Commit graph

28 commits

Author SHA1 Message Date
Matt Sealey
2c8a5dcaa4 regulator: mc13892: sanity check num_regulators parsed vs. registered
Imagine a situation where a device tree has a few regulators in an
appropriate node:

regulators {
	sw1 {
		..
	};

	vvideo {
		..
	};

	:

	vfake {
		..
	};

	vtypo {
		..
	};
};

In the above example, the node name "vfake" is an attempt to match a
regulator name inside the driver which just so happens to not exist. The
node name "vtypo" represents an accidental typographical error in a
regulator name which may have been introduced to a device tree.

In these cases, the number of regulators the mc13892 driver thinks it has
does not match the number of regulators it parsed and registered. Since
it will go over this array based on this number, it will actually
re-register regulator "0" (which happens to be SW1) over and over
again until it reaches the number, resulting in messages on the kernel
log such as these:

SW1: at 1100 mV
VVIDEO: at 2775mV
:
SW1: at 1100 mV
SW1: at 1100 mV

.. up to that number of "mismatched" regulators. Nobody using DT can/will
consume these regulators, so it should not be possible for it to cause any
real regulator problems or driver breakages, but it is an easy thing to
miss in a kernel log and is an immediate indication of a problem with the
device tree authoring.

This patch effectively sanity checks the number of counted children of
the regulators node vs. the number that actually matched driver names,
and sets the appropriate num_regulators value. It also gives a little
warning for device tree authors that they MAY have screwed something up,
such that this patch does not hide the device tree authoring problem.

Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Tested-by: Steev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-27 11:22:30 +08:00
Matt Sealey
ccf3ed782a regulator: mc13892-regulator: correct/refine handling of the SWxHI bit
MC13892 PMIC supports a "HI" bit for 3 of it's 4 buck switcher outputs,
which enables a higher set of voltage ranges.

Despite a comment in the code ('sw regulators need special care due to the
"hi" bit'), it actually does not take special care since it does not modify
it's use of the selector table index when this bit is set, giving us very
odd behavior when setting a high voltage on supported switchers or listing
current voltages. Net effect is in best case the kernel and sysfs report
lower voltages than are actually set in hardware (1300mV instead of 1800mV
for example) and in the worst case setting a voltage (e.g. 1800mV) will cause
an undervoltage condition (e.g. 1300mV).

Correct the behavior, taking into account SW1 doesn't support the HI bit,
and as such we need to ignore it.

While we are modifying these functions, fix and optimize the following;

* set_voltage_sel callback was using .reg instead of .vsel_reg - since
  they were set to the same value it actually didn't break anything but
  it would be semantically incorrect to use .reg in this case. We now use
  .vsel_reg and be consistent.
* vsel_shift is always 0 for every SWx regulator, and constantly shifting
  and masking off the bottom few bits is time consuming and makes the
  code very hard to read - optimize this out.
* get_voltage_sel uses the variable "val" and set_voltage_sel uses the
  variable "selector" (and reg_value). Introduce the variable "selector"
  to get_voltage_sel such that it makes more sense and allow some leaner
  code in light of the modifications in this patch. Add better exposure
  to the debug print so the register value AND the selector are printed as
  this will adequately show the HI bit in the register.
* correct a comment in probe which is doing a version check. Magic
  values are awful but for once instance, a comment does just as
  good a job as something symbolic.

Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Tested-by: Steev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-27 11:22:21 +08:00
Bill Pemberton
8dc995f56e regulator: remove use of __devexit
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-20 10:53:38 +09:00
Bill Pemberton
a5023574d1 regulator: remove use of __devinit
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-20 10:31:26 +09:00
Bill Pemberton
5eb9f2b963 regulator: remove use of __devexit_p
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-20 10:31:19 +09:00
Axel Lin
b571dc38d4 regulator: mc13xxx: Remove get_voltage implementation for single voltage regulators
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:27 -07:00
Axel Lin
f1dcf9e4ed regulator: mc13892: Convert mc13892_sw_regulator_ops to get_voltage_sel
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:24 -07:00
Axel Lin
8db98440fa regulator: mc13892: Simplify implementation of mc13892_sw_regulator_set_voltage_sel()
Use mc13xxx_reg_rmw rather than a mc13xxx_reg_read and a mc13xxx_reg_write calls.

This logic to set MC13892_SWITCHERS0_SWxHI bit is pretty simple:

if (volt > 1375000)
        set MC13892_SWITCHERS0_SWxHI bit
else if (volt < 1100000)
        clear MC13892_SWITCHERS0_SWxHI bit
else
        leave MC13892_SWITCHERS0_SWxHI bit untouched

We already know the selector, so we don't need to calculate the selector again.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:24 -07:00
Axel Lin
825d105910 regulator: mc13892: Make mc13892_powermisc_rmw() lock protected
Then we can remove lock/unlock around the caller.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:23 -07:00
Axel Lin
2c19ad43d1 regulator: mc13xxx: Remove mc13xxx_sw_regulator_is_enabled function
If .is_enabled callback is not implemented, regulator core assumes that the
regulator is always on. Thus we don't need mc13xxx_sw_regulator_is_enabled
function.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 12:06:25 +01:00
Axel Lin
34e74f39fa regulator: mc13xxx: Convert to regulator_list_voltage_table
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:01:21 +01:00
Mark Brown
b920eb41a8 Linux 3.4-rc2
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPgOpXAAoJEHm+PkMAQRiG8eUIAJ3Hjo0o5hqzxol8LWHDGF8s
 3h59qwRtts82u2psStZULPLbBzw6yjn8U5Mcrh7pffwCG2BzBL5rXcmXfvoPaET3
 TjylIj986Jv+jwZyuyZcLzYyoUtgjtq7hnt4tgVVEPlexYs7LxUl8vO8QjxT+bVO
 7eKgzLsXlBC9kw4P5M7kOBQ9NE5vmEcKf+fB3Hu3DqfVJtw9Lb7EeDQj/cbQsGqI
 vavSxe7lMTPsgMP2+hRz4txGTDJNRazkO2BdwfYrcNwTSa8tfBFlamww3y4+eJtq
 MFQfdNxQpumh2++T4IC2i/nLaawH7kWj2EdaRCRLMy9hVlb/v8/wcgd+1nfLkU8=
 =0on9
 -----END PGP SIGNATURE-----

Merge tag 'v3.4-rc2' into regulator-drivers

Linux 3.4-rc2 contains some fixes that further patches depend upon.
2012-04-10 09:52:59 +01:00
Axel Lin
a9d5801041 regulator: Fix build error for mc13783 and mc13892
Convert mc13783 and mc13892 to use a struct to pass in regulator runtime
configuration.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-10 09:52:53 +01:00
Axel Lin
939b62d897 regulator: Convert mc13xxx regulator drivers to set_voltage_sel
Convert mc13892_sw_regulator_ops and mc13xxx_regulator_ops to set_voltage_sel.
mc13xxx_get_best_voltage_index function is not used now, remove it.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-02 23:24:46 +01:00
Axel Lin
5777d9b34a regulator: Fix unbalanced lock/unlock in mc13892_regulator_probe error path
We do not hold a lock while registering regulator, thus should not call unlock
if regulator_register fails.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-03-26 18:32:11 +01:00
Fabio Estevam
4fef21eaac regulator: mc13892: Convert to devm_kzalloc()
Convert mc13892-regulator driver to use devm_kzalloc().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-30 02:06:29 +00:00
Shawn Guo
93bcb23b38 regulator: mc13892: add device tree probe support
It adds device tree probe support for mc13892-regulator driver.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-22 11:10:45 +00:00
Rajendra Nayak
2c043bcbf2 regulator: pass additional of_node to regulator_register()
With device tree support for regulators, its needed that the
regulator_dev->dev device has the right of_node attached.
To be able to do this add an additional parameter to the
regulator_register() api, wherein the dt-adapted driver can
then pass this additional info onto the regulator core.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 18:47:04 +00:00
Paul Gortmaker
65602c32ee regulator: Add module.h to drivers/regulator users as required
Another group of drivers that are taking advantage of the implicit
presence of module.h -- and will break when we pull the carpet out
from under them during a cleanup.  Fix 'em now.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:32:15 -04:00
Fabio Estevam
6dc4efc6d5 regulator: mc13892: Fix voltage unit in test case.
Voltage values should be expressed in microvolts, not in milivolts.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-05-27 10:49:10 +01:00
Axel Lin
327e15af15 Revert "regulator: Move VCOINCELL to be the last element of mc13892_regulators array"
I check this patch again and found this actually is not a bug
because MC13xxx_DEFINE explictly defines the order of each entry in the array.

Thus revert the patch.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-05-27 10:49:09 +01:00
Axel Lin
98ea5c218e regulator: Use mc13xxx_reg_write instead of mc13xxx_reg_rmw in mc13892_sw_regulator_set_voltage
Currently, we call mc13xxx_reg_read and mc13xxx_reg_rmw for the same register.
This can be converted to simply a mc13xxx_reg_read and a mc13xxx_reg_write,
thus save a redundant register read.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-05-27 10:34:37 +01:00
Axel Lin
ba413c5972 regulator: Move VCOINCELL to be the last element of mc13892_regulators array
In include/linux/mfd/mc13892.h, we define MC13892_VCOINCELL as 23.
Thus VCOINCELL should be defined as 23th element in mc13892_regulators array, not the first one.
This actually fixes an off-by-one bug while accessing mc13892_regulators array.

For example,
In mc13892_regulator_probe, we use MC13892_VCAM as array index of mc13892_regulators array.
        mc13892_regulators[MC13892_VCAM].desc.ops->set_mode
                = mc13892_vcam_set_mode;
Currently, it access mc13892_regulators[12] ,which is VAUDIO not VCAM.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-05-27 10:34:37 +01:00
Samuel Ortiz
c8a03c96b6 mfd: Use mfd cell platform_data for mc13xxx cells platform bits
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-05-26 19:45:07 +02:00
Andres Salomon
4ec1b54c4d mfd: mfd_cell is now implicitly available to mc13xxx drivers
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.

Note that mfd-core no longer makes a copy of platform_data, but the
mc13xxx-core driver creates the pdata structures on the stack.  In
order to get around that, the various ARM mach types that set the
pdata have been changed to hold the variable in static (global) memory.
Also note that __initdata references in aforementioned pdata structs
have been dropped.

Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-03-23 10:41:54 +01:00
Axel Lin
923430cfee regulator: Assign return value of mc13xxx_reg_rmw to ret
Otherwise, we will not return error if write to MC13892_SWITCHERS5 failed.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Mark Brown
27315cf61f regulator: Staticise non-exported functions in mc13892
No point exposing functions that aren't used elsewhere to the global
namespace and sparse warns about doing so.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Yong Shen
5e428d5cec regulator: support PMIC mc13892
add support for mc13892, tested on mx51 babbage board

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:03 +00:00