Extend erase timeout in M25P80 SPI Flash driver.
The M25P80 drivers fails erasing sectors on a M25P128 because the ready
wait timeout is too short. Change the timeout from a simple loop count to a
suitable number of seconds.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a logic error in "whole chip erase" for the m25p80 family. If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase. This patch corrects that.
Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc. Increasing it allows me to successfully program
the device on my board.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Follow-on patch to the previous driver model patch for the MTD
framework. This one makes various MTD drivers connect to the
driver model tree, so /sys/devices/virtual/mtd/* nodes are no
longer present ... mostly drivers used on boards I have handy.
Based on a patch from Kay Sievers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Present backing device capabilities for MTD character device files to allow
NOMMU mmap to do direct mapping where possible.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move mtd_has_partitions() and mtd_has_cmdlinepart() inlines from a
DaVinci-specific driver to the <linux/mtd/partitions.h> header.
Use those to eliminate #ifdefs in two drivers which had their own
definitions of mtd_has_partitions().
Quite a lot of other MTD drivers could benefit from using use one or both
of these to remove #ifdeffery. Maybe some Janitors would like to help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove <linux/miscdevice.h> from various drivers which don't actually use
any of its contents. There are still a number of these left in
arch-specific bits of the tree.
(Found by diffing results of "grep -rl" for linux/miscdevice.h and for
misc_register, examining the differences, and verifying removals with a
build test.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert the PS3 Video RAM Storage Driver from an MTD driver to a plain block
device driver.
The ps3vram driver exposes unused video RAM on the PS3 as a block device
suitable for storage or swap. Fast data transfer is achieved using a local
cache in system RAM and DMA transfers via the GPU.
The new driver is ca. 50% faster for reading, and ca. 10% for writing.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 771999b65f ("[MTD] DataFlash: bugfix,
binary page sizes now handled") broke support for probing AT45DB321C flash
chips. These chips do not support the "page size" status bit, so if we
match the JEDEC id return early.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Will Newton <will.newton@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A negative devlength won't get noticed and clean up:
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (67 commits)
[MTD] [MAPS] Fix printk format warning in nettel.c
[MTD] [NAND] add cmdline parsing (mtdparts=) support to cafe_nand
[MTD] CFI: remove major/minor version check for command set 0x0002
[MTD] [NAND] ndfc driver
[MTD] [TESTS] Fix some size_t printk format warnings
[MTD] LPDDR Makefile and KConfig
[MTD] LPDDR extended physmap driver to support LPDDR flash
[MTD] LPDDR added new pfow_base parameter
[MTD] LPDDR Command set driver
[MTD] LPDDR PFOW definition
[MTD] LPDDR QINFO records definitions
[MTD] LPDDR qinfo probing.
[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accurately
[MTD] [NAND] pxa3xx: fix non-page-aligned reads
[MTD] [NAND] fix nandsim sched.h references
[MTD] [NAND] alauda: use USB API functions rather than constants
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] fix m25p80 64-bit divisions
[MTD] fix dataflash 64-bit divisions
[MTD] [NAND] Set the fsl elbc ECCM according the settings in bootloader.
...
Fixed up trivial debug conflicts in drivers/mtd/devices/{m25p80.c,mtd_dataflash.c}
Use _PAGE_NO_CACHE for gpu memory ioremap. Also,
add __iomem attribute to gpu memory pointer and
change use of memset() to memset_io().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace the use of udelay() with msleep() in the looping wait routines
ps3vram_notifier_wait() and ps3vram_wait_ring().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace the use of stdint.h types with kernel types
in the ps3vram driver.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cleanup the ps3vram driver messages. Add a new struct device pointer
variable dev to struct ps3vram_priv and use dev_dbg(), pr_dbg(), etc.
where appropriate.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the ps3vram debug routines ps3vram_dump_ring() and
ps3vram_dump_reports(). These routines are not needed.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update ps3vram driver to use the new ps3 three id modalias support.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ps3vram driver, which exposes unused video RAM on the PS3 as a MTD
device suitable for storage or swap. Fast data transfer is achieved
using a local cache in system RAM and DMA transfers via the GPU.
Signed-off-by: Vivien Chappelier <vivien.chappelier@free.fr>
Signed-off-by: Jim Paris <jim@jtan.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
MTD has recently been upgraded for 64-bit support, see commit
number 69423d99fc in the
mtd-2.6.git tree (git://git.infradead.org/mtd-2.6.git)
or see this URL:
http://git.infradead.org/mtd-2.6.git?a=commit;h=69423d99fc182a81f3c5db3eb5c140acc6fc64be
Some variables in MTD data structures which were 32-bit
became 64-bit. Namely, the 'size' field in 'struct mtd_info'
and the 'addr'/'len' fields in 'struct erase_info'. This
means we have to use 'do_div' to divide them.
This patch fixes the following linking error:
ERROR: "__umoddi3" [drivers/mtd/devices/m25p80.ko] undefined!
This patch changes divisions of 64-bit variable so that they use
'do_div'. This patch also change some print placeholders to
get rid of gcc warnings.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD has recently been upgraded for 64-bit support, see commit
number 69423d99fc in the
mtd-2.6.git tree (git://git.infradead.org/mtd-2.6.git)
or see this URL:
http://git.infradead.org/mtd-2.6.git?a=commit;h=69423d99fc182a81f3c5db3eb5c140acc6fc64be
Some variables in MTD data structures which were 32-bit
became 64-bit. Namely, the 'size' field in 'struct mtd_info'
and the 'addr'/'len' fields in 'struct erase_info'. This
means we have to use 'do_div' to divide them.
This patch fixes the following linking error:
ERROR: "__udivdi3" [drivers/mtd/devices/mtd_dataflash.ko] undefined!
ERROR: "__umoddi3" [drivers/mtd/devices/mtd_dataflash.ko] undefined!
This patch changes divisions of 64-bit variable so that they use
'do_div'. This patch also change some print placeholders to
get rid of gcc warnings.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The symbols lart_flash_init, lart_flash_exit are needlessly
defined global in drivers/mtd/devices/lart.c, so make them
static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes broken terminology added in the "m25p80.c erase enhance" patch,
which added a chip erase command but called it "block erase". There are
already two block erase commands; blocks are 4KiB or 32KiB. There's also
a sector erase (usually 64 KiB). Chip erase typically covers Megabytes.
OPCODE_BE ==> OPCODE_CHIP_ERASE
erase_block ==> erase_chip
[dbrownell@users.sourceforge.net: update sector erase comments too ]
Signed-off-by: Chen Gong <clumsycg@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but seems to break on flashes
which don't have an extended id defined. If the table does not have an
extid defined, then we should ignore it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but in the process managed to
break detection of all flashes.
The ext jedec id check was inserted into an if statement that lacked
braces, and it did not add the required braces. As such, the detection
routine always returns the first entry in the SPI flash list.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
replace open_bdev_excl/close_bdev_excl with variants taking fmode_t.
superblock gets the value used to mount it stored in sb->s_mode
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This reverts commit 75d0ee2202.
Although it seems ObviouslyCorrect™, the spi_write() call uses DMA,
while spi_write_then_read() does not. Since our buffer is on the stack,
we must use the latter even though we don't actually want to read
anything back.
Pointed out by David Brownell <david-b@pacbell.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- add extended device information support
- add s25sl128 device support
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds an erase_block command to enhance erase operation
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds a WRITE_VERIFY Kconfig option to the DataFlash driver,
closely mirroring the similar NAND and ONENAND options, giving
an option to disable some code that's currently always enabled.
Removing this step probably saves a millisecond or so per page
when writing data, which will add up quickly since these pages
are small (the largest is 1 KiB). It doesn't seem to add a
lot in terms of reliability, and wouldn't detect errors which
crop up when transferring data to the on-chip SRAM buffer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
> > linux-next-20080805/drivers/mtd/devices/mtd_dataflash.c: In function 'add_dataflash_otp':
> > linux-next-20080805/drivers/mtd/devices/mtd_dataflash.c:670: error: too many arguments to function 'otp_setup'
Whoops, sorry ... I see what was going on. My bad.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that we can tell when we have one of the newer DataFlash chips,
optionally expose the 128 bytes of OTP memory they provide. Tested
on at45db642 revision B and D chips.
Switch mtdchar over to a generic HAVE_MTD_OTP flag instead of adding
another #ifdef for each type of chip whose driver has OTP support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The wrong version of the "teach dataflash about binary density" patch
just got merged (v2 not v3) ... this restores the missing updates:
* Fix the cmdlinepart *regression* that caused testing failures (!!)
by restoring the original part labels in relevant cases.
* Don't reference things that don't exist (!)
- An opcode that doesn't even exist for DataFlash
- The part is "at45db642" not "at45db641"
- ID zero in this JEDEC table
* Make the JEDEC probe routine report and handle errors better:
- If the SPI calls fail, return the error codes.
- Don't depend on ordering of table entries.
- Unrecognized ids are different from parts that have no ID.
We won't actually know how to handle them correctly; display
the ID and ignore the chip.
* Move the original block comment about the "legacy" chip ID scheme
back next to the code to which it applies ... not next to the new
JEDEC query code, which uses an entirely different strategy.
* Don't print a guessed erasesize; /proc/mtd has the real value.
And add a few more comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This changes the MTD core to handle pci_name() now returning a constant
string.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Such a hardcoded address can cause a checkstop or machine check if
the driver is in the kernel but the address is not acknowledged.
Both drivers allow an address to be specified as either a module
parameter or config option. Any future powerpc board should either
use one of these methods or find the address in the device tree.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Atmel serial flash tends to power up with the protection status bits set.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=4089
[michael.hennerich@analog.com: remove duplicate code]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- Add support for binary page size DataFlashes.
- The driver now prints out pagesize and erasesize.
Printout valuable information for creating flash filesystems.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adding the ability to get a physical address from point() in addition
to virtual address. This physical address is required for XIP of
userspace code from flash.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Reviewed-by: Jörn Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Every file should include the headers containing the externs for its
global functions (in this case for mtdram_init_device()).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Address a number of small issues mainly regarding the output made by this
driver to dmesg:
- Some of the blkmtd's had not been changed to block2mtd which caused
display problem
- the parse_err() macro was displaying "block2mtd: " twice
Signed-off-by: Stéphane Chazelas <stephane.chazelas@emerson.com>
Acked-by: Jörn Engel <joern@lazybastard.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The block2mtd driver (drivers/mtd/devices/block2mtd.c) will kfree an on-stack
pointer when handling an invalid argument line (e.g.
block2mtd=/dev/loop0,xxx).
The kfree was added some time ago when "name" was dynamically allocated.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Acked-by: Joern Engel <joern@lazybastard.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: <stable@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (120 commits)
[MTD] Fix mtdoops.c compilation
[MTD] [NOR] fix startup lock when using multiple nor flash chips
[MTD] [DOC200x] eccbuf is statically defined and always evaluate to true
[MTD] Fix maps/physmap.c compilation with CONFIG_PM
[MTD] onenand: Add panic_write function to the onenand driver
[MTD] mtdoops: Use the panic_write function when present
[MTD] Add mtd panic_write function pointer
[MTD] [NAND] Freescale enhanced Local Bus Controller FCM NAND support.
[MTD] physmap.c: Add support for multiple resources
[MTD] [NAND] Fix misparenthesization introduced by commit 78b65179...
[MTD] [NAND] Fix Blackfin NFC ECC calculating bug with page size 512 bytes
[MTD] [NAND] Remove wrong operation in PM function of the BF54x NFC driver
[MTD] [NAND] Remove unused variable in plat_nand_remove
[MTD] Unlocking all Intel flash that is locked on power up.
[MTD] [NAND] at91_nand: Make mtdparts option can override board info
[MTD] mtdoops: Various minor cleanups
[MTD] mtdoops: Ensure sequential write to the buffer
[MTD] mtdoops: Perform write operations in a workqueue
[MTD] mtdoops: Add further error return code checking
[MTD] [NOR] Test devtype, not definition in flash_probe(), drivers/mtd/devices/lart.c
...
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Acked-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I have been prime author and maintainer of block2mtd from day one, but
neither MAINTAINERS nor the module source makes this fact clear. And while
I'm at it, update my email addresses tree-wide, as the old address
currently bounces and change my name to "joern" as unicode will likely
continue to cause trouble until the end of this century.
Signed-off-by: Joern Engel <joern@lazybastard.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/mtd/devices/lart.c:119:#define FLASH_DEVICE_16mbit_BOTTOM 0x88f488f4
As was, unless "manufacturer != FLASH_MANUFACTURER" this returned true
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
After writing to a Dataflash page, the built-in compare operation is
used to check that the page was successfully written. A logic bug in
checking the results of the comparison currently causes the compare to
never fail.
This bug was originally in the legacy at91_dataflash.c driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This reverts commit 340ea370c2.
It's not needed given the other m25p80 patch (which now handles
at26 "dataflash" as well as most other standard SPI flash chips),
and requires a controller driver that won't be merged upstream
(supplanted by drivers/spi/atmel_spi.c) ... the submitter of
that at91_dataflash26.c driver concurred.
Requested by David Brownell <david-b@pacbell.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch has removed Ocelot G support from MTD.
Ocelot G support has already removed since May 2007.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The CONFIG_MTD_PMC551_APERTURE_SIZE option seems to never have existed,
so there's no reason for carrying an #ifdef for it.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The MTD DataFlash driver uses a semaphore as mutex. Use the mutex API instead
of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Update chip ID tables in m25p80 to handle more SPI flash chips, matching
datasheets. All of these can use the same core operations and are newer
chips that support the JEDEC "read id" instruction:
- Atmel AT25 and AT26 (seven chips)
- Spansion S25SL (five chips)
- SST 25VF (four chips)
- ST M25, M45 (five more chips)
- Winbond W25X series (seven chips)
That JEDEC instruction is now used, either to support a sanity check on the
platform data holding board configuration data, or to determine chip type
when it's not included in platform data. In fact, boards that don't need a
standard partition table may not need that platform data any more.
For chips that support 4KiB erase units, use that smaller block size instead
of the larger size (usually 64KiB); it's less wasteful. (Tested on W25X80.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Convert semaphore usage in m25p80 driver to mutex; mention another kind of
SPI flash chip that should be able to use this driver (given minor tweaks).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I have made a tool to parse the kernel that does not pre-process the
source. That means that my parser tries to parse all the code, including
code in the #else branch or code that is not often compiled because the
driver is not very used (or not used at all). So, my parser sometimes
reports parse error not originally detected by gcc. Here is my (first)
patch.
[akpm@linux-foundation.org: fix amd8111e.c]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (21 commits)
[MTD] [CHIPS] Remove MTD_OBSOLETE_CHIPS (jedec, amd_flash, sharp)
[MTD] Delete allegedly obsolete "bank_size" field of mtd_info.
[MTD] Remove unnecessary user space check from mtd.h.
[MTD] [MAPS] Remove flash maps for no longer supported 405LP boards
[MTD] [MAPS] Fix missing printk() parameter in physmap_of.c MTD driver
[MTD] [NAND] platform NAND driver: add driver
[MTD] [NAND] platform NAND driver: update header
[JFFS2] Simplify and clean up jffs2_add_tn_to_tree() some more.
[JFFS2] Remove another bogus optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remove broken insert_point optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remember to calculate overlap on nodes which replace older nodes
[JFFS2] Don't advance c->wbuf_ofs to next eraseblock after wbuf flush
[MTD] [NAND] at91_nand.c: CMDLINE_PARTS support
[MTD] [NAND] Tidy up handling of page number in nand_block_bad()
[MTD] block2mtd_paramline[] mustn't be __initdata
[MTD] [NAND] Support multiple chips in CAFÉ driver
[MTD] [NAND] Rename cafe.c to cafe_nand.c and remove the multi-obj magic
[MTD] [NAND] Use rslib for CAFÉ ECC
[RSLIB] Support non-canonical GF representations
[JFFS2] Remove dead file histo_mips.h
...
Ensure pages are uptodate after returning from read_cache_page, which allows
us to cut out most of the filesystem-internal PageUptodate calls.
I didn't have a great look down the call chains, but this appears to fixes 7
possible use-before uptodate in hfs, 2 in hfsplus, 1 in jfs, a few in
ecryptfs, 1 in jffs2, and a possible cleared data overwritten with readpage in
block2mtd. All depending on whether the filler is async and/or can return
with a !uptodate page.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/modules.txt doesn't exist, but
Documentation/kbuild/modules.txt does.
Signed-off-by: Alexander E. Patrakov
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
block2mtd_paramline[] is used in the non-__init block2mtd_setup()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Joern Engel <joern@lazybastard.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for AT26Fxxx dataflash devices. These devices have a quite different
commandset than the AT45xxx chips, which are handled by at91_dataflash.c, so a
combined driver turned out to be more ugly than useful.
Tested only on AT26F004.
Signed-off-by: Hans-Jürgen Koch <hjk@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Over the years there was a slow trickle of complaints against the readahead
code. Most of them concerned performance, Peter Zijlstra stumbled over it
when working unrelated changes and I believe there was an actual bug report.
Oh, Andrew Morton also complained about duplicating code from mm/readahead.c.
It is just not worth it. On flash media like usb sticks, readahead will
make things go slow - very slow. On spinning disks, readahead may be a
win, but this is definitely not the place to add it.
Signed-off-by: Jörn Engel <joern@lazybastard.org>
drivers/mtd/devices/block2mtd.c:311:9: warning: symbol 'dev' shadows an earlier one
drivers/mtd/devices/block2mtd.c:294:23: originally declared here
Signed-off-by: Jörn Engel <joern@lazybastard.org>
Remove two casts - they were not only pointless, but outright harmful.
Spotted by Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jörn Engel <joern@lazybastard.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert all calls to invalidate_inode_pages() into open-coded calls to
invalidate_mapping_pages().
Leave the invalidate_inode_pages() wrapper in place for now, marked as
deprecated.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused and broken mtd->ecctype and mtd->eccsize fields
from struct mtd_info. Do not remove them from userspace API
data structures (don't want to breake userspace) but mark them
as obsolete by a comment. Any userspace program which uses them
should be half-broken anyway, so this is more about saving
data structure size.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Return a fault code if the Dataflash driver runs into a "no device present"
error when the MISO line has a pulldown (it currently expects a pullup), so
that rmmod won't oops.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix build issues that show up with the m25p80 SPI flash driver when
building with MTD debug enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the
"jffs2_flash_writev(): Non-contiguous write to 00825300 with mtd_dataflash" bug.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use pci_resource_start for getting start of regions and pci_iomap to not
doing this directly by using dev->resource... (Thanks to Rolf Eike Beer)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Spaces were used for indent, there was more than 80 columns per line. Get
rid of that stuff.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
