We need to define _PAGE_FILE macro and change pte
functions. Microblaze use the same MMU as PowerPC
that's why we define _PAGE_FILE in the same style.
This change fixed remap_file_pages01 LTP test.
Signed-off-by: Michal Simek <monstr@monstr.eu>
For 64bits arguments gcc caused that put_user macro
works with wrong value because of optimalization.
Adding volatile caused that gcc not optimized it.
It is possible to use (as Blackfin do) two put_user
macros with 32bits arguments but there is one more
instruction which is due to duplication zero return
value which is called put_user_asm macro.
Signed-off-by: Michal Simek <monstr@monstr.eu>
It is necessary to zeroed r7 when r7 points to bad
dtb - this caused that we have correct messages
about compiled-in dtb or passing via r7
Signed-off-by: Michal Simek <monstr@monstr.eu>
If r7 is zero at kernel boot, or does not point to a valid DTB, then
we fall back to a DTB (assumed to be) linked statically in the kernel, instead
of blindly copying bogus cruft into the kernel DTB memory region
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This fix remove bug which we had till now in all
Microblaze MMU code. Primary tested on mmap01 LTP test.
We forget to flush invalid tlb which were changed - we
used them and there were wrong old data which wasn't correct.
Signed-off-by: Michal Simek <monstr@monstr.eu>
There is an 82599 errata that UDP frames with a zero checksum are
incorrectly marked as checksum invalid by the hardware. This was
leading to misleading hw_csum_rx_error counts. This patch adds a
test around this counter increase for this condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More stuff for http://bugzilla.kernel.org/show_bug.cgi?id=9512
Some 8168 are unable to WoL when receiving is not enabled (plain
old 8169 do not seem to care).
It is not exactly pretty to leave the receiver enabled but we
should now enable DMA late enough for it to be safe. Some late
stage boot failure due to pxe and friends may benefit from the
delayed enabling of bus-mastering as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jaromír Cápík <tavvva@volny.cz>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Reset consumer of status rings to 0 when cleaning
up sw resources. Status rings are not deleted
during suspend since they have napi objects.
This ensures correct rx processing across suspen-resume.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kobject_init_and_add will alloc memory for kobj->name, so in br_add_if
error path, simply use kobject_del will not free memory for kobj->name.
Fix by using kobject_put instead, kobject_put will internally calls
kobject_del and frees memory for kobj->name.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of a static buffer in rose2asc() to return its result is not
threadproof and can result in corruption if multiple threads are trying
to use one of the procfs files based on rose2asc().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
io[i] is read before the bounds check on i, order should be reversed
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
io[i] is read before the bounds check on i, order should be reversed
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
loop bound looks to be wrong, for an array of length 8
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_idx is checked to be < 4, but np->phys[] is 2 elements long
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix/hda:
ALSA: hda - Fix mute control with some ALC262 models
ALSA: hda - Restore GPIO1 properly at resume with AD1984A
ALSA: hda - Use snprintf() to be safer
Allocating new block group is easy when the disk has plenty of space.
But things get difficult as the disk fills up, especially if
the FS has been run through btrfs-vol -b. The balance operation
is likely to make the total bytes available on the device greater
than the largest extent we'll actually be able to allocate.
But the device extent allocation code incorrectly assumes that a device
with 5G free will be able to allocate a 5G extent. It isn't normally a
problem because device extents don't get freed unless btrfs-vol -b
is run.
This fixes the device extent allocator to remember the largest free
extent it can find, and then uses that value as a fallback.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs allocates individual extents from block groups, and each
block group has a specific type. It may hold metadata, data
mirrored or striped etc.
When we balance space (btrfs-vol -b) or remove a drive (btrfs-vol -r)
we free block groups. Once a block group is freed, the space it was
using on the device may be available for use by new block groups.
btrfs_remove_block_group was clearing the flag that said
'our devices are full, don't even try to allocate new block groups',
but it was only clearing that flag for a specific type of block group.
This commit clears the full flag for all of the types of block groups,
making it much more likely that we'll be able to balance space when
the drive is close to full.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The commit_transaction call to wait_ordered_extents when snap_pending
passes nocow_only=1 to process only NOCOW or PREALLOC extents. This isn't
correct for the 'flushoncommit' mode, as it skips extents we just started
IO on in start_delalloc_inodes.
So, in the flushoncommit case, wait on all ordered extents. Otherwise,
only pass the nocow_only flag to wait_ordered_extents if snap_pending.
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When enabling debug with v4l_debug set to 2 or greater, the driver
OOPS's on startup. Checks dev pointer before dereferencing, in
order to prevent this OOPS.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IOCTLS will never get handled if we dont connect
video_ioctl2 to mpeg_fops.ioctl
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both tvaudio and the tuner share i2c address 0x42. The tvaudio module can
check whether it really is a tda9840, but the tuner can't. So the tvaudio
module must be loaded before the tuner module. This was also the case for
2.6.29, but the order was swapped in 2.6.30.
Thanks to Krzysztof Grygiencz for reporting and testing this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent patch didn't take into account that frontends can be compiled into
the kernel. Or that frontends compiled as modules can't be used by the
b2c2 driver if it is not a module itself.
Some frontends require multiple drivers, e.g. a demod driver and a tuner
driver. The code for the frontend support was getting added if the demod
driver was available. Change this to also require any needed tuner or SEC
drivers as well.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is not just pure cosmetic, since the order affects the out-of-tree
module build at the -hg development tree.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Request demodulator auto-detect transmission parameters in case of
garbage parameters provided by application for compatibility.
That's needed at least for MPlayer compatibility currently.
Thanks to Jelle de Jong for reporting issue and providing SSH access to
Devin for debugging.
Thanks to Devin Heitmueller for hard debug work he did to find that bug.
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced when adding the light frequency control
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the change was introduced in the zl10353 for the i2c gate behavior, this
broke the HVR-900 which was not behind a gate. Use a version of the zl10353
config profile that indicates the tuner is not behind such a gate.
Without this patch the first tune succeeds, but subsequent tuning attempts
will fail.
The change also renames the terratec zl10353 profile I wrote to be more
generic, since it is shared by the non-terratec device.
Thanks to Michael Krufky for providing a HVR-900 and DVB-T environment to test
with.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which
is required for digital tuning to work properly. Add the missing profile.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cases where the device has a generic Empia USB ID, the call in the
precard setup phase did not set the tuner GPIO. As a result, the tuner may
not be taken out of reset before attempting initialization in the analog
driver.
This problem was not seen before with the EVGA inDtube, since that particular
board has the analog GPIO setup to include taking the tuner out of reset.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment for the Pinnacle 320e.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set the GPIO properly for the analog side of the Pinnacle Hybrid Pro, or else
the emp202 doesn't get detected properly.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setup the GPIOs properly and enable support for the DVB side of the Pinnacle
Hybrid Pro USB stick.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy walls pointed out that we were passing 0x5d to the TUNER_GO register,
instead of 0x01. Set the register properly (note the code did still work with
the incorrect value, so this does not address a regression).
Thanks to Andy Walls for noticing the issue.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Terratec Cinergy T XS USB can have either a zl10353 or an mt352. Add
support for the MT352 variant.
Thanks to Jelle de Jong for providing a unit to test/debug with.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Depending on the video input format, vinmode/vinctl needs adjustments.
For TV, this is not relevant, since the supported decoders output data
at the same format. However, webcam sensors may have different formats,
so, this needs to be adjusted based on the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to properly estimate fps, mt9v011 sensor driver needs to know
what is the used frequency on the sensor cristal. Adds the proper fields
and initialization code for specifying the cristal frequency.
Also, based on experimentation, it was noticed that the Silvercrest is
outputing data at 7 fps. This means that it should be using a 6.3 MHz
cristal. This information needs to be double checked later, by opening
the device. Anyway, by using this value for xtal, at least now we have
the correct fps report.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since frames per second is a function of cristal frequency, and this is
device-specific, add a function that allows adjusting it, via
subdev->core->s_config callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is possible to adjust the fps rate by changing some register values.
This is function of the connected Xtal at the camera sensor, being a 27
MHz cristal needed, in order to support 640x480 at 30 fps.
For now, it will only calculate the values for fps. Later patches may
introduce V4L2 ioctls, to allow frequency rate adjustments.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
