Changed the attach-function of the dib3000mc-driver to return only one
frontend. In case of multiple dib3000-chips on one board, one has to call the
i2c-enumeration manually before.
Added a field to Microtune 2060 config to output the clock to other
tuners/device on a board.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I had forgotten to add the wrapper round the tua6100_attach function if its
disabled in Kconfig
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver was originally in budget-av.c, however I have extracted it into
a seperate file to permit reuse.
I also reworked the code to make it maintainable. I then examined the KNC1
windows drivers and rewrote the code in order to configure the PLL as they
do. This solves a lot of reported tuning problems.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx22702 returns an 8 bit unshifted value for signal strength; this is
inconsistent with most other frontends
Signed-off-by: Bradley Derek Kite <bradley.kite@gmail.com>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The release callback was installed in ops.release, it should have been
ops.release_sec. This prevented to front-end release from getting
called.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Matthieu Castet found that with the rewritten dib3000mc-driver the PID-parsing
was handled correctly. This changeset fixes it.
Thanks Matthieu
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
More register setup which improves the ZL10353's tuning characteristics.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Force parallel transport stream output on the ZL10353 attached to a
bluebird device.
Addresses the problem where a frontend lock was observed, but no MPEG
transport data was received.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
lnbp21 module must use fe->ops.release_sec, not fe->ops.release.
The release function of the frontend driver was never called for cards
with lnbp21...
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Forget to put the MODULE-define and thus to give the license. Now GPL
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
1) It sets LNBDCPol differently based on the card type. Now it should
work properly for both the kworld and geniatech cards.
2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command
(the cx88-dvb level handles the actual voltage on/off, but it still
passes the ioctl down to the cx24123 level, which previously rejected
the OFF as invalid so the ioctl would report failure)
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Yeasah Pell <yeasah@schwide.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hardware algorithm needs to be configured to:
1) Increase timeout constants, to detect weaker signals;
2) do a wider zigzag search.
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed and commented a small debug function.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The VGA was not turned on after calling sleep. This lead to bad performance in difficult areas.
Signed-off-by: matthieu castet <castet.matthieu@free.fr>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
DiB3000MC: set FE to NULL after being freed
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The first commit omitted the common-code and header-files.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A complete rewrite of the DiB3000MC/P driver has been done. It is now much more
easy to maintain and to get improvements inside.
Additionally the tuning time has been reduced and the usage of the driver is
much more understandable now.
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
removing the dib3000-common-module. The common stuff is not common anymore - it will be only used by the 3000mb-driver.
A new 3000mc/p-driver will be added which will share common stuff with dib7000.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
new tuner api
minor fixes for tuning
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When debugging was disabled at lot of empty lines where printed anyway.
Reported by Rolf Ahrenberg and Sergei Haller.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some minor code cleanups and added the MT2060 to new v4l-dvb-build-system, preliminarily under dvb/frontends.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- AGC gain set to 3
- The tuning sequence has been changed to match the DibCom driver ( from I2C
spy captures )
- For LITE-ON adapters : The IF1 frequency is now tuned according to the
calibration values stored in EEPROM.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- some coding style fixes for newly added mt2060
- moved agc-config from fixed values in dib3000mc to configurable ones
- whitespace clean-ups for usb-id-file
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- MT2060 tuner driver
- Added support for some USB DVB-T devices based on Dib3000P
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typical wiring of MT352 and ZL10353 based tuners differs from dvb-pll's
expectation that the PLL is directly accessible. On these boards, the
PLL is actually hidden behind the demodulator, and as such can only be
accessed via the demodulator's interface. It was failing to communicate
with the PLL during an attach test and subsequently not connecting the
tuner ops.
By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility
check can be bypassed. Do this for the affected boards. Also fix a
possible NULL dereference at sleep time, which would otherwise be
exposed by this change.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change this card to use HW ALGO tuning
Signed-off-by: Yeasah Pell <yeasah@schwide.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the bit error counter configuration to be the actual BER.
Originally it was reporting UCB.
Signed-off-by: Yeasah Pell <yeasah@schwide.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Set the Soft decision threshold properly for the specified FEC
Signed-off-by: Yeasah Pell <yeasah@schwide.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tda826x detection was (correctly) cleaned up earlier, but unfortunately
changing the number of received i2c messages from 2 -> 1 was missed. This
fixes it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This was breaking the build if i2c was not previously set
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As opposed to printk() at the moment, which will fill logs uselessly
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the 0-byte write that precedes 2-byte read.
Move initialize the info field in the static tuner_ops definition, so
that it doesn't need to be done manually.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TDA10086 is a new DVB-S demodulator
TDA826x is a DVB-S Silicon Tuner
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I added a duplicate method during one of the previous dvb_attach attempts.
This removes the unnecessary duplication.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow it to be en/disabled
Disable it in < 2.6.17 due to symbol_xxx() bug
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rewrote _write() calls to use write() op.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert SEC drivers to new frontend API
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several DVB modules depends on I2C
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho pointed out that the pll test i2c transmission is slightly
wrong; it was transmitting a zero length message, and then reading from the
PLL. This was wrong; it should only be transmitting a single read i2c message.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Supplying a NULL i2c adapter to dvb_pll_attach is allowed, for example with
mt352 demods. However, the pll i2c probe will segfault because it does not
check for this.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It was pointed out on the mailing list that this PLL definition is broken. I
went back to the original dibusb driver and confirmed it used to use these
settings, as well as consulting the datasheet.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cards have multiple possible addresses for their PLLs, with no other
way to tell if a PLL is present or not apart from probing to see if an i2c
device is present. This adds a quick check to see if an i2c device is
present at the given i2c address.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stumbled over this because of coverity (id #492),
seems like we are missing a return statement here and fail
to do proper bounds checking. If this assumption is false
we should at least change the identation to make it clear
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
