rtc-sa1100.c: In function `sa1100_rtc_proc':
drivers/rtc/rtc-sa1100.c:298: warning: unsigned int format, long unsigned int arg (arg 3)
and arrange for sa1100_rtc_open() to pass the devid to free_irq()
rather than NULL.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the conditions under which we poke at the APHY registers in
bcm43xx_phy_initg() to avoid a machine check on chips where they don't
exist.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem here is that the bcm34xx driver and the ieee80211
stack do not agree on what channels are possible for 802.11a.
The ieee80211 stack only wants channels between 34 and 165, while
the bcm43xx driver accepts anything from 0 to 200. I made the
bcm43xx driver comply with the ieee80211 stack expectations, by
using the proper constants.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
[mb]: Reduce stack usage by kzalloc-ing ieee80211_geo
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for valid MAC address in SPROM fields instead of relying on
PHY type while setting the MAC address in the networking subsystem,
as some devices have multiple PHYs.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a crash when
iwconfig ethX mode foo
is done before
ifconfig ethX up
or after
ifconfig ethX down
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: Use the ibm,pa-features property if available
powerpc: Fix incorrect might_sleep in __get_user/__put_user on kernel addresses
[PATCH] ppc32 CPM_UART: fixes and improvements
[PATCH] ppc32 CPM_UART: Fixed break send on SCC
[PATCH] powerpc/kprobes: fix singlestep out-of-line
[PATCH] powerpc/pseries: avoid crash in PCI code if mem system not up
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3490/1: i.MX: move uart resources to board files
[ARM] 3488/1: make icedcc_putc do the right thing
[ARM] 3487/1: IXP4xx: Support non-PCI systems
[ARM] 3486/1: Mark memory as clobbered by the ARM _syscallX() macros
Rather than having every driver duplicate the set_ios debugging,
provide a single version in mmc.c which can be expanded as we
add additional functionality.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch moves the i.MX uart resources and the gpio pin setup to the
board files. This allows the boards to decide how many internal uarts
are connected to the outside world and whether they use rts/cts or
not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mmc_request_done should be called at the end of handling a request, not
between the data and initial command parts of the request.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently loading the ioc3 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Address the issue of EDAC/BIOS coexistence for the e752x chip-sets.
We have found a problem where the BIOS will start the system with the error
registers (dev0:fun1) hidden and assuming it has exclusive access to them.
The edac driver violates this assumption.
The workaround this patch offers is to honor the hidden-ness as an
indication that it is not safe to use those registers.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the lpfc driver to revision 8.1.6, which includes
the following changes:
- Fix data corruption in SCSI BUS reset path, due to reusing
the same request structure for each target.
- Change version number to 8.1.6
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a bug fix for mptspi driver, where after a host reset or
resume, we revalidate the negotiation parameters for all devices.
This bug was introduced when the driver was ported to use the spi
transport layer.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A number of small issues are fixed, and added the header file, missed from the
original series. With this, driver should be pretty stable as tested among
both platform-device-driven and "old way" boards. Also added missing GPL
statement , and updated year field on existing ones to reflect
code update.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SCC uart sends a break sequence each time it is stopped with the
CPM_CR_STOP_TX command. That means that each time an application closes the
serial device, a break is transmitted. To fix this, graceful tx stop is
issued for SCC.
Signed-off-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes the issues with multiple irqs.
I am resending based on feedback. I decoupled the dma mask for
consistent memory and fixed leak with multiple irq in error path.
Thanks to Manfred for catching the spin lock problem.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Fixes Rhine I cards disclosing fragments of previously transmitted frames
in new transmissions.
Before transmission, any socket buffer (skb) shorter than the ethernet
minimum length of 60 bytes was zero-padded. On Rhine I cards the data can
later be copied into an aligned transmission buffer without copying this
padding. This resulted in the transmission of the frame with the extra
bytes beyond the provided content leaking the previous contents of this
buffer on to the network.
Now zero-padding is repeated in the local aligned buffer if one is used.
Following a suggestion from the via-rhine maintainer, no attempt is made
here to avoid the duplicated effort of padding the skb if it is known that
an aligned buffer will definitely be used. This is to make the change
"obviously correct" and allow it to be applied to a stable kernel if
necessary. There is no change to the flow of control and the changes are
only to the Rhine I code path.
The patch has run on an in-service Rhine-I host without incident. Frames
shorter than 60 bytes are now correctly zero-padded when captured on a
separate host. I see no unusual stats reported by ifconfig, and no unusual
log messages.
Signed-off-by: Craig Brind <craigbrind@gmail.com>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Sat, Mar 11, Olaf Hering wrote:
> Why is the /sys/class/net/eth0/device symlink not created for the
> mv643xx_eth driver? Does this work for other platform device drivers?
> Seems to work for the ps2 keyboard at least.
The SET_NETDEV_DEV has to be done before a call to register_netdev. With
the new patch below, the device symlink for the platform device was
created. Unfortunately, after the 4 ls commands, the network connection
died. No idea if the box crashed or if something else broke, lost remote
access.
Provide sysfs 'device' in /class/net/ethN Also, set module owner field,
like pcnet32 driver does.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's no reason for the PXAMCI debug code to print so many lines - it
causes the kernel buffer to overflow when trying to debug this driver.
Remove some debug messages which are duplicated by core code, and
combine other messages, resulting in fewer characters written to the
kernel log.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hi,
The following patch contains fix related to init and shutdown of adapter
as per user guide. The list of changes include
1. shutdown gracefully.
2. Need to mask/unmask interrupts in ISR required fro Xframe-E
3. Tx FIFO should be enabled after WRR calender programming
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch contains additional statistics counters added to s2io driver
these statistics are very much usefull in debugging the driver.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch contains some of the bug fixes done for S2io driver.
Following are the brief description of changes
1. Continuing with initialization if we get minimum required MSI-X vectors
2. fix for ethtool online link test fails
3. make wait_for_cmd_complete generic for all command status registers
4. Print "Device is on PCI-E bus" for Xframe-E card
5. CX4 requires additional delay after sw_reset, and requires higher value for igp
6. Fixed panic due to non-TCP and/or LLC/SNAP traffic in case of lro
7. remove legacy code for old transponder
8. SPECIAL_REG_WRITE made to use 32-bit writes irrespective of system type
9. handle link interrupt as per user guide for Xframe II
10. Wait till all interrupts hndled
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
This patch contains the modification and bug fixes with respect to
input parameters and outupt dmesages. following is brief description
of the changes.
1. Set default values for rx_ring_sz[0..7] and tx_fifo_len[0..7]
2. verify few basic load parameters
3. read product description from VPD
4. clean up of dmesg when driver is loaded
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
This patch contains all the changes that were done to improve
performance of s2io driver. one line description of the changes
are
1. For Non NAPI case the rx interrupt handler is being called
unconditionally
2. code optimization and adding prefetch skb->data
3. Remove modulo operations in fast path
4. Enable Group Reads and set backoff interval to 0x1000
5. correct PIC_CNTL_SHARED_SPLITS macro definition, and reduce
pause parameter
6. Corrected logic of identifying rx buffer level in rx_buffer_level()
7. fix DMA map and unmap done with different sizes in 1-buf mode
8. Removed forcible disabling of ERO
9. Send up the packets with transfer code = 0x5
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Always send a stop command at the end of a data transfer. If we avoid
sending the stop command, some cards remain in data transfer mode, and
refuse to accept further read/write commands.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CSD contains a "read2write factor" which determines the multiplier to
be applied to the read timeout to obtain the write timeout. We were
ignoring this parameter, resulting in the possibility for writes being
timed out too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
x86 SMP breaks as a result of the previous change, we have no real
option other than to add locking to the 8250 console write function.
If an oops is in progress, try to acquire the lock. If we fail to
do so, continue anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: tidy up white space in a few files
IB/ipath: fix label name in interrupt handler
IB/ipath: improve sparse annotation
IB/ipath: simplify IB timer usage
IB/ipath: simplify RC send posting
IB/ipath: prevent hardware from being accessed during reset
IB/ipath: fix verbs registration
IB/ipath: change handling of PIO buffers
IB/ipath: iterate over correct number of ports during reset
IB/ipath: set up 32-bit DMA mask if 64-bit setup fails
IB/ipath: fix race with exposing reset file
IB/mthca: Fix offset in query_gid method
Fix genrtc's read() routine for 64-bit platforms. Current gen_rtc_read()
stores 64bit integer and returns 8 even if an user tried to read a 32bit
integer.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make rtc-dev work well on 64-bit platforms with 32-bit userland. On those
platforms, users might try to read 32-bit integer value. This patch make
rtc-dev's read() work well for both "int" and "long" size. This tweak is came
from genrtc driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out by Paulo Marques <pmarques@grupopie.com> MAX_IPD_TIME is by
a factor of ten too small. Since this means that we allow ten times more
IPDs in the intended time frame this could result in a cpu check stop of a
physical cpu.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently loading the ioc3 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When retrying a failed BIO_RW_BARRIER request, we need to keep the reference
in ->nr_pending over the whole retry. Currently, we only hold the reference
if the failed request is the *last* one to finish - which is silly, because it
would normally be the first to finish.
So move the rdev_dec_pending call up into the didn't-fail branch. As the rdev
isn't used in the later code, calling rdev_dec_pending earlier doesn't hurt.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the test for 'do barrier work' down a bit so that if the first write to a
raid1 is a BIO_RW_BARRIER write, the checking done by superblock writes will
cause the right thing to happen.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because that is what you get if a BIO_RW_BARRIER isn't supported!
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to hold a reference to rdevs while reading and writing to attempt to
correct read errors. This reference must be taken under an rcu lock.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should add to the counter for the rdev *after* checking if the rdev is
NULL!!!
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Names that are the opposite of their intended meanings are not so helpful.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The reset code now turns off the PRESENT flag during a reset, so that
other code won't attempt to access a device that's in mid-reset.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remember when the verbs layer unregisters from the lower-level code.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different ipath hardware types have different numbers of buffers
available, so we decide on the counts ourselves unless we are specifically
overridden with a module parameter.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some systems do not set up 64-bit maps on systems with 2GB or less of
memory installed, so we have to fall back to trying a 32-bit setup.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We were accidentally exposing the "reset" sysfs file more than once
per device.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
GuidInfo records have 8 byte GUIDs in them, so an index should be
multiplied by 8 to get an offset. mthca_query_gid() was incorrectly
multiplying by 16.
Noticed by Leonid Keller <leonid@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Update version and reldate
[TG3]: Fix bug in nvram write
[TG3]: Add reset_phy parameter to chip reset functions
[TG3]: Reset chip when changing MAC address
[TG3]: Add phy workaround
[TG3]: Call netif_carrier_off() during phy reset
[IPV6]: Fix race in route selection.
[XFRM]: fix incorrect xfrm_policy_afinfo_lock use
[XFRM]: fix incorrect xfrm_state_afinfo_lock use
[TCP]: Fix unlikely usage in tcp_transmit_skb()
[XFRM]: fix softirq-unsafe xfrm typemap->lock use
[IPSEC]: Fix IP ID selection
[NET]: use hlist_unhashed()
[IPV4]: inet_init() -> fs_initcall
[NETLINK]: cleanup unused macro in net/netlink/af_netlink.c
[PKT_SCHED] netem: fix loss
[X25]: fix for spinlock recurse and spinlock lockup with timer handler
* git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: make EVIOCGSND return meaningful data
Input: ressurect EVIOCGREP and EVIOCSREP
Input: psmouse - fix new device detection logic
Input: move input_device_id to mod_devicetable.h
Input: allow using several chords for braille
Input: allow passing NULL to input_free_device()
Input: spitzkbd - fix the reversed Address and Calender keys
Input: ads7846 - improve filtering for thumb press accuracy
Input: ads7846 - report 0 pressure value along with pen up event
Input: ads7846 - handle IRQs that were latched during disabled IRQs
Input: ads7846 - miscellaneous fixes
Input: ads7846 - use msleep() instead of udelay() in suspend
Input: ads7846 - debouncing and rudimentary sample filtering
Input: ads7846 - power down ADC a bit later
Input: ads7846 - add pen_down sysfs attribute
Input: wistron - add support for Fujitsu N3510
Input: wistron - add signature for Amilo M7400
* git://git.kernel.org/pub/scm/linux/kernel/git/perex/alsa: (22 commits)
[ALSA] via82xx - Use DXS_SRC as default for VIA8235/8237/8251 chips
[ALSA] hda-codec - Add model entry for ASUS Z62F
[ALSA] PCMCIA sound devices shouldn't depend on ISA
[ALSA] hda-codec - Fix capture from line-in on VAIO SZ/FE laptops
[ALSA] Fix Oops at rmmod with CONFIG_SND_VERBOSE_PROCFS=n
[ALSA] PCM core - introduce CONFIG_SND_PCM_XRUN_DEBUG
[ALSA] adding __devinitdata to pci_device_id
[ALSA] add __devinitdata to all pci_device_id
[ALSA] hda-codec - Add codec id for AD1988B codec chip
[ALSA] hda-codec - Add model entry for ASUS M9 laptop
[ALSA] pcxhr - Fix a compiler warning on 64bit architectures
[ALSA] via82xx: tweak VT8251 workaround
[ALSA] intel8x0 - Disable ALI5455 SPDIF-input
[ALSA] via82xx: add support for VIA VT8251 (AC'97)
[ALSA] Fix typos and add information about Jack support to Audiophile-Usb.txt
[ALSA] Fix double free in error path of miro driver
[ALSA] hda-codec - Add entry for Epox EP-5LDA+ GLi
[ALSA] sound/pci/: remove duplicate #include's
[ALSA] hda-codec - Use model 'hp' for all HP laptops with AD1981HD
[ALSA] continue on IS_ERR from platform device registration
...
Jan Engelhardt <jengelh@linux01.gwdg.de> wrote:
while compiling 2.6.17-rc2 with allyesconfig, this showed up:
...
LOGO drivers/video/logo/logo_superh_clut224.c
CC drivers/video/logo/logo_linux_mono.o
...
A tab had sneaked in. Convert it to a few spaces.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Patch from Pavel Pisa
The clock starting imxmci_start_clock() function contains hardware
issue workaround, which repeats start attempt, if SDHC does not react on
the first trial. But the second start attempt can be taken even, if the
first succeed and test code misses time limited clock running phase
due to delay caused by schedule to other task or some another device
interrupt. This change enables to detect such situation.
The performance is not issue, because usually at full clock rate
only about six loops in delay cycle are needed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Markus Gutschke
In order to prevent gcc from making incorrect optimizations, all asm()
statements that define system calls should report memory as
clobbered. Recent versions of the headers for i386 have been changed
accordingly, but the ARM headers are still defective.
This patch fixes the bug tracked at
http://bugzilla.kernel.org/show_bug.cgi?id=6205
Signed-off-by: Markus Gutschke <markus@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A bug report from Gerd Hoffmann has highlighted that unconditionally
enabling the transmit interrupt at the end of console writes is very
bad.
In Gerd's case, it causes the test for buggy UARTs to give false
positives, incorrectly identifying ports as buggy when they are not.
Moreover, if we unconditionally enable the interrupt, and the port
is sharing it's interrupt with other ports, there is the very real
possibility that we'll cause an interrupt storm. (Not all ports use
OUT2 as an interrupt mask.)
Hence, revert part of f91a3715db and
all of f5968b37b3 until a better solution
can be found.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Alchemy SoC uart have got a non-standard divisor register that needs some
special handling.
This patch adds divisor read/write functions with test and special
handling for Alchemy internal uart.
Signed-off-by: Jon Anders Haugum <jonah@omegav.ntnu.no>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've noticed that the 8250/Au1x00 driver (drivers/serial/8250_au1x00.c)
doesn't claim UART memory ranges and uses wrong (KSEG1-based) UART
addresses instead of the physical ones.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The locking for the uart_port is over complicated, and can be
simplified if we introduce a flag to indicate that a port is "dead"
and will be removed.
This also helps the validator because it removes a case of non-nested
unlock ordering.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix bug in nvram write function. If the starting nvram address offset
happens to be the last dword of the page, the NVRAM_CMD_LAST bit will
not get set in the existing code. This patch fixes the bug by changing
the "else if" to "if" so that the last dword condition always gets
checked.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reset_phy parameter to tg3_reset_hw() and tg3_init_hw(). With
the full chip reset during MAC address change, the automatic PHY reset
during chip reset will cause a link down and bonding will not work
properly as a result. With this reset_phy parameter, we can do a chip
reset without link down when changing MAC address or MTU.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the full chip reset when changing MAC address if ASF is enabled.
ASF sometimes uses a different MAC address than the driver. Without
the reset, the ASF MAC address may be overwritten when the driver's
MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some PHY workaround code to reduce jitter on some PHYs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_carrier_off() call during tg3_phy_reset(). This is needed
to properly track the netif_carrier state in cases where we do a
PHY reset with interrupts disabled. The SerDes code will not run
properly if the netif_carrier state is wrong.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let people enable the advansys driver on x86-32, even though it's broken
on other architectures due to missing DMA mapping infrastructure.
It's used by Jeffrey Phillips Freeman <jeffreyfreeman@syncleus.com> and
possibly others.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While writing to an event device allows to set repeat rate for an
individual input device there is no way to retrieve current settings
so we need to ressurect EVIOCGREP. Also ressurect EVIOCSREP so we
have a symmetrical interface.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add help text in Kconfig
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Generate new sysfs-attribute 'uid' that contains an device specific unique
identifier. This can be used to identity multiple ALIASES of the same
physical device (PAV). In addition the sysfs-attributes 'vendor' (containing
the manufacturer of the device) and 'alias' (identify alias or base device) is
added. This is first part of PAV support in LPAR (also valid on zVM).
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In case of an instruction processing damage (IPD) machine check in kernel mode
the resulting action is always to stop the kernel. This is not necessarily
the best solution since a retry of the failing instruction might succeed. Add
logic to retry the instruction if no more than 30 instruction processing
damage checks occured in the last 5 minutes.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added some changes that where proposed by Andrew Morton. Added 3592 device
type.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_SLAB_DEBUG=y networking over qeth doesn't work. The problem is
that the qib structure embedded in the qeth_irq structure needs an alignment
of 256 but kmalloc only guarantees an alignment of 8. When using SLAB
debugging the alignment of qeth_irq is not sufficient for the embedded qib
structure which causes all users of qdio (qeth and zfcp) to stop working.
Allocate qeth_irq structure with __get_free_page. That wastes a small amount
of memory (~2500 bytes) per online adapter.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dasd state machine is not designed to enable an unformatted device, since
'unformatted' is a final state. The BIODASDENABLE ioctl calls
dasd_enable_device() which never returns if the device is in this special
state. Return -EPERM in dasd_increase_state for unformatted devices to make
dasd_enable_device terminate. Note: To get such an unformatted device online
it has to be re-analyzed. This means that the device needs to be disabled
prior to re-enablement.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid memory allocation with GFP_KERNEL in qdio_establish/qdio_shutdown. Use
memory pool instead. (Otherwise this can lead to an I/O stall where qdio
waits for a free page and zfcp waits for end of error recovery in low memory
situations.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Interrupts can stay disabled if an error occurred in _chp_add(). Use
spin_unlock_irq on the error paths to reenable interrupts.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a race condition in the I/O termination logic. The race can cause I/O to
a dasd device to fail with no retry left after turning one channel path to the
device off and on multiple times.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this fixes coverity id #489.
Since the last element in the array is always ARRAY_SIZE-1 we have to check
for ipcnum >= ARRAY_SIZE()
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If compiled into the kernel, parport_register_driver() is called before the
parport driver has been initalised.
This means that it is expected that tp_count is 0 after the
parport_register_driver() call() - tipar's attach function will not be
called until later during bootup.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add new SA_PROBEIRQ which suppresses the new sharing-mismatch warning.
Some drivers like to use request_irq() to find an unused interrupt slot.
- Use it in i82365.c
- Kill unused SA_PROBE.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current address translation methods can produce wrong results, because
virt_to_bus and vice versa may not produce correct offsets on dma-allocated
memory. The right way is, while tracking both phys and virt address of the
window that has been allocated for boffer descriptors, and use those
numbers to compute the offset and make translation properly.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is intended to make the driver code more generic and flexible,
to get rid of board-specific layouts within driver, and generic rehaul,
yet keeping compatibility with the existing stuff utilizing it, being
compatible with legacy behavior (but with complaints that legacy mode
used).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some people report that we die on some Macs when we are expecting to
catch machine checks after poking at some random I/O address. I'd seen
it happen on my dual G4 with serial ports until we fixed those to use
OF, but now other users are reporting it with i8042.
This expands the use of check_legacy_ioport() to avoid that situation
even on 32-bit kernels.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] update sn2 defconfig
[IA64] Add mca recovery failure messages
[IA64-SGI] fix SGI Altix tioce_reserve_m32() bug
[IA64] enable dumps to capture second page of kernel stack
[IA64-SGI] - Reduce overhead of reading sn_topology
[IA64-SGI] - Fix discover of nearest cpu node to IO node
[IA64] IOC4 config option ordering
[IA64] Setup an IA64 specific reclaim distance
[IA64] eliminate compile time warnings
[IA64] eliminate compile time warnings
[IA64-SGI] SN SAL call to inject memory errors
[IA64] - Fix MAX_PXM_DOMAINS for systems with > 256 nodes
[IA64] Remove unused variable in sn_sal.h
[IA64] Remove redundant NULL checks before kfree
[IA64] wire up compat_sys_adjtimex()
Fix the driver to return SUCCESS if the firmware or driver doesn't
have a command to abort, i.e., it's already been returned. Without
this patch, error recovery will take the target offline as it tries
harder and harder to get the driver to return the command it no longer
has.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] PCI quirk: VIA IRQ fixup should only run for VIA southbridges
[PATCH] PCI: fix potential resource leak in drivers/pci/msi.c
[PATCH] PCI: Documentation: no more device ids
[PATCH] PCI: fix via irq SATA patch
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
[PATCH] USB: ftdi_sio: add support for ASK RDR 400 series card reader
[PATCH] USB: ftdi_sio: Adds support for iPlus device.
[PATCH] USB: ftdi_sio vendor code for RR-CirKits LocoBuffer USB
[PATCH] USB: Use new PCI_CLASS_SERIAL_USB_* defines
[PATCH] USB: net2280: set driver data before it is used
[PATCH] USB: net2280: check for shared IRQs
[PATCH] USB: net2280: send 0-length packets for ep0
[PATCH] USB: net2280: Handle STALLs for 0-length control-IN requests
[PATCH] USB: storage: atmel unusual dev update
[PATCH] USB: Storage: unusual devs update
[PATCH] USB: add new iTegno usb CDMA 1x card support for pl2303
[PATCH] USB: Resource leak fix for whiteheat driver
Alan Cox pointed out that the VIA 'IRQ fixup' was erroneously running
on my system which has no VIA southbridge (but I do have a VIA IEEE
1394 device).
This should address that. I also changed "Via IRQ" to "VIA IRQ"
(initially I read Via as a capitalized via (by way/means of).
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The coverity checker spotted (as entry #599) that we might leak `entry' in
drivers/pci/msi.c::msix_capability_init()
This patch should take care of that.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When abort failed, the driver gets reset handleer called. In the reset
handler, driver calls 'scsi_done()' callback for same SCSI command packet
(struct scsi_cmnd) multiple times if there are multiple SCSI command packet
in the pend_list. More over, if there are entry in the pend_lsit with
IOCTL packet associated, the driver returns it to wrong free_list so that,
in turn, the driver could end up with 'NULL pointer dereference..' during
I/O command building with incorrect resource.
Also, the patch contains several minor/cosmetic changes besides this.
Signed-off-by: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fix for stack overflow in EventDescriptionStr, (a function
for debuging firmware events). We allocated 50 bytes on local stack
for buff[], however there are places in the code where we've attempted
copying in greater than 50 bytes into buff[].
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some versions of the IBM 2104-DU3 disk enclosure
have been observed to hang Inquiries to non zero
LUNs to the SES device. This device only has LUN 0,
so this patch adds it to the BLIST to prevent scsi
core from scanning beyond LUN 0.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some pioneer DVDs are apparently returning odd "not ready" status
codes that the mid-layer doesn't recognise and so passes back to the
user as errors.
This patch overhauls our not-ready handling and adds transparent retries for:
format in progress
rebuild in progress
recalculation in progress
operation in progress
Long write in progress
self test in progress
The Pioneer was actually returning "long write in progress"
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for an ASK RDR 400 series contactless card
reader <http://www.ask.fr/uk/products_and_services/terminals.html> to
the ftdi_sio driver's device ID table. The product ID was supplied by
Adriano Couto on the ftdi-usb-sio-devel list.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support in ftdi_sio usbserial driver for USB modems sold by
Plus GSM Company in Poland.
Signed-off-by: Luiz Fernando Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds recognition of the RR-CirKits LocoBuffer USB
to the existing FTDI driver. http://www.rr-cirkits.com
Signed-off-by: Nathan Bronson <ngb@sns-usa.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could use the recently added PCI_CLASS_SERIAL_USB_UHCI,
PCI_CLASS_SERIAL_USB_OHCI and PCI_CLASS_SERIAL_USB_EHCI defines in
more places, for slightly shorter and clearer code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as671) fixes a bug in the error pathway for the net2280
probe routine. A failure during probe will cause the driver to call
pci_get_drvdata before the corresponding pci_set_drvdata has been set.
The patch also does a kzalloc conversion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as670) adds a check for whether a shared IRQ was actually
generated by the net2280 device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as669) fixes a bug in the net2280 driver. Now it will
properly send zero-length packets on ep0 until the control status stage
occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as668) fixes a typo in net2280. The handler for 0-length
control-IN requests should check that the endpoint _isn't_ halted before
sending a 0-length packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally submitted by Olivier Blondeau <zeitoun@gmail.com>, with re-diffing
by me. Adds a new atmel unusual_dev entry.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
This patch removes the Protocol portion of the Iomega Click! device as it's not
needed. Not-needed message reported by Kenneth Crudup <kenny@panix.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new iTegno usb CDMA 1x card (usbid '0eba:2080') support to pl2303 driver
Signed-off-by: Wang Jun <wangjun1974@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We may return from drivers/usb/serial/whiteheat.c::whiteheat_attach()
without freeing `result' if we leave via the no_firmware: label.
Spotted by the coverity checker as #670
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call. It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).
This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the nic initialization. If the nic was in low power
mode, it brings it back to normal power. Also, it utilizes a new
hardware reset during the init.
I am resending based on feedback, I corrected the register size mapping
and delay after posted write.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.
The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
For coping with bad keyboards, permit to type a braille pattern by
pressing several chords. By default, only one chord is needed.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Providing more accurate coordinates for thumb press requires additional
steps in the filtering logic:
- Ignore samples found invalid by the debouncing logic, or the ones that
have out of bound pressure value.
- Add a parameter to repeat debouncing, so that more then two consecutive
good readings are required for a valid sample.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
X touchscreen drivers that don't interpret the designated pen up message
assume a pen up event from a pressure value 0. For these we generate a
pressure 0 message along with the pen up message.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix resource leak in
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c::ahc_linux_pci_dev_probe()
Found by the coverity checker (#668)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
mptbase.h
bump version number to 3.03.09
remove unneeded flags
define workq and remove old fc specific locks
mptbase.c
initialize new lock and don't initialize two removed locks
mptscsih.c
when firmware reports target is no longer there, return
DID_REQUEUE for fc hosts so that i/o doesn't get killed until
the transport has an opportunity to manage the loss via its
dev loss timer
when the "eh_abort" routine is called, check to see if the
driver has the command or not before looking to see if a reset
is pending. James Smart and I talked about this and believe
that the API for this routine is: if driver doesn't have
command, return SUCCESS. This change helps prevent a target
from being taken offline. SUCCESS is returned because it's
likely that the command completed after error recovery timed
it out but before it could be aborted.
provide a routine to queue work to newly created workq, and
use it.
remove "ioc" from mptscsih_abort() it was only used one time.
the other references were via hd->ioc, so I just moved it....
net change in references to ioc via hd->ioc is zero
move hd->resetPending test and hd->timeouts increment to after
the test for whether the command to be aborted remains known
to the driver
Make certain that the workq exists before queuing work to it.
mptfc.c
no longer need to lock rport data structures as I was able to
single thread the code! I fixed up the debug code to
eliminate compilation messages due to type mismatch in the
printk. Got rid of some no longer needed rport flags.
Initialize and destroy the workq used for the rescan work.
simplify the logic regarding the increment of
fc_rescan_work_count. use post increment and test for zero
vs. pre increment and test for one; eliminate work_count
variable: queue_work can be called with the work_lock held as
it doesn't sleep
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch handles case where raid hidden components
are not being removed when power turned off to device
attached to expander, as well as the case of
exposing raid components when power is turned back on
to devices attached to an expander. (This is a repost
of this patch, with mptsas_is_end_device declared
further up in the code.)
This patch contains some other miscellaneous bug fix's.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
airo cards with firmware versions of 5.30.17 and higher support WPA.
This patch recognizes WPA-capable firmware versions and adds support for
retrieving the WPA and RSN information elements from the card's scan
results. The JOB and FLAG fields are now independent, since there was
no space left in the FLAG field for FLAG_WPA_CAPABLE.
Signed-off-by: matthieu castet <castet.matthieu@free.fr>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ipw2200 scan completion event feature will cause a potential event
race condition in wpa_supplicant. The patch fixes this problem by move the
ipw_disassociate() to the IW_AUTH_WPA_ENABLED event handling code.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->last_noise is not used with the exponential averaging algorithm
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makefile both IPW2200_RADIOTAP and IPW2200_PROMISCUOUS depend on
IPW2200_MONITOR. Let IPW2200_PROMISCUOUS select IPW2200_RADIOTAP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added version string fields so the version string indicates what is
configured (ie, you'll see 1.1.1kpmd if you are using a GIT snapshot
(Kernel.. previously -git), promiscuous (p), monitor (m), debug (d) build.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch, a new promiscuous mode is enabled. If the module is loaded
with the rtap_iface=1 module parameter, two interfaces will be created
(instead of just one).
The second interface is prefixed 'rtap' and provides received 802.11 frames
on the current channel to user space in a radiotap header format.
Example usage:
% modprobe ipw2200 rtap_iface=1
% iwconfig eth1 essid MyNetwork
% dhcpcd eth1
% tcpdump -i rtap0
If you do not specify 'rtap_iface=1' then the rtap interface will
not be created and you will need to turn it on via:
% echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
You can filter out what type of information is passed to user space via
the rtap_filter sysfs entry. Currently you can tell the driver to
transmit just the headers (which will provide the RADIOTAP and IEEE
802.11 header but not the payload), to filter based on frame control
type (Management, Control, or Data), and whether to report transmitted
frames, received frames, or both.
The transmit frame reporting is based on a patch by Stefan Rompf.
Filters can be get and set via a sysfs interface. For example, set the
filter to only send headers (0x7), don't report Tx'd frames (0x10), and
don't report data frames (0x100):
% echo 0x117 > /sys/bus/pci/drivers/ipw2200/*/rtap_filter
All your packets are belong to us:
% tethereal -n -i rtap0
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects endian issues with the v3.0 fw image format.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch make ipw2200 generate the scan event every time a scan has
completed, so that user space know when to get fresh results.
Dan Williams would like to go towards this model in Network Manager
rather than having to poll.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch works with the ieee80211 stack to set the correct QoS bit to the
ipw2200 card. It fixed the TX failure problem for using WPA with QoS.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces sliding averaging by exponential averaging for
reporting the wireless statistics for signal and noise level for ipw2200.
See details from: http://www.ces.clemson.edu/linux/ipw2200_averages.shtml
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make all Orinoco PCI drivers (orinoco_pci, orinoco_plx, orinoco_tmd and
orinoco_nortel) as similar as possible. Use the best implementation of
error handling, the best error messages, the best comments.
Put common code to orinoco_pci.h. For now, it's suspend and resume
functions and function for registering the network device.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy PCI suspend/resume functions from orinoco_pci.c.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to identify the card before possible allocation problems,
so that the user at least can report the firmware version that fails.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After several days of operation of Netgear MA311 card, the card becomes
to seek improperly and needs reset. This patch tries to reset the card
when this situation occurs.
Mar 9 06:45:16 berkeley kernel: wlan0: Error -5 writing packet to BAP
Mar 9 06:45:16 berkeley kernel: hermes @ f992a000: BAP0 offset error: reg=0x4044 id=0x128 offset=0x44
Mar 9 06:45:16 berkeley kernel: wlan0: Error -5 writing packet to BAP
Mar 9 06:45:16 berkeley kernel: hermes @ f992a000: BAP0 offset error: reg=0x4044 id=0x128 offset=0x44
(etc.)
A more detailed description of the problem can be found at
https://bugzilla.novell.com/show_bug.cgi?id=154773
The same problem with different card is reported at
http://sourceforge.net/mailarchive/message.php?msg_id=14597046
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use skb_pull() to strip the addresses from the original packet. Don't
strip protocol bytes.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The result of orinoco_xmit() can be OK, dropped packet and busy
transmitter. Rename labels accordingly. Increment stats->tx_errors in
one place. Increment stats->tx_dropped - nobody is doing it for us.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hermes_bap_pwrite() supports odd-sized packets now. There is no
minimal packet size for 802.11. Also, hermes_bap_pwrite() supports
odd-sized packets now. This removes all reasons to pad the Tx data.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new function can write an odd number of bytes, thus making padding
unnecessary.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't ever return -errno from orinoco_xmit() - the network layer doesn't
expect it.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing Tx exception, only read data until addr1. Rename
hermes_tx_descriptor_802_11 to hermes_txexc_data since it's only used to
Tx exceptions. Reuse existing hermes_tx_descriptor structure. Remove
fields after addr1 - they are not read from the card.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sparse is much better at finding endianess issues than such visual cues.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCMCIA drivers would never be loaded if the CIS were wrong.
No other PCMCIA drivers validate CIS.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes PIO mode on the softmac bcm43xx
driver. (A dscape patch will follow).
It mainly fixes endianess issues.
This patch is tested on PowerPC32 and i386.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was doing arithmetics on a little-endian value.
Reported by Stelios Koroneos <stelios@stelioscellar.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MMC layer gives us two parts for the timeout calculation - a fixed
timeout in nanoseconds, and a card clock-speed dependent part.
The PXA MMC hardware allows for a timeout based on the fixed host clock
speed only. This resulted in some cards being given a short timeout,
and therefore failing to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] MAINTAINERS
[PARISC] Make ioremap default to _nocache
[PARISC] Add new entries to the syscall table
[PARISC] Further work for multiple page sizes
[PARISC] Fix up hil_kbd.c mismerge
[PARISC] defconfig updates
[PARISC] Document that we tolerate "Relaxed Ordering"
[PARISC] Misc. janitorial work
[PARISC] EISA regions must be mapped NO_CACHE
[PARISC] OSS ad1889: Match register names with ALSA driver
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6:
[PATCH] pcmcia/pcmcia_resource.c: fix crash when using Cardbus cards
[PATCH] vrc4171: update config
[PATCH] pcmcia: fix oops in static mapping case
[PATCH] pcmcia: remove unneeded forward declarations
[PATCH] pcmcia: do not set dev_node to NULL too early
[PATCH] pcmcia: fix comment for pcmcia_load_firmware
[PATCH] pcmcia: unload second device first
[PATCH] pcmcia: add new ID to pcnet_cs
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
powerpc: Fix define_machine so machine_is() works from modules
powerpc/ppc: export strncasecmp
[PATCH] powerpc: fix oops in alsa powermac driver
[PATCH] powerpc: update {g5,iseries,pseries}_defconfigs
[PATCH] ppc: Fix powersave code on arch/ppc
[PATCH] powerpc/cell: remove BUILD_BUG_ON and add sys_tee to spu_syscall_table
[PATCH] powermac: Fix i2c on keywest based chips
[PATCH] powerpc: Lower threshold for DART enablement to 1GB
[PATCH] powerpc: IOMMU support for honoring dma_mask
This patch contains the following possible cleanups:
- make the following needlessly global function static:
- drm_bufs.c: drm_addbufs_fb()
- remove the following unused EXPORT_SYMBOL's:
- drm_agpsupport.c: drm_agp_bind_memory
- drm_bufs.c: drm_rmmap_locked
- drm_bufs.c: drm_rmmap
- drm_stub.c: drm_get_dev
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Airlie <airlied@linux.ie>
I recently found that not all BIOS manufacturers are using the specified
generic PNP id in their TPM ACPI table entry. I have added the vendor
specific IDs that I know about and added a module parameter that a user can
specify another HID to the probe list if their device isn't being found by the
default list.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a boolean module parameter that allows the user to turn
interrupt support on and off. The default behavior is to attempt to use
interrupts.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use __devexit_p() for the exit/remove function to protect against
discarding it.
WARNING: drivers/char/tpm/tpm_infineon.o - Section mismatch: reference to .exit.text:tpm_inf_pnp_remove from .data between 'tpm_inf_pnp' (at offset 0x20) and 'tpm_inf'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The acpi table which contains the BIOS log events was updated for 1.2.
There are now client and server modes as defined in the specifications with
slightly different formats. Additionally, the start field was even too
small for the 1.1 version but had been working anyway. This patch updates
the code to deal with any of the three types of headers probperly (1.1, 1.2
client and 1.2 server).
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The memory start and length values obtained from the ACPI entry need to be
checked and filled in with the default values from the specification if
they don't exist. This patch fills in the default values and uses them
appropriately.
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apply the latest changes in the TPM interface to the Infineon TPM-driver.
Signed-off-by: Marcel Selhorst <selhorst@crypto.rub.de>
Acked-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use set_bit() and clear_bit() for dev_mask manipulation.
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The timeout and duration values used in the tpm driver are not exposed to
userspace. This patch converts the storage units to jiffies with
msecs_to_jiffies. They were always being used in jiffies so this
simplifies things removing the need for calculation all over the place.
The change necessitated a type change in the tpm_chip struct to hold
jiffies.
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver for the next generation of TPM chips version 1.2 including support
for interrupts. The Trusted Computing Group has written the TPM Interface
Specification (TIS) which defines a common interface for all manufacturer's
1.2 TPM's thus the name tpm_tis.
Signed-off-by: Leendert van Doorn <leendert@watson.ibm.com>
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many of the sysfs files were calling the TPM_GetCapability command with array.
Since for 1.2 more sysfs files of this type are coming I am generalizing the
array so there can be one array and the unique parts can be filled in just
before the command is called.
This updated version of the patch breaks the multi-value sysfs file into
separate files pointed out by Greg. It also addresses the code redundancy and
ugliness in the tpm_show_* functions pointed out on another patch by Dave
Hansen.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the TPM 1.2 Specification, each command is classified as short, medium or
long and the chip tells you the maximum amount of time for a response to each
class of command. This patch provides and array of the classifications and a
function to determine how long the response should be waited for. Also, it
uses that information in the command processing to determine how long to poll
for. The function is exported so the 1.2 driver can use the functionality to
determine how long to wait for a DataAvailable interrupt if interrupts are
being used.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes in the 1.2 TPM Specification make it necessary to update some fields
of the chip structure in the initialization function after it is registered
with tpm.c thus tpm_register_hardware was modified to return a pointer to the
structure. This patch makes that change and the associated changes in
tpm_atmel and tpm_nsc. The changes to tpm_infineon will be coming in a patch
from Marcel Selhorst.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To assist with chip management and better support the possibility of having
multiple TPMs in the system of the same kind, the struct tpm_vendor_specific
member of the tpm_chip was changed from a pointer to an instance. This patch
changes that declaration and fixes up all accesses to the structure member
except in tpm_infineon which is coming in a patch from Marcel Selhorst.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many of the sysfs files were calling the TPM_GetCapability command with array.
Since for 1.2 more sysfs files of this type are coming I am generalizing the
array so there can be one array and the unique parts can be filled in just
before the command is called.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch set contains numerous changes to the base tpm driver
(tpm.c) to support the next generation of TPM chips. The changes include new
sysfs files because of more relevant data being available, a function to
access the timeout and duration values for the chip, and changes to make use
of those duration values. Duration in the TPM specification is defined as the
maximum amount of time the chip could take to return the results. Commands
are in one of three categories short, medium and long. Also included are
cleanups of how the commands for the sysfs files are composed to reduce a
bunch of redundant arrays.
This patch:
Fix minor spacing issues.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A string corresponding to the tcpa_pc_event_id POST_CONTENTS was missing
causing an overflow bug when access was attempted in the get_event_name
function.
This bug was found by Coverity.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The eventname was kmalloc'd and not freed in the *_show functions.
This bug was found by Coverity.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
from: Greg Howard <ghoward@sgi.com>
Fix Altix system controller (snsc) device names to include the slot number
of the blade whose associated system controller is the target of the device
interface. Including the slot number avoids a problem we're currently
having where slots within the same enclosure are attempting to create
multiple kobjects with identical names.
Signed-off-by: Greg Howard <ghoward@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a possible Oops in the Siemens Gigaset base driver when the device is
unplugged while an ISDN connection is still active, and makes sure that the
isdn4linux link level (LL) is properly informed if a connection is broken
by the USB cable being unplugged.
- Avoid unsafe checks of URB status fields outside the URB completion
handlers, keep track of in-use URBs myself instead.
- If an isochronous transfer URB completes with status==0, also check the
status of the frame descriptors.
- Verify length of interrupt messages received from the device.
- Align the length limit on transmitted AT commands with the device
documentation.
- In case of AT response receive overrun, keep newly arrived instead of old
unread data.
- Remove redundant check of device ID in the USB probe function.
- Correct and improve some comments and formatting.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using the old ioctl interface together with cardbus card gives a NULL
pointer dereference since cardbus devices don't have a struct pcmcia_device.
also s->io[0].res can be NULL as well.
Fix is to move the pcmcia code after the cardbus code and to check for a null
pointer.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch updates "depends on" for PCMCIA_VRC4171.
CONFIG_VRC4171 has been removed, so replace it with CPU_VR41XX && ISA.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As static maps do not have IO resources, this setting oopses. However, as
we do not ever read this value, we can safely remove it.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If we set dev_node to NULL too early, some drivers which used this to
determine whether unregister_netdev() needs to be called fail when removing
a PCMCIA card.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The comment of "pcmcia_load_firmware" is wrong: the
firmware(*.cis) files reside in /lib/firmware/ _not_
/lib/firmware/cis/ .
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use list_add instead of list_add_tail for pcmcia_device_add
so that second device of multi-function-card will be unloaded first.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This means "DMA Read returns" can bypass "MMIO Writes".
Violating the PCI specs in this case improves outbound DMA "flows"
and is currently not required by any drivers.
This is NOT a new behavior. Previous chipsets did this
already and I believe ZX1 PDC was already setting this
for hpux. I just want to further document the behavior.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
SERIAL_SGI_IOC4 and BLK_DEV_SGIIOC4 depend upon SGI_IOC4, and
SERIAL_SGI_IOC3 depends upon SGI_IOC3. Currently the definitions
are out of order in the config sequence.
Fix by including drivers/sn/Kconfig immediately after SGI_SN,
upon which SGI_IOC4 and SGI_IOC3 depend.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes an oops in 2.6.16.X when loading the snd_powermac module. The
name of the requested module changed during the 2.6.16 development cycle
from i2c-keylargo to i2c-powermac.
Signed-off-by: Guido Guenther <agx@sigxcpu.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes several bugs in the gianfar driver, including a major one
where spinlocks were horribly broken:
* Split gianfar locks into two types: TX and RX
* Made it so gfar_start() now clears RHALT
* Fixed a bug where calling gfar_start_xmit() with interrupts off would
corrupt the interrupt state
* Fixed a bug where a frame could potentially arrive, and never be handled
(if no more frames arrived
* Fixed a bug where the rx_work_limit would never be observed by the rx
completion code
* Fixed a bug where the interrupt handlers were not actually protected by
their spinlocks
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
