PTE/PDE doesn't support a single update (count = 1). We had
previously disabled it since it we were hitting that case which
let to hangs. The PTE/PDE packet is much more efficient for VM
updates where it can be used.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow userspace to query for the tile mode array so userspace can properly
compute surface pitch and alignment requirement depending on tiling.
v2: Make strict aliasing safer by casting to char when copying
v3: merge fix from Christian
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add new ioctl option and bumb minor version number.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the disabled rb mask register is not properly initialized
program a sane default based on the number of RBs for the
asic. This avoids a potential divide by 0 when calculating
the backend mask.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We use the DMA ring rather than the GFX ring for
bo moves. This code was never used and commented out.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: set UVD tiling config for rv730
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Just until we get proper DPM for that.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just everything needed to decode videos using UVD.
v6: just all the bugfixes and support for R7xx-SI merged in one patch
v7: UVD_CGC_GATE is a write only register, lockup detection fix
v8: split out VRAM fallback changes, remove support for RV770,
add support for HEMLOCK, add buffer sizes checks
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Let the CS module decide if we can fall back to VRAM or not.
v2: remove unintended change
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: update error message and comment
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch allows the CPU to map the stolen vram segment
directly rather than going through the PCI BAR. This
significantly improves performance for certain workloads with
a properly patched ddx.
Use radeon.fastfb=1 to enable it (disabled by default).
Currently only supported on RS690, but support for RS780/880
and newer APUs may be added eventually.
Signed-off-by: Samuel Li <samuel.li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a per-asic MC (memory controller) mask which holds the
mak address mask the asic is capable of. Use this when
calculating the vram and gtt locations rather using asic
specific functions or limiting everything to 32 bits.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Doesn't affect anything as the same address gets written
in both cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Daniel writes:
"Just three revert/disable by default patches, one of them cc: stable
(since the offending commit was cc: stable, too)."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
Revert "drm/i915: write backlight harder"
drm/i915: don't disable the power well yet
Revert "drm/i915: set TRANSCODER_EDP even earlier"
Inki writes:
Includes bug fixes and code cleanups.
And it considers some restrictions to G2D hardware.
With this, the malfunction and page fault issues to g2d driver
would be fixed.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Check g2d cmd list for g2d restrictions
drm/exynos: Add a new function to get gem buffer size
drm/exynos: Deal with g2d buffer info more efficiently
drm/exynos: Clean up some G2D codes for readability
drm/exynos: Fix G2D core malfunctioning issue
drm/exynos: clear node object type at gem unmap
drm/exynos: Fix error routine to getting dma addr.
drm/exynos: Replaced kzalloc & memcpy with kmemdup
drm/exynos: fimd: calculate the correct address offset
drm/exynos: Make mixer_check_timing static
drm/exynos: modify the compatible string for exynos fimd
This reverts commit cf0a6584aa.
Turns out that cargo-culting breaks systems. Note that we can't revert
further, since
commit 770c12312a
Author: Takashi Iwai <tiwai@suse.de>
Date: Sat Aug 11 08:56:42 2012 +0200
drm/i915: Fix blank panel at reopening lid
fixed a regression in 3.6-rc kernels for which we've never figured out
the exact root cause. But some further inspection of the backlight
code reveals that it's seriously lacking locking. And especially the
asle backlight update is know to get fired (through some smm magic)
when writing specific backlight control registers. So the possibility
of suffering from races is rather real.
Until those races are fixed I don't think it makes sense to try
further hacks. Which sucks a bit, but sometimes that's how it is :(
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org (the reverted commit was cc: stable, too)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're still not 100% ready to disable the power well, so don't disable
it for now. When we disable it we break the audio driver (because some
of the audio registers are on the power well) and machines with eDP on
port D (because it doesn't use TRANSCODER_EDP).
Also, instead of just reverting the code, add a Kernel option to let
us disable it if we want. This will allow us to keep developing and
testing the feature while it's not enabled.
This fixes problems caused by the following commit:
commit d6dd9eb1d9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jan 29 16:35:20 2013 -0200
drm/i915: dynamic Haswell display power well support
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit cc464b2a17.
The reason is that Takashi Iwai reported a regression bisected to this
commit:
http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
His machine has eDP on port D (usual desktop all-in-on setup), which
intel_dp.c identifies as an eDP panel, but the hsw ddi code
mishandles.
Closer inspection of the code reveals that haswell_crtc_mode_set also
checks intel_encoder_is_pch_edp when setting is_cpu_edp. On haswell
that doesn't make much sense (since there's no edp on the pch), but
what this function _really_ checks is whether that edp connector is on
port A or port D. It's just that on ilk-ivb port D was on the pch ...
So that explains why this seemingly innocent change killed eDP on port
D. Furthermore it looks like everything else accidentally works, since
we've never enabled eDP on port D support for hsw intentionally (e.g.
we still register the HDMI output for port D in that case).
But in retrospective I also don't like that this leaks highly platform
specific details into common code, and the reason is that the drm
vblank layer sucks. So instead I think we should:
- move the cpu_transcoder into the dynamic pipe_config tracking (once
that's merged).
- fix up the drm vblank layer to finally deal with kms crtc objects
instead of int pipes.
v2: Pimp commit message with the better diagnosis as discussed with
Paulo on irc.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes this time around. The iscsi-target CHAP
big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
stable.
Also, there is a persistent reservations regression that has recently
been reported for >= v3.8.x code, that is currently being tracked down
for v3.9."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/pscsi: Reject cross page boundary case in pscsi_map_sg
target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
tcm_vhost: Flush vhost_work in vhost_scsi_flush()
tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
target: fix possible memory leak in core_tpg_register()
target/iscsi: Fix mutual CHAP auth on big-endian arches
target_core_sbc: use noop for SYNCHRONIZE_CACHE
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Rycs
-----END PGP SIGNATURE-----
Merge tag 'md-3.9-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"A few bugfixes for md
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable"
* tag 'md-3.9-fixes' of git://neil.brown.name/md:
md: remove CONFIG_MULTICORE_RAID456 entirely
md/raid5: ensure sync and DISCARD don't happen at the same time.
MD: Prevent sysfs operations on uninitialized kobjects
MD RAID5: Avoid accessing gendisk or queue structs when not available
md/raid5: schedule_construction should abort if nothing to do.
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
Pull watchdog fixes from Wim Van Sebroeck:
"Fix a boot issues and correct the AcpiMmioSel bitmask in the
sp5100_tco watchdog device driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
watchdog: sp5100_tco: Remove code that may cause a boot failure
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull NVMe driver update from Matthew Wilcox:
"These patches have mostly been baking for a few months; sorry I didn't
get them in during the merge window. They're all bug fixes, except
for the addition of the SMART log and the addition to MAINTAINERS."
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Add namespaces with no LBA range feature
MAINTAINERS: Add entry for the NVMe driver
NVMe: Initialize iod nents to 0
NVMe: Define SMART log
NVMe: Add result to nvme_get_features
NVMe: Set result from user admin command
NVMe: End queued bio requests when freeing queue
NVMe: Free cmdid on nvme_submit_bio error
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
mm/hotplug: only free wait_table if it's allocated by vmalloc
dma-debug: update DMA debug API to better handle multiple mappings of a buffer
dma-debug: fix locking bug in check_unmap()
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
drivers/rtc/rtc-da9052.c: fix for rtc device registration
mm: zone_end_pfn is too small
poweroff: change orderly_poweroff() to use schedule_work()
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
printk: Provide a wake_up_klogd() off-case
irq_work.h: fix warning when CONFIG_IRQ_WORK=n
On some revisions of AT91 SoCs, the RTC IMR register is not working.
Instead of elaborating a workaround for that specific SoC or IP version,
we simply use a software variable to store the Interrupt Mask Register
and modify it for each enabling/disabling of an interrupt. The overhead
of this is negligible anyway.
The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5
sub-family of SoCs (good overview of the members here:
http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible
effect" is the RTC doesn't work.
That sub-family is less than two years old and only has devicetree (DT)
support and came online circa lk 3.7 . The dust is yet to settle on the
DT stuff at least for AT91 SoCs (translation: lots of stuff is still
broken, so much that it is hard to know where to start).
The fix in the patch is pretty simple: just shadow the silicon IMR
register with a variable in the driver. Some older SoCs (pre-DT) use the
the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should
not be impacted by the change. There shouldn't be a large volume of
interrupts associated with a RTC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit be86781497 ("drivers/video/ep93xx-fb.c: use devm_ functions")
introduced a build error:
drivers/video/ep93xx-fb.c: In function 'ep93xxfb_probe':
drivers/video/ep93xx-fb.c:532: error: implicit declaration of function 'devm_ioremap'
drivers/video/ep93xx-fb.c:533: warning: assignment makes pointer from integer without a cast
Include <linux/io.h> to pickup the declaration of 'devm_ioremap'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Cc: Damien Cassou <damien.cassou@lifl.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the virtual irq since now MFD only handles virtual irq
Without this patch rtc device will fail in registration.
(akpm: Ashish has a different version whcih will be needed for 3.8.x and
earlier kernels)
Signed-off-by: Ashish <ashish.jangam@kpitcummins.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AcpiMmioSel bit is bit 1 in the AcpiMmioEn register, but the current
sp5100_tco driver is using bit 2.
See 2.3.3 Power Management (PM) Registers page 150 of the
AMD SB800-Series Southbridges Register Reference Guide [1].
AcpiMmioEn - RW – 8/16/32 bits - [PM_Reg: 24h]
Field Name Bits Default Description
AcpiMMioDecodeEn 0 0b Set to 1 to enable AcpiMMio space.
AcpiMMIoSel 1 0b Set AcpiMMio registers to be memory-mapped or IO-mapped space.
0: Memory-mapped space
1: I/O-mapped space
The sp5100_tco driver expects zero as a value of AcpiMmioSel (bit 1).
Fortunately, no problems were caused by this typo, because the default
value of the undocumented misused bit 2 seems to be zero.
However, the sp5100_tco driver should use the correct bitmask value.
[1] http://support.amd.com/us/Embedded_TechDocs/45482.pdf
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
A problem was found on PC's with the SB700 chipset: The PC fails to
load BIOS after running the 3.8.x kernel until the power is completely
cut off. It occurs in all 3.8.x versions and the mainline version as of
2/4. The issue does not occur with the 3.7.x builds.
There are two methods for accessing the watchdog registers.
1. Re-programming a resource address obtained by allocate_resource()
to chipset.
2. Use the direct memory-mapped IO access.
The method 1 can be used by all the chipsets (SP5100, SB7x0, SB8x0 or
later). However, experience shows that only PC with the SB8x0 (or
later) chipsets can use the method 2.
This patch removes the method 1, because the critical problem was found.
That's why the watchdog timer was able to be used on SP5100 and SB7x0
chipsets until now.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1116835
Link: https://lkml.org/lkml/2013/2/14/271
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
Here are a number of USB fixes that resolve issues that have been reported
against 3.9-rc3.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlFMnR0ACgkQMUfUDdst+yliJwCeNOJ0bz7Crzs3NepnRWHaHJ0Z
OmQAnRvQMX1OpqDCsjnc7RW2gL/2TDNd
=05gg
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of USB fixes that resolve issues that have been
reported against 3.9-rc3."
* tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (37 commits)
USB: ti_usb_3410_5052: fix use-after-free in TIOCMIWAIT
USB: ssu100: fix use-after-free in TIOCMIWAIT
USB: spcp8x5: fix use-after-free in TIOCMIWAIT
USB: quatech2: fix use-after-free in TIOCMIWAIT
USB: pl2303: fix use-after-free in TIOCMIWAIT
USB: oti6858: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix broken TIOCMIWAIT
USB: mct_u232: fix use-after-free in TIOCMIWAIT
USB: io_ti: fix use-after-free in TIOCMIWAIT
USB: io_edgeport: fix use-after-free in TIOCMIWAIT
USB: ftdi_sio: fix use-after-free in TIOCMIWAIT
USB: f81232: fix use-after-free in TIOCMIWAIT
USB: cypress_m8: fix use-after-free in TIOCMIWAIT
USB: ch341: fix use-after-free in TIOCMIWAIT
USB: ark3116: fix use-after-free in TIOCMIWAIT
USB: serial: add modem-status-change wait queue
USB: serial: fix interface refcounting
USB: io_ti: fix get_icount for two port adapters
USB: garmin_gps: fix memory leak on disconnect
...
fix from Stephen Hemminger.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XVNg
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fixes from Borislav Petkov:
"A fix from Mauro to correct csrow size accounting in sysfs and a
sparse fix from Stephen Hemminger."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Merge mci.mem_is_per_rank with mci.csbased
amd64_edac: Correct DIMM sizes
EDAC: Make sysfs functions static
The LBA Range Type feature is optional in the NVMe specification,
so we should continue with adding namespaces for controllers that do
not implement this feature.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
