Commit graph

12766 commits

Author SHA1 Message Date
Linus Torvalds
f9da455b93 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.

 2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
    Benniston.

 3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
    Mork.

 4) BPF now has a "random" opcode, from Chema Gonzalez.

 5) Add more BPF documentation and improve test framework, from Daniel
    Borkmann.

 6) Support TCP fastopen over ipv6, from Daniel Lee.

 7) Add software TSO helper functions and use them to support software
    TSO in mvneta and mv643xx_eth drivers.  From Ezequiel Garcia.

 8) Support software TSO in fec driver too, from Nimrod Andy.

 9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.

10) Handle broadcasts more gracefully over macvlan when there are large
    numbers of interfaces configured, from Herbert Xu.

11) Allow more control over fwmark used for non-socket based responses,
    from Lorenzo Colitti.

12) Do TCP congestion window limiting based upon measurements, from Neal
    Cardwell.

13) Support busy polling in SCTP, from Neal Horman.

14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.

15) Bridge promisc mode handling improvements from Vlad Yasevich.

16) Don't use inetpeer entries to implement ID generation any more, it
    performs poorly, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
  rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
  tcp: fixing TLP's FIN recovery
  net: fec: Add software TSO support
  net: fec: Add Scatter/gather support
  net: fec: Increase buffer descriptor entry number
  net: fec: Factorize feature setting
  net: fec: Enable IP header hardware checksum
  net: fec: Factorize the .xmit transmit function
  bridge: fix compile error when compiling without IPv6 support
  bridge: fix smatch warning / potential null pointer dereference
  via-rhine: fix full-duplex with autoneg disable
  bnx2x: Enlarge the dorq threshold for VFs
  bnx2x: Check for UNDI in uncommon branch
  bnx2x: Fix 1G-baseT link
  bnx2x: Fix link for KR with swapped polarity lane
  sctp: Fix sk_ack_backlog wrap-around problem
  net/core: Add VF link state control policy
  net/fsl: xgmac_mdio is dependent on OF_MDIO
  net/fsl: Make xgmac_mdio read error message useful
  net_sched: drr: warn when qdisc is not work conserving
  ...
2014-06-12 14:27:40 -07:00
Linus Torvalds
16b9057804 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
 "This the bunch that sat in -next + lock_parent() fix.  This is the
  minimal set; there's more pending stuff.

  In particular, I really hope to get acct.c fixes merged this cycle -
  we need that to deal sanely with delayed-mntput stuff.  In the next
  pile, hopefully - that series is fairly short and localized
  (kernel/acct.c, fs/super.c and fs/namespace.c).  In this pile: more
  iov_iter work.  Most of prereqs for ->splice_write with sane locking
  order are there and Kent's dio rewrite would also fit nicely on top of
  this pile"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
  lock_parent: don't step on stale ->d_parent of all-but-freed one
  kill generic_file_splice_write()
  ceph: switch to iter_file_splice_write()
  shmem: switch to iter_file_splice_write()
  nfs: switch to iter_splice_write_file()
  fs/splice.c: remove unneeded exports
  ocfs2: switch to iter_file_splice_write()
  ->splice_write() via ->write_iter()
  bio_vec-backed iov_iter
  optimize copy_page_{to,from}_iter()
  bury generic_file_aio_{read,write}
  lustre: get rid of messing with iovecs
  ceph: switch to ->write_iter()
  ceph_sync_direct_write: stop poking into iov_iter guts
  ceph_sync_read: stop poking into iov_iter guts
  new helper: copy_page_from_iter()
  fuse: switch to ->write_iter()
  btrfs: switch to ->write_iter()
  ocfs2: switch to ->write_iter()
  xfs: switch to ->write_iter()
  ...
2014-06-12 10:30:18 -07:00
Linus Torvalds
82abb273d8 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 - three fixes for 3.15 that didn't make it in time
 - limited Octeon 3 support.
 - paravirtualization support
 - improvment to platform support for Netlogix SOCs.
 - add support for powering down the Malta eval board in software
 - add many instructions to the in-kernel microassembler.
 - add support for the BPF JIT.
 - minor cleanups of the BCM47xx code.
 - large cleanup of math emu code resulting in significant code size
   reduction, better readability of the code and more accurate
   emulation.
 - improvments to the MIPS CPS code.
 - support C3 power status for the R4k count/compare clock device.
 - improvments to the GIO support for older SGI workstations.
 - increase number of supported CPUs to 256; this can be reached on
   certain embedded multithreaded ccNUMA configurations.
 - various small cleanups, updates and fixes

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (173 commits)
  MIPS: IP22/IP28: Improve GIO support
  MIPS: Octeon: Add twsi interrupt initialization for OCTEON 3XXX, 5XXX, 63XX
  DEC: Document the R4k MB ASIC mini interrupt controller
  DEC: Add self as the maintainer
  MIPS: Add microMIPS MSA support.
  MIPS: Replace calls to obsolete strict_strto call with kstrto* equivalents.
  MIPS: Replace obsolete strict_strto call with kstrto
  MIPS: BFP: Simplify code slightly.
  MIPS: Call find_vma with the mmap_sem held
  MIPS: Fix 'write_msa_##' inline macro.
  MIPS: Fix MSA toolchain support detection.
  mips: Update the email address of Geert Uytterhoeven
  MIPS: Add minimal defconfig for mips_paravirt
  MIPS: Enable build for new system 'paravirt'
  MIPS: paravirt: Add pci controller for virtio
  MIPS: Add code for new system 'paravirt'
  MIPS: Add functions for hypervisor call
  MIPS: OCTEON: Add OCTEON3 to __get_cpu_type
  MIPS: Add function get_ebase_cpunum
  MIPS: Add minimal support for OCTEON3 to c-r4k.c
  ...
2014-06-09 18:10:34 -07:00
Linus Torvalds
3f17ea6dea Merge branch 'next' (accumulated 3.16 merge window patches) into master
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.

* accumulated work in next: (6809 commits)
  ufs: sb mutex merge + mutex_destroy
  powerpc: update comments for generic idle conversion
  cris: update comments for generic idle conversion
  idle: remove cpu_idle() forward declarations
  nbd: zero from and len fields in NBD_CMD_DISCONNECT.
  mm: convert some level-less printks to pr_*
  MAINTAINERS: adi-buildroot-devel is moderated
  MAINTAINERS: add linux-api for review of API/ABI changes
  mm/kmemleak-test.c: use pr_fmt for logging
  fs/dlm/debug_fs.c: replace seq_printf by seq_puts
  fs/dlm/lockspace.c: convert simple_str to kstr
  fs/dlm/config.c: convert simple_str to kstr
  mm: mark remap_file_pages() syscall as deprecated
  mm: memcontrol: remove unnecessary memcg argument from soft limit functions
  mm: memcontrol: clean up memcg zoneinfo lookup
  mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
  mm/mempool.c: update the kmemleak stack trace for mempool allocations
  lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
  mm: introduce kmemleak_update_trace()
  mm/kmemleak.c: use %u to print ->checksum
  ...
2014-06-08 11:31:16 -07:00
Linus Torvalds
d09cc3659d Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next
Pull core irq updates from Thomas Gleixner:
 "The irq department delivers:

   - Another tree wide update to get rid of the horrible create_irq
     interface along with its even more horrible variants.  That also
     gets rid of the last leftovers of the initial sparse irq hackery.
     arch/driver specific changes have been either acked or ignored.

   - A fix for the spurious interrupt detection logic with threaded
     interrupts.

   - A new ARM SoC interrupt controller

   - The usual pile of fixes and improvements all over the place"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
  Documentation: brcmstb-l2: Add Broadcom STB Level-2 interrupt controller binding
  irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller
  genirq: Improve documentation to match current implementation
  ARM: iop13xx: fix msi support with sparse IRQ
  genirq: Provide !SMP stub for irq_set_affinity_notifier()
  irqchip: armada-370-xp: Move the devicetree binding documentation
  irqchip: gic: Use mask field in GICC_IAR
  genirq: Remove dynamic_irq mess
  ia64: Use irq_init_desc
  genirq: Replace dynamic_irq_init/cleanup
  genirq: Remove irq_reserve_irq[s]
  genirq: Replace reserve_irqs in core code
  s390: Avoid call to irq_reserve_irqs()
  s390: Remove pointless arch_show_interrupts()
  s390: pci: Check return value of alloc_irq_desc() proper
  sh: intc: Remove pointless irq_reserve_irqs() invocation
  x86, irq: Remove pointless irq_reserve_irqs() call
  genirq: Make create/destroy_irq() ia64 private
  tile: Use SPARSE_IRQ
  tile: pci: Use irq_alloc/free_hwirq()
  ...
2014-06-04 15:59:13 -07:00
David S. Miller
c99f7abf0e Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	include/net/inetpeer.h
	net/ipv6/output_core.c

Changes in net were fixing bugs in code removed in net-next.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03 23:32:12 -07:00
Linus Torvalds
776edb5931 Merge branch 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next
Pull core locking updates from Ingo Molnar:
 "The main changes in this cycle were:

   - reduced/streamlined smp_mb__*() interface that allows more usecases
     and makes the existing ones less buggy, especially in rarer
     architectures

   - add rwsem implementation comments

   - bump up lockdep limits"

* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
  rwsem: Add comments to explain the meaning of the rwsem's count field
  lockdep: Increase static allocations
  arch: Mass conversion of smp_mb__*()
  arch,doc: Convert smp_mb__*()
  arch,xtensa: Convert smp_mb__*()
  arch,x86: Convert smp_mb__*()
  arch,tile: Convert smp_mb__*()
  arch,sparc: Convert smp_mb__*()
  arch,sh: Convert smp_mb__*()
  arch,score: Convert smp_mb__*()
  arch,s390: Convert smp_mb__*()
  arch,powerpc: Convert smp_mb__*()
  arch,parisc: Convert smp_mb__*()
  arch,openrisc: Convert smp_mb__*()
  arch,mn10300: Convert smp_mb__*()
  arch,mips: Convert smp_mb__*()
  arch,metag: Convert smp_mb__*()
  arch,m68k: Convert smp_mb__*()
  arch,m32r: Convert smp_mb__*()
  arch,ia64: Convert smp_mb__*()
  ...
2014-06-03 12:57:53 -07:00
Linus Torvalds
e5c4ecdc55 USB driver patches for 3.16-rc1
Here is the big USB driver pull request for 3.16-rc1.
 
 Nothing huge here, but lots of little things in the USB core, and in
 lots of drivers.  Hopefully the USB power management will be work better
 now that it has been reworked to do per-port power control dynamically.
 There's also a raft of gadget driver updates and fixes, CONFIG_USB_DEBUG
 is finally gone now that everything has been converted over to the
 dynamic debug inteface, the last hold-out drivers were cleaned up and
 the config option removed.  There were also other minor things all
 through the drivers/usb/ tree, the shortlog shows this pretty well.
 
 All have been in linux-next, including the very last patch, which came
 from linux-next to fix a build issue on some platforms.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iEYEABECAAYFAlONYEMACgkQMUfUDdst+ynxvgCggMQBhN5icth8Y5hFglNNaISN
 c4AAoMHR2kb62U1plylLbPnboQTjfcl0
 =fG6y
 -----END PGP SIGNATURE-----

Merge tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into next

Pull USB driver updates from Greg KH:
 "Here is the big USB driver pull request for 3.16-rc1.

  Nothing huge here, but lots of little things in the USB core, and in
  lots of drivers.  Hopefully the USB power management will be work
  better now that it has been reworked to do per-port power control
  dynamically.  There's also a raft of gadget driver updates and fixes,
  CONFIG_USB_DEBUG is finally gone now that everything has been
  converted over to the dynamic debug inteface, the last hold-out
  drivers were cleaned up and the config option removed.  There were
  also other minor things all through the drivers/usb/ tree, the
  shortlog shows this pretty well.

  All have been in linux-next, including the very last patch, which came
  from linux-next to fix a build issue on some platforms"

* tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (314 commits)
  usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=y
  USB: orinoco_usb: remove CONFIG_USB_DEBUG support
  USB: media: lirc: igorplugusb: remove CONFIG_USB_DEBUG support
  USB: media: streamzap: remove CONFIG_USB_DEBUG
  USB: media: redrat3: remove CONFIG_USB_DEBUG usage
  USB: media: redrat3: remove unneeded tracing macro
  usb: qcserial: add additional Sierra Wireless QMI devices
  usb: host: max3421-hcd: Use module_spi_driver
  usb: host: max3421-hcd: Allow platform-data to specify Vbus polarity
  usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning
  usb: host: max3421-hcd: Fix missing unlock in max3421_urb_enqueue()
  usb: qcserial: add Netgear AirCard 341U
  Documentation: dt-bindings: update xhci-platform DT binding for R-Car H2 and M2
  usb: host: xhci-plat: add xhci_plat_start()
  usb: host: max3421-hcd: Fix potential NULL urb dereference
  Revert "usb: gadget: net2280: Add support for PLX USB338X"
  USB: usbip: remove CONFIG_USB_DEBUG reference
  USB: remove CONFIG_USB_DEBUG from defconfig files
  usb: resume child device when port is powered on
  usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y
  ...
2014-06-03 09:11:20 -07:00
Linus Torvalds
c67d9ce166 ARM: SoC board support updates for 3.16
The bulk of this branch is updates for Renesas Shmobile. They are still
 doing some enablement for classic boards first, and then come up with DT
 bindings when they've had a chance to learn more about the hardware. Not
 necessarily a bad way to go about it, and they're looking at moving some
 of the temporary board code resulting from it to drivers/staging instead
 to avoid the churn here.
 
 As a result of the shmobile clock cleanups, we end up merging quite a
 bit of SH code here as well. We ended up merging it here instead of in
 the cleanup branch due to the other board changes depending on it.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.14 (GNU/Linux)
 
 iQIcBAABAgAGBQJTjNClAAoJEIwa5zzehBx3Q7wP+wYzWTAU0+3BnnjJpQM79hsX
 1hP89RaM6DEyTf6PiL/AKOHsnDponUhNzZu1W5FvNG6cFVenh/nxbmO65FKX9CrY
 Ap2pkQW+/IcpmIKZ+Hln2bkCc54a6yPouK+5pd9W14X5TtqNmLbdh1qhoq9UjFTo
 zgLfhch5tyNqfpNOj0vFsmvTw0ZGJ0Neq6olRqQbXmyAaRaWzDa64lmEKVupMdk7
 2Fh/8jeXlVlryi7p7CvNoAmZEMm7+We5ZMVsQXLk8b9zcwuCWK0DZzNW4DnRCB1d
 lsNM/Sygi3Y5zRj2XogNANVhNDIih0f50FX7uuKtmevWNJE9n4To7uFUMTk/3zBt
 1hvJLL8w4WHhzkg5v5nFsiCTx65pFaTD/LocPj8lhQ1AYzUvWN5sKPxW0uC1lvJ9
 Unlwdc0C4EWs3yq6hAPUZS2eB7owmzNUWdjdkgKfdc74u5RnRay0pUmbRMJm2l20
 OKoDSwaluQZUeHrxPnTSLdgpkBbPRn9M5DbswEQsuPyI6yROgCRxaRQ4XcpM93dV
 4obCF+fOvX6dtsdIUBCtdhvmJ/iHqhQlPLc2avpt2gyti7eWjQkt5it12hjjOF6A
 DVBdNHv215EEgvB0MbPJvFVKBLw4boxdeBx+FqMQCqvAbqefHo4gcQZcsUGAv/pX
 zJ8jgkYhlt7XTd+6GlJu
 =lWof
 -----END PGP SIGNATURE-----

Merge tag 'boards-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next

Pull ARM SoC board support updates from Olof Johansson:
 "The bulk of this branch is updates for Renesas Shmobile.  They are
  still doing some enablement for classic boards first, and then come up
  with DT bindings when they've had a chance to learn more about the
  hardware.  Not necessarily a bad way to go about it, and they're
  looking at moving some of the temporary board code resulting from it
  to drivers/staging instead to avoid the churn here.

  As a result of the shmobile clock cleanups, we end up merging quite a
  bit of SH code here as well.  We ended up merging it here instead of
  in the cleanup branch due to the other board changes depending on it"

* tag 'boards-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (130 commits)
  ARM: davinci: remove checks for CONFIG_USB_MUSB_PERIPHERAL
  ARM: add drivers for Colibri T30 to multi_v7_defconfig
  ARM: shmobile: Remove Genmai reference DTS
  ARM: shmobile: Let Genmai multiplatform boot with Genmai DTB
  ARM: shmobile: Sync Genmai DTS with Genmai reference DTS
  ARM: shmobile: genmai-reference: Remove legacy clock support
  ARM: shmobile: Remove non-multiplatform Genmai reference support
  ARM: configs: enable XHCI mvebu support in multi_v7_defconfig
  ARM: OMAP: replace checks for CONFIG_USB_GADGET_OMAP
  ARM: OMAP: AM3517EVM: remove check for CONFIG_PANEL_SHARP_LQ043T1DG01
  ARM: OMAP: SX1: remove check for CONFIG_SX1_OLD_FLASH
  ARM: OMAP: remove some dead code
  ARM: OMAP: omap3stalker: remove two Kconfig macros
  ARM: tegra: tegra_defconfig updates
  ARM: shmobile: r7s72100: use workaround for non DT-clocks
  ARM: shmobile: Add forward declaration of struct clk to silence warning
  ARM: shmobile: r7s72100: remove SPI DT clocks from legacy clock support
  ARM: shmobile: r7s72100: add spi clocks to dtsi
  ARM: shmobile: r7s72100: remove I2C DT clocks from legacy clock support
  ARM: shmobile: r7s72100: add i2c clocks to dtsi
  ...
2014-06-02 16:21:41 -07:00
Stephen Rothwell
4a95b1fce9 usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=y
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-02 15:16:33 -07:00
Aleksander Morgado
0ce5fb5856 usb: qcserial: add additional Sierra Wireless QMI devices
A set of new VID/PIDs retrieved from the out-of-tree GobiNet/GobiSerial
Sierra Wireless drivers.

Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Link: http://marc.info/?l=linux-usb&m=140136310027293&w=2
Cc: <stable@vger.kernel.org>	# backport in link above
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-29 11:20:26 -07:00
Sachin Kamat
7df45d5fc2 usb: host: max3421-hcd: Use module_spi_driver
module_spi_driver simplifies the code by eliminating
boilerplate code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-29 11:19:30 -07:00
David Mosberger-Tang
4055e5e54e usb: host: max3421-hcd: Allow platform-data to specify Vbus polarity
Signed-off-by: Davidm Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-29 11:19:30 -07:00
David Mosberger-Tang
05dfa5c9bc usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning
kmalloc the SPI rx and tx data buffers.  This appears to be the only
portable way to guarantee that the buffers are DMA-safe (e.g., in
separate DMA cache-lines).  This patch makes the spi_rdX()/spi_wrX()
non-reentrant, but that's OK because calls to them are guaranteed to
be serialized by the per-HCD SPI-thread.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-29 11:19:30 -07:00
David Mosberger-Tang
00c5aa178a usb: host: max3421-hcd: Fix missing unlock in max3421_urb_enqueue()
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-28 16:57:34 -07:00
Aleksander Morgado
ff1fcd50bc usb: qcserial: add Netgear AirCard 341U
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-28 14:56:36 -07:00
Mathias Nyman
5dc2808c47 xhci: delete endpoints from bandwidth list before freeing whole device
Lists of endpoints are stored for bandwidth calculation for roothub ports.
Make sure we remove all endpoints from the list before the whole device,
containing its endpoints list_head stuctures, is freed.

This used to be done in the wrong order in xhci_mem_cleanup(),
and triggered an oops in resume from S4 (hibernate).

Cc: stable <stable@vger.kernel.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-28 14:53:53 -07:00
Yoshihiro Shimoda
94adcdce0d usb: host: xhci-plat: add xhci_plat_start()
Some platforms (such as the Renesas R-Car) need to initialize some specific
registers after xhci driver calls usb_add_hcd() and before the driver calls
xhci_run(). So, this patch adds the xhci_plat_start() function.

Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-28 13:26:43 -07:00
David Mosberger-Tang
f9da25c798 usb: host: max3421-hcd: Fix potential NULL urb dereference
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-28 13:24:07 -07:00
Mathias Nyman
b38f09ccc3 usb: pci-quirks: Prevent Sony VAIO t-series from switching usb ports
Sony VAIO t-series machines are not capable of switching usb2 ports over
from Intel EHCI to xHCI controller. If tried the USB2 port will be left
unconnected and unusable.

This patch should be backported to stable kernels as old as 3.12,
that contain the commit 26b76798e0
"Intel xhci: refactor EHCI/xHCI port switching"

Cc: stable <stable@vger.kernel.org> # 3.12
Reported-by: Jorge <xxopxe@gmail.com>
Tested-by: Jorge <xxopxe@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-28 13:17:46 -07:00
Greg Kroah-Hartman
357d596ea7 Revert "usb: gadget: net2280: Add support for PLX USB338X"
This reverts commit c4128cac35.

This should come through Felipe's tree first, and there was a bunch of
other patches that are needed after this one as well that I didn't have.

Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-28 11:35:41 -07:00
Dan Williams
7027df36e4 usb: resume child device when port is powered on
Unconditionally wake up the child device when the power session is
recovered.

This addresses the following scenarios:

1/ The device may need a reset on power-session loss, without this
   change port power-on recovery exposes khubd to scenarios that
   usb_port_resume() is set to handle.  Prior to port power control the
   only time a power session would be lost is during dpm_suspend of the
   hub.  In that scenario usb_port_resume() is guaranteed to be called
   prior to khubd running for that port.  With this change we wakeup the
   child device as soon as possible (prior to khubd running again for this
   port).

   Although khubd has facilities to wake a child device it will only do
   so if the portstatus / portchange indicates a suspend state.  In the
   case of port power control we are not coming from a hub-port-suspend
   state.  This implementation simply uses pm_request_resume() to wake the
   device and relies on the port_dev->status_lock to prevent any collisions
   between khubd and usb_port_resume().

2/ This mechanism rate limits port power toggling.  The minimum port
   power on/off period is now gated by the child device suspend/resume
   latency.  Empirically this mitigates devices downgrading their connection
   on perceived instability of the host connection.  This ratelimiting is
   really only relevant to port power control testing, but it is a nice
   side effect of closing the above race.  Namely, the race of khubd for
   the given port running while a usb_port_resume() event is pending.

3/ Going forward we are finding that power-session recovery requires
   warm-resets (http://marc.info/?t=138659232900003&r=1&w=2).  This
   mechanism allows for warm-resets to be requested at the same point in
   the resume path for hub dpm_suspend power session losses, or port
   rpm_suspend power session losses.

4/ If the device *was* disconnected the only time we'll know for sure is
   after a failed resume, so it's necessary for usb_port_runtime_resume()
   to expedite a usb_port_resume() to clean up the removed device.  The
   reasoning for this is "least surprise" for the user. Turning on a port
   means that hotplug detection is again enabled for the port, it is
   surprising that devices that were removed while the port was off are not
   disconnected until they are attempted to be used.  As a user "why would
   I try to use a device I removed from the system?"

1, 2, and 4 are not a problem in the system dpm_resume() case because,
although the power-session is lost, khubd is frozen until after device
resume.  For the rpm_resume() case pm_request_resume() is used to
request re-validation of the device, and if it happens to collide with a
khubd run we rely on the port_dev->status_lock to synchronize those
operations.

Besides testing, the primary scenario where this mechanism is expected
to be triggered is when the user changes the port power policy
(control/pm_qos_no_poweroff, or power/control).   Each time power is
enabled want to revalidate the child device, where the revalidation is
handled by usb_port_resume().

Given that this arranges for port_dev->child to be de-referenced in
usb_port_runtime_resume() we need to make sure not to collide with
usb_disconnect() that frees the usb_device.  To this end we hold the
port active with the "child_usage" reference across the disconnect
event.  Subsequently, the need to access hub->child_usage_bits lead to
the creation of hub_disconnect_children() to remove any ambiguity of
which "hub" is being acted on in usb_disconnect() (prompted-by sharp
eyes from Alan).

Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 17:25:37 -07:00
Dan Williams
7e73be227b usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y
Per Alan:
"You mean from within hub_handle_remote_wakeup()?  That routine will
never get called if CONFIG_PM_RUNTIME isn't enabled, because khubd
never sees wakeup requests if they arise during system suspend.

In fact, that routine ought to go inside the "#ifdef CONFIG_PM_RUNTIME"
portion of hub.c, along with the other suspend/resume code."

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:51:51 -07:00
Dan Williams
5c79a1e303 usb: introduce port status lock
In general we do not want khubd to act on port status changes that are
the result of in progress resets or USB runtime PM operations.
Specifically port power control testing has been able to trigger an
unintended disconnect in hub_port_connect_change(), paraphrasing:

	if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
	    udev->state != USB_STATE_NOTATTACHED) {
		if (portstatus & USB_PORT_STAT_ENABLE) {
			/* Nothing to do */
		} else if (udev->state == USB_STATE_SUSPENDED &&
				udev->persist_enabled) {
			...
		} else {
			/* Don't resuscitate */;
		}
	}

...by falling to the "Don't resuscitate" path or missing
USB_PORT_STAT_CONNECTION because usb_port_resume() was in the middle of
modifying the port status.

So, we want a new lock to hold off khubd for a given port while the
child device is being suspended, resumed, or reset.  The lock ordering
rules are now usb_lock_device() => usb_lock_port().  This is mandated by
the device core which may hold the device_lock on the usb_device before
invoking usb_port_{suspend|resume} which in turn take the status_lock on
the usb_port.  We attempt to hold the status_lock for the duration of a
port_event() run, and drop/re-acquire it when needing to take the
device_lock.  The lock is also dropped/re-acquired during
hub_port_reconnect().

This patch also deletes hub->busy_bits as all use cases are now covered
by port PM runtime synchronization or the port->status_lock and it
pushes down usb_device_lock() into usb_remote_wakeup().

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:51:50 -07:00
Dan Williams
097a155f05 usb: synchronize port poweroff and khubd
If a port is powered-off, or in the process of being powered-off, prevent
khubd from operating on it.  Otherwise, the following sequence of events
leading to an unintended disconnect may occur:

Events:
(0) <set pm_qos_no_poweroff to '0' for port1>
(1) hub 2-2:1.0: hub_resume
(2) hub 2-2:1.0: port 1: status 0301 change 0000
(3) hub 2-2:1.0: state 7 ports 4 chg 0002 evt 0000
(4) hub 2-2:1.0: port 1, power off status 0000, change 0000, 12 Mb/s
(5) usb 2-2.1: USB disconnect, device number 5

Description:
(1) hub is resumed before sending a ClearPortFeature request
(2) hub_activate() notices the port is connected and sets
    hub->change_bits for the port
(3) hub_events() starts, but at the same time the port suspends
(4) hub_connect_change() sees the disabled port and triggers disconnect

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:51:50 -07:00
Dan Williams
af376a461c usb: refactor port handling in hub_events()
In preparation for synchronizing port handling with pm_runtime
transitions refactor port handling into its own subroutine.

We expect that clearing some status flags will be required regardless of
the port state, so handle those first and group all non-trivial actions
at the bottom of the routine.

This also splits off the bottom half of hub_port_connect_change() into
hub_port_reconnect() in prepartion for introducing a port->status_lock.
hub_port_reconnect() will expect the port lock to not be held while
hub_port_connect_change() expects to enter with it held.

Other cleanups include:
1/ reflowing to 80 columns
2/ replacing redundant usages of 'hub->hdev' with 'hdev'
3/ consolidate clearing of ->change_bits() in hub_port_connect_change
4/ consolidate calls to usb_reset_device

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:51:50 -07:00
Dan Williams
6908058469 usb: usb3 ports do not support FEAT_C_ENABLE
The port pm_runtime implementation unconditionally clears FEAT_C_ENABLE
after clearing PORT_POWER, but the bit is reserved on usb3 hub ports.
We expect khubd to be prevented from running because the port state is
not RPM_ACTIVE, so we need to clear any errors for usb2 ports.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:51:50 -07:00
Dan Williams
7c604079bd usb: don't clear FEAT_C_ENABLE on usb_port_runtime_resume failure
Three reasons:
1/ It's an invalid operation on usb3 ports
2/ There's no guarantee of when / if a usb2 port has entered an error
   state relative to PORT_POWER request
3/ The port is active / powered at this point, so khubd will clear it as
   a matter of course

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:51:50 -07:00
Dan Williams
7ad3c47088 usb: block suspension of superspeed port while hispeed peer is active
ClearPortFeature(PORT_POWER) on a usb3 port places the port in either a
DSPORT.Powered-off-detect / DSPORT.Powered-off-reset loop, or the
DSPORT.Powered-off state.  There is no way to ensure that RX
terminations will persist in this state, so it is possible a device will
degrade to its usb2 connection.  Prevent this by blocking power-off of a
usb3 port while its usb2 peer is active, and powering on a usb3 port
before its usb2 peer.

By default the latency between peer power-on events is 0.  In order for
the device to not see usb2 active while usb3 is still powering up inject
the hub recommended power_on_good delay.  In support of satisfying the
power_on_good delay outside of hub_power_on() refactor the places where
the delay is consumed to call a new hub_power_on_good_delay() helper.

Finally, because this introduces several new checks for whether a port
is_superspeed, cache that disctinction at port creation so that we don't
need to keep looking up the parent hub device.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
[alan]: add a 'superspeed' flag to the port
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:38:53 -07:00
Dan Williams
d5c3834e4a usb: make usb_port flags atomic, rename did_runtime_put to child_usage
We want to manipulate ->did_runtime_put in usb_port_runtime_resume(),
but we don't want that to collide with other updates.  Move usb_port
flags to new port-bitmap fields in usb_hub. "did_runtime_put" is renamed
"child_usage_bits" to reflect that it is strictly standing in for the
fact that usb_devices are not the device_model children of their parent
port.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:38:53 -07:00
Dan Williams
b7e38eac88 usb: sysfs link peer ports
The usb topology after this change will have symlinks between usb3 ports
and their usb2 peers, for example:

usb2/2-1/2-1:1.0/2-1-port1/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port1
usb2/2-1/2-1:1.0/2-1-port2/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port2
usb2/2-1/2-1:1.0/2-1-port3/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port3
usb2/2-1/2-1:1.0/2-1-port4/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port4
usb2/2-0:1.0/usb2-port1/peer    => ../../../usb3/3-0:1.0/usb3-port1
usb2/2-0:1.0/usb2-port2/peer    => ../../../usb3/3-0:1.0/usb3-port2
usb2/2-0:1.0/usb2-port3/peer    => ../../../usb3/3-0:1.0/usb3-port3
usb2/2-0:1.0/usb2-port4/peer    => ../../../usb3/3-0:1.0/usb3-port4

usb3/3-1/3-1:1.0/usb3-1-port1/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port1
usb3/3-1/3-1:1.0/usb3-1-port2/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port2
usb3/3-1/3-1:1.0/usb3-1-port3/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port3
usb3/3-1/3-1:1.0/usb3-1-port4/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port4
usb3/3-0:1.0/usb3-port1/peer       => ../../../usb2/2-0:1.0/usb2-port1
usb3/3-0:1.0/usb3-port2/peer       => ../../../usb2/2-0:1.0/usb2-port2
usb3/3-0:1.0/usb3-port3/peer       => ../../../usb2/2-0:1.0/usb2-port3
usb3/3-0:1.0/usb3-port4/peer       => ../../../usb2/2-0:1.0/usb2-port4

Introduce link_peers_report() to notify on all link_peers() failure
cases.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:38:53 -07:00
Dan Williams
3bfd659bae usb: find internal hub tier mismatch via acpi
ACPI identifies peer ports by setting their 'group_token' and
'group_position' _PLD data to the same value.  If a platform has tier
mismatch [1] , ACPI can override the default (USB3 defined) peer port
association for internal hubs.  External hubs follow the default peer
association scheme.

Location data is cached as an opaque cookie in usb_port_location data.

Note that we only consider the group_token and group_position attributes
from the _PLD data as ACPI specifies that group_token is a unique
identifier.

When we find port location data for a port then we assume that the
firmware will also describe its peer port.  This allows the
implementation to only ever set the peer once.  This leads to a question
about what happens when a pm runtime event occurs while the peer
associations are still resolving.  Since we only ever set the peer
information once, a USB3 port needs to be prevented from suspending
while its ->peer pointer is NULL (implemented in a subsequent patch).

There is always the possibility that firmware mis-identifies the ports,
but there is not much the kernel can do in that case.

[1]: xhci 1.1 appendix D figure 131
[2]: acpi 5 section 6.1.8

[alan]: don't do default peering when acpi data present
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:38:52 -07:00
Dan Williams
8b1ba80c59 usb: assign usb3 external hub port peers
Given that root hub port peers are already established, external hub peer
ports can be determined by traversing the device topology:

1/ ascend to the parent hub and find the upstream port_dev

2/ walk ->peer to find the peer port

3/ descend to the peer hub via ->child

4/ find the port with the matching port id

Note that this assumes the port labeling scheme required by the
specification [1].

[1]: usb3 3.1 section 10.3.3

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:38:52 -07:00
Dan Williams
d8521afe35 usb: assign default peer ports for root hubs
Assume that the peer of a superspeed port is the port with the same id
on the shared_hcd root hub.  This identification scheme is required of
external hubs by the USB3 spec [1].  However, for root hubs, tier mismatch
may be in effect [2].  Tier mismatch can only be enumerated via platform
firmware.  For now, simply perform the nominal association.

A new lock 'usb_port_peer_mutex' is introduced to synchronize port
device add/remove with peer lookups.  It protects peering against
changes to hcd->shared_hcd, hcd->self.root_hub, hdev->maxchild, and
port_dev->child pointers.

[1]: usb 3.1 section 10.3.3
[2]: xhci 1.1 appendix D

Cc: Alan Stern <stern@rowland.harvard.edu>
[alan: usb_port_peer_mutex locking scheme]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:38:52 -07:00
Dan Williams
a4204ff0bd usb: cleanup setting udev->removable from port_dev->connect_type
Once usb-acpi has set the port's connect type the usb_device's
->removable attribute can be set in the standard location
set_usb_port_removable().

This also changes behavior in the case where the firmware says that the
port connect type is unknown.  In that case just use the default setting
determined from the hub descriptor.

Note, we no longer pass udev->portnum to acpi_find_child_device() in the
root hub case since:
1/ the usb-core sets this to zero
2/ acpi always expects zero
...just pass zero.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:35:10 -07:00
Dan Williams
d99f6b4130 usb: rename usb_port device objects
The current port name "portX" is ambiguous.  Before adding more port
messages rename ports to "<hub-device-name>-portX"

This is an ABI change, but the suspicion is that it will go unnoticed as
the port power control implementation has been broken since its
introduction.  If however, someone was relying on the old name we can
add sysfs links from the old name to the new name.

Additionally, it unifies/simplifies port dev_printk messages and modifies
instances of:
	dev_XXX(hub->intfdev, ..."port %d"...
	dev_XXX(&hdev->dev, ..."port%d"...
into:
	dev_XXX(&port_dev->dev, ...

Now that the names are unique usb_port devices it would be nice if they
could be included in /sys/bus/usb.  However, it turns out that this
breaks 'lsusb -t'.  For now, create a dummy port driver so that print
messages are prefixed "usb 1-1-port3" rather than the
subsystem-ambiguous " 1-1-port3".

Finally, it corrects an odd usage of sscanf("port%d") in usb-acpi.c.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:35:10 -07:00
Dan Williams
9262c19d14 usb: disable port power control if not supported in wHubCharacteristics
A hub indicates whether it supports per-port power control via the
wHubCharacteristics field in its descriptor.  If it is not supported
a hub will still emulate ClearPortPower(PORT_POWER) requests by
stopping the link state machine.  However, since this does not save
power do not bother suspending.

This also consolidates support checks into a
hub_is_port_power_switchable() helper.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:35:09 -07:00
Alan Stern
600856c231 USB: mutual exclusion for resetting a hub and power-managing a port
The USB core doesn't properly handle mutual exclusion between
resetting a hub and changing the power states of the hub's ports.  We
need to avoid sending port-power requests to the hub while it is being
reset, because such requests cannot succeed.

This patch fixes the problem by keeping track of when a reset is in
progress.  At such times, attempts to suspend (power-off) a port will
fail immediately with -EBUSY, and calls to usb_port_runtime_resume()
will update the power_is_on flag and return immediately.  When the
reset is complete, hub_activate() will automatically restore each port
to the proper power state.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:28:03 -07:00
Konrad Zapalowicz
342a749341 usb: pci_quirks: fix sparse 'symbol not declared' warning
This commit fixes the following sparse warning:

drivers/usb/host/pci-quirks.c:
    - 252: warning: symbol 'usb_hcd_amd_remote_wakeup_quirk' was not
      declared. Should it be static?

This function is exported so the fix was to add it's declaration to the
header file.

Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:25:32 -07:00
Paul Bolle
d30f2065d6 usb: gadget: rename CONFIG_USB_GADGET_PXA25X
Commit 193ab2a607 ("usb: gadget: allow multiple gadgets to be built")
basically renamed the Kconfig symbol USB_GADGET_PXA25X to USB_PXA25X. It
did not rename the related macros in use at that time. Commit
c0a39151a4 ("ARM: pxa: fix inconsistent CONFIG_USB_PXA27X") did so for
all but one macro. Rename that last macro too now.

Fixes: 193ab2a607 ("usb: gadget: allow multiple gadgets to be built")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:25:32 -07:00
Benoit Taine
a328512d3c USB: storage: ene_ub6250: Use kmemdup instead of kmalloc + memcpy
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci

Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:23:44 -07:00
Huang Rui
a7683eb3af usb: usbtest: add pattern check on pipe in phase of unlink read
TEST 11 unlinks the URB read request for N times. When host and gadget
both initialize pattern 1 (mod 63) data series to do IN transfer, the
host side function should check the data buffer if it is as mod 63
series, because the data packet which host receivced will follow
pattern 1. So this patch adds this checking action.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:23:43 -07:00
Huang Rui
e4d58f5dcb usb: usbtest: fix unlink write error with pattern 1
TEST 12 and TEST 24 unlinks the URB write request for N times. When
host and gadget both initialize pattern 1 (mod 63) data series to
transfer, the gadget side will complain the wrong data which is not
expected.  Because in host side, usbtest doesn't fill the data buffer
as mod 63 and this patch fixed it.

[20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last
[20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active
[20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy
[20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete
[20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0
[20285.491431] zero gadget: bad OUT byte, buf[1] = 0
[20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 00000000 00000000 00000000
[20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512
[20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last
[20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0

Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:23:43 -07:00
Marek Szyprowski
657d898a93 usb: usb5303: add support for reference clock specified in device tree
USB3503 chip supports 8 values of reference clock. The value is
specified by REF_SEL[1:0] pins and INT_N line. This patch add support
for getting 'refclk' clock, enabling it and setting INT_N line according
to the value of the gathered clock. If no clock has been specified,
driver defaults to the old behaviour (assuming that clock has been
specified by REF_SEL pins from primary reference clock frequencies
table).

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:19:04 -07:00
Todd E Brandt
6fecd4f2a5 USB: separate usb_address0 mutexes for each bus
This patch creates a separate instance of the usb_address0 mutex for each USB
bus, and attaches it to the usb_bus device struct. This allows devices on
separate buses to be enumerated in parallel; saving time.

In the current code, there is a single, global instance of the usb_address0
mutex which is used for all devices on all buses. This isn't completely
necessary, as this mutex is only needed to prevent address0 collisions for
devices on the *same* bus (usb 2.0 spec, sec 4.6.1). This superfluous coverage
can cause additional delay in system resume on systems with multiple hosts
(up to several seconds depending on what devices are attached).

Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:11:49 -07:00
Denis Turischev
0a939993bf xhci: Switch only Intel Lynx Point-LP ports to EHCI on shutdown.
Patch "xhci: Switch Intel Lynx Point ports to EHCI on shutdown."
commit c09ec25d36 is not fully correct

It switches both Lynx Point and Lynx Point-LP ports to EHCI on shutdown.
On some Lynx Point machines it causes spurious interrupt,
which wake the system: bugzilla.kernel.org/show_bug.cgi?id=76291

On Lynx Point-LP on the contrary switching ports to EHCI seems to be
necessary to fix these spurious interrupts.

Signed-off-by: Denis Turischev <denis@compulab.co.il>
Reported-by: Wulf Richartz <wulf.richartz@gmail.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:11:49 -07:00
Oliver Neukum
c78d1ecfd7 USB: yurex: fix race between probe() and read()
There's a window during which read() would return 0 instead
of a correct error for no data yet. Reorder initialization
to fix the race.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:03:58 -07:00
Oliver Neukum
552e1f2679 USB: appledisplay: fix race between reading and writing from the device
The workqueue handler may call appledisplay_bl_get_brightness() while
user space calls appledisplay_bl_update_status(). As they share a
buffer that must not happen. Use a mutex for mutual exclusion.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:03:57 -07:00
Oliver Neukum
d846b7650d USB: usbtmc: fix DMA on stack
send_request_dev_dep_msg_in() use a buffer allocated on the stack.
Fix by kmalloc()ing the buffer.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:03:57 -07:00
Oliver Neukum
d1b781002b USB: cdc-acm: use BIT macro
Converting the header to BIT for readability. No functional
change.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 16:03:57 -07:00