In commit f0fba2ad (ASoC: multi-component - ASoC Multi-Component
Support), the name of the ak4104 codec driver was changed without
amending the platform code which uses it as well.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The display requires some milliseconds between GPIO_TFT_VA_EN
and GPIO_DISPLAY_ENABLE. Reorder initialisation to comply with
the display spec.
Also tune timings for better compliance with the spec.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The backlight control is going to change back to PWM in the
upcoming Raumfeld Controller hardware revision.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The PXA platform code has a static inline helper called
gpio_to_chip which clashes with the gpiolib namespace if we
try to expose the function with the same name from gpiolib,
and it's still confusing even if we don't do that. So rename
it to gpio_to_pxachip().
Reported-by: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This platform has not been converted to 'struct irq_data' when the big
pile was done. It fails to compile nowadays, because the compatibility
code has gone.
CC arch/arm/mach-vt8500/irq.o
arch/arm/mach-vt8500/irq.c:118:2: error: unknown field 'ack' specified in initializer
arch/arm/mach-vt8500/irq.c:118:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:119:2: error: unknown field 'mask' specified in initializer
arch/arm/mach-vt8500/irq.c:119:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:120:2: error: unknown field 'unmask' specified in initializer
arch/arm/mach-vt8500/irq.c:120:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:121:2: error: unknown field 'set_type' specified in initializer
arch/arm/mach-vt8500/irq.c:121:2: warning: initialization from incompatible pointer type
make[1]: *** [arch/arm/mach-vt8500/irq.o] Error 1
Add the missing conversion. Tested on a JayPC-Tablet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alexey Charkov <alchark@gmail.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The original pair of <0x01db, 208000000> is invalid. Correct it to
the valid value.
The 6th bit of the NFC APMU register indicates NFC works whether
at 156Mhz or 78Mhz. So 0x19b indicates NFC works at 156Mhz, and
0x1db indicates it works at 78Mhz.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The original pair of <0x01db, 208000000> is invalid.
Correct to the valid value.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The file mfp-pxa2xx.c defines a macro, PGSR(), which translates a gpio
bank number to a PGSR register address. The function pxa2xx_mfp_suspend()
erroneously passed in a gpio number instead of a gpio bank number.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'at91/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc:
AT91: Change nand buswidth logic to match hardware default configuration
at91: Use "pclk" as con_id on at91cap9 and at91rm9200
at91: fix udc, ehci and mmc clock device name for cap9/9g45/9rl
atmel_serial: fix internal port num
at91: fix at91_set_serial_console: use platform device id
The recently modified nand buswitth configuration is not aligned with
board reality: the double footprint on boards is always populated with 8bits
buswidth nand flashes.
So we have to consider that without particular configuration the 8bits
buswidth is selected by default.
Moreover, the previous logic was always using !board_have_nand_8bit(), we
change it to a simpler: board_have_nand_16bit().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Use the INT_SRC_OVR IRQ (instead of GSI) to preset the ACPI SCI IRQ.
xen/mmu: Fix for linker errors when CONFIG_SMP is not defined.
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
sh: use printk_ratelimited instead of printk_ratelimit
sh: Fix up unmet dependency warnings with USB EHCI/OHCI selects.
sh: fix the value of sh_dmae_slave_config in setup-sh7757
sh: fix the INTC vector for IRQ and IRL in setup-sh7757
sh: add to select the new configuration for USB EHCI/OHCI
sh: add platform_device of EHCI/OHCI to setup-sh7757
sh: fix compile error using sh7757lcr_defconfig
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
ARM: mach-shmobile: make a struct in board-ap4evb.c static
ARM: mach-shmobile: ag5evm: consistently name sdhi info structures
ARM: mach-shmobile: mackerel: change usbhs devices order
In the past we would use the GSI value to preset the ACPI SCI
IRQ which worked great as GSI == IRQ:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
While that is most often seen, there are some oddities:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
which means that GSI 20 (or pin 20) is to be overriden for IRQ 9.
Our code that presets the interrupt for ACPI SCI however would
use the GSI 20 instead of IRQ 9 ending up with:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=20
xen: acpi sci 20
.. snip..
calling acpi_init+0x0/0xbc @ 1
ACPI: SCI (IRQ9) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20110413/evevent-119)
ACPI: Unable to start the ACPI Interpreter
as the ACPI interpreter made a call to 'acpi_gsi_to_irq' which got nine.
It used that value to request an IRQ (request_irq) and since that was not
present it failed.
The fix is to recognize that for interrupts that are overriden (in our
case we only care about the ACPI SCI) we should use the IRQ number
to present the IRQ instead of the using GSI. End result is that we get:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=9 (gsi=9)
xen: acpi sci 9
which fixes the ACPI interpreter failing on startup.
CC: stable@kernel.org
Reported-by: Liwei <xieliwei@gmail.com>
Tested-by: Liwei <xieliwei@gmail.com>
[http://lists.xensource.com/archives/html/xen-devel/2011-06/msg01727.html]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Simple enough - we use an extern defined symbol which is not
defined when CONFIG_SMP is not defined. This fixes the linker
dying.
CC: stable@kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
struct soc_camera_link imx074_link in board-ap4evb.c doesn't have
to be global.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
arch/powerpc: use printk_ratelimited instead of printk_ratelimit
powerpc/rtas-rtc: remove sideeffects of printk_ratelimit
powerpc/pseries: remove duplicate SCSI_BNX2_ISCSI in pseries_defconfig
powerpc/e500: fix breakage with fsl_rio_mcheck_exception
powerpc/p1022ds: fix audio-related properties in the device tree
powerpc/85xx: fix NAND_CMD_READID read bytes number
Fix the value of chcr for SCIF[2-4]_RX and RIIC[0-9]_RX and
the value of mid_rid for some RIIC.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
%rip-relative addressing is relative to the first byte of the next instruction,
so we need to add %rip only after we've fetched any immediate bytes.
Based on original patch by Li Xin <xin.li@intel.com>.
Signed-off-by: Avi Kivity <avi@redhat.com>
Acked-by: Li Xin <xin.li@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Don't use printk_ratelimit() as an additional condition for returning
on an error. Because when the ratelimit is reached, printk_ratelimit
will return 0 and e.g. in rtas_get_boot_time won't check for an error
condition.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove duplicate assignment of SCSI_BNX2_ISCSI in pseries_defconfig
introduced by:
37e0c21e powerpc/pseries: Enable iSCSI support for a number of cards
causes warning:
arch/powerpc/configs/pseries_defconfig:151:warning: override: reassigning to symbol SCSI_BNX2_ISCSI
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
amba pl011: platform data for reg lockup and glitch v2
amba pl011: workaround for uart registers lockup
tty: n_gsm: improper skb_pull() use was leaking framed data
tty: n_gsm: Fixed logic to decode break signal from modem status
TTY: ntty, add one more sanity check
TTY: ldisc, do not close until there are readers
8250: Fix capabilities when changing the port type
8250_pci: Fix missing const from merges
ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
serial: ioremap warning fix for jsm driver.
8250_pci: add -ENODEV code for Intel EG20T PCH
Trying to build the Intel SCU Watchdog fails for me with gcc 4.6.0 -
$ gcc --version | head -n 1
gcc (GCC) 4.6.0 20110513 (prerelease)
like this :
CC drivers/watchdog/intel_scu_watchdog.o
In file included from drivers/watchdog/intel_scu_watchdog.c:49:0:
/home/jj/src/linux-2.6/arch/x86/include/asm/apb_timer.h: In function ‘apbt_time_init’:
/home/jj/src/linux-2.6/arch/x86/include/asm/apb_timer.h:65:42: warning: ‘return’ with a value, in function returning void [enabled by default]
drivers/watchdog/intel_scu_watchdog.c: In function ‘intel_scu_watchdog_init’:
drivers/watchdog/intel_scu_watchdog.c:468:2: error: implicit declaration of function ‘sfi_get_mtmr’ [-Werror=implicit-function-declaration]
drivers/watchdog/intel_scu_watchdog.c:468:32: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
make[1]: *** [drivers/watchdog/intel_scu_watchdog.o] Error 1
make: *** [drivers/watchdog/intel_scu_watchdog.o] Error 2
Additionally, linux/types.h is needlessly being included twice in
drivers/watchdog/intel_scu_watchdog.c
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
To make SLUB work on UML we need this_cpu_cmpxchg from
asm-generic/percpu.h.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 21a3c96 uses node_start/end_pfn(nid) for detection start/end
of nodes. But, it's not defined in linux/mmzone.h but defined in
/arch/???/include/mmzone.h which is included only under
CONFIG_NEED_MULTIPLE_NODES=y.
Then, we see
mm/page_cgroup.c: In function 'page_cgroup_init':
mm/page_cgroup.c:308: error: implicit declaration of function 'node_start_pfn'
mm/page_cgroup.c:309: error: implicit declaration of function 'node_end_pfn'
So, fixiing page_cgroup.c is an idea...
But node_start_pfn()/node_end_pfn() is a very generic macro and
should be implemented in the same manner for all archs.
(m32r has different implementation...)
This patch removes definitions of node_start/end_pfn() in each archs
and defines a unified one in linux/mmzone.h. It's not under
CONFIG_NEED_MULTIPLE_NODES, now.
A result of macro expansion is here (mm/page_cgroup.c)
for !NUMA
start_pfn = ((&contig_page_data)->node_start_pfn);
end_pfn = ({ pg_data_t *__pgdat = (&contig_page_data); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});
for NUMA (x86-64)
start_pfn = ((node_data[nid])->node_start_pfn);
end_pfn = ({ pg_data_t *__pgdat = (node_data[nid]); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});
Changelog:
- fixed to avoid using "nid" twice in node_end_pfn() macro.
Reported-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] allow setting of upper 32 bit in smp_ctl_set_bit
[S390] hwsampler: Set a sane default sampling rate
[S390] s390: enforce HW limits for the initial sampling rate
[S390] kvm-s390: fix kconfig dependencies
Hello,
I am not 100% sure this is the right thing to do, but it makes the
atmel-ssc driver happy on my at91rm9200 board.
This unifies the con_id across all at91 machines.
The atmel-ssc driver expects the con_id to be "pclk" or it will fail probing.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI/ACPI: fix type mismatch
PCI: fix new kernel-doc warning
PCI: Fix warning in drivers/pci/probe.c on sparc64
Because the USB EHCI/OHCI driver has new configuration for SH,
the patch enables the EHCI and/or OHCI driver of the on-chip for
some CPUs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ensure that the TLS register is saved and restored over a suspend
cycle, so that userspace programs don't see a corrupted TLS value.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the missing suspend/resume pointers for the suspend code. This
is needed when building for multiple CPUs.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bit shift operation in smp_ctl_set_bit does not specify the type
of the shifted bit so integer is used as default. Therefore it is not
possible to set bits in the upper 32 bit of the control register if
the kernel runs in 64 bit mode. Fix this by specifying the type as
unsigned long.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sampling interval for the hardware sampler is specified in cycles.
(see SA23-2260-01 The Load-Program-Parameter and the CPU-Measurement
Facilities)
The current default value will therefore result in millions of samples.
This patch changes the default sampling interval to 4M, which will
result in ~1500 samples per second on a z196 reducing the overhead
of sampling.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On specific configurations with hwsampler opcontrol --start returns an
error on "echo 1 >/dev/oprofile/enable". Turns out that the hw sampling
interval is not checked against the hardware limits.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A user can create the Kconfig combination !VIRTUALIZATION, S390_GUEST
which results in the following warnings:
warning: (S390_GUEST) selects VIRTIO which has unmet direct dependencies (VIRTUALIZATION)
warning: (S390_GUEST && VIRTIO_PCI && VIRTIO_BALLOON) selects VIRTIO_RING which has unmet direct dependencies (VIRTUALIZATION && VIRTIO)
warning: (S390_GUEST) selects VIRTIO which has unmet direct dependencies (VIRTUALIZATION)
warning: (S390_GUEST && VIRTIO_PCI && VIRTIO_BALLOON) selects VIRTIO_RING which has unmet direct dependencies (VIRTUALIZATION && VIRTIO)
S390_GUEST has to select VIRTUALIZATION before selecting VIRTIO and
friends.
Reported-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The wrong MCSR bit was being used on e500mc. MCSR_BUS_RBERR only exists
on e500v1/v2. Use MCSR_LD on e500mc, and remove all MCSR checking
in fsl_rio_mcheck_exception as we now no longer call that function
if the appropriate bit in MCSR is not set.
If RIO support was enabled at compile-time, but was never probed, just
return from fsl_rio_mcheck_exception rather than dereference a NULL
pointer.
TODO: There is still a remaining, though comparitively minor, issue in
that this recovery mechanism will falsely engage if there's an unrelated
MCSR_LD event at the same time as a RIO error.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the Freescale P1022DS reference board, the SSI audio controller is
connected in "asynchronous" mode to the codec's clocks, so the device tree
needs an "fsl,ssi-asynchronous" property.
Also remove the clock-frequency property from the wm8776 node, because
the clock is enabled only if U-Boot enables it, and U-Boot will set the
property if the clock is enabled. A future version of the P1022DS audio
driver will configure the clock itself, but for now, the driver should
not be told that the clock is running when it isn't.
Also fix the FIFO depth to 15, instead of 16.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MN10300's asm/uaccess.h needs to #include linux/kernel.h to get might_sleep()
otherwise it fails to build on MN10300 allyesconfig. This fails in a few
places with messages like the following:
In file included from security/keys/trusted.c:14:
include/linux/uaccess.h: In function '__copy_from_user_nocache':
include/linux/uaccess.h:52: error: implicit declaration of function 'might_sleep'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The iop13xx_defconfig didn't build since the platform code uses
defines from <asm/ptrace.h>. Simply add the include so it
compiles.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
