Here is a patch for a new PID (zeitcontrol-device mifare-reader FT232BL(like FT232BM but lead free)).
Signed-off-by: Artur Zimmer <artur128@3dzimmer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the recent addition of the FT232H showed that baudrate was set wrong. See
gmane.linux.usb.general: "[ftdi_sio] FT232H support". With the old code,
the MSB of the 4 encoded fractional divider bits and more important the
clock predivider bits got lost. Adding the FT232H to the code patch were
these bits are shifted solves the problem. I verified baud rates with a
scope now.
I suspect, that the BM device probably needs these bits shifted too. But
there is no predivider bit, so this is not obvious, and a missing MSB of the
encoded fractional divider only shifts the resulting baudrate minimal.
The AM has only 3 bits of encoded fractional divider, so it is not impacted.
I have no BM device to test, so I only added a comment and left the code for
the BM untouched.
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Even if it's unlikely for this to cause an error,
there is a typo in the code that uses the bitwise-AND
operator instead of the logical one.
Signed-off-by: Ionut Nicu <ionut.nicu@cloudbit.ro>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
appended patch adds support for the new FTDI FT232H chip. This chip is a
single channel version of the dual FT2232H/quad FT4232H, coming with it's
own default PID 0x6014 (FT2232H uses the same PID 0x6010 like FT2232C,
FT4232H has also it's own PID).
The patch was checked on an UM232H module and a terminal program with TX/RX
shorted to that typing in the terminal reproduced the characters.
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding support for the TavIR STK500 (id 0403:FA33)
Atmel AVR programmer device based on FTDI FT232RL.
Signed-off-by: Benedek László <benedekl@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb serial: ftdi_sio: add two missing USB ID's for Hameg interfaces HO720
and HO730
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PID 0x0103 for serial port of the OCT DK201 docking station.
Reported-by: Jan Hoogenraad <jan@hoogenraad.net>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I added new ProdutIds for two devices from CTI GmbH Leipzig.
Signed-off-by: Christian Simon <simon@swine.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
Adding support for the OLIMEX ARM-USB-OCD-H JTAG device (id 15ba:002b)
based on FTDI FT2232H
Signed-off-by: JF Argentino <jf.argentino@free.fr>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't use it so we can trim it from here as we try and stamp the file
object dependencies out of the serial code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB Vendor ID and Product ID for a Acton Research Corp.
spectrograph device with a FTDI chip for serial I/O.
Signed-off-by: Michael H Williamson <michael.h.williamson@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
on ST Micro Connect Lite we have 4 port
Part A and B for the JTAG
Port C Uart
Port D for PIO
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 2232H high speed baud rates also support fractional baud
rate divisors, but when the performing the divisions before
the multiplication, the fractional bits are lost.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Acked-by: Mark Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found the original patch on the db0fhn repeater wiki (couldn't find the email
of the origial author) I guess it was never commited.
I updated and added some Icom HAM-radio devices to the ftdi driver.
Added extra comments to make clear what devices it are.
Signed-off-by: Pieter Maes <maescool@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Willem-Jan noticed that the ftdi_sio driver did not support the
TIOCSERGETLSR ioctl, and some userspace programs rely on it. This patch
adds the support.
Reported-by: Willem-Jan de Hoog <wdehoog@exalondelft.nl>
Tested-by: Willem-Jan de Hoog <wdehoog@exalondelft.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the PID for the Vardaan Enterprises VEUSB422R3 USB to RS422/485
converter. It uses the same chip as the FTDI_8U232AM_PID 0x6001.
This should also work with the stable branches for:
2.6.31, 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36
Signed-off-by: Jacques Viviers <jacques.viviers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another variant of the RT Systems programming cable for ham radios.
Signed-off-by: Michael Stuermer <ms@mallorn.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB IDs for the Milkymist One FTDI-based JTAG/serial adapter
(http://projects.qi-hardware.com/index.php/p/mmone-jtag-serial-cable/)
to the ftdi_sio driver and disable the first serial channel (used as
JTAG from userspace).
Signed-off-by: Sebastien Bourdeauducq <sebastien@milkymist.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
This adds the requested device ids to the ftdi_sio driver.
Reported-by: Ewan Bingham <ewan@auc.co.uk>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No need to set latency timeout at every open.
This also fixes an issue with the read latency being as high as 250ms
(instead of 1ms) for the first read after port probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for FTDI USB serial driver ads new VID/PIDs used on various
devices manufactured by Papouch (http://www.papouch.com). These devices
have their own VID/PID, although they're using standard FTDI chip. In
ftdi_sio.c, I also made small cleanup to have declarations for all
Papouch devices together.
Signed-off-by: Daniel Suchy <danny@danysek.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OpenDCC project is developing a new hardware. This patch adds its
PID to the list of known FTDI devices. The PID can be found at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
Signed-off-by: Rainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 6a1a82df91.
RTS and DTR should not be modified based on CRTSCTS when calling
set_termios.
Modem control lines are raised at port open by the tty layer and should stay
raised regardless of whether hardware flow control is enabled or not.
This is in conformance with the way serial ports work today and many
applications depend on this behaviour to be able to talk to hardware
implementing hardware flow control (without the applications actually using
it).
Hardware which expects different behaviour on these lines can always
use TIOCMSET/TIOCMBI[SC] after port open to change them.
Reported-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Dave Mielke <dave@mielke.cc>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for Accesio USB to Serial adapters, which are built around
FTDI FT232 UARTs. Tested with the Accesio USB-COM-4SM.
Signed-off-by: Rich Mattes <richmattes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simple pasting job using the new ops function. Also fix a couple of devices
directly returning the internal struct (which happens at this point to match
for the fields that matter but isn't correct or futureproof)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ftdi product ID for Lenz LI-USB, a model train interface. This
was NOT tested against 2.6.35, but a similar patch was tested with the
CentOS 2.6.18-194.11.1.el5 kernel. It wasn't clear to me what
ordering is being used in ftdi_sio.c, so I inserted the ID after another
model train entry(SPROG_II).
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the ID for the Ionics PlugComputer (<http://ionicsplug.com/>).
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB max packet size (always little-endian) was not being byte
swapped on big-endian systems.
Applicable since [USB: ftdi_sio: fix hi-speed device packet size calculation] approx 2.6.31
Signed-off-by: Michael Wileczka <mikewileczka@yahoo.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since handle_sysrq() does not take tty as argument anymore we can
drop it from usb_serial_handle_sysrq_char() as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch is to add a US Interface, Inc. "Navigator" USB device.
Specifically, it's a HAM Radio USB sound modem that also
incorporates three pairs of unique FTDI serial ports. The standard
Linux FTDI serial driver will only recognize the first two serial
ports of an unknown FDTI derived device and this patch adds in
recognition to these specific new IDs.
Signed-off-by: David A. Ranch <dranch@trinnet.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have added the ProductID=0xe729 VendorID=FTDI_VID=0x0403 which will
enable support for the Segway Robotic Mobility Platform (RMP200) in the
ftdi_sio kernel module. Currently, users of the Segway RMP200 must use
a RUN+="/sbin/modprobe -q ftdi-sio product=0xe729 vendor=0x0403 in a
udev rule to get the ftdi_sio module to handle the usb interface and
mount it on /dev/ttyXXX. This is not a good solution because some users
will have multiple USB to Serial converters which will use the ftdi_sio
module.
Signed-off-by: John Rogers <jgrogers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg prefers this to go through the trivial tree.
http://lkml.org/lkml/2010/6/24/1
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Moved a statement down a line in drivers/usb/host/u132-hcd.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
RT Systems has put out bunch of ham radio cables based on the FT232RL
chip. Each cable type has a unique PID, this adds one for the Yaesu VX-7
radios.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: support for Signalyzer tools based on FTDI chips
This patch adds support for the Xverve Signalyzers.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects a problem with the merge of a previous
patch to add the CONTEC identifier.
I believe the merge problem occurred with the commit:
dee5658b48
Originally I submitted a patch and then they asked me to order the IDs
and resubmit, so did I. But unfortunately in the end somehow both
patches were merged.
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call set_mctrl() and clear_mctrl() according to the flow control mode
selected. This makes serial communication for FT232 connected devices
work when CRTSCTS is not set.
This fixes a regression introduced by 4175f3e31 ("tty_port: If we are
opened non blocking we still need to raise the carrier"). This patch
calls the low-level driver's dtr_rts() function which consequently sets
TIOCM_DTR | TIOCM_RTS. A later call to set_termios() without CRTSCTS in
cflags, however, does not reset these bits, and so data is not actually
sent out on the serial wire.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
