The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based addressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.
This code updates the of_serial driver to handle the reg-offset
and reg-shift properties to enable this core to be used.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The of_serial driver queries the current-speed property and attempts
to use it to register the custom_divisor property of the uart_port.
However, if current-speed is not set, then this code will dereference
a bad pointer. The fix is to only set custom_divisor when a
current-speed property appears in the device tree.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Fix the following section mismatches:
WARNING: drivers/built-in.o(.exit.text+0x5a): Section mismatch in reference from the function of_platform_serial_exit() to the variable .devinit.data:of_platform_serial_driver
The function __exit of_platform_serial_exit() references
a variable __devinitdata of_platform_serial_driver.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, of_serial driver supports only 8250 compatible ports, but
prepares that others can easily be added. Yet unregister routine
assumes port is 8250. This corrects unregister routine to check
port type.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current of_serial driver assumes unknown serial port to be 8250. But
this behavior may cause fatal problems when the serial port is not
8250. This corrects probe routine to ignore unknown serial port.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, the serial core always allows setserial in userspace to change the
port address, irq and base clock of any serial port. That makes sense for
legacy ISA ports, but not for (say) embedded ns16550 compatible serial ports
at peculiar addresses. In these cases, the kernel code configuring the ports
must know exactly where they are, and their clocking arrangements (which can
be unusual on embedded boards). It doesn't make sense for userspace to change
these settings.
Therefore, this patch defines a UPF_FIXED_PORT flag for the uart_port
structure. If this flag is set when the serial port is configured, any
attempts to alter the port's type, io address, irq or base clock with
setserial are ignored.
In addition this patch uses the new flag for on-chip serial ports probed in
arch/powerpc/kernel/legacy_serial.c, and for other hard-wired serial ports
probed by drivers/serial/of_serial.c.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This can be used for serial ports that are connected to an
OF platform bus but are not autodetected by the lecacy
serial support.
It will automatically take over devices that come from the
legacy serial detection, which usually is only one device.
In some cases, rtas may be set up to use the serial port
in the firmware, which allows easier debugging before probing
the serial ports. In this case, the "used-by-rtas" property
must be set by the firmware. This patch also adds code to the
legacy serial driver to check for this.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
