If hardware-driven P-state selection (HWP) is enabled, the
"performance" mode of intel_pstate should only allow the processor
to use the highest-performance P-state available. That is not
the case currently, so make it actually happen.
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The SCPI clk driver registers the virtual cpufreq device that kicks off
initialisation of the SCPI cpufreq driver. Also, clk_get() will fail for
the cpufreq driver if the SCPI clk driver is missing.
Fix this by making the SCPI cpufreq driver explicitly depend on the SCPI
clk driver.
Fixes: 8def31034d (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A rounding error was found in the calculation of limits->max_perf
in intel_pstate_set_policy(), which is used to calculate the max and min
pstate values in intel_pstate_get_min_max(). In that code,
limits->max_perf is truncated to 2 hex digits such that, for example,
0x169 was incorrectly calculated to 0x16 instead of 0x17. This resulted in
the pstate being set one level too low. This patch rounds the value of
limits->max_perf up instead of down so that the correct max pstate can
be reached.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I have a Intel (6,63) processor with a "marketing" frequency (from
/proc/cpuinfo) of 2100MHz, and a max turbo frequency of 2600MHz. I
can execute
cpupower frequency-set -g powersave --min 1200MHz --max 2100MHz
and the max_freq_pct is set to 80. When adding load to the system I noticed
that the cpu frequency only reached 2000MHZ and not 2100MHz as expected.
This is because limits->max_policy_pct is calculated as 2100 * 100 /2600 = 80.7
and is rounded down to 80 when it should be rounded up to 81. This patch
adds a DIV_ROUND_UP() which will return the correct value.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Subsys interface's ->remove_dev() is called when the cpufreq driver is
unregistering or the CPU is getting physically removed. We keep removing
the cpuX/cpufreq link for all CPUs except the last one, which is a
mistake as all CPUs contain a link now.
Because of this, one CPU from each policy will still contain a link (to
an already removed policyX directory), after the cpufreq driver is
unregistered.
Fix that by removing the link first and then only see if the policy is
required to be freed. That will make sure that no links are left out.
Fixes: 96bdda61f5 ("cpufreq: create cpu/cpufreq/policyX directories")
Reported-and-tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The CPU policy struct indicates the co-ordination type
for all CPUs of a common freq domain. Initialize it
correctly using the CPU specific data gathered from
CPPC ACPI lib via acpi_get_psd_map().
The PSD object is optional, so the cpu->shared_type
can also be 0. So instead of assuming any value other
than SW_ANY(0xFD) is unsupported, explictly check
if shared_type is SW_ALL and then bail.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq:
Revert "Documentation: kernel_parameters for Intel P state driver"
cpufreq: mediatek: fix build error
cpufreq: intel_pstate: Add separate support for Airmont cores
cpufreq: intel_pstate: Replace BYT with ATOM
Revert "cpufreq: intel_pstate: Use ACPI perf configuration"
Revert "cpufreq: intel_pstate: Avoid calculation for max/min"
* acpi-cppc:
ACPI / CPPC: Use h/w reduced version of the PCCT structure
The recently added mt8173 cpufreq driver relies on the cpu topology
that is always present on ARM64 but optional on ARM32:
drivers/cpufreq/mt8173-cpufreq.c: In function 'mtk_cpufreq_init':
drivers/cpufreq/mt8173-cpufreq.c:441:30: error: 'cpu_topology' undeclared (first use in this function)
cpumask_copy(policy->cpus, &cpu_topology[policy->cpu].core_sibling);
This refines the Kconfig dependencies so that we can still build on
ARM32, but only if COMPILE_TEST is selected and the CPU topology
code is present.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two flavors of Atom cores to be supported by intel_pstate,
Silvermont and Airmont, so make the driver distinguish between them by
adding separate frequency tables.
Separate the CPU defaults params for each of them and match the CPU IDs
against them as appropriate.
Signed-off-by: Philippe Longepe <philippe.longepe@linux.intel.com>
Signed-off-by: Stephane Gasparini <stephane.gasparini@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename symbol and function names starting with "BYT" or "byt" to
start with "ATOM" or "atom", respectively, so as to make it clear
that they may apply to Atom in general and not just to Baytrail
(the goal is to support several Atoms architectures eventually).
This should not lead to any functional changes.
Signed-off-by: Philippe Longepe <philippe.longepe@linux.intel.com>
Signed-off-by: Stephane Gasparini <stephane.gasparini@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 37afb00032 (cpufreq: intel_pstate: Use ACPI perf
configuration) that is reported to cause a regression to happen
on a system where invalid data are returned by the ACPI _PSS object.
Since that commit makes assumptions regarding the _PSS output
correctness that may turn out to be overly optimistic in general,
there is a concern that it may introduce regression on more
systems, so it's better to revert it now and we'll revisit the
underlying issue in the next cycle with a more robust solution.
Conflicts:
drivers/cpufreq/intel_pstate.c
Fixes: 37afb00032 (cpufreq: intel_pstate: Use ACPI perf configuration)
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 4ef4514870 (cpufreq: intel_pstate: Avoid calculation for
max/min) as it depends on commit 37afb00032 (cpufreq: intel_pstate: Use
ACPI perf configuration) that causes problems to happen and needs to be
reverted.
Conflicts:
drivers/cpufreq/intel_pstate.c
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Support for the ACPI _CCA configuration object intended to tell
the OS whether or not a bus master device supports hardware
managed cache coherency and a new set of functions to allow
drivers to check the cache coherency support for devices in a
platform firmware interface agnostic way (Suravee Suthikulpanit,
Jeremy Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan,
Thomas Renninger).
- turbostat tool updates (Len Brown).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=XZiP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"The only new feature in this batch is support for the ACPI _CCA device
configuration object, which it a pre-requisite for future ACPI PCI
support on ARM64, but should not affect the other architectures.
The rest is fixes and cleanups, mostly in cpufreq (including
intel_pstate), the Operating Performace Points (OPP) framework and
tools (cpupower and turbostat).
Specifics:
- Support for the ACPI _CCA configuration object intended to tell the
OS whether or not a bus master device supports hardware managed
cache coherency and a new set of functions to allow drivers to
check the cache coherency support for devices in a platform
firmware interface agnostic way (Suravee Suthikulpanit, Jeremy
Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan, Thomas
Renninger).
- turbostat tool updates (Len Brown)"
* tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
PCI: ACPI: Add support for PCI device DMA coherency
PCI: OF: Move of_pci_dma_configure() to pci_dma_configure()
of/pci: Fix pci_get_host_bridge_device leak
device property: ACPI: Remove unused DMA APIs
device property: ACPI: Make use of the new DMA Attribute APIs
device property: Adding DMA Attribute APIs for Generic Devices
ACPI: Adding DMA Attribute APIs for ACPI Device
device property: Introducing enum dev_dma_attr
ACPI: Honor ACPI _CCA attribute setting
cpufreq: CPPC: Delete an unnecessary check before the function call kfree()
PM / OPP: Add opp_rcu_lockdep_assert() to _find_device_opp()
PM / OPP: Hold dev_opp_list_lock for writers
PM / OPP: Protect updates to list_dev with mutex
PM / OPP: Propagate error properly from dev_pm_opp_set_sharing_cpus()
cpufreq: s5pv210-cpufreq: fix wrong do_div() usage
MAINTAINERS: update for intel P-state driver
Creating a common structure initialization pattern for struct option
cpupower: Enable disabled Cstates if they are below max latency
cpupower: Remove debug message when using cpupower idle-set -D switch
cpupower: cpupower monitor reports uninitialized values for offline cpus
...
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
* pm-cpufreq:
cpufreq: s5pv210-cpufreq: fix wrong do_div() usage
MAINTAINERS: update for intel P-state driver
cpufreq: governor: Quit work-handlers early if governor is stopped
intel_pstate: decrease number of "HWP enabled" messages
cpufreq: arm_big_little: fix frequency check when bL switcher is active
* acpi-video:
ACPI / video: only register backlight for LCD device
ACPI / video: Add a quirk to force acpi-video backlight on Dell XPS L421X
* acpi-cppc:
cpufreq: CPPC: Delete an unnecessary check before the function call kfree()
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is wrong to use do_div() with 32-bit dividends (unsigned long is
32 bits on 32-bit architectures).
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
gov_queue_work() acquires cpufreq_governor_lock to allow
cpufreq_governor_stop() to drain delayed work items possibly scheduled
on CPUs that share the policy with a CPU being taken offline.
However, the same goal may be achieved in a more straightforward way if
the policy pointer in the struct cpu_dbs_info matching the policy CPU is
reset upfront by cpufreq_governor_stop() under the timer_mutex belonging
to it and checked against NULL, under the same lock, at the beginning of
dbs_timer().
In that case every instance of dbs_timer() run for a struct cpu_dbs_info
sharing the policy pointer in question after cpufreq_governor_stop() has
started will notice that that pointer is NULL and bail out immediately
without queuing up any new work items. In turn, gov_cancel_work()
called by cpufreq_governor_stop() before destroying timer_mutex will
wait for all of the delayed work items currently running on the CPUs
sharing the policy to drop the mutex, so it may be destroyed safely.
Make cpufreq_governor_stop() and dbs_timer() work as described and
modify gov_queue_work() so it does not acquire cpufreq_governor_lock any
more.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When booting an HWP enabled system the kernel displays one "HWP enabled"
message for each cpu. The messages are superfluous since HWP is globally
enabled across all CPUs. This patch also adds an informational message
when HWP is disabled via intel_pstate=no_hwp.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The check for correct frequency being set in bL_cpufreq_set_rate is
broken when the big.LITTLE switcher is active, for two reasons.
1. The 'new_rate' variable gets overwritten before the test by the
code calculating the frequency of the old cluster.
2. The frequency returned by bL_cpufreq_get_rate will be the virtual
frequency, not the actual one the intended version of new_rate contains.
This means the function always returns an error causing an endless
stream of: "cpufreq: __target_index: Failed to change cpu frequency: -5"
As the intent is to check for errors that clk_set_rate doesn't report
lets move the check to immediately after that and directly use
clk_get_rate, rather than the arm_big_little helpers which only confuse
matters. Also, update the comment to be hopefully clearer about the
purpose of the code.
Fixes: 0a95e630b4 (cpufreq: arm_big_little: check if the frequency is set correctly)
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-opp:
PM / OPP: passing NULL to PTR_ERR()
PM / OPP: Move cpu specific code to opp/cpu.c
PM / OPP: Move opp core to its own directory
PM / OPP: Prefix exported opp routines with dev_pm_opp_
PM / OPP: Rename opp init/free table routines
PM / OPP: reuse of_parse_phandle()
* pm-cpufreq:
cpufreq: postfix policy directory with the first CPU in related_cpus
cpufreq: create cpu/cpufreq/policyX directories
cpufreq: remove cpufreq_sysfs_{create|remove}_file()
cpufreq: create cpu/cpufreq at boot time
cpufreq: Use cpumask_copy instead of cpumask_or to copy a mask
cpufreq: ondemand: Drop unnecessary locks from update_sampling_rate()
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value
cpufreq: intel_pstate: Avoid calculation for max/min
Documentation: kernel_parameters for Intel P state driver
cpufreq: intel_pstate: Use ACPI perf configuration
cpufreq: intel-pstate: Use separate max pstate for scaling
cpufreq: intel_pstate: get P1 from TAR when available
cpufreq: Drop redundant check for inactive policies
cpufreq : powernv: Report Pmax throttling if capped below nominal frequency
cpufreq: imx: update the clock switch flow to support imx6ul
cpufreq: tegra20: remove superfluous CONFIG_PM ifdefs
cpufreq: conservative: remove 'enable' field
cpufreq: integrator: Fix module autoload for OF platform driver
* pm-cpuidle:
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
* acpi-processor:
ACPI / CPPC: Fix potential memory leak
ACPI / CPPC: signedness bug in register_pcc_channel()
ACPI: Allow selection of the ACPI processor driver for ARM64
CPPC: Probe for CPPC tables for each ACPI Processor object
ACPI: Add weak routines for ACPI CPU Hotplug
ACPI / CPPC: Add a CPUFreq driver for use with CPPC
ACPI: Introduce CPU performance controls using CPPC
The sysfs policy directory is postfixed currently with the CPU number
for which the policy was created, which isn't necessarily the first CPU
in related_cpus mask.
To make it more consistent and predictable, lets postfix the policy with
the first cpu in related-cpus mask.
Suggested-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq sysfs interface had been a bit inconsistent as one of the
CPUs for a policy had a real directory within its sysfs 'cpuX' directory
and all other CPUs had links to it. That also made the code a bit
complex as we need to take care of moving the sysfs directory if the CPU
containing the real directory is getting physically hot-unplugged.
Solve this by creating 'policyX' directories (per-policy) in
/sys/devices/system/cpu/cpufreq/ directory, where X is the CPU for which
the policy was first created.
This also removes the need of keeping kobj_cpu and we can remove it now.
Suggested-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Acked-by: is more of a general agreement from the person that he is
Reviewed-by: is a more strict tag and implies that the reviewer has
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
They don't do anything special now, remove the unnecessary wrapper.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later patches will need to create policy specific directories in
/sys/devices/system/cpu/cpufreq/ directory and so the cpufreq directory
wouldn't be ever empty.
And so no fun creating/destroying it on need basis anymore. Create it
once on system boot.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
->related_cpus is empty at this point of time and copying ->cpus to it
or orring ->related_cpus with ->cpus would result in the same value. But
cpumask_copy makes it rather clear.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'timer_mutex' is required to sync work-handlers of policy->cpus.
update_sampling_rate() is just canceling the works and queuing them
again. This isn't protecting anything at all in update_sampling_rate()
and is not gonna be of any use.
Even if a work-handler is already running for a CPU,
cancel_delayed_work_sync() will wait for it to finish.
Drop these unnecessary locks.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On systems that initialize the intel_pstate driver with the performance
governor, and then switch to the powersave governor will not transition to
lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct
is set to a low value.
The behavior of governor switching changed after commit a04759924e
("[cpufreq] intel_pstate: honor user space min_perf_pct override on
resume"). The commit introduced tracking of performance percentage
changes via sysfs in order to restore userspace changes during
suspend/resume. The problem occurs because the global values of the newly
introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor
change and this causes the powersave governor to inherit the performance
governor's settings.
A simple change would have been to reset max_sysfs_pct to 100 and
min_sysfs_pct to 0 on a governor change, which fixes the problem with
governor switching. However, since we cannot break userspace[1] the fix
is now to give each governor its own limits storage area so that governor
specific changes are tracked.
I successfully tested this by booting with both the performance governor
and the powersave governor by default, and switching between the two
governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values,
and looking at the output of cpupower frequency-info). Suspend/Resume
testing was performed by Doug Smythies.
[1] Systems which suspend/resume using the unmaintained pm-utils package
will always transition to the performance governor before the suspend and
after the resume. This means a system using the powersave governor will
go from powersave to performance, then suspend/resume, performance to
powersave. The simple change during governor changes would have been
overwritten when the governor changed before and after the suspend/resume.
I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225
against Fedora to remove the 94cpufreq file that causes the problem. It
should be noted that pm-utils is obsoleted with newer versions of systemd.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a workaround for KNL platform, where in some cases MPERF counter
will not have updated value before next read of MSR_IA32_MPERF. In this
case divide by zero will occur. This change ignores current sample for
busy calculation in this case.
Fixes: b34ef932d7 (intel_pstate: Knights Landing support)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When requested from cpufreq to set policy, look into _pss and get
control values, instead of using max/min perf calculations. These
calculation misses next control state in boundary conditions.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use ACPI _PSS to limit the Intel P State turbo, max and min ratios.
This driver uses acpi processor perf lib calls to register performance.
The following logic is used to adjust Intel P state driver limits:
- If there is no turbo entry in _PSS, then disable Intel P state turbo
and limit to non turbo max
- If the non turbo max ratio is more than _PSS max non turbo value, then
set the max non turbo ratio to _PSS non turbo max
- If the min ratio is less than _PSS min then change the min ratio
matching _PSS min
- Scale the _PSS turbo frequency to max turbo frequency based on control
value.
This feature can be disabled by using kernel parameters:
intel_pstate=no_acpi
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Systems with configurable TDP have multiple max non turbo p state. Intel
P state uses max non turbo P state for scaling. But using the real max
non turbo p state causes underestimation of next P state. So using
the physical max non turbo P state as before for scaling.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After Ivybridge, the max non turbo ratio obtained from platform info msr
is not always guaranteed P1 on client platforms. The max non turbo
activation ratio (TAR), determines the max for the current level of TDP.
The ratio in platform info is physical max. The TAR MSR can be locked,
so updating this value is not possible on all platforms.
This change gets this ratio from MSR TURBO_ACTIVATION_RATIO if
available,
but also do some sanity checking to make sure that this value is
correct.
The sanity check involves reading the TDP ratio for the current tdp
control value when platform has configurable TDP present and matching
TAC
with this.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9u+p
-----END PGP SIGNATURE-----
Merge tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
* tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: Support thermal zones registration for SCP temperature sensors
hwmon: Support sensors exported via ARM SCP interface
firmware: arm_scpi: Extend to support sensors
Documentation: add DT bindings for ARM SCPI sensors
cpufreq: arm_big_little: add SCPI interface driver
clk: scpi: add support for cpufreq virtual device
clk: add support for clocks provided by SCP(System Control Processor)
firmware: add support for ARM System Control and Power Interface(SCPI) protocol
Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
We just made sure policy->cpu is online and this check will always fail
as the policy is active. Drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver utilizes the methods introduced in a previous
patch titled - "ACPI: Introduce CPU performance controls using CPPC"
and enables usage with existing CPUFreq governors.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When scaling_available_frequencies is read on an offlined cpu, then
either lockup or junk values are displayed. This is caused by
freed freq_table, which policy is using.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control including CPU DVFS. SCPI Message Protocol is used to
communicate with the SCPI.
This patch adds a interface driver for adding OPPs and registering
the arm_big_little cpufreq driver for such systems.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Log a 'critical' message if the max frequency is reduced below nominal
frequency. We already log 'info' message if the max frequency is
capped below turbo frequency. CPU should guarantee atleast nominal
frequency, but not turbo frequency in all system configurations and
environments. So report the pmax throttling with severity when Pmax is
dipped below nominal frequency.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For i.MX6UL, the clock switch flow is slightly different from
other i.MX6 SOCs. It has a 'secondary_sel' clk that will be used
when the CPU freq is higher than 396MHz. So the clock switch flow in
'set_target' callback need to update to support i.MX6UL in the common
i.MX6 SOC cpufreq driver.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CONFIG_PM ifdefs are superfluous and can be removed.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Conservative governor has its own 'enable' field to check if
conservative governor is used for a CPU or not
This can be checked by policy->governor with 'cpufreq_gov_conservative'
and so this field can be dropped.
Because its not guaranteed that dbs_info->cdbs.shared will a valid
pointer for all CPUs (will be NULL for CPUs that don't use
ondemand/conservative governors), we can't use it anymore. Lets get
policy with cpufreq_cpu_get_raw() instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
