In case of failure the return value was always 0. Return proper
error code (ENODEV) instead.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Improve scanning performance by setting property 0301 with a value
from Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds symbol rate setting to the driver.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Print notice on driver load: "SDR API is still slightly
experimental and functionality changes may follow". It is just
remind possible used SDR API is very new and surprises may occur.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move it out of staging into media like all the other SDR drivers
too. There is no good reasons to keep these SDR drivers in staging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SDR API is very new and surprises may occur. Due to that print
notice to remind possible users.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move emulated format behind module parameter as those are not
supported. Format conversions will be on library eventually.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mirics MSi001 and MSi2500 drivers uses SPI bus. Due to that we need
auto-select it too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add software defined radio device support for media Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement unlocked variants of v4l2_ctrl_s_ctrl() and
v4l2_ctrl_s_ctrl_int64(). As drivers need to set controls as they access
driver internal state elsewhere than in the control framework unlocked
variants of these functions become handy.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Drivers may use the v4l2_ctrl_modify_range() internally as part of other
operations that need to be both serialised using a driver's lock which can
also be used to serialise access to the control handler. Provide an unlocked
version of the function, __v4l2_ctrl_modify_range() which then may be used
by drivers for the purpose.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fall-out from the recent struct v4l2_framebuffer change.
drivers/media/common/saa7146/saa7146_fops.c: In function ‘saa7146_vv_init’:
drivers/media/common/saa7146/saa7146_fops.c:536:6: warning: assignment from incompatible pointer type [enabled by default]
fmt = &vv->ov_fb.fmt;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver moved over to v4l2_async_unregister_subdev()
but still retained a call to v4l2_unregister_subdev(). Remove.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CPB size is limited by the hardware. Add this limit to the s_fmt.
Signed-off-by: panpan liu <panpan1.liu@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
OVL and BTP IRAM buffers are never used, setup the bits for
for DBK/BIT/IP usage depending on CODA version in one place.
Also, use a simple allocator function and group IRAM addresses
and size in a coda_aux_buf structure.
This is done in preparation for CODA960 support.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If bitrate is not set, the encoder is running in VBR mode, with the
I- and P-frame quantization parameters configured from userspace.
For the quantization parameters, 0 is a valid value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently the rotator unit is used to copy decoded frames out into buffers
provided by videobuf2. Since the CODA reports the I/P/B frame type of the
last decoded frame, and this frame will be copied out in a later device_run,
depending on display order, we have to store the frame type until such time.
This patch also adds the B-frame type.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
fc906b6d "Remove special clock usage in driver" removed
initialization of MFC special clock, arguing that there's
no need to do it explicitly, since it's one of MFC gate clock's
dependencies and gets enabled along with it. However, there's
no promise of keeping this hierarchy across Exynos SoC
releases, therefore this approach fails to provide a stable,
portable solution.
Out of all MFC versions, only v6 doesn't use special clock at all.
For other versions log a message only in case clk_get fails,
as not all the devices with the same MFC version require
initializing the clock explicitly.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the s5p_mfc_alloc_firmware() function there are some mistakes
where the code checks whether the DMA memory is properly allocated or
not.
First of all dma_alloc_coherent() returns NULL in case of error.
The code also checked two times fw_virt_addr, ignoring
the bank2_virt pointer.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ZR050_MO_COMP define is cut and pasted twice so we can delete the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the null test on dvb. dvb is initialized at the
beginning of the function to &port->dvb. Since port is dereferenced
prior to the null test, port must be a valid pointer, and
&port->dvb cannot be null.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The issue was discovered by static analysis. It turns out that code is
somewhat insane, being
if (x) {...} else { if (x) {...} }
Edited it to do the only reasonable thing, which is to log the
information about the failed call. The most descriptive logging commands
set is taken from original code.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79801
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The colorspace for HDTV is REC709, not SMPTE240M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for Hauppauge model 71100: WinTV-ImpactVCB-e
(PCIe, Retail, half height)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Otherwise you cannot get the current clip and bitmap information from
an overlay.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the vidioc_cropcap op is implemented by the driver then the v4l2
core will call that directly.
If g_selection is available, then the core cropcap implementation
uses g_selection to fill in the bounds and defrect and it sets the
pixelaspect to 1x1.
But if both are available, then I would like to use g_selection to
fill in defrect and bounds before calling cropcap. That way the
driver's cropcap implementation doesn't have to set defrect or
bounds.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Be sure that the reserved fields are cleared.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The edid field is the last field of the struct, so there is nothing to clear.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some applications poll a lot, so prevent the poll message from flooding
the log.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VIDIOC_STREAMON/OFF ioctls are not valid for radio devices, just
like the other streaming I/O ioctls. Add the streamon/off ioctls
to the other streaming I/O ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the driver supports enum_freq_bands, but only for certain device
nodes, then it may return -ENOTTY. But in that case the code should
fall into the fall-back case where the current tuner/modulator range
is returned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The other format ioctls (g/s/try_fmt) all check if the passed buffer type
makes sense for the device node's vfl_type. E.g. it makes no sense for a
VBI buffer type to be passed through a video node instead of a vbi node.
But this check was missing in ENUM_FMT which can cause a problem if you
have both video and sdr device nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a fatal error occurs that render the device unusable, the only
options for a driver to signal the error condition to userspace is to
set the V4L2_BUF_FLAG_ERROR flag when dequeuing buffers and to return an
error from the buffer prepare handler when queuing buffers.
The buffer error flag indicates a transient error and can't be used by
applications to detect fatal errors. Returning an error from vb2_qbuf()
is thus the only real indication that a fatal error occurred. However,
this is difficult to handle for multithreaded applications that requeue
buffers from a thread other than the control thread. In particular the
poll() call in the control thread will not notify userspace of the
error.
This patch adds an explicit mechanism to report fatal errors to
userspace. Drivers can call the vb2_queue_error() function to signal a
fatal error. From this moment on, buffer preparation will return -EIO to
userspace, and vb2_poll() will set the POLLERR flag and return
immediately. The error flag is cleared when cancelling the queue, either
at stream off time (through vb2_streamoff) or when releasing the queue
with vb2_queue_release().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The V4L2 specification states that
"When the application did not call VIDIOC_QBUF or VIDIOC_STREAMON yet
the poll() function succeeds, but sets the POLLERR flag in the revents
field."
The vb2_poll() function sets POLLERR when the queued buffers list is
empty, regardless of whether this is caused by the stream not being
active yet, or by a transient buffer underrun.
Bring the implementation in line with the specification by returning
POLLERR if no buffer has been queued only when the queue is not
streaming. Buffer underruns during streaming are not treated specially
anymore and just result in poll() blocking until the next event.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pixel color components can be scaled using either bilinear interpolation
or a multitap filter. The multitap filter provides better results, but
can't be selected when the alpha layer need to be scaled down by more
than 1/2.
Disable alpha scaling when the input has a fixed alpha value, and
program the UDS to output a fixed alpha value in that case. This ensures
the multitap filter will be used whenever possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Expose the background color to userspace through the V4L2_CID_BG_COLOR
control.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The BRU outputs premultiplied colors, enable color data normalization
when the format configured at the output of the pipeline isn't
premultiplied.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adjust the BRU blending formula to avoid the multiplication by alpha
when the corresponding input format is premultiplied. As this requires
access to the RPFs connected to the BRU inputs from the BRU module,
store pointers to the RPFs in the BRU structure when validating the
pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The control is used to configure the fixed alpha channel value, when
reading from memory in the RPF or writing to memory in the WPF.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Support ARGB formats on the RPF side by reading the alpha component from
memory and on the WPF side by writing it to memory.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver ignores the alpha component on output video nodes and
hardcodes the alpha component to 0 on capture video nodes. Make this
explicit by exposing XRGB formats.
Compatibility with existing userspace applications is handled by
selecting the XRGB format corresponding to the requested old RGB format.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 stores the video pipelines' input (RPF) to output (WPF)
mappings in a WPF register. An RPF must never be associated with
multiple WPFs, even if all of those WPFs but one are unused, otherwise
the hardware won't function properly.
The driver doesn't ensure this correctly as it never clears the
mappings. An RPF used with one WPF and later with a different WPF will
lead to malfunction, as it will be associated with two WPFs. Clear the
mappings at stream off time to fix this.
Reported-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the subdev pointer directly to_vsp1_pipeline() macro instead of
casting from the subdev to the wpf object and back to the subdev.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The control value is currently stored in the SRU structure by the
control set handler and written to the hardware at stream on time,
making control set during streaming ineffective. Fix it by writing to
the registers from within the control set handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The default value isn't set and defaults to 0, which isn't in the 1-6
min-max range. Fix it by setting the default value to 1.
This shoud have been caught when checking the control handler error
field at initialization time, but the check was missing. Add it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When setting a control directly on a subdev node the VSP1 driver doesn't
guarantee that the device is powered on. This leads to crashes when the
control handlers writes to hardware registers. One easy way to fix this
is to ensure that the device gets powered on when a subdev node is
opened. However, this consumes power unnecessarily, as there's no need
to power the device on when setting formats on the pipeline.
Furthermore, control handler setup at entity init time suffers from the
same problem as the device isn't powered on easier.
Fix this by extend the entity base object to setup the control handler
automatically when starting the stream. Entities must then skip writing
to registers in the set control handler when not streaming, which can be
tested with the new vsp1_entity_is_streaming() helper function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
