This patch makes it return -ENODEV if we run out of empty slots in the
probe function. It's unlikely to happen, but it makes the static
checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the resource_size function instead of manually calculating the
resource size. This actually fixes an off-by-one error.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Comment was not updated when tty_insert_flip_string was generalised.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an UART driver for the UART component available as a SOPC (System on
Programmable Chip) component for Altera FPGAs.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an UART driver for the JTAG UART component available as a SOPC
(System on Programmable Chip) component for Altera FPGAs.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a problem in early versions of the FPGA IP.
In certain situations the IP reports that the FIFO is empty, but a byte is
still clocked out. If a flush is done at that point the currently clocked
byte is canceled.
This causes incompatibilities with the upper layers when a port is closed,
it waits until the FIFO is empty and then closes the port. During close
the FIFO is flushed -> the last byte is not sent properly.
Now the FIFO is only flushed if it is reported to be non-empty. Which
makes the currently clocked out byte to finish.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CTS is a read only bit and we are to stop signal RTS if modem line
TIOCM_RTS is not set.
Thanks for suggestions by Richard Röjfors.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Byte accesses for I/O devices in Xilinx IP is going to be less
desired in the future such that the driver is being changed to
use 32 bit accesses.
This change facilitates using the uartlite IP over a PCIe bus
which only allows 32 bit accesses.
Signed-off-by: John Linn <john.linn@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
n_gsm uses skb functions, so it should depend on NET.
n_gsm.c:(.text+0x123d49): undefined reference to `skb_dequeue'
n_gsm.c:(.text+0x123d98): undefined reference to `kfree_skb'
n_gsm.c:(.text+0x123e1e): undefined reference to `skb_pull'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an implementation of GSM 0710 MUX. The implementation currently supports
- Basic and advanced framing (as either end of the link)
- UI or UIH data frames
- Adaption layer 1-4 (1 and 2 via tty, 3 and 4 as skbuff lists)
- Modem and control messages including the correct retry process
- Flow control
and exposes the MUX channels as a set of virtual tty devices including modem
signals. This is an experimental driver.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The BF54xM procs imply the related BF54x define, so no need to check both.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the SPORT MMR defines have been unified, switch over to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than always turn on the SPORT TX interrupt, only do it when we've
actually queued up data for transmission. This avoids useless interrupt
processing.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These were all copied over from the Blackfin UART driver, but they don't
make sense here because these bits are all specific to the Blackfin UART.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Need to initialize the SPORT state rather than using random memory.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Common serial API says we need to grab the port lock before modifying
the port state to prevent inconsistent state between threads.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some people need flow control on their ports, so now boards can support
that via any GPIOs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clarifies command line set up for devices between consoles and early
devices.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver doesn't care about this, but the common serial core wants it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the resources are in the boards files now.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The waiting loop to stop SPORT TX from TX interrupt is too long. This may
block the SPORT RX interrupts and cause the RX FIFO to overflow. So, do
stop sport TX only after the last char in TX FIFO is moved into the shift
register.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We cannot let a 32-bit RX FIFO read be interrupted otherwise a fake RX
underflow error might be generated.
URL: http://blackfin.uclinux.org/gf/tracker/5145
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: misc comment fixes
UBI: fix s/then/than/ typos
UBI: init even if MTD device cannot be attached, if built into kernel
UBI: remove reboot notifier
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
The whole point of making some of the drivers automatically selected
unless 'EMBEDDED' was to handle quirks transparently after their separation
from the generic core.
Over time, some of the later-added quirks grew into more standalone drivers,
implementing non-trivial features a being larger than a few bytes of code.
In addition to that, some of the standalone drivers don't make sense for
99.9% of the users, as they are very specific to rare devices.
Therefore build by default in only those drivers which
- we historically used to support even before quirk separation from the
core code
- are isolated enough and likely to hit quite large portion of the
users anyway (Microsoft, Logitech)
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This saves some more power at the expense of performance.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* nouveau/for-airlied:
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
drm/nv04: Implement missing nv04 PGRAPH methods in software.
drm/nouveau: Use 0x5f instead of 0x9f as imageblit on original NV10.
radeon needs power supply to get correct PM info so select it at the radeon
level not at the kms option.
Signed-off-by: Dave Airlie <airlied@redhat.com>
list reservation was too optimistic about ttm object reservation
and could think that an object reserved by some other process
as reserved by the list reservation which was false. Thus when
unreserving the list it might unreserve object that it didn't
reserved in the list. Sorry if it's hard to follow but this
kind of things are just causing headheck.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes AGP initialization failure with Apple UniNorth bridges due to trying to
ioremap() normal RAM.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Spotted by Scott Bertilson.
Fixes fdo bug 28146.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Mark Marshall <mark.marshall@csr.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
This patch adds the capability to use the usb debug port with the
kernel debugger. It is also still possible to use this functionality
with or without the earlyprintk=dbgpX. It is possible to use the
kgdbwait boot argument to debug very early in the kernel start up code.
There are two ways to use this driver extension with a kernel boot argument.
1) kgdbdbgp=# -- Where # is the number of the usb debug controller
You must use sysrq-g to break into the kernel debugger on another
connection type other than the dbgp.
2) kgdbdbgp=#debugControlNum#,#Seconds#
In this mode, the usb debug port is polled every #Seconds# for
character input. It is possible to use gdb or press control-c to
break into the kernel debugger.
From the implementation perspective there are 3 high level changes.
1) Allow variable retries for the the hardware via dbgp_bulk_read().
The amount of retries for the dbgp_bulk_read() needed to be
variable instead of fixed. We do not want to poll at all when the
kernel is operating in interrupt driven mode. The polling only
occurs if the kernel was booted when specifying some number of
seconds via the kgdbdbgp boot argument (IE kgdbdbgp=0,1). In this
case the loop count is reduced to 1 so as introduce the smallest
amount of latency as possible.
2) Save the bulk IN endpoint address for use by the kgdb code.
3) The addition of the kgdb interface code.
This consisted of adding in a character read function for the dbgp
as well as a polling thread to allow the dbgp to interrupt the
kernel execution. The rest is the typical kgdb I/O api.
CC: Eric Biederman <ebiederm@xmission.com>
CC: Yinghai Lu <yhlu.kernel@gmail.com>
CC: linux-usb@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
The ekgdboc= differs from kgdboc= in that you can begin debuggin as
soon as the exceptions are setup and the kgdb I/O driver is available,
instead of waiting until the tty subsystem is available.
CC: kgdb-bugreport@lists.sourceforge.net
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
If kdb is open on a serial port that is not actually a console make
sure to call the poll routines to emit and receive characters.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Martin Hicks <mort@sgi.com>
This patch adds in the kdb PS/2 keyboard driver. This was mostly a
direct port from the original kdb where I cleaned up the code against
checkpatch.pl and added the glue to stitch it into kgdb.
This patch also enables early kdb debug via kgdbwait and the keyboard.
All the access to configure kdb using either a serial console or the
keyboard is done via kgdboc.
If you want to use only the keyboard and want to break in early you
would add to your kernel command arguments:
kgdboc=kbd kgdbwait
If you wanted serial and or the keyboard access you could use:
kgdboc=kbd,ttyS0
You can also configure kgdboc as a kernel module or at run time with
the sysfs where you can activate and deactivate kgdb.
Turn it on:
echo kbd,ttyS0 > /sys/module/kgdboc/parameters/kgdboc
Turn it off:
echo "" > /sys/module/kgdboc/parameters/kgdboc
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Allow kgdboc to work on sparc hardware with the Zilog serial chips.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
The sci_poll_get_char() needs to return immediately if there is no
input from the chip to process, and must return a value of
NO_POLL_CHAR.
This allows kgdboc to process multiple polled devices while kgdb is
active.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
The design of the kdb shell requires that every device that can
provide input to kdb have a polling routine that exits immediately if
there is no character available. This is required in order to get the
page scrolling mechanism working.
Changing the kernel debugger I/O API to require all polling character
routines to exit immediately if there is no data allows the kernel
debugger to process multiple input channels.
NO_POLL_CHAR will be the return code to the polling routine when ever
there is no character available.
CC: linux-serial@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'viafb-next' of git://git.lwn.net/linux-2.6: (35 commits)
viafb: move some include files to include/linux
viafb: Eliminate some global.h references
viafb: get rid of i2c debug cruft
viafb: fold via_io.h into via-core.h
viafb: Fix initialization error paths
viafb: Do not remove gpiochip under spinlock
viafb: make procfs entries optional
viafb: fix proc entry removal
viafb: improve misc register handling
viafb: replace inb/outb
viafb: move some modesetting functions to a seperate file
viafb: unify modesetting functions
viafb: Reserve framebuffer memory for the upcoming camera driver
viafb: Add a simple VX855 DMA engine driver
viafb: Add a simple interrupt management infrastructure
via: Rationalize vt1636 detection
viafb: Introduce viafb_find_i2c_adapter()
via: Do not attempt I/O on inactive I2C adapters
viafb: Turn GPIO and i2c into proper platform devices
viafb: Convert GPIO and i2c to the new indexed port ops
...
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Length field of header was incorrectly set to available payload space
rather than the actual payload size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (static per-port,
singleton(!) urb pool).
Also remove changelog header (can be retrieved through git).
Read processing and write-buffer handling tested using a cp210x device
in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Private data was not freed on error path in startup.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up read processing logic.
Tested using a cp210x device in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom single-urb write implementation.
Note that this driver still depended on the write callback from the old
generic framework.
Tested against original read processing using a cp210x device in a
loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Right now quirks are printed only when the are manually overriden with
the module parameters. It's not so useful to remind the user that his
parameters are correctly applied; what is useful is to print out the
quirks the user is not aware are being applied.
So let's do the smart thing and print the quirks when they are present.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use pr_foo and dev_foo instead of printk. Maybe US_DEBUG* should be
replaced too.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill private write fifo and use port fifo instead (protected under
port lock).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo implementation.
Use private write fifo to minimise changes to lock handling.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo implementation.
Note that cypress_m8 has no port write fifo as it has no bulk-out
endpoint.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use bulk_out_size in usb_serial_driver to set urb buffer size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the bulk-out buffer size to avoid any regression in throughput
after replacing the old writing scheme which used dynamic buffers (e.g.
up to 2k).
256b has been determined to be a good choice for several drivers
including ftdi_sio which used to have a more or less identical write
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use process_read_urb to implement line status handling.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (dynamically allocated write
urbs).
Note that I chose to remove the stat module parameter which was supposed
to keep count of the amount of data sent and received, but which has
been broken for three years (since b308e74d9c
"USB: visor driver adapted to new tty buffering" -- bytes_in was
incorrectly updated and was thus always reported as 0).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix memory leak for some devices (Sony Clie 3.5) due to port private
data not being freed on release.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo, read and write implementations (single-urb and fifo,
but still maintained list of 256*256b urb buffers per port).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (static 16*4k write-urb pool
shared among all ports in system).
Also remove old changelog entries in header (code is now gone, and
these entries can still be retrieved through git).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return immediately from generic process_read_urb if urb is empty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An urb transfer buffer is allocated at every open but was never freed.
This driver is a bit of a mess...
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for an olivetti olicard100 HЅDPA usb-stick.
This device is a zeroCD one with ID 0b3c:c700 that needs switching via
eject or usb-modeswitch with
MessageContent="5553424312345678000000000000061b000000030000000000000000000000".
After switching it has ID 0b3c:c000 and provides 5 serial ports ttyUSB[0-4].
Port 0 (modem) and 4 are interrupt ports.
Signed-off-by: Nils Radtke <lkml@Think-Future.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_find_device was the only one user of match_device, now
it is removed, so remove match_device to fix the compile warning
below reported by Stephen Rothwell:
drivers/usb/core/usb.c:596: warning: 'match_device'
defined but not used
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 7acd72eb85 ("kfifo: rename
kfifo_put... into kfifo_in... and kfifo_get... into kfifo_out..."),
kfifo_out() is marked __must_check, and that causes gcc to produce
lots of warnings like this:
CC drivers/usb/host/fhci-mem.o
In file included from drivers/usb/host/fhci-hcd.c:34:
drivers/usb/host/fhci.h: In function 'cq_get':
drivers/usb/host/fhci.h:520: warning: ignoring return value of 'kfifo_out', declared with attribute warn_unused_result
...
This patch fixes the issue by properly checking the return value.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: stable <stable@kernel.org> [.33 and .34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove cp210x_disconnect which is used to kill traffic although this is
already handled by the generic framework.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No need to raise dtr/rts in open as this is taken care of by tty layer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use dynamically allocated urb for baudrate changes rather than
unconditionally submitting the port write urb which may already be in
use.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use usb_serial_driver bulk_in_size and bulk_out_size to make sure
buffers of appropriate sizes are allocated in the first place rather than
reallocating them at every open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the user specifies a custom bulk buffer size we get a double free at
port release.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1380) fixes a bug in the wakeup settings for EHCI host
controllers. When the controller is suspended, if it isn't enabled
for remote wakeup then we have to turn off all the port wakeup flags.
Disabling PCI PME# isn't good enough, because some systems (Intel)
evidently use alternate wakeup signalling paths.
In addition, the patch improves the handling of the Intel Moorestown
hardware by performing various power-up and power-down delays just
once instead of once for each port (i.e., the delays are moved outside
of the port loops). This requires extra code, but the total delay
time is reduced.
There are also a few additional minor cleanups.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Ondrej Zary <linux@rainbow-software.org>
CC: Alek Du <alek.du@intel.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a bug fix for PHCD (phy clock disable) low power feature:
After PHCD is set, any write to PORTSC register is illegal, so when
resume ports, clear PHCD bit first.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Our virtual xHCI device can have as many ports as we like - I've tested
this patch with 31.
Signed-off-by: William Gulland <wgulland@vmware.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now on one uses this function and it seems useless,
so remove usb_find_device.
[tom@tom linux-2.6-next]$ grep -r -n -I usb_find_device ./
drivers/media/dvb/dvb-usb/dvb-usb-init.c:160:static struct
dvb_usb_device_description * dvb_usb_find_device(struct usb_device
*udev,struct dvb_usb_device_properties *props, int *cold)
drivers/media/dvb/dvb-usb/dvb-usb-init.c:230: if ((desc =
dvb_usb_find_device(udev,props,&cold)) == NULL) {
drivers/usb/core/usb.c:630: * usb_find_device - find a specific usb device in the system
drivers/usb/core/usb.c:642:struct usb_device *usb_find_device(u16 vendor_id, u16 product_id)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In to places in fsg_common_init() an unconditional call to kfree()
on common was performed in error recovery which is not a valid
behaviour since fsg_common structure is not always allocated by
fsg_common_init().
To fix, the calls has been replaced with a goto to a proper error
recovery which does the correct thing.
Also, refactored fsg_common_release() function.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Viral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Obviously, {} is needed in the branch of
"else if (hcd->driver->flags & HCD_LOCAL_MEM)"
for handling of setup packet mapping.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An undocumented "feature" in the OMAP3 EHCI controller causes
suspended ports to be taken out of suspend when the USBCMD.Run/Stop
bit is cleared (this bit is normally cleared when ehci_bus_suspend
is called).
This "feature" breaks suspend-resume if the root-hub is allowed
to suspend. (The controller thinks it is in resume, and the PHY
thinks it is still in suspend).
There is an undocumented register bit that can be used to disable
this feature and restore normal behavior. Set this bit so
suspend-resume can work normally.
Tested on OMAP3 SDPs with the NXP ISP1504 and NXP ISP1703 PHYs.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1379) reworks the logic for handling USB interface
runtime-PM settings -- hopefully it's right this time! The problem is
that when a driver is unbound or binding fails, runtime PM for the
interface always gets disabled. But pm_runtime_disable() nests, so it
shouldn't be called unless the interface was previously enabled for
runtime PM.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Rob Duncan <Robert.Duncan@exar.com>
Tested-by: Rob Duncan <Robert.Duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change transfer ring behavior to not follow/activate link TRBs
until active TRBs are queued after it. This change affects
the behavior when a TD ends just before a link TRB.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix g_ffs build error, add a needed header file:
drivers/usb/gadget/f_fs.c:1064:error: 'PAGE_CACHE_SIZE' undeclared (first use in this function)
drivers/usb/gadget/f_fs.c:1065:error: 'PAGE_CACHE_SHIFT' undeclared (first use in this function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On OMAP systems, we have two different OHCI controllers. The legacy
one is present in OMAP1/2 chips, and the newer one comes bundled as
a companion to the EHCI controller on OMAP3 and newer chips.
We may have multi-omap configurations where OMAP2 and OMAP3
support may be enabled in the same kernel, and need a mechanism
to keep both drivers around.
This patch adds a Kconfig entry for each of these drivers.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the OHCI controller present in OMAP3 and newer chips.
The code is mostly based off the ehci-omap.c driver.
Some of it is common to both drivers and will eventually
need to be factored out to platform init files.
In its current state, the driver cannot co-exist with the ehci-omap
driver, and this will be fixed in later versions. The second driver
to be loaded will overwrite settings made by the other. For now,
this driver should allow the few users of OMAP3 OHCI to get going.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renamed fsl_mx3_udc.c -> fsl_mxc_udc.c
for mx51, usb core is clocked from sources that are not 60mhz.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reverse priority of errors reported to ldisc so that it matches that of
other serial drivers (break takes precedence over parity, which takes
precedence over framing errors).
Also make sure overrun errors are handled as in other drivers, that is,
an overrun error is always reported and is not associated with any
received character (instead a NULL character with the TTY_OVERRUN flag
set is inserted).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use tty_insert_flip_string_fixed_flag to report errors to line
discipline.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use tty_insert_flip_string_fixed_flag to report errors to line
discipline.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were some reports[1] of isp1760 USB driver malfunctioning
with high speed devices, noticed on Blackfin and PowerPC targets.
These reports indicated that the original Philips 'pehcd'[2]
driver worked fine.
We've noticed the same issue with an ARM RealView platform. This
happens under load (with only some mass storage devices, not all,
just as in another report[3]):
error bit is set in DW3
error bit is set in DW3
error bit is set in DW3
usb 1-1.2: device descriptor read/64, error -32
It appears that the 'pehcd' driver checks the X bit only if the
transaction is halted (H bit), otherwise the error is so far
insignificant.
The ISP176x chips were modeled after EHCI, and EHCI spec says
(thanks to Alan Stern for pointing out):
"Transaction errors cause the status field to be updated to reflect
the type of error, but the transaction continues to be retried until
the Active bit is set to 0. When the error counter reaches 0, the
Halt bit is set and the Active bit is cleared."
So, just as the original Philips driver, isp1760 must report the
error only if the transaction error and the halt bits are set.
[1] http://markmail.org/message/lx4qrlbrs2uhcnly
[2] svn co svn://sources.blackfin.uclinux.org/linux-kernel/trunk/drivers/usb/host -r 5494
See pehci.c:pehci_hcd_update_error_status().
[3] http://blackfin.uclinux.org/gf/tracker/5148
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When USB3 protocol port detects an USB3.0 device attach, the port will
automatically transition to the Enabled state upon the completion
of successful link training.
Do not disable USB3 protocol ports in hub_activate(), or USB3.0 device
will fail to be recognized if xHCI bus power management is implemented.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix regression introduced by commit
a108bfcb37 (USB: tty: Prune uses of
tty_request_room in the USB layer) which broke three drivers
(cypress_m8, digi_acceleport and spcp8x5) through incorrect use of
tty_insert_flip_string_fixed_flag.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch that makes sure that the device ID data (idVendor,
idProduct and bcdDevice) are assigned to the descriptor in the cdev
structure *before* the composite gadget starts binding. This allows the
composite driver, and all the composite functions it uses, access to
that data.
In one of the composite functions we created, we needed to register an
input device and wanted to use the idVendor, idProduct and bcdDevice
codes to properly initialize the id field of the input device. We could
not do that because the idVendor, idProduct and bcdDevice values were
only set in the cdec structure *after* the composite->bind(cdev) call.
Signed-off-by: Robert Lukassen <robert.lukassen@tomtom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After using state stored in xhci_virt_ep to clean up a stalled endpoint,
be sure to set the stalled stream ID back to 0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Function Filesystem (FunctioFS) lets one create USB
composite functions in user space in the same way as GadgetFS
lets one create USB gadgets in user space. This allows
creation of composite gadgets such that some of the functions
are implemented in kernel space (for instance Ethernet, serial
or mass storage) and other are implemented in user space.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The FunctionFS is a USB composite function that can be used
with the composite framework to create an USB gadget.
>From kernel point of view it is just a composite function with
some unique behaviour. It may be added to an USB
configuration only after the user space driver has registered
by writing descriptors and strings (the user space program has
to provide the same information that kernel level composite
functions provide when they are added to the configuration).
>From user space point of view it is a file system which when
mounted provide an "ep0" file. User space driver need to
write descriptors and strings to that file. It does not need
to worry about endpoints, interfaces or strings numbers but
simply provide descriptors such as if the function was the
only one (endpoints and strings numbers starting from one and
interface numbers starting from core). The FunctionFS changes
numbers of those as needed also handling situation when
numbers differ in different configurations.
When descriptors and strings are written "ep#" files appear
(one for each declared endpoint) which handle communication on
a single endpoint. Again, FunctionFS takes care of the real
numbers and changing of the configuration (which means that
"ep1" file may be really mapped to (say) endpoint 3 (and when
configuration changes to (say) endpoint 2)). "ep0" is used
for receiving events and handling setup requests.
When all files are closed the function disables itself.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__init, __initdata and __exit tags have have been removed from
various files to make it possible for gadgets that do not use
the __init/__exit tags to use those.
Files in question are related to:
* the core composite framework,
* the mass storage function (fixing a section mismatch) and
* ethernet driver (ACM, ECM, RNDIS).
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove multi-urb write from the generic driver and simplify the
prepare_write_buffer prototype:
int (*prepare_write_buffer)(struct usb_serial_port *port,
void *dest, size_t size);
The default implementation simply fills dest with data from port write
fifo but drivers can override it if they need to process the outgoing
data (e.g. add headers).
Turn ftdi_sio into a generic fifo-based driver, which lowers CPU usage
significantly for small writes while retaining maximum throughput.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reimplement fifo-based writes in the generic driver using a multiple
pre-allocated urb scheme.
In contrast to multi-urb writes, no allocations (of urbs or buffers) are
made during run-time and there is less pressure on the host stack
queues as currently only two urbs are used (implementation is generic
and can handle more than two urbs as well, though).
Initial tests using ftdi_sio show that the implementation achieves the
same (maximum) throughput at high baudrates as multi-urb writes. The CPU
usage is much lower than for multi-urb writes for small write requests
and only slightly higher for large (e.g. 2k) requests (due to extra copy
via fifo?).
Also outperforms multi-urb writes for small write requests on an
embedded arm-9 system, where multi-urb writes are CPU-bound at high
baudrates (perf reveals that a lot of time is spent in the host stack
enqueue function -- could perhaps be a bug as well).
Keeping the original write_urb, buffer and flag for now as there are
other drivers depending on them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill circular buffers for tx and rx as well as read work thread, and
switch to generic kfifo-based write implementation.
This is an example of how prepare_write_buffer and process_read_urb can
be used to handle protocols with packet headers.
Please note the diffstat which shows that the same functionality is now
provided using only a tenth of the code (including whitespace and
comments, though).
Tested-by: Naranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original SIO devices require a control byte for every packet
written. Clean up the unnecessarily messy implementation of this.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch to the generic, multi-urb, write implementation.
Note that this will also make it fairly easy to use the generic
fifo-based write implementation: simply unset the multi_urb_write flag
and modify prepare_write_buffer (or unset if not using a legacy SIO
device). This may be desirable for instance on an embedded system where
optimal throughput at high baudrates may not be as important as other
factors (e.g. no allocations during runtime and less pressure on host
stack).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one
errors.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1377) simplifies the code in usb_sg_init(), without
changing its functionality. It also removes a couple of unused fields
from the usb_sg_request structure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This webcam gadget instantiates a UVC camera (360p and 720p resolutions
in YUYV and MJPEG).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This USB video class function driver implements a video capture device from the
host's point of view. It creates a V4L2 output device on the gadget's side to
transfer data from a userspace application over USB.
The UVC-specific descriptors are passed by the gadget driver to the UVC
function driver, making them completely configurable without any modification
to the function's driver code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the type of the URB's 'sg' pointer from a usb_sg_request to
a scatterlist. This allows drivers to submit scatter-gather lists
without using the usb_sg_wait() interface. It has the added benefit
of removing the typecasts that were added as part of patch as1368 (and
slightly decreasing the number of pointer dereferences).
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converting a pipe number to a struct usb_host_endpoint pointer is a little
messy. Introduce a new convenience function to hide the mess.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qset_print() was not declared static although it is not used
outside of debug.c
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These Appotech controllers are found in Picture Frames, they provide a
(buggy) emulation of a cdrom drive which contains the windows software
Uploading of pictures happens over the corresponding /dev/sg device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The max packet length bit mask used for isochronous endpoints
should be 0x7FF instead of 0x8FF. 0x8FF will actually clear
higher-order bits in the max packet length field.
This patch applies to 2.6.34-rc6.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AM3517 is based on ES3.1 thus ES2.x related programming is invalid
for it so updating ES2.x programming.
Also fixed below checkpatch warning:
WARNING: unnecessary whitespace before a quoted newline
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes below compilation warning:
drivers/usb/host/ehci-hcd.c:425:
warning: 'ehci_port_power' defined but not used
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another CDC-ACM + vendor specific interface layout.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
