The extended century readout does not solve the year 2038 problem on
32bit!
v2: Fix compilation on !ACPI, pointed out by tglx
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We assume that the RTC clock is BCD, so print a warning if it claims
to be binary.
[ tglx@linutronix.de: changed to WARN_ON - we want to know that!
If no one reports it we can remove the complete if (RTC_ALWAYS_BCD)
magic, which has RTC_ALWAYS_BCD defined to 1 since Linux 1.0 ... ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We know it is already after 2000. Use the year 2000 offset for both 32
and 64 bit, which removes ifdefs and the 1970 magic.
[ tglx@linutronix.de: remove 1970 magic, replace bogus commit message ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change size to unsigned long, becase caller and user all used unsigned long.
Also make bad_addr take an alignment parameter.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The AMD Fam10h CPUs support new Gigabyte page table entry for
mapping 1GB at a time. Use this for the kernel direct mapping.
Only done for 64bit because i386 does not support GB page tables.
This only applies to the data portion of the direct mapping; the
kernel text mapping stays with 2MB pages because the AMD Fam10h
microarchitecture does not support GB ITLBs and AMD recommends
against using GB mappings for code.
Can be disabled with disable_gbpages on the kernel command line
[ tglx@linutronix.de: simplify enable code ]
[ Yinghai Lu <yinghai.lu@sun.com>: boot fix on 256 GB RAM ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These new controls toggle experimental support for a new CPU feature,
the straightforward extension of largepages from the pmd level to the
pud level, which allows 1GB (kernel) TLBs instead of 2MB TLBs.
Turn it off by default, as this code has not been tested well enough yet.
Use the CONFIG_DIRECT_GBPAGES=y .config option or gbpages on the
boot line can be used to enable it. If enabled in the .config then
nogbpages boot option disables it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Clean up the page table dumper (fix boundary conditions, table driven
address ranges, some formatting changes since it is no longer using
the kernel log but a separate virtual file), and generalize to 32
bits.
[ mingo@elte.hu: x86: fix the pagetable dumper ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds code to the kernel to have an (optional)
/proc/kernel_page_tables debug file that basically dumps the kernel
pagetables; this allows us kernel developers to verify that nothing fishy is
going on and that the various mappings are set up correctly. This was quite
useful in finding various change_page_attr() bugs, and is very likely to be
useful in the future as well.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: mingo@elte.hu
Cc: tglx@tglx.de
Cc: hpa@zytor.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unify arch/x86/mm/Makefile between 32 and 64 bits.
All configuration variables that are protected by Kconfig constraints
have been put in the common part of the Makefile; however, the NUMA
files are totally different between 32 and 64 bits and are handled via
an ifdef.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add debug information for DEBUG_PAGEALLOC to get some statistics about
the pool usage and split status.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We map a VMA for the 32-bit vDSO even when it's disabled, which is stupid.
For the 32-bit kernel it's the vdso_enabled boot parameter/sysctl
and for the 64-bit kernel it's the vdso32 boot parameter/syscall32 sysctl.
When it's disabled, we don't pass AT_SYSINFO_EHDR so processes don't use
the vDSO for anything, but we still map it. For the non-compat vDSO,
this means we're always putting an extra VMA somewhere, maybe lousing
up the control of the address space the user was hoping for.
Honor the setting by doing nothing in arch_setup_additional_pages.
[ also see: "x86 vDSO: don't use disabled vDSO for signal trampoline" ]
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the vDSO was not mapped, don't use it as the "restorer" for a signal
handler. Whether we have a pointer in mm->context.vdso depends on what
happened at exec time, so we shouldn't check any global flags now.
Background:
Currently, every 32-bit exec gets the vDSO mapped even if it's disabled
(the process just doesn't get told about it). Because it's in fact
always there, the bug that this patch fixes cannot happen now. With
the second patch, it won't be mapped at all when it's disabled, which is
one of the things that people might really want when they disable it (so
nothing they didn't ask for goes into their address space).
The 32-bit signal handler setup when SA_RESTORER is not used refers to
current->mm->context.vdso without regard to whether the vDSO has been
disabled when the process was exec'd. This patch fixes this not to use
it when it's null, which becomes possible after the second patch. (This
never happens in normal use, because glibc's sigaction call uses
SA_RESTORER unless glibc detected the vDSO.)
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
people sometimes do crazy stuff like building really large static
arrays into their kernels or building allyesconfig kernels. Give
more space to the kernel and push modules up a bit: kernel has
512 MB and modules have 1.5 GB.
Should be enough for a few years ;-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The header files for the Pb1200/DBAu1200 boards have wrong definition for the
IDE interface's decoded range length -- it should be 512 bytes according to
what the IDE driver does. In addition, the IDE platform device claims 1 byte
too many for its memory resource -- fix the platform code and the IDE driver
in accordance.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There's a libata based PATA driver for avr32, but no support for
drivers/ide/ on avr32.
This patch fixes the following compile error:
<-- snip -->
...
CC [M] drivers/ide/ide-cd.o
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/ide-cd.c:37:
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/ide.h:209:21: error: asm/ide.h: No such file or directory
make[3]: *** [drivers/ide/ide-cd.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
http://bugzilla.kernel.org/show_bug.cgi?id=10124
this change:
commit 08f1c192c3
Author: Muli Ben-Yehuda <muli@il.ibm.com>
Date: Sun Jul 22 00:23:39 2007 +0300
x86-64: introduce struct pci_sysdata to facilitate sharing of ->sysdata
This patch introduces struct pci_sysdata to x86 and x86-64, and
converts the existing two users (NUMA, Calgary) to use it.
This lays the groundwork for having other users of sysdata, such as
the PCI domains work.
The Calgary bits are tested, the NUMA bits just look ok.
replaces pcibios_scan_root by pci_scan_bus_parented...
but in pcibios_scan_root we have a check about scanned busses.
Cc: <yakui.zhao@intel.com>
Cc: Stian Jordet <stian@jordet.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Yinghai Lu" <yhlu.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The signal trampolines were accidently flushing the kernel I$ instead of
the users. Fix that up, and also add a missing user D$ flush while
we're at it.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/sh/kernel/traps_32.c: In function `do_reserved_inst':
arch/sh/kernel/traps_32.c:667: error: implicit declaration of function `do_fpu_inst'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
commit 54a0151041 broke zImage build on sh arch:
LD vmlinux
SYSMAP System.map
SYSMAP .tmp_System.map
AS arch/sh/boot/compressed/head_32.o
In file included from /k/arch/sh/boot/compressed/head_32.S:11:
/k/include/linux/linkage.h:34: error: syntax error in macro parameter list
Fix it for both sh and sh64.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes some compile errors due to missing save_fpu()
prototypes on sh64 caused by
commit 9bbafce2ee
(sh: Fix occasional FPU register corruption under preempt).
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Correctly determine the address of an illegal instruction. The EPCR0 register
holds this value (masked by EPCR0_PC) if the validity bit is set (masked by
EPCR0_V). So the test as to whether the contents of the register are usable
should be involve checking the _V bit, not the _PC bits.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The prevent_tail_call() macro works around the problem of the compiler
clobbering argument words on the stack, which for asmlinkage functions
is the caller's (user's) struct pt_regs. The tail/sibling-call
optimization is not the only way that the compiler can decide to use
stack argument words as scratch space, which we have to prevent.
Other optimizations can do it too.
Until we have new compiler support to make "asmlinkage" binding on the
compiler's own use of the stack argument frame, we have work around all
the manifestations of this issue that crop up.
More cases seem to be prevented by also keeping the incoming argument
variables live at the end of the function. This makes their original
stack slots attractive places to leave those variables, so the compiler
tends not clobber them for something else. It's still no guarantee, but
it handles some observed cases that prevent_tail_call() did not.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch also resolves hangs on boot:
http://lkml.org/lkml/2008/2/23/263http://bugzilla.kernel.org/show_bug.cgi?id=10093
The bug was causing once-in-few-reboots 10-15 sec wait during boot on
certain laptops.
Earlier commit 40d6a14662 added
smp_call_function in cpu_idle_wait() to kick cpus that are in tickless
idle. Looking at cpu_idle_wait code at that time, code seemed to be
over-engineered for a case which is rarely used (while changing idle
handler).
Below is a simplified version of cpu_idle_wait, which just makes a dummy
smp_call_function to all cpus, to make them come out of old idle handler
and start using the new idle handler. It eliminates code in the idle
loop to handle cpu_idle_wait.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make NOMMU-mode work with base addresses other than 0xC0000000 by:
(1) Giving the code that sets up the protection registers the right address
in __sdram_base. Rather than being hard coded to 0xC0000000, the value
of __page_offset is obtained from the linker script.
(2) Eliminate the check in __switch_to() that verifies the current thread
info is in the 0xCxxxxxxx region.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use traps 120-126 to emulate atomic cmpxchg32, xchg32, and XOR-, OR-, AND-, SUB-
and ADD-to-memory operations for userspace.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) ptrace should pass 'current' to task_user_regset_view()
2) When fetching general registers using a 64-bit view, and
the target is 32-bit, we have to convert.
3) Skip the whole register window get/set code block if
the user isn't asking to access anything in there.
Otherwise we have problems if the user doesn't have
an address space setup. Fetching ptrace register is
still valid at such a time, and ptrace does not try
to access the register window area of the regset.
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc expects all toplevel assembly to return to the original section type.
The code in alteranative.c does not do this. This caused some strange bugs
in sched-devel where code would end up in the .rodata section and when
the kernel sets the NX bit on all .rodata, the kernel would crash when
executing this code.
This patch adds a .previous marker to return the code back to the
original section.
Credit goes to Andrew Pinski for telling me it wasn't a gcc bug but a
bug in the toplevel asm code in the kernel. ;-)
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
flush_cache_vmap / flush_cache_vunmap were calling flush_cache_all which -
having been deprecated - turned into a nop ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In time_cpufreq_notifier() the cpu id to act upon is held in freq->cpu. Use it
instead of smp_processor_id() in the call to set_cyc2ns_scale().
This makes the preempt_*able() unnecessary and lets set_cyc2ns_scale() update
the intended cpu's cyc2ns.
Related mail/thread: http://lkml.org/lkml/2007/12/7/130
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
revert:
| commit 47001d6033
| Author: Thomas Gleixner <tglx@linutronix.de>
| Date: Tue Apr 1 19:45:18 2008 +0200
|
| x86: tsc prevent time going backwards
it has been identified to cause suspend regression - and the
commit fixes a longstanding bug that existed before 2.6.25 was
opened - so it can wait some more until the effects are better
understood.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix user accesses in regset code.
[SPARC64]: Fix FPU saving in 64-bit signal handling.
We handle a broken tsc these days, so no need to panic. We clear the
TSC bit when tsc_init decides it's unreliable (eg. under lguest w/ bad
host TSC), leading to bogus panic.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building UP kernel with KGDB enabled produces the following errors and warning
(fatal due to -Werror in arch/mips/kernel/Makefile):
In file included from arch/mips/kernel/gdb-stub.c:142:
include/asm/smp.h:25:1: "raw_smp_processor_id" redefined
In file included from include/linux/sched.h:69,
from arch/mips/kernel/gdb-stub.c:126:
include/linux/smp.h:88:1: this is the location of the previous definition
In file included from arch/mips/kernel/gdb-stub.c:142:
include/asm/smp.h:62: error: redefinition of 'smp_send_reschedule'
include/linux/smp.h:102: error: previous definition of 'smp_send_reschedule' was here
include/asm/smp.h: In function `smp_send_reschedule':
include/asm/smp.h:65: error: dereferencing pointer to incomplete type
arch/mips/kernel/gdb-stub.c: At top level:
arch/mips/kernel/gdb-stub.c:660: warning: 'kgdb_wait' defined but not used
Fix the errors by not directly including <asm/smp.h> (which is already included
by <linux/smp.h>) and the warning by enclosing kgdb_wait() in #ifdef CONFIG_SMP.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Long overdue update of the m68k defconfigs
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default defconfig should be one from arch/m68k/configs/
arch/m68k/defconfig was not exactly identical to amiga_defconfig but
also considering how long they have been without any update that doesn't
seem to have been on purpose.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commits:
commit 37a47db8d7
Author: Balaji Rao <balajirrao@gmail.com>
Date: Wed Jan 30 13:30:03 2008 +0100
x86: assign IRQs to HPET timers, fix
and
commit e3f37a54f6
Author: Balaji Rao <balajirrao@gmail.com>
Date: Wed Jan 30 13:30:03 2008 +0100
x86: assign IRQs to HPET timers
have been identified to cause a regression on some platforms due to
the assignement of legacy IRQs which makes the legacy devices
connected to those IRQs disfunctional.
Revert them.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=10382
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We already catch most of the TSC problems by sanity checks, but there
is a subtle bug which has been in the code for ever. This can cause
time jumps in the range of hours.
This was reported in:
http://lkml.org/lkml/2007/8/23/96
and
http://lkml.org/lkml/2008/3/31/23
I was able to reproduce the problem with a gettimeofday loop test on a
dual core and a quad core machine which both have sychronized
TSCs. The TSCs seems not to be perfectly in sync though, but the
kernel is not able to detect the slight delta in the sync check. Still
there exists an extremly small window where this delta can be observed
with a real big time jump. So far I was only able to reproduce this
with the vsyscall gettimeofday implementation, but in theory this
might be observable with the syscall based version as well.
CPU 0 updates the clock source variables under xtime/vyscall lock and
CPU1, where the TSC is slighty behind CPU0, is reading the time right
after the seqlock was unlocked.
The clocksource reference data was updated with the TSC from CPU0 and
the value which is read from TSC on CPU1 is less than the reference
data. This results in a huge delta value due to the unsigned
subtraction of the TSC value and the reference value. This algorithm
can not be changed due to the support of wrapping clock sources like
pm timer.
The huge delta is converted to nanoseconds and added to xtime, which
is then observable by the caller. The next gettimeofday call on CPU1
will show the correct time again as now the TSC has advanced above the
reference value.
To prevent this TSC specific wreckage we need to compare the TSC value
against the reference value and return the latter when it is larger
than the actual TSC value.
I pondered to mark the TSC unstable when the readout is smaller than
the reference value, but this would render an otherwise good and fast
clocksource unusable without a real good reason.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix obsolete printks in aperture-64. We used not to handle missing
agpgart, but we handle it okay now.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
right now if there's no CPU support for nmi_watchdog=2 we'll just
refuse it silently.
print a useful warning.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
implement nmi_watchdog=2 on this class of CPUs:
cpu family : 15
model : 6
model name : Intel(R) Pentium(R) D CPU 3.00GHz
the watchdog's ->setup() method is safe anyway, so if the CPU
cannot support it we'll bail out safely.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This avoids using wrmsr on MSR_IA32_DEBUGCTLMSR when it's not needed.
No wrmsr ever needs to be done if noone has ever used block stepping.
Without this change, using ptrace on 2.6.25 on an x86 KVM guest
will tickle KVM's missing support for the MSR and crash the guest
kernel. Though host KVM is the buggy one, this makes for a regression
in the guest behavior from 2.6.24->2.6.25 that we can easily avoid.
I also corrected some bad whitespace.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix MPC5200 (not B!) device tree so FEC ethernet works
[POWERPC] mpc5200: Amalgamated DTS fixes and updates
[POWERPC] Fix rtas_flash procfs interface
[POWERPC] Fix deadlock with mmu_hash_lock in hash_page_sync
[POWERPC] Fix iSeries hard irq enabling regression
[POWERPC] Fix CPM2 SCC1 clock initialization.
[POWERPC] Fix defconfigs so we dont set both GENRTC and RTCLIB
[POWERPC] fsldma: Use compatiable binding as spec
[POWERPC] sata_fsl: reduce compatibility to fsl,pq-sata
[POWERPC] 83xx: enable usb in 837x rdb and 83xx defconfigs
[POWERPC] 83xx: Fix wrong USB phy type in mpc837xrdb dts
The calculation of the FPU reg save area pointer
was wrong.
Based upon an OOPS report from Tom Callaway.
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets the FEC ethernet driver working again on the lite5200
platform.
The FEC driver is also compatible with the MPC5200, not only with the
MPC5200B, so this adds a suitable entry to the driver's match list.
Furthermore this adds the settings for the PHY in the dts file for the
Lite5200. Note, that this is not exactly the same as in the
Lite5200B, because the PHY is located at f0003000:01 for the 5200, and
at :00 for the 5200B. This was tested on a Lite5200 and a Lite5200B,
both booted a kernel via tftp and mounted the root via nfs
successfully.
Signed-off-by: René Bürgel <r.buergel@unicontrol.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Handling of the proc_dir_entry->count was changed in 2.6.24-rc5.
After this change, the default value for pde->count is 1 and not 0 as
before. Therefore, if we want to check whether our procfs file is
already opened (already in use), we have to check if pde->count is
greater than 2 rather than 1.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
hash_page_sync() takes and releases the low level mmu hash
lock in order to sync with other processors disposing of page
tables. Because that lock can be needed to service hash misses
triggered by interrupt handlers, taking it must be done with
interrupts off. However, hash_page_sync() appears to be called
with interrupts enabled, thus causing occasional deadlocks.
We fix it by making sure hash_page_sync() masks interrupts while
holding the lock.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A subtle bug sneaked into iSeries recently. On this platform, we must
not normally clear MSR:EE (the hardware external interrupt enable)
except for short periods of time. Taking an interrupt while
soft-disabled doesn't cause us to clear it for example.
The iSeries kernel expects to mostly run with MSR:EE enabled at all
times except in a few exception entry/exit code paths. Thus
local_irq_enable() doesn't check if it needs to hard-enable as it
expects this to be unnecessary on iSeries.
However, hard_irq_disable() _does_ cause MSR:EE to be cleared,
including on iSeries. A call to it was recently added to the
context switch code, thus causing interrupts to become disabled
for a long periods of time, causing the iSeries watchdog to kick
in under some circumstances and other nasty things.
This patch fixes it by making local_irq_enable() properly re-enable
MSR:EE on iSeries. It basically removes a return statement here
to make iSeries use the same code path as everybody else. That does
mean that we might occasionally get spurious decrementer interrupts
but I don't think that matters.
Another option would have been to make hard_irq_disable() a nop
on iSeries but I didn't like it much, in case we have good reasons
to hard-disable.
Part of the patch is fixes to make sure the hard_enabled PACA field
is properly set on iSeries as it used not to be before, since it
was mostly unused.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A missing break statement in a switch caused cpm2_clk_setup() to initialize
SCC2 instead of SCC1.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the problem that makedumpfile sometimes fails on x86_64 machine.
This patch adds the symbol "phys_base" to a vmcoreinfo data. The
vmcoreinfo data has the minimum debugging information only for dump
filtering. makedumpfile (dump filtering command) gets it to distinguish
unnecessary pages, and makedumpfile creates a small dumpfile.
On x86_64 kernel which compiled with CONFIG_PHYSICAL_START=0x0 and
CONFIG_RELOCATABLE=y, makedumpfile fails like the following:
# makedumpfile -d31 /proc/vmcore dumpfile
The kernel version is not supported.
The created dumpfile may be incomplete.
_exclude_free_page: Can't get next online node.
makedumpfile Failed.
#
The cause is the lack of the symbol "phys_base" in a vmcoreinfo data.
If the symbol "phys_base" does not exist, makedumpfile considers an
x86_64 kernel as non relocatable. As the result, makedumpfile
misunderstands the physical address where the kernel is loaded, and it
cannot translate a kernel virtual address to physical address correctly.
To fix this problem, this patch adds the symbol "phys_base" to a
vmcoreinfo data.
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <stable@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make dma_alloc_coherent respect gfp flags (__GFP_COMP is one that
matters).
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Tested-by: Michael Cree <mcree@orcon.net.nz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/ralf/upstream-linus:
[MIPS] XSS1500: Fix compilation
[MIPS] Bigsur: make defconfig more useful.
[MIPS] Alchemy: work around clock misdetection on early Au1000
[MIPS] Add missing 4KEC TLB refill handler
[MIPS] BCM1480: Fix PCI/HT IO access
[MIPS] Fix the installation condition of MIPS clocksource
[MIPS] Check for GCC r10k-cache-barrier support
[MIPS] I8253: Export i2853_lock to modules.
[MIPS] VPE loader: Check result of memory allocation.
This patch fixes the compilation of the Au1000 XSS1500
board setup and irqmap code.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Work around the CPU clock miscalculation on Au1000DA/HA/HB due the
sys_cpupll register being write-only, i.e. actually do what the comment
before cal_r4off() function advertised for years but the code failed at.
This is achieved by just giving user a chance to define the clock
explicitly in the board config. via CONFIG_SOC_AU1000_FREQUENCY option,
defaulting to 396 MHz if the option is not given...
The patch is based on the AMD's big unpublished patch, the issue seems to
be an undocumented errata (or feature :-)...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Early 4KEc were MIPS32r1 and therefore need some love to get a TLB
refill handler.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- removed check for enable HT-PCI bridges, because some CFE version
init only the needed one and scanning works even with disabled HT
links
- implemented I/O access behind HT PCI busses
- fixed pci_map for IO resource behind PCI bridge
Tested with E100 and Tulip driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Check whether gcc supports -mr10-cache-barrier=1 and issue a cleaner
error message if not. This option is needed to build working SGI IP28
kernels.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And while at it, make it a little cleaner. Issue originally reported by
Tiejun Chen (tiejun.chen@windriver.com).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
as prescribed in Documentation/powerpc/booting-without-of.txt.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
This patch fixes USB malfunctioning on the MPC837xE-RDB boards.
Similar patch has been already applied for the MDS boards:
commit 28b9588592
Author: Li Yang <leoli@freescale.com>
Date: Thu Mar 6 18:42:26 2008 +0800
[POWERPC] 83xx: Fix wrong USB phy type in mpc837xmds dts
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch removes the unused include/asm-sh/floppy.h
(ARCH_MAY_HAVE_PC_FDC was not enabled).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some IOMMUs allocate memory areas spanning LLD's segment boundary limit. It
forces low level drivers to have a workaround to adjust scatter lists that the
IOMMU builds. We are in the process of making all the IOMMUs respect the
segment boundary limits to remove such work around in LLDs.
SPARC64 IOMMUs were rewritten to use the IOMMU helper functions and the commit
89c94f2f70 made the IOMMUs not allocate memory
areas spanning the segment boundary limit.
However, SPARC64 IOMMUs allocate memory areas first then try to merge them
(while some IOMMUs walk through all the sg entries to see how they can be
merged first and allocate memory areas). So SPARC64 IOMMUs also need the
boundary limit checking when they try to merge sg entries.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe http://bugzilla.kernel.org/show_bug.cgi?id=10318 is a false
positive. There's no way in which networking will be using highmem pages
here, so it won't be taking the KM_USER0 kmap slot, so there's no point in
performing these checks.
Cc: Pawel Staszewski <pstaszewski@artcom.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Really sad. We lose almost all real-life coverage of the debug tests
with this patch. Now it will only report problems for the cases where
people actually end up using a HIGHMEM page, not when they just _might_
use one. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes misprints in ITE 8152 interrupt demuxing
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ccoreutils and other have started using fstatat64. Thus, we
need a shim for it if we want to support modern oldabi
userlands (such as Debian/arm/lenny) with EABI kernels.
See http://bugs.debian.org/462677
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a bug in the powerpc DABR (data access breakpoint) handling,
which can result in us missing breakpoints if several threads are trying
to break on the same address.
The circumstances are that do_page_fault() calls do_dabr(), this clears
the DABR (sets it to 0) and sets up the signal which will report to
userspace that the DABR was hit. The do_signal() code will restore the DABR
value on the way out to userspace.
If we reschedule before calling do_signal(), __switch_to() will check the
cached DABR value and compare it to the new thread's value, if they match
we don't set the DABR in hardware.
So if two threads have the same DABR value, and we schedule from one to
the other after taking the interrupt for the first thread hitting the DABR,
the second thread will run without the DABR set in hardware.
The cleanest fix is to move the cache update into set_dabr(), that way we
can't forget to do it.
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Took some cycles to re-read the Lguest Journey end-to-end, fix some
rot and tighten some phrases.
Only comments change. No new jokes, but a couple of recycled old jokes.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Linus noticed a second bug and an uncleanliness:
- we'd return on any instruction fetch fault
- we'd use both the value of 16 and the PF_INSTR symbol which are
the same and make no sense
the cleanup nicely unifies this piece of logic.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'avr32-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix bug in early resource allocation code
avr32: Build fix for CONFIG_BUG=n
avr32: Work around byteswap bug in gcc < 4.2
We need to set up the shared_info pointer once we've mapped the real
shared_info into its fixmap slot. That needs to happen once the general
pagetable setup has been done. Previously, the UP shared_info was set
up one in xen_start_kernel, but that was left pointing to the dummy
shared info. Unfortunately there's no really good place to do a later
setup of the shared_info in UP, so just do it once the pagetable setup
has been done.
[ Stable: needed in 2.6.24.x ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
xen_irq_enable_direct and xen_sysexit were using "andw $0x00ff,
XEN_vcpu_info_pending(vcpu)" to unmask events and test for pending ones
in one instuction.
Unfortunately, the pending flag must be modified with a locked operation
since it can be set by another CPU, and the unlocked form of this
operation was causing the pending flag to get lost, allowing the processor
to return to usermode with pending events and ultimately deadlock.
The simple fix would be to make it a locked operation, but that's rather
costly and unnecessary. The fix here is to split the mask-clearing and
pending-testing into two instructions; the interrupt window between
them is of no concern because either way pending or new events will
be processed.
This should fix lingering bugs in using direct vcpu structure access too.
[ Stable: needed in 2.6.24.x ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The first page of the compound page is determined in follow_huge_addr()
but then PageCompound() only checks if the page is part of a compound page.
PageHead() allows checking if this is indeed the first page of the
compound.
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes the use of GPIO routines which are in the PCI
configuration space of the RDC321x, therefore reading/writing
to this space without spinlock protection can be problematic.
We also now request and free GPIOs and support the MGB100
board, previous code was very AR525W-centric.
Signed-off-by: Volker Weiss <volker@tintuc.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/ptrace.c:548: warning: 'ptrace_bts_get_size' defined but not used
arch/x86/kernel/ptrace.c:558: warning: 'ptrace_bts_read_record' defined but not used
arch/x86/kernel/ptrace.c:607: warning: 'ptrace_bts_clear' defined but not used
arch/x86/kernel/ptrace.c:617: warning: 'ptrace_bts_drain' defined but not used
arch/x86/kernel/ptrace.c:720: warning: 'ptrace_bts_config' defined but not used
arch/x86/kernel/ptrace.c:788: warning: 'ptrace_bts_status' defined but not used
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
some early Athlon XP's and Opterons generate bogus faults on prefetch
instructions. The workaround for this regressed over .24 - reinstate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add_reserved_region() tries to keep the resource list sorted, so when
looking for a place to insert the new resource, it may break out
before the last entry.
When this happens, the list is broken in two because the sibling field
of the new entry doesn't point to the next resource. Fix it by
updating the new resource's sibling field appropriately.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
fix the 3D performance drop reported at:
http://bugzilla.kernel.org/show_bug.cgi?id=10328
fb drivers are using ioremap()/ioremap_nocache(), followed by mtrr_add with
WC attribute. Recent changes in page attribute code made both
ioremap()/ioremap_nocache() mappings as UC (instead of previous UC-). This
breaks the graphics performance, as the effective memory type is UC instead
of expected WC.
The correct way to fix this is to add ioremap_wc() (which uses UC- in the
absence of PAT kernel support and WC with PAT) and change all the
fb drivers to use this new ioremap_wc() API.
We can take this correct and longer route for post 2.6.25. For now,
revert back to the UC- behavior for ioremap/ioremap_nocache.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we could call find_max_pfn() directly instead of setup_memory() to get
max_pfn needed for mtrr trimming.
otherwise setup_memory() is called two times... that is duplicated...
[ mingo@elte.hu: both Thomas and me simulated a double call to
setup_bootmem_allocator() and can confirm that it is a real bug
which can hang in certain configs. It's not been reported yet but
that is probably due to the relatively scarce nature of
MTRR-trimming systems. ]
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Wed, 26 Mar 2008 11:56:22 -0600
Jordan Crouse <jordan.crouse@amd.com> wrote:
> On 26/03/08 14:31 +0100, Stefan Pfetzing wrote:
> > Hello Jordan,
> >
> > I just tried to build your geodwdt driver for the geode watchdog. Therefore
> > I pulled your repository from http://git.infradead.org/geode.git (or more,
> > the git url).
> >
> > I tried to build the geodewdt driver as a module - which didn't work, and
> > it failed with the same problem as earlier mentioned on lkmk [1]. I also
> > checked the fix [2], but that seems to be already in your (or linus) tree -
> > and so I'm unsure what the problem is.
> >
> > [1] http://kerneltrap.org/mailarchive/linux-kernel/2008/2/17/884074
> > [2] http://kerneltrap.org/mailarchive/linux-kernel/2008/2/17/884174
> >
> > Building directly into the kernel seems to work.
> >
> > Maybe you have some idea?
>
> Hmm - that is strange. Exporting the symbols should work. I recommend
> starting over with a clean tree.
>
> CCing Andres - any thoughts?
>
> Jordan
>
Er, yeah. The patch below should fix it. This should probably go into
2.6.25.
Oops, EXPORT_SYMBOL_GPL wasn't being declared due to this header
being missing.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I have found that using SMI to change the cpu's frequency on my DELL
Latitude L400 clobbers the ECX register in speedstep_set_state, causing
unneccessary retries because the "state" variable has changed silently (GCC
assumes it is still present in ECX).
play safe and avoid gcc caching any register across IO port accesses
that trigger SMIs.
Signed-off by: <Stephan.Diestelhorst@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Convert function comment blocks to kernel-doc notation.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Presently with preempt enabled there's the possibility to be preempted
after the TIF_USEDFPU test and the register save, leading to bogus
state post-__switch_to(). Use an explicit preempt_disable()/enable()
pair around unlazy_fpu()/clear_fpu() to avoid this. Follows the x86
change.
Reported-by: Takuo Koguchi <takuo.koguchi.sw@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Sparse still doesn't like the funny cast we make from a scalar to a
"union semun" (which is correct by the C language and in particular
works with the sparc64 calling conventions, but sparse doesn't grok
that yet).
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'UL' markers to DCU_* macros.
Declare C functions called from assembler in entry.h
Declare C functions called from within the sparc64 arch
code in include/asm-sparc64/*.h headers as appropriate.
Remove unused routines in traps.c
Signed-off-by: David S. Miller <davem@davemloft.net>
IFF_ALLMULTI is an indication from the network stack to the driver
to disable multicast filters, drivers should never set it directly.
Since the UML networking device doesn't have any filtering capabilites,
it doesn't the set_multicast_list function at all, it is kept so userspace
can still issue SIOCADDMULTI/SIOCDELMULTI ioctls however.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a local header file entry.h, under arch/sparc64/kernel/,
that we can use to declare routines either defined in assembler
or only invoked from assembler. As well as other data objects
which are private to the inner sparc64 kernel arch code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable GEN_RTC since it conflicts with the i2c rtc drivers registering,
besides that keep most of the new defaults.
Signed-off-by: Olof Johansson <olof@lixom.net>
While backporting 72dc67a696, a gfn_to_page()
call was duplicated instead of moved (due to an unrelated patch not being
present in mainline). This caused a page reference leak, resulting in a
fairly massive memory leak.
Fix by removing the extraneous gfn_to_page() call.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Do not assume that a shadow mapping will always point to the same host
frame number. Fixes crash with madvise(MADV_DONTNEED).
[avi: move after first printk(), add another printk()]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The vmx hardware state restore restores the tss selector and base address, but
not its length. Usually, this does not matter since most of the tss contents
is within the default length of 0x67. However, if a process is using ioperm()
to grant itself I/O port permissions, an additional bitmap within the tss,
but outside the default length is consulted. The effect is that the process
will receive a SIGSEGV instead of transparently accessing the port.
Fix by restoring the tss length. Note that i386 had this working already.
Closes bugzilla 10246.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Doing a 'flushw' every stack trace capture creates so much overhead
that it makes lockdep next to unusable.
We only care about the frame pointer chain and the function caller
program counters, so flush those by hand to the stack frame.
This is significantly more efficient than a 'flushw' because:
1) We only save 16 bytes per active register window to the stack.
2) This doesn't push the entire register window context of the current
call chain out of the cpu, forcing register window fill traps as we
return back down.
Note that we can't use 'restore' and 'save' instructions to move
around the register windows because that wouldn't work on Niagara
processors. They optimize 'save' into a new register window by
simply clearing out the registers instead of pulling them in from
the on-chip register window backing store.
Based upon a report by Tom Callaway.
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip. Otherwise the driver won't find the device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix Oops with TQM5200 on TQM5200
[POWERPC] mpc5200: Fix null dereference if bestcomm fails to initialize
[POWERPC] mpc5200-fec: Fix possible NULL dereference in mdio driver
[POWERPC] Fix crash in init_ipic_sysfs on efika
[POWERPC] Don't use 64k pages for ioremap on pSeries
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: exec PT_DTRACE
[SPARC64]: Use shorter list_splice_init() for brevity.
[SPARC64]: Remove most limitations to kernel image size.
It appears that 64-bit PCI resources cannot possibly ever have worked on
x86-32 even when the RESOURCES_64BIT config option was set, because any
driver that tried to [pci_]ioremap() the resource would have been unable
to do so because the high 32 bits would have been silently dropped on
the floor by the ioremap() routines that only used "unsigned long".
Change them to use "resource_size_t" instead, which properly encodes the
whole 64-bit resource data if RESOURCES_64BIT is enabled.
Acked-by: H. Peter Anvin <hpa@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "bestcomm-core" driver defines its of_match table as follows
static struct of_device_id mpc52xx_bcom_of_match[] = {
{ .type = "dma-controller", .compatible = "fsl,mpc5200-bestcomm", },
{ .type = "dma-controller", .compatible = "mpc5200-bestcomm", },
{},
};
so while registering the driver, the driver's probe function won't be
called, because the device tree node doesn't have a device_type
property. Thus the driver's bcom_engine structure won't be allocated.
Referencing this structure later causes observed Oops.
Checking bcom_eng pointer for NULL before referencing data pointed
by it prevents oopsing, but fec driver still doesn't work (because
of the lost bestcomm match and resulted task allocation failure).
Actually the compatible property exists and should match and so
the fec driver should work.
This removes .type = "dma-controller" from the bestcomm driver's
mpc52xx_bcom_of_match table to solve the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the bestcomm initialization fails, calls to the task allocate
function should fail gracefully instead of oopsing with a NULL deref.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The global primary_ipic in arch/powerpc/sysdev/ipic.c can remain NULL
if ipic_init() fails, which will happen on machines that don't have an
ipic interrupt controller. init_ipic_sysfs() will crash in that case.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On pSeries, the hypervisor doesn't let us map in the eHEA ethernet
adapter using 64k pages, and thus the ehea driver will fail if 64k
pages are configured. This works around the problem by always
using 4k pages for ioremap on pSeries (but not on other platforms).
A better fix would be to check whether the partition could ever
have an eHEA adapter, and only force 4k pages if it could, but this
will do for 2.6.25.
This is based on an earlier patch by Tony Breeds.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PT_DTRACE flag is meaningless and obsolete.
Don't touch it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert
commit f62f1fc9ef
Author: Yinghai Lu <yhlu.kernel@gmail.com>
Date: Fri Mar 7 15:02:50 2008 -0800
x86: reserve dma32 early for gart
The patch has a dependency on bootmem modifications which are not .25
material that late in the -rc cycle. The problem which is addressed by
the patch is limited to machines with 256G and more memory booted with
NUMA disabled. This is not a .25 regression and the audience which is
affected by this problem is very limited, so it's safer to do the
revert than pulling in intrusive bootmem changes right now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently kernel images are limited to 8MB in size, and this causes
problems especially when enabling features that take up a lot of
kernel image space such as lockdep.
The code now will align the kernel image size up to 4MB and map that
many locked TLB entries. So, the only practical limitation is the
number of available locked TLB entries which is 16 on Cheetah and 64
on pre-Cheetah sparc64 cpus. Niagara cpus don't actually have hw
locked TLB entry support. Rather, the hypervisor transparently
provides support for "locked" TLB entries since it runs with physical
addressing and does the initial TLB miss processing.
Fully utilizing this change requires some help from SILO, a patch for
which will be submitted to the maintainer. Essentially, SILO will
only currently map up to 8MB for the kernel image and that needs to be
increased.
Note that neither this patch nor the SILO bits will help with network
booting. The openfirmware code will only map up to a certain amount
of kernel image during a network boot and there isn't much we can to
about that other than to implemented a layered network booting
facility. Solaris has this, and calls it "wanboot" and we may
implement something similar at some point.
Signed-off-by: David S. Miller <davem@davemloft.net>
so use nodedata_phys directly.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix the bug reported here:
http://bugzilla.kernel.org/show_bug.cgi?id=10232
use update_memory_range() instead of add_memory_range() directly
to avoid closing the gap.
( the new code only affects and runs on systems where the MTRR
workaround triggers. )
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
we have seen a little problem in rebooting Dell Optiplex 745 with the
0KW626 board. Here is a small patch enabling reboot with this board,
which forces the default reboot path it into the BIOS reboot mode.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The fault_msg text is not explictly nul terminated now in startup
assembly. Do so by converting .ascii to .asciz.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
aperture_64.c takes a piece of memory and makes it into iommu
window... but such window may not be saved by swsusp -- that leads to
oops during hibernation.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
this patch allows hpet=force on nVidia nForce 430 southbridge.
This patch was tested by me on my old Asus A8N-VM CSM (where bios does not
support hpet and does not advertise it via acpi entry). My nForce430 version:
lspci -nn | grep LPC
00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260]
(rev a2)
Kernel 2.6.24.3 after patching and using hpet=force reports this:
dmesg | grep -i hpet
Kernel command line: root=/dev/sda8 ro vga=773 video=vesafb:mtrr:4,ywrap
vt.default_utf8=0 hpet=force
Force enabled HPET at base address 0xfed00000
hpet clockevent registered
Time: hpet clocksource has been installed.
grep -i hpet /proc/timer_list
Clock Event Device: hpet
set_next_event: hpet_legacy_next_event
set_mode: hpet_legacy_set_mode
grep Clock /proc/timer_list (before patching)
Clock Event Device: pit
Clock Event Device: lapic
grep Clock /proc/timer_list (after patching)
Clock Event Device: hpet
Clock Event Device: lapic
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
a system with 256 GB of RAM, when NUMA is disabled crashes the
following way:
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Cannot allocate aperture memory hole (ffff8101c0000000,65536K)
Kernel panic - not syncing: Not enough memory for aperture
Pid: 0, comm: swapper Not tainted 2.6.25-rc4-x86-latest.git #33
Call Trace:
[<ffffffff84037c62>] panic+0xb2/0x190
[<ffffffff840381fc>] ? release_console_sem+0x7c/0x250
[<ffffffff847b1628>] ? __alloc_bootmem_nopanic+0x48/0x90
[<ffffffff847b0ac9>] ? free_bootmem+0x29/0x50
[<ffffffff847ac1f7>] gart_iommu_hole_init+0x5e7/0x680
[<ffffffff847b255b>] ? alloc_large_system_hash+0x16b/0x310
[<ffffffff84506a2f>] ? _etext+0x0/0x1
[<ffffffff847a2e8c>] pci_iommu_alloc+0x1c/0x40
[<ffffffff847ac795>] mem_init+0x45/0x1a0
[<ffffffff8479ff35>] start_kernel+0x295/0x380
[<ffffffff8479f1c2>] _sinittext+0x1c2/0x230
the root cause is : memmap PMD is too big,
[ffffe200e0600000-ffffe200e07fffff] PMD ->ffff81383c000000 on node 0
almost near 4G..., and vmemmap_alloc_block will use up the ram under 4G.
solution will be:
1. make memmap allocation get memory above 4G...
2. reserve some dma32 range early before we try to set up memmap for all.
and release that before pci_iommu_alloc, so gart or swiotlb could get some
range under 4g limit for sure.
the patch is using method 2.
because method1 may need more code to handle SPARSEMEM and SPASEMEM_VMEMMAP
will get
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Memory: 264245736k/268959744k available (8484k kernel code, 4187464k reserved, 4004k data, 724k init)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We recently got some of the "Desktop Form Factor" Optiplex 745's in. I
noticed that there's an entry for the SFF one's, but the BIOS model number
of the DFF differs from that of the SFF. We have been reliably
experiencing the same (as far as I can tell) reboot bug as the SFF boxes.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix visws printk format warnings:
/local/linsrc/linux-2.6.24-git15/arch/x86/mach-visws/traps.c:50: warning: format '%#lx' expects type 'long unsigned int', but argument 2 has type 'u32'
/local/linsrc/linux-2.6.24-git15/arch/x86/mach-visws/traps.c:50: warning: format '%#lx' expects type 'long unsigned int', but argument 3 has type 'u32'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
when numa disabled I got this compile warning:
arch/x86/kernel/setup64.c: In function setup_per_cpu_areas:
arch/x86/kernel/setup64.c:147: warning: the address of
contig_page_data will always evaluate as true
it seems we missed checking if the node is online before we try to refer
NODE_DATA. Fix it.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
memory-less node support:
this patch uses updated dev_to_node, because dev_to_node already makes sure
it returns an online node.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.25:
sh: Use relative paths for mach/cpu symlinks.
SH: Use newer, non-deprecated __SPIN_LOCK_UNLOCKED macro.
sh: Fix more user header breakage from sh64 integration.
sh: Fix uImage build error.
sh: Fix up the timer IRQ definition for SH7203.
sh: Fix up the address error exception handler for SH-2.
serial: sh-sci: Fix fifo stall on SH7760/SH7780/SH7785 SCIF.
When building the kernel without passing the O= command line parameter
there's no point to use absolute paths for them.
Usually relative paths are preferred because they survive directory
moves, work across networked file systems and chrooted environments.
Absolute paths are still used if an output directory is given.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
a0c1e9073e "futex: runtime enable pi and
robust functionality" introduces a test wether futex in atomic stuff
works or not.
It does that by writing to address 0 of the kernel address space. This
will crash on older machines where addressing mode switching is enabled
but where the mvcos instruction is not available. Page table walking is
done by hand and therefore the code tries to access current->mm which
is NULL.
Therefore add an extra check, so we survive the early test.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
fix signal return code when enable CONFIG_OABI_COMPAT
Signed-off-by: Janboe Ye <janboe.ye@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the code required to register the F75375 device on the
GLAN Tank.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some bootloaders are disabling write buffer coalescing. Enable it back
under linux.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes the return value of omap_dma_chain_a_transfer
to 0 on success instead of the flag 'start_dma', which wasn't really useful
for anything.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although audio and dsp drivers are not integrated yet,
allow compiling in mailbox and mcbsp to see any build
warnings.
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO IRQ unmask doesn't actually do anything useful. The problem is
hidden by a separate explicit mass unmask at the end of the chained
bank handler.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One-shot mode was broken in MPU-timer support for OMAP1 due to a typo.
Also, ensure timer is stopped before changing the auto-reload flag.
The TRM says changing the AR flag when timer is running is undefined.
Also set GENERIC_CLOCKEVENTS for all omaps.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PCI bridge representing the PCIE root complex on Axon, contains
device BARs for a memory range and ROM that define inbound accesses.
This confuses the kernel resource management code -- the resources
need to be hidden when Axon is a host bridge.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The cell IOMMU code to parse the dma-ranges properties, used for the fixed
mapping, was broken in two ways for some devices.
Firstly it didn't cope with empty dma-ranges properties. An empty property
implies no translation so can be safely skipped.
The code also wrongly assumed it would be looking at PCI devices, and hard
coded the number of address and size cells.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The wrapper script didn't have entries for the TQM8540 board and the
SBC8548 or SBC8560 boards. I've assumed that the TQM8540 console is
8250 based and not CPM based by looking at its defconfig. There was
also a trailing * on the TQM8555 entry that I removed too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the PMU is an NMI now, it can come at any time we are only soft
disabled. We must hard disable around the two places we allow the kernel
stack SLB and r1 to go out of sync. Otherwise the PMU exception can
force a kernel stack SLB into another slot, which can lead to it
getting evicted, which can lead to a nasty unrecoverable SLB miss
in the exception entry code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PTRACE_SETREGS request was only recently added on powerpc,
and gdb does not use it. So it slipped through without getting
all the testing it should have had.
The user_regset changes had a simple bug in storing to all of
the 32-bit general registers block on 64-bit kernels. This bug
only comes up with PTRACE_SETREGS, not PPC_PTRACE_SETREGS.
It causes a BUG_ON to hit, so this fix needs to go in ASAP.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- move boot_args[] into the init section
- move $global$ into the read_mostly section
- fix the following two section mismatches:
WARNING: vmlinux.o(.text+0x9c): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
WARNING: vmlinux.o(.text+0xa0): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
Signed-off-by: Helge Deller <deller@gmx.de>
SIgned-off-by: Kyle McMartin <kyle@mcmartin.ca>
When we show_regs, we obviously have a struct pt_regs of the calling
frame. Use these in show_stack so we don't have the entire bogus call trace
up to the show_stack call.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This patch adds the known pa8900 CPUs to the inventory list and removes
the Crestone Peak one which apparently never escaped into the wild.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This patch moves the default parisc defconfig to
arch/parisc/configs/generic_defconfig where it belongs and selects it as
the default defconfig through KBUILD_DEFCONFIG.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Commit 721fdf3416 introduced a subtle bug
by accidently removing the "static" from iodc_dbuf. This resulted in, what
appeared to be, a trap without *current set to a task. Probably the result of
a trap in real mode while calling firmware.
Also do other misc clean ups. Since the only input from firmware is non
blocking, share iodc_dbuf between input and output, and spinlock the
only callers.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Originally, show_stack was used in BUG() output. However, a recent commit
changed it to print register state (no idea what that's supposed to help,
really...) and parisc was missing a backtrace because of it.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The printf string was broken in the same way the zImage one was before,
though the uImage managed to avoid getting fixed at that time. Do so now.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Don't include the BUG trap handling code when CONFIG_BUG is not set.
This fixes allnoconfig.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (32 commits)
ACPI: thermal: show temperature in millidegree Celsius
thermal: fix generic thermal I/F for hwmon
acer-wmi: build depends on i8042
documentation: Move power-related files to Documentation/power/
ACPI: buffer array too short in drivers/acpi/system.c
acer-wmi: Add DMI quirk for mail LED support on Acer Aspire 3610/ 5610
acer-wmi: Fix DSDT path in documentation
acer-wmi: Make device detection error messages more descriptive
laptops: move laptop-mode.txt to Documentation/laptops/
ACPICA: Warn if packages with invalid references are evaluated
ACPI: add _PRT quirks to work around broken firmware
Hibernation: Fix mark_nosave_pages()
ACPI: Ignore _BQC object when registering backlight device
ACPI: WMI: Clean up handling of spec violating data blocks
acer-wmi: Don't warn if mail LED cannot be detected
acer-wmi: Rename mail LED correctly & remove hardcoded colour
ACPI: use ACPI_DEBUG_PRINT instead of printk in acpi_processor_hotplug_notify()
ACPI: button: make real parent for input devices in device tree
toshiba_acpi: Enable autoloading
ACPI: EC: Handle IRQ storm on Acer laptops
...
iommu_is_span_boundary in lib/iommu-helper.c was exported for PARISC IOMMUs
(commit 3715863aa1). Alpha's IOMMU can use it.
This removes the check on the boundary size alignment because
iommu_is_span_boundary does.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
