Since serial devices are powered down when not in use and some of those
devices cannot be accessed when powered down, we need to enable power
around calls to get_mcrtl() when dumping port state via uart_line_info().
This resolves hangs observed on some machines while reading serial device
registers when a port is powered off.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return failure immediately, so we don't have to test it twice.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch below works around a minor bug found in the UART of the remote
management card used in many HP ia64 and parisc servers (aka the Diva
UARTs). The problem is that the UART does not reassert the THRE interrupt
if it has been previously cleared and the IIR THRI bit is re-enabled. This
can produce a very annoying failure mode when used as a serial console,
allowing a boot/reboot to hang indefinitely until an RX interrupt kicks it
into working again (ie. an unattended reboot could stall).
To solve this problem, a backup timer is introduced that runs alongside the
standard interrupt driven mechanism. This timer wakes up periodically,
checks for a hang condition and gets characters moving again. This backup
mechanism is only enabled if the UART is detected as having this problem,
so systems without these UARTs will have no additional overhead.
This version of the patch incorporates previous comments from Pavel and
removes races in the bug detection code. The test is now done before the
irq linking to prevent races with interrupt handler clearing the THRE
interrupt. Short delays and syncs are also added to ensure the device is
able to update register state before the result is tested.
Aristeu says:
this was tested on the following HP machines and solved the problem:
rx2600, rx2620, rx1600 and rx1620s.
hpa says:
I have seen this same bug in soft UART IP from "a major vendor."
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This can be used for serial ports that are connected to an
OF platform bus but are not autodetected by the lecacy
serial support.
It will automatically take over devices that come from the
legacy serial detection, which usually is only one device.
In some cases, rtas may be set up to use the serial port
in the firmware, which allows easier debugging before probing
the serial ports. In this case, the "used-by-rtas" property
must be set by the firmware. This patch also adds code to the
legacy serial driver to check for this.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Access to chip-internal registers should always be native-endian. This is
especially important for AVR32 since it's a big-endian architecture and the
non-raw readl() and writel() macros are defined to do little-endian
accesses.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the CPCI-ASIO4 quad port CompactPCI UART board from
electronic system design gmbh.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get the Perle quad-modem PCI card (PCI-RAS4) detected by serial driver. It
may also get the PCI-RAS8 running, but can't guarantee as I didn't had one for
testing.
Signed-off-by: Thomas Hoehn <thomas.hoehn@avocent.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the serial_txx9 driver.
* Configurable manumum port number. (SERIAL_TXX9_NR_UARTS)
* Remove some code which is unneeded if CONFIG_PM=n.
* Use PCI_DEVICE() for pci device id table and make it const.
* Do not include <asm/irq.h>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SGI IOC3 and IOC4 PCI devices implement memory space apertures, not I/O
space apertures. Use the appropriate region management functions.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Stanislaw Skowronek <skylark@linux-mips.org>
Cc: Brent Casavant <bcasavan@sgi.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If RTS interrupt is caused by RTS senzing logic inside i.MX UART module the
IRQ type cannot be set.
It applies only for interrupts going through GPIO layer. The problem has
been noticed by Konstantin Kletschke some time ago.
No IRQF_TRIGGER set_type function for IRQ 26 (MPU)
I would not change type to fixed 0, because it could be possible to use
different GPIO MX1 pin for RTS in the theory. On the other hand it is only
for documentation purposes now, because RTS read code would have to be
adjusted in such case.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix occasional tx buffer overflows in the i.MX serial driver which came
from the fact that space in the buffer was checked after sending the first
byte. Also, fifosize is 32 bytes, not 8.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Atmel AT91 and AVR32 processor architectures share many of the same
peripherals. The PDC (Peripheral Data Controller) registers are also
implemented within in a number of the on-chip peripherals (eg, USART,
MMC, SPI, SSC, etc).
In a attempt not to duplicate the register definitions in each
peripheral, or in each architecture, the at91_pdc.h header in
asm-arm/arch-at91 and asm-avr32/arch-at32ap has been replaced with
linux/atmel_pdc.h.
The definitions have also been renamed from AT91_PDC_* to ATMEL_PDC_*,
and the drivers updated accordingly.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the
current kernel. Current patch fixes it, as well as other inconsistencies
expressed, that do not permit targets from working properly:
- Updated dts with a chosen node with interrupt controller,
- fixed messed device IDs among CPM2 SoC devices,
- corrected odd header name and fixed type in defines,
- Added 82xx subdir to the powerpc/platforms Makefile, missed during
initial commit,
- new solely-powerpc header file for 8260 family (was using one from
arch/ppc, this one cleaned up from the extra stuff), in fact for now
a placeholder to get the board-specific includes for stuff not yet
capable to live with devicetree peeks only
- Fixed couple of misprints in reference mpc8272 dts.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes cpm uart able to work using OF-passed parameters
in case of CPM stuff (found on most mpc8xx reference and custom
boards). The idea is to keep ppc stuff working yet making it able to be
used for powerpc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using console=ttyAM1 or console=ttyAMA1 resulted in an oops during
boot due to trying to drive the console before that port had been
registered. Fix this by checking whether the port is present before
allowing console setup to proceed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the unbalanced calls to enable_irq_wake() and
disable_irq_wake() in the AT91 (and AVR32) serial driver.
It should resolve these kernel messages:
Unbalanced IRQ x wake disable
BUG: warning at kernel/irq/manage.c:167/set_irq_wake()
Original patch from Marc Pignat.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A couple of whitespace cleanups, mainly in the AT91 header files.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y
and serial console support is enabled.
o Serial console setup function, serial8250_console_setup(), is a non __init
function and it calls functions which are of type __init().
(uart_parse_options() and uart_set_options()). Assuming, setup will
be called during init time, changing serial8250_console_setup() to __init.
o Adding one more pattern to modpost whitelist. Console drivers might
have *_console structures containing references to setup functions which
can be of __init type. Don't generate warnings for those.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The mpc52xx_uart_of_enumerate() function was added when adding 52xx
support to arch/powerpc, but it must not be called for arch/ppc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to pass in the resource otherwise we cannot
release the region properly. We must know whether it is
an I/O or MEM resource.
Spotted by Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
The uartlite driver used to always enable the port even if request_port
failed causing havoc. This patch fixes it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds initial support to 8250-pci for the Korenix Jetcard PCI serial
cards. The JC12xx cards are standard RS232-based serial cards utilising
the Oxford 16C950 device.
The JC14xx are RS422/RS485-based cards, but in order for these to be
supported natively, we will need additional tweaks to the 8250 layers so
we can specify some values for the 950's registers. Hence, these two
entries are commented out.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
Fix inotify maintainers entry
Fix typo in new debug options.
Jon needs a new shift key.
fs: Convert kmalloc() + memset() to kzalloc() in fs/.
configfs.h: Remove dead macro definitions.
kconfig: Standardize "depends" -> "depends on" in Kconfig files
e100: replace kmalloc with kcalloc
um: replace kmalloc+memset with kzalloc
fix typo in net/ipv4/ip_fragment.c
include/linux/compiler.h: reject gcc 3 < gcc 3.2
Kconfig: fix spelling error in config KALLSYMS help text
Remove duplicate "have to" in comment
Fix small typo in drivers/serial/icom.c
Use consistent casing in help message
EXT{2,3,4}_FS: remove outdated part of the help text
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Refactor Kconfig content to maximize nesting of menus by menuconfig and
xconfig.
Tested by simultaneously running `make xconfig` with and without
patch, and comparing displays.
Signed-off-by: Don Mullis <dwm@meer.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Willy pointed out the hversion is already stored
in the parisc_device, so I do not need to extract
this information directly from the IODC data.
Also by using the information in the parisc_device
I can avoid re-reading the IODC data for the Muxes
with specifed port counts.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch adds a new function to return the actual number
of ports available. Some of the built-in Muxes return the
number of supported ports, but not all of these port are
available for use.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch follows the example of the 8250_gsc
driver by probing for specific built-in Mux
cards first. This allows the system to preserve
the correct detection order with multiple Mux
cards.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The following updates are based off a patch from willy:
* Removal of the mux_card list.
* Add the mux_remove function.
Other updates:
* Re-organize the driver structure a bit to make the
mux_init and mux_exit functions more symmetrical.
* Added the del_timer.
* Unregistered the console.
At this point I can insmod, rmmod, and re-insmod the
mux without any failures.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch claims the iomem resources
for the Mux driver.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch changes the Mux console to
use the Mux hardware instead of the PDC
Software console.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
[ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
[ARM] 4001/1: S3C24XX: shorten reboot time
[ARM] 3983/2: remove unused argument to __bug()
[ARM] 4000/1: Osiris: add third serial port in
[ARM] 3999/1: RX3715: suspend to RAM support
[ARM] 3998/1: VR1000: LED platform devices
[ARM] 3995/1: iop13xx: add iop13xx support
[ARM] 3968/1: iop13xx: add iop13xx_defconfig
[ARM] Update mach-types
[ARM] Allow gcc to optimise arm_add_memory a little more
[ARM] 3991/1: i.MX/MX1 high resolution time source
[ARM] 3990/1: i.MX/MX1 more precise PLL decode
[ARM] 3986/1: H1940: suspend to RAM support
[ARM] 3985/1: ixp4xx clocksource cleanup
[ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
[ARM] 3994/1: ixp23xx: fix handling of pci master aborts
[ARM] 3981/1: sched_clock for PXA2xx
[ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
[ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
[ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
...
The pl010 primecell documentation specifies that an error indicated via RSR
should be cleared by a write to ECR. We didn't do this, which was causing
errors to be re-reported on every call to pl010_rx_chars().
Doing a write to ECR once we detect an error appears to prevent the ep93xx
console UART driver from going into a mode where it reports "ttyAM0: X
input overrun(s)" every couple of keystrokes.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add suspend/resume methods to drivers/serial/8250_pnp.c. Tested on a
P4/HT 16550A box, ttyS0 login survives across suspend to ram.
[akpm@osdl.org: cleanups]
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This a set of fixes mostly to make the driver actually work:
1. Actually select the line for setting parameters and receiver
disable/enable.
2. Select the line for receive and transmit interrupt handling correctly.
3. Report the transmitter empty state correctly.
4. Set the I/O type of ports correctly.
5. Perform polled transmission correctly.
6. Don't fix the console line at ttyS3.
7. Magic SysRq support.
8. Various small bits here and there.
Tested with a DECstation 2100 (thanks Flo for making this possible).
[akpm@osdl.org: fix typo]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass struct dev pointer to dma_cache_sync()
dma_cache_sync() is ill-designed in that it does not have a struct device
pointer argument which makes proper support for systems that consist of a
mix of coherent and non-coherent DMA devices hard. Change dma_cache_sync
to take a struct device pointer as first argument and fix all its callers
to pass it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is on our "Envoy" boxes which we have, according to the documentation, an
"Exar ST16C554/554D Quad UART with 16-byte Fifo's". The box also has two
other "on-board" serial ports and a modem chip.
The two on-board serial UARTs were being detected along with the first two
Exar UARTs. The last two Exar UARTs were not showing up and neither was the
modem.
This patch was the only way I could the kernel to see beyond the standard four
serial ports and get all four of the Exar UARTs to show up.
[akpm@osdl.org: build fix]
Signed-off-by: Paul B Schroeder <pschroeder@uplogix.com>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a driver for the Xilinx uartlite serial controller used in boards with
the PPC405 core in the Xilinx V2P/V4 fpgas.
The hardware is very simple (baudrate/start/stopbits fixed and no break
support). See the datasheet for details:
http://www.xilinx.com/bvdocs/ipcenter/data_sheet/opb_uartlite.pdf
See http://thread.gmane.org/gmane.linux.serial/1237/ for the email thread.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (43 commits)
sh: sh775x/titan fixes for irq header changes.
sh: update r7780rp defconfig.
sh: compile fixes for header cleanup.
sh: Fixup pte_mkhuge() build failure.
sh: set KBUILD_IMAGE to something sensible.
sh: show held locks in stack trace with lockdep.
sh: platform_pata support for R7780RP
sh: stacktrace/lockdep/irqflags tracing support.
sh: Fixup movli.l/movco.l atomic ops for gcc4.
sh: dyntick infrastructure.
sh: Clock framework tidying.
sh: Turn off IRQs around get_timer_offset() calls.
sh: Get the PGD right in oops case with 64-bit PTEs.
sh: Fix store queue bitmap end.
sh: More flexible + SH7780 earlyprintk SCIF support.
sh: Fixup various PAGE_SIZE == 4096 assumptions.
sh: Fixup 4K irq stacks.
sh: dma-api channel capability extensions.
sh: Drop name overload in dma-sh.
sh: Make dma-isa depend on ISA_DMA_API.
...
Some updates for the old ColdFire serial driver:
. support 3 and 4 UARTs on some ColdFire parts that have them
. enable multifunction pins to serial for 527x CPU's
. support the 5272 UART's fractional baud rate divisor
. switch driver name to "mcfserial"
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes the early printk support somewhat more flexible,
moving the port definition to a config option, and making the
port initialization configurable for sh-ipl+g users.
At the same time, this allows us to trivially wire up the
SH7780 SCIF0, so that's thrown in too more or less for free.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH7206 (SH-2A) and SH7619
(SH-2) MMU-less CPUs.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
struct pcmcia_device *p_dev->conf.ConfigBase and .Present are set in almost
all PCMICA driver right at the beginning, using the same calls but slightly
different implementations. Unfiy this in the PCMCIA core.
Includes a small bugfix ("drivers/net/pcmcia/xirc2ps_cs.c: remove unused
label") from and Signed-off-by Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we read out the manufactor and card_id from the PCMCIA device in the
PCMCIA core, and device drivers can access those reliably in struct
pcmcia_device's fields manf_id and card_id, remove additional (and partly
broken) manf_id and card_id detection logic from PCMCIA device drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add IDs for Elan serial PCMCIA devices. In addition, move the
pdaudio_cf driver from matching based on manf_id and card_id to
the more specific prod_id1 and prod_id2 to avoid false
positives.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Needed to support mpc52xx boards in arch/powerpc. This patch
retains the platform_bus support when compiling for arch/ppc,
but uses the of_platform bindings for arch/powerpc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Single typo fix and whitespace changes. In preparation for heavy
changes to this driver when support for arch/powerpc is added.
Since the driver will be changing significantly anyway, then may
as well take the opportunity to clean it up first.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated some of the comments in the atmel_serial.h header detailing
which bits are only available on the AT91RM9200 or the AT91SAM9xx
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. The CPU identification has moved from <system.h> to <cpu.h>.
2. AT91RM9200_BASE_US0 is only defined if we are compiling in support
for the AT91RM9200. Therefore we need to replace the CONFIG_ARM ifdef
with CONFIG_ARCH_AT91RM9200
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The below hunk was missed from the recent patch, and now, there are somewhat
inconsistent definitions:
in cpm_uart.h:
int __init cpm_uart_init_portdesc(void);
in cpm_uart_cpm1.c:
int __init cpm_uart_init_portdesc(void)
{
}
in cpm_uart_cpm2.c:
int cpm_uart_init_portdesc(void)
{
}
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates the drivers (and other files) which include the
hardware headers. This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).
The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h. Renamed it to at91_pdc.h
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch replaces the arch_identify() in system.h with a set of
cpu_is_XXX() macro's. This allows for compile-time checking of the
target AT91 processor.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The cpm_uart driver is initialised incorrectly, if there is a frame buffer
console, and CONFIG_SERIAL_CPM_CONSOLE is defined. The driver fails to
call cpm_uart_init_portdesc() and set_lineif() in this case.
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SMC and SCC hardware transmitter is enabled at the wrong
place. Simply writing twice to the non-console port, like
$ echo asdf > /dev/ttyCPM1
$ echo asdf > /dev/ttyCPM1
puts the shell into endless uninterruptible sleep, since the
transmitter is stopped after the first write, and is not enabled
before the shutdown function of the second write. Thus the transmit
buffers are never emptied.
Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix typo (repeated) in serial Kconfig.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SGI PCI-RT card, based on the SGI IOC4 chip, will be made available on
Altix XE (x86_64) platforms in the near future. As such it is now a
misnomer for the IOC4 base device driver to live under drivers/sn, and
would complicate builds for non-SN2.
This patch moves the IOC4 base driver code from drivers/sn to drivers/misc,
and updates the associated Makefiles and Kconfig files to allow building on
non-SN2 configs. Due to the resulting change in link order, it is now
necessary to use late_initcall() for IOC4 subdriver initialization.
[akpm@osdl.org: __udivdi3 fix]
[akpm@osdl.org: fix default in Kconfig]
Acked-by: Pat Gefre <pfg@sgi.com>
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix this 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:sunzilog_console_setup from .data between 'sunzilog_console' (at offset 0x8394) and 'devices_subsys'
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Eliminate casts to/from void*
- Eliminate checks for conditions that never occur. These typically
fall into two classes:
1) Checking for 'dev_id == NULL', then it is never called with
NULL as an argument.
2) Checking for invalid irq number, when the only caller (the
system) guarantees the irq handler is called with the proper
'irq' number argument.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
The atmel_console_get_options() function initializes the baud,
parity and bits settings from the actual hardware setup, in
case it has been initialized by a e.g. boot loader.
The baud rate, however, is not necessarily exactly equal to one of
the standard baud rates (115200, etc.) This means that the baud rate
calculated by this function may be slightly higher or slightly lower
than one of the standard baud rates.
If the baud rate is slightly lower than the target, this causes
problems when uart_set_option() tries to match the detected baud rate
against the standard baud rate, as it will always select a baud rate
that is lower or equal to the target rate. For example if the
detected baud rate is slightly lower than 115200, usart_set_options()
will select 57600.
This patch fixes the problem by subtracting 1 from the value in BRGR
when calculating the baud rate. The detected baud rate will thus
always be higher than the nearest standard baud rate, and
uart_set_options() will end up doing the right thing.
Tested on ATSTK1000 and AT91RM9200-EK boards. Both are broken without
this patch.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make CONFIG_SERIAL_ATMEL selectable on AVR32 and #ifdef out some ARM-
specific code in the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.
This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.
On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.
If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename at91_register_uart_fns and associated structs and variables
to make it consistent with the atmel_ prefix used by the rest of
the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The at91_serial driver can be used with both AT32 and AT91 devices
from Atmel and has therefore been renamed atmel_serial. The only
thing left is to rename PORT_AT91 PORT_ATMEL.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prefix all internal functions and variables with atmel_ instead of
at91_.
The at91_register_uart_fns() stuff is left as is since I can't find
any actual users of it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move include/asm/arch/at91rm9200_usart.h into drivers/serial and rename
it atmel_usart.h. Also delete AVR32's version of this file.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh:
Remove all inclusions of <linux/config.h>
Manually resolved trivial path conflicts due to removed files in
the sound/oss/ subdirectory.
Russell King pointed out that asm/serial.h is anachronistic and we were
misusing BASE_BAUD. So fix BASE_BAUD for PCI 16550 UARTs, move LASI_BASE_BAUD
into 8250_gsc, and fix the obsolete comment about reserving serial port slots.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (29 commits)
[POWERPC] Fix rheap alignment problem
[POWERPC] Use check_legacy_ioport() for ISAPnP
[POWERPC] Avoid NULL pointer in gpio1_interrupt
[POWERPC] Enable generic rtc hook for the MPC8349 mITX
[POWERPC] Add powerpc get/set_rtc_time interface to new generic rtc class
[POWERPC] Create a "wrapper" script and use it in arch/powerpc/boot
[POWERPC] fix spin lock nesting in hvc_iseries
[POWERPC] EEH failure to mark pci slot as frozen.
[POWERPC] update powerpc defconfig files after libata kconfig breakage
[POWERPC] enable sysrq in pmac32_defconfig
[POWERPC] UPIO_TSI cleanup
[POWERPC] rewrite mkprep and mkbugboot in sane C
[POWERPC] maple/pci iomem annotations
[POWERPC] powerpc oprofile __user annotations
[POWERPC] cell spufs iomem annotations
[POWERPC] NULL noise removal: spufs
[POWERPC] ppc math-emu needs -fno-builtin-fabs for math.c and fabs.c
[POWERPC] update mpc8349_itx_defconfig and remove some debug settings
[POWERPC] Always call cede in pseries dedicated idle loop
[POWERPC] Fix loop logic in irq_alloc_virt()
...
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking. One of these
structures was a struct tty_operations. In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.
This patch declares all struct tty_operations in the tree as const. In all
cases, they are static and used only as input to tty_set_operations. As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.
53 drivers are affected. I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months. serial_core.c was the busiest one that I looked at.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Compaq TC1000 and Fujitsu Stylistic range of tablet machines use
touchscreens from FPI. These are implemented as serial interfaces,
generally exposed in the ACPIPNP information on the system. This patch
adds them to the 8250_pnp driver tables, avoiding the need to mess
around with setserial to set them up.
I haven't been able to confirm what FUJ02B5, FUJ02BA and FUJ02BB are.
FUJ02B1 refers to the controller for the system hotkeys. FUJ02BC appears
to be the last in the range - after this, they moved to Wacom-based
systems.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Serial is _slow_ sometimes. So slow, that the NMI watchdog kicks in.
NMI Watchdog detected LOCKUP on CPU2CPU 2
Modules linked in: loop usb_storage md5 ipv6 parport_pc lp parport autofs4 i2c_dev i2c_core rfcomm l2cap bluetooth sunrpc pcdPid: 3138, comm: gpm Not tainted 2.6.11-1.1290_FC4smp
RIP: 0010:[<ffffffff80273b8a>] <ffffffff80273b8a>{serial_in+106}
RSP: 0018:ffff81003afc3d50 EFLAGS: 00000002
RAX: 0000000000000020 RBX: 0000000000000020 RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff804dcd60
RBP: 00000000000024fc R08: 000000000000000a R09: 0000000000000033
R10: ffff81001beb7c20 R11: 0000000000000020 R12: ffffffff804dcd60
R13: ffffffff804ade76 R14: 000000000000002b R15: 000000000000002c
FS: 00002aaaaaac4920(0000) GS:ffffffff804fca00(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00002aaaaabcb000 CR3: 000000003c0d0000 CR4: 00000000000006e0
Process gpm (pid: 3138, threadinfo ffff81003afc2000, task ffff81003eb63780)
Stack: ffffffff80275f2e 0000000000000000 ffffffff80448380 0000000000007d6b
000000000000002c fffffffffffffbbf 0000000000000292 0000000000008000
ffffffff80138e8c 0000000000007d97
Call Trace:<ffffffff80275f2e>{serial8250_console_write+270} <ffffffff80138e8c>{__call_console_drivers+76}
<ffffffff8013914b>{release_console_sem+315} <ffffffff80260325>{con_open+149}
<ffffffff80254e99>{tty_open+537} <ffffffff80192713>{chrdev_open+387}
<ffffffff80188824>{dentry_open+260} <ffffffff80188994>{filp_open+68}
<ffffffff80187b73>{get_unused_fd+227} <ffffffff80188a6c>{sys_open+76}
<ffffffff8010ebc6>{tracesys+209}
Code: 0f b6 c0 c3 66 90 41 57 49 89 f7 41 56 41 be 00 01 00 00 41
console shuts up ...
I initially did the patch below a year ago for the Fedora kernel, and have
been keeping it up to date since. I recently got the same thing happening
on a vanilla kernel, so figured it was time to repost this.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A serial card might have been removed when the system is resumed.
This results in a suspended port being shut down, which results in
the ports shutdown method being called twice in a row. This causes
BUGs. Avoid this by tracking the suspended state separately from
the initialised state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, pcmcia_dev_present() returns false when a device is
suspended, so checking this on resume does not work too well. Omit
this test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove some code which is unneeded if CONFIG_PM=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch below is necessary for 115200 baud on an OMAP1510 internal UART.
It's been in the linux-omap tree for some time and with it applied to a
vanilla Linus git tree the serial console on the Amstrad Delta (which is
OMAP1510 based and whose initial bootloader runs at 115200) works fine (it
doesn't without it).
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the issue of returning 0 even in case of error from uart_set_info
function. Now it returns the error EBUSY when it can not set new port.
Signed-off-by: Ram Gupta <r.gupta@astronautics.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/proc/tty/driver/serial incorrectly claims that UARTs having iotype of
UPIO_MEM32, UPIO_AU, or UPIO_TSI are I/O mapped.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
8250.c and serial_txx9.c port suspend/resume handler still have this obsolete
argument documented...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I think register ranges obviously need to be claimed/released for all UARTs
including those with UPIO_MEM32 and UPIO_TSI iotype.
Also, serial8250_request_rsa_resources() returns false positives with
UPIO_MEM32, UPIO_AU, and UPIO_TSI iotype -- I don't think this makes any sense.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mauro Ziliani reports that this card has a higher clock rate.
Rather than tweak the 8250 driver to handle this, add a quirk to
pass the correct clock rate to the driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the existing code, Nokia only make single-port cards,
but are detected as multi-port cards. Handle this in roughly the
same way via the config quirk - forcing it to be a real single port
card (info->multi=0) changes the way we allocate the IO memory,
which might stop the card working.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a quirk primerily to handle tweaks to the link->conf structure,
eg as required for Socket cards.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move IBM quirk handling into its own quirk entry. Note that doing
quirk handling after we've registered the ports is racy, but since
I don't know if moving this will have an undesired effect, it's
probably better to leave where it is.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some quirks we will introduce next apply to (eg) all cards of one
manufacturer. Therefore, we need a way to list these in the quirk
table - use ~0 - this is not a possible device ID value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- rename multi_id table to serial_quirk / quirks[]
- use named initialisers
- store a pointer to the quirk table in the serial_info structure
so we can use the quirk table entry later.
- apply multi-port quirk after the multi-port guessing code,
but only if it's != -1.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Use ARRAY_SIZE() instead of home grown based version.
- use parse->manfid.card rather than le16_to_cpu(buf[1]) -
manfid.card is already converted to this format.
- use info->prodid in subsequent tests rather than
parse->manfid.card.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
m32r_sio re-uses a custom defined BASE_BAUD from asm/serial.h,
and replaces SERIAL_PORT_DFNS with its own driver private copy.
Since asm/serial.h is supposed to define 8250-based ports using
these symbols, this isn't a sane idea.
Hence, eliminate asm/serial.h from m32r_sio.c.
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David S. Miller <davem@sunset.davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the Kconfig entry for console on AMBA PL011 to match the code.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sh-sci needs to be able to define its number of ports to
support, we do this with a config option, like most other
ports do.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh-sci was turning in to an unmaintainable mess, especially with
regards to the port list. This cleans it up quite a bit, and
switches over to a platform device model where subtypes will
register their port list individually in their setup code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Hack uart_suspend_port() and uart_resume_port() so that serial console
ports are not suspended if CONFIG_DISABLE_CONSOLE_SUSPEND is set.
This makes it possible to debug the suspend and resume routines of all
device drivers as well as the lowest-level swsusp code with the help of the
serial console.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(le32_to_cpu(x) >> 8) & 0xff is a very odd way to spell (x >> 16) & 0xff,
even if that code is hit only on ppc. The value is host-endian - we've
got it from readl(), after all...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The fs_no mean used to be fs_enet driver driven, hence it was an
enumeration across all the possible fs_enet "users" in the SoC. Now, with
QE on the pipeline, and to make DTS descriptions more clear, fs_no features
relevant SoC part number, with additional field to describe the SoC type.
Another reason for that is now not only fs_enet is going to utilize those
stuff. There might be UART, HLDC, and even USB, so to prevent confusion and
be ready for upcoming OF_device transfer, fs_enet and cpm_uart drivers were
updated in that concern, as well as the relevant DTS.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Incorporating the new way of cpm2 immr access, introduced in the previous
patch, into CPM2 peripheral devices (fs_enet and cpm_uart). Both ppc and
powerpc approved working( real actions taken in powerpc only, ppc just
has a wrapper to keep init stuff consistent).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
The stuff below cleans up the code attempting to remap the whole cpm2_immr
early, as well as places happily assuming that fact. This is more like the 2.4
legacy stuff, and is at least confusing and unclear now.
To keep the world comfortable, a new mechanism is introduced: before accessing
specific immr register/register set, one needs to map it, using cpm2_map(<reg>),
for instance, access to CPM command register will look like
volatile cpm_cpm2_t *cp = cpm2_map(im_cpm);
keeping the code clear, yet without "already defined somewhere" cpm2_immr.
So far, unmapping code is not implemented, but it's not a big deal to add it,
if the whole idea makes sense.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Driver core has been updated to make use of the new powerpc OF-inspired
platform devices, yet keeping compatibility to the vast board list from
ppc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Patch from Ben Dooks
The S3C2440 serial info struct is being passed
through the S3C2412 serial info struct probe
routine.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Glexiner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While we've been sorting out the toolchain fiasco, some of
the code has suffered a bit of bitrot. Building with GCC4
also brings up some more build warnings. Trivial fixes for
both issues.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- some const- ification and usage of ARRAY_SIZE() in serial drivers
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
uart_match_port() always fails with UPIO_MEM32, UPIO_AU, and UPIO_TSI cases.
Since they match to the memory mapped UARTs, they should be handled just like
UPIO_MEM case.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here is a patch that adds support for the Instashield IS-200 2 port PCI
serial card.
Signed-off-by: Peter Horton <pdh@colonel-panic.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes yet another sunsab problem, when console is set to anything
but the first port. The console framework calls sunsab_console_setup
for each port, and we end up setting up a console on a not yet
discovered port, which leads to an Oops. Instead, defer console setup
until the requested port is properly initialized. Tested on an E250
through an RSC console.
Reported by Daniel Smolik <marvin@mydatex.cz>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
powermac platform & macintosh driver changes.
Built for pmac32_defconfig, g5_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just do a linear enumeration so that we handle sun4d systems
correctly. As a consequence, eliminate the hard coded keyboard and
mouse channel line values, use the CONS_{KEYB,MS} flags instead.
Also, report the keyboard/mouse Zilog channels just like the uart ones
do.
Signed-off-by: David S. Miller <davem@davemloft.net>
Table sizing code should look for "se" not "su" nodes.
The chip at the lower address should get the first index.
Signed-off-by: David S. Miller <davem@davemloft.net>
Register second SAB port before the first one, as serial A is wired to
it, and expected to appear as ttyS0.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of initializing both ports of a SAB device
properly, we were setting up the first port
structure twice and ending up only with the second
port, oops.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (53 commits)
[MIPS] sparsemem: fix crash in show_mem
[MIPS] vr41xx: Update workpad setup function
[MIPS] vr41xx: Update e55 setup function
[MIPS] vr41xx: Removed old v2.4 VRC4173 driver
[MIPS] vr41xx: Move IRQ numbers to asm-mips/vr41xx/irq.h
[MIPS] MIPSsim: Build fix, rename sim_timer_setup -> plat_timer_setup.
[MIPS] Remove unused code.
[MIPS] IP22 Fix brown paper bag in RTC code.
[MIPS] Atlas, Malta, SEAD: Don't disable interrupts in mips_time_init().
[MIPS] Replace board_timer_setup function pointer by plat_timer_setup.
[MIPS] Nuke redeclarations of board_time_init.
[MIPS] Remove redeclarations of setup_irq().
[MIPS] Nuke redeclarations of board_timer_setup.
[MIPS] Print out TLB handler assembly for debugging.
[MIPS] SMTC: Reformat to Linux style.
[MIPS] MIPSsim: Delete redeclaration of ll_local_timer_interrupt.
[MIPS] IP27: Reformatting.
[MIPS] IP27: Invoke setup_irq for timer interrupt so proc stats will be shown.
[MIPS] IP27: irq_chip startup method returns unsigned int.
[MIPS] IP27: struct irq_desc member handler was renamed to chip.
...
The sunsu_ports[] array exists merely to be able to easily
use an integer index to get at the proper serial console
port struct.
We size this only for real ports, not for the keyboard and
mouse, and thus keyboard and mouse port registration would
fail.
Fix this by dynamically allocating the port struct for the
keyboard and mouse, instead of using the sunsu_ports[]
array.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=6716
Doing a sysrq over a serial line into an SMP machine presently deadlocks.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The following patch gets rid of CONFIG_TSI108_BRIDGE. I add UPIO_TSI to
handle IIR and IER register in serial_in and serial_out.
(1) the reason to rewrite serial_in:
TSI108 rev Z1 version ERRATA. Reading the UART's Interrupt
Identification Register (IIR) clears the Transmit Holding Register
Empty (THRE) and Transmit buffer Empty (TEMP) interrupts even if they
are not enabled in the Interrupt Enable Register (IER). This leads to
loss of the interrupts. Interrupts are not cleared when reading UART
registers as 32-bit word.
(2) the reason to rewrite serial_out:
Check for UART_IER_UUE bit in the autoconfig routine. This section
of autoconfig is excluded for Tsi108/109 because bits 7 and 6 are
reserved for internal use. They are R/W bits. In addition to
incorrect identification, changing these bits (from 00) will make
Tsi108/109 UART non-functional.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch below fixes serial console hangs as seen on IP22
machines. Typically, while booting, the machine hangs for ~1 minute
displaying "INIT: ", then the same thing happens again when init
enters in the designated runlevel and finally the getty process on
ttyS0 hangs indefinitely (though strace'ing it helps).
strace (-e raw=ioctl, otherwise the ioctl() translation is utterly
bogus) reveals that getty hangs on ioctl() 0x540f which happens to be
TCSETSW (I saw it hang on another console ioctl() but couldn't
reproduce that one).
A diff between ip22zilog and sunzilog revealed the following
differences:
1. the channel A flag being set on up.port.flags instead of up.flags
2. the channel A flag being set on what is marked as being channel B
3. sunzilog has a call to uart_update_timeout(port, termios->c_cflag, baud);
at the end of sunzilog_set_termios(), which ip22zilog lacks (on
purpose ?)
The patch below addresses point 1 and fixes the serial console hangs
just fine. However point 2 should be investigated by someone familiar
with the IP22 Zilog; it's probably OK as is but even if it is, a
comment in ip22zilog.c is badly needed.
Point 3 is left as an exercise for whoever feels like digging into
ip22zilog :)
These are the main obvious differences between ip22zilog and
sunzilog. Newer versions of sunzilog (Linus's git tree as of today)
are more close to ip22zilog as the sbus_{write,read}b have been
changed into simple {write,read}b, which shrinks the diff by a fair
amount. Resyncing both drivers should be doable in a few hours time
now for someone familiar with the IP22 Zilog hardware.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the following compilation error in the dz serial driver that got
introduced with the "kernel console should send CRLF not LFCR" change.
CC drivers/serial/dz.o
drivers/serial/dz.c: In function 'dz_console_putchar':
drivers/serial/dz.c:679: error: 'uport' undeclared (first use in this function)
drivers/serial/dz.c:679: error: (Each undeclared identifier is reported only once
drivers/serial/dz.c:679: error: for each function it appears in.)
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
The AT91RM9200 errata work-around should be using the GPIO API and not
accessing the PIO registers directly.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Ensure 8250_pci quirks are not marked __devinit
[SERIAL] Convert fifosize to an unsigned int
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: add defconfig for Freescale MPC8349E-mITX board
powerpc: Add base support for the Freescale MPC8349E-mITX eval board
Documentation: correct values in MPC8548E SEC example node
[POWERPC] Actually copy over i8259.c to arch/ppc/syslib this time
[POWERPC] Add new interrupt mapping core and change platforms to use it
[POWERPC] Copy i8259 code back to arch/ppc
[POWERPC] New device-tree interrupt parsing code
[POWERPC] Use the genirq framework
[PATCH] genirq: Allow fasteoi handler to retrigger disabled interrupts
[POWERPC] Update the SWIM3 (powermac) floppy driver
[POWERPC] Fix error handling in detecting legacy serial ports
[POWERPC] Fix booting on Momentum "Apache" board (a Maple derivative)
[POWERPC] Fix various offb and BootX-related issues
[POWERPC] Add a default config for 32-bit CHRP machines
[POWERPC] fix implicit declaration on cell.
[POWERPC] change get_property to return void *
Teach special (dual-initialized) locking code to the lock validator. Has no
effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PNP devices can use shared interrupts, so check to see whether we'll need
SA_SHIRQ for request_irq().
The builtin PDH UART on the HP rx8640 is an example of an ACPI/PNP device
that uses a shareable level-triggered, active-low interrupt. The interrupt
can be shared in very large I/O configurations or by artificially lowering
IA64_DEF_LAST_DEVICE_VECTOR.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Li Shaohua <shaohua.li@intel.com>
Cc: Len Brown <len.brown@intel.com>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 8250_pci quirks must not be marked __devinit since they may
be used from parport_serial. We only really need to mark those
which might be used by cards recognised by parport_serial, but
that wouldn't allow static checking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the new irq remapper core and removes the old one. Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).
This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.
For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259. That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.
The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some UARTs have more than 255 bytes of FIFO, which can't be
represented by an unsigned char. Change the kernel's internal
structure to be an unsigned int, but still export an unsigned char
via the TIOCGSERIAL ioctl. If the TIOCSSERIAL ioctl provides a
fifo size of 0, assume this means "don't change" otherwise we'll
corrupt the larger fifo sizes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Kill sun4v virtual device layer.
[SERIAL] sunhv: Convert to of_driver layer.
[SPARC64]: Mask out top 8-bits in physical address when building resources.
[SERIAL] sunsu: Missing return statement in su_probe().
1) Need to unregister 2 ports per of_device.
2) Need to of_iounmap() 1 mapping per of_device.
3) Need to free up the IRQ only after all devices
have been unregistered.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
Remove TTY_DONT_FLIP tty flag. This flag was introduced in 2.1.X kernels
to prevent the N_TTY line discipline functions read_chan() and
n_tty_receive_buf() from running at the same time. 2.2.15 introduced
tty->read_lock to protect access to the N_TTY read buffer, which is the
only state requiring protection between these two functions.
The current TTY_DONT_FLIP implementation is broken for SMP, and is not
universally honored by drivers that send data directly to the line
discipline receive_buf function.
Because TTY_DONT_FLIP is not necessary, is broken in implementation, and is
not universally honored, it is removed.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've always found this flag confusing. Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.
Also fixes all drivers that use this flag.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ColdFire serial driver support for the new 532x CPU family UARTs.
Patch submitted by Matt Waddel <Matt.Waddel@freescale.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (25 commits)
[ARM] 3648/1: Update struct ucontext layout for coprocessor registers
[ARM] Add identifying number for non-rt sigframe
[ARM] Gather common sigframe saving code into setup_sigframe()
[ARM] Gather common sigframe restoration code into restore_sigframe()
[ARM] Re-use sigframe within rt_sigframe
[ARM] Merge sigcontext and sigmask members of sigframe
[ARM] Replace extramask with a full copy of the sigmask
[ARM] Remove rt_sigframe puc and pinfo pointers
[ARM] 3647/1: S3C24XX: add Osiris to the list of simtec pm machines
[ARM] 3645/1: S3C2412: irq support for external interrupts
[ARM] 3643/1: S3C2410: Add new usb clocks
[ARM] 3642/1: S3C24XX: Add machine SMDK2413
[ARM] 3641/1: S3C2412: Fixup gpio register naming
[ARM] 3640/1: S3C2412: Use S3C24XX_DCLKCON instead of S3C2410_DCLKCON
[ARM] 3639/1: S3C2412: serial port support
[ARM] 3638/1: S3C2412: core clocks
[ARM] 3637/1: S3C24XX: Add mpll clock, and set as fclk parent
[ARM] 3636/1: S3C2412: Add selection of CPU_ARM926
[ARM] 3635/1: S3C24XX: Add S3C2412 core cpu support
[ARM] 3633/1: S3C24XX: s3c2410 gpio bugfix - wrong pin nos
...
Patch from Ben Dooks
Serial port support for the on-board UART blocks
on the Samsung S3C2412 and S3C2413 UARTs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are three different IO cards which an SGI IOC4 controller may find
itself on. One of these variants does not bring out the IDE and serial
signals, so we need to disable attaching the corresponding IOC4 subdrivers
to such cards.
Cleans up message clutter emitted during device probing.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (21 commits)
[ARM] 3629/1: S3C24XX: fix missing bracket in regs-dsc.h
[ARM] 3537/1: Rework DMA-bounce locking for finer granularity
[ARM] 3601/1: i.MX/MX1 DMA error handling for signaled channels only
[ARM] 3597/1: ixp4xx/nslu2: Board support for new LED subsystem
[ARM] 3595/1: ixp4xx/nas100d: Board support for new LED subsystem
[ARM] 3626/1: ARM EABI: fix syscall restarting
[ARM] 3628/1: S3C24XX: add get_rate call to struct clk
[ARM] 3627/1: S3C24XX: split s3c2410 clocks from core clocks
[ARM] 3613/1: S3C2410: Add sysdev and sysclass
[ARM] 3624/1: Report true modem control line states
[ARM] 3620/2: ixp23xx: add uengine loader support
[ARM] 3618/1: add defconfig for logicpd pxa270 card engine
[ARM] 3617/1: ep93xx: fix slightly incorrect timer tick rate
[ARM] 3616/1: fix timer handler wrap logic for a number of platforms
[ARM] 3615/1: ixp23xx: use platform devices for physmap flash
[ARM] 3614/1: ep93xx: use platform devices for physmap flash
[ARM] 3621/1: fix compilation breakage for pnx4008
[ARM] 3623/1: pnx4008: move GPIO-related defines to gpio.h
[ARM] 3622/1: pnx4008: remove clk_use/clk_unuse
[ARM] Enable VFP to be built when non-VFP capable CPUs are selected
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
[ARM] 3600/1: increase amba-pl010 UART_NR to 8
[ARM] 3571/1: netX: serial driver for Hilscher netX
Patch from Uli Luckas
This patch removes the fake return from serial_pxa_get_mctrl.
Signed-off-by: Uli Luckas <u.luckas@road-gmbh.de>
I just can't remember why this return was there.
Being in the first column clearly indicates it was meant to be removed.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The cirrus ep93xx has 3 pl010 UARTs, while amba-pl010.c only allows
for 2 by default. A while ago, I think we agreed on changing the 2
to 8, but I don't see this in 2.6.17 yet.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Andrew Victor
This patch includes a number of updates to the AT91RM9200 serial driver.
Changes include:
1. Conversion to a platform_driver. [Ivan Kokshaysky]
2. Replaced all references to AT91RM9200 with AT91. This driver can now
also be used for the AT91SAM9216.
3. Allow TIOCM_LOOP to configure local loopback mode.
4. Cleaned up the 'read_status_mask' usage and interrupt handler code.
[Chip Coldwell]
5. Suspend/resume support. [David Brownell]
There are a few 'unused variable' warning when compiling this - I
removed the new DMA support to keep this first patch simpler.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds the serial driver for Hilscher's netX network
processors.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Core support for the Samsung S3C2442, and the
serial port driver update to allow the serial
port blocks to be used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
The serial driver now sets up the third UART when it is to be used.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes various odd things that missed update together with cpm_uart
platform_device move. Unified resources names, restructurisation, etc.
Also, addressed issue with recent phys/virt translation rework. Being
cache-coherent, CPM2's do alloc_bootmem() for the console stuff, and it was
used to treat console buffer descriptor mapping 1:1 (as in CPM1 case),
which is definitely wrong.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
FATAL: modpost: GPL-incompatible module sunsu uses the GPL-only symbol tty_insert_flip_string_flags
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Andrew Victor
The serial_core already manages the power state of the UARTs, and
therefore it shouldn't suspend a UART which was previously suspended.
This patch modifies serial_core only call the UART-specific
power-management function if the PM state is actually changing.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] 8250: add locking to console write function
[SERIAL] Remove unconditional enable of TX irq for console
[SERIAL] 8250: set divisor register correctly for AMD Alchemy SoC uart
[SERIAL] AMD Alchemy UART: claim memory range
[SERIAL] Clean up serial locking when obtaining a reference to a port
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: Use the ibm,pa-features property if available
powerpc: Fix incorrect might_sleep in __get_user/__put_user on kernel addresses
[PATCH] ppc32 CPM_UART: fixes and improvements
[PATCH] ppc32 CPM_UART: Fixed break send on SCC
[PATCH] powerpc/kprobes: fix singlestep out-of-line
[PATCH] powerpc/pseries: avoid crash in PCI code if mem system not up
Patch from Sascha Hauer
This patch moves the i.MX uart resources and the gpio pin setup to the
board files. This allows the boards to decide how many internal uarts
are connected to the outside world and whether they use rts/cts or
not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A number of small issues are fixed, and added the header file, missed from the
original series. With this, driver should be pretty stable as tested among
both platform-device-driven and "old way" boards. Also added missing GPL
statement , and updated year field on existing ones to reflect
code update.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SCC uart sends a break sequence each time it is stopped with the
CPM_CR_STOP_TX command. That means that each time an application closes the
serial device, a break is transmitted. To fix this, graceful tx stop is
issued for SCC.
Signed-off-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
x86 SMP breaks as a result of the previous change, we have no real
option other than to add locking to the 8250 console write function.
If an oops is in progress, try to acquire the lock. If we fail to
do so, continue anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A bug report from Gerd Hoffmann has highlighted that unconditionally
enabling the transmit interrupt at the end of console writes is very
bad.
In Gerd's case, it causes the test for buggy UARTs to give false
positives, incorrectly identifying ports as buggy when they are not.
Moreover, if we unconditionally enable the interrupt, and the port
is sharing it's interrupt with other ports, there is the very real
possibility that we'll cause an interrupt storm. (Not all ports use
OUT2 as an interrupt mask.)
Hence, revert part of f91a3715db and
all of f5968b37b3 until a better solution
can be found.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Alchemy SoC uart have got a non-standard divisor register that needs some
special handling.
This patch adds divisor read/write functions with test and special
handling for Alchemy internal uart.
Signed-off-by: Jon Anders Haugum <jonah@omegav.ntnu.no>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've noticed that the 8250/Au1x00 driver (drivers/serial/8250_au1x00.c)
doesn't claim UART memory ranges and uses wrong (KSEG1-based) UART
addresses instead of the physical ones.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The locking for the uart_port is over complicated, and can be
simplified if we introduce a flag to indicate that a port is "dead"
and will be removed.
This also helps the validator because it removes a case of non-nested
unlock ordering.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Current address translation methods can produce wrong results, because
virt_to_bus and vice versa may not produce correct offsets on dma-allocated
memory. The right way is, while tracking both phys and virt address of the
window that has been allocated for boffer descriptors, and use those
numbers to compute the offset and make translation properly.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is intended to make the driver code more generic and flexible,
to get rid of board-specific layouts within driver, and generic rehaul,
yet keeping compatibility with the existing stuff utilizing it, being
compatible with legacy behavior (but with complaints that legacy mode
used).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits)
Documentation: fix minor kernel-doc warnings
BUG_ON() Conversion in drivers/net/
BUG_ON() Conversion in drivers/s390/net/lcs.c
BUG_ON() Conversion in mm/slab.c
BUG_ON() Conversion in mm/highmem.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/ptrace.c
BUG_ON() Conversion in ipc/shm.c
BUG_ON() Conversion in fs/freevxfs/
BUG_ON() Conversion in fs/udf/
BUG_ON() Conversion in fs/sysv/
BUG_ON() Conversion in fs/inode.c
BUG_ON() Conversion in fs/fcntl.c
BUG_ON() Conversion in fs/dquot.c
BUG_ON() Conversion in md/raid10.c
BUG_ON() Conversion in md/raid6main.c
BUG_ON() Conversion in md/raid5.c
Fix minor documentation typo
BFP->BPF in Documentation/networking/tuntap.txt
...
Decrease the number of pointer derefs in drivers/serial/jsm/jsm_tty.c
Benefits of the patch:
- Fewer pointer dereferences should make the code slightly faster.
- Size of generated code is smaller
- Improved readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "V. ANANDA KRISHNAN" <mansarov@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This ugly hack add support for Siemens MC45 PCMCIA GPRS card (which is
identical to Possio GCC, and which is offered by one of our local GPRS
providers). Card has unfortunate feature that after poweron oxcf950 chip
is fully powered and works, but attached MC45 modem is powered down :-(
There is a special sequence (which takes 1 sec :-( ) to poweron MC45 (and
after MC45 powers on, it takes more than 2 secs until firmware fully
boots...) which needs to be executed after all powerons.
I'm really not familiar with PCMCIA subsystem, so I have no idea whether I
should issue request_region() on rest of oxcf950 address range (0-7 is
UART, 8-F are special configuration registers), or how this should be
better integrated with PM system and so on - I just put it in same place
where another hack already lived...
Card uses 18.432MHz XTAL, so to get it to work you must add lines below to
the /etc/pcmcia/serial.opts.
case "$MANFID-$FUNCID-$PRODID_1-$PRODID_2-$PRODID_3-$PRODID_4" in
'030c,0003-2-GPRS-CARD--')
SERIAL_OPTS="baud_base 1152000"
;;
esac
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Most of the driver initialization isn't done in the .probe function, but in
the internal _config() functions. Make them return a value, so that .probe
can properly report whether the probing of the device succeeded or not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In all but one case, the suspend and resume functions of PCMCIA drivers
contain mostly of calls to pcmcia_release_configuration() and
pcmcia_request_configuration(). Therefore, move this code out of the
drivers and into the core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_disable_device(struct pcmcia_device *p_dev) performs the necessary
cleanups upon device or driver removal: it calls the appropriate
pcmcia_release_* functions, and can replace (most) of the current drivers'
_release() functions.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Addresses in F-space must be accessed uncached on most parisc machines.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Allow the 8250 probe modules to be disabled if we're building for
with EMBEDDED enabled. This reduces the kernel size by not including
unnecessary probe module support.
Original idea from Matt Mackall for PCI only, expanded to others by
rmk.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Provide Cirrus EP93xx AMBA PL010 serial support.
[SERIAL] amba-pl010: allow platforms to specify modem control method
[SERIAL] Remove obsoleted au1x00_uart driver
[SERIAL] Small time UART configuration fix for AU1100 processor
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The amba-pl010 hardware does not provide RTS and DTR control lines; it
is expected that these will be implemented using GPIO. Allow platforms
to supply a function to implement manipulation of modem control lines.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As announced in feature-removal-schedule.txt.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AU1100 processor does not have an internal UART2. Only
UART0, UART1 and UART3 exist. This patch removes the non existing
UART2 and replaces it with a descriptive comment.
Signed-off-by: Freddy Spierenburg <freddy@dusktilldawn.nl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the combination of PNPACPI and 8250_pnp, we no longer need 8250_acpi.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The icom driver uses request_firmware()
and thus needs to select FW_LOADER.
Signed-off-by: maximilian attems <maks@sternwelten.at>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (21 commits)
BUG_ON() Conversion in drivers/video/
BUG_ON() Conversion in drivers/parisc/
BUG_ON() Conversion in drivers/block/
BUG_ON() Conversion in sound/sparc/cs4231.c
BUG_ON() Conversion in drivers/s390/block/dasd.c
BUG_ON() Conversion in lib/swiotlb.c
BUG_ON() Conversion in kernel/cpu.c
BUG_ON() Conversion in ipc/msg.c
BUG_ON() Conversion in block/elevator.c
BUG_ON() Conversion in fs/coda/
BUG_ON() Conversion in fs/binfmt_elf_fdpic.c
BUG_ON() Conversion in input/serio/hil_mlc.c
BUG_ON() Conversion in md/dm-hw-handler.c
BUG_ON() Conversion in md/bitmap.c
The comment describing how MS_ASYNC works in msync.c is confusing
rcu: undeclared variable used in documentation
fix typos "wich" -> "which"
typo patch for fs/ufs/super.c
Fix simple typos
tabify drivers/char/Makefile
...
Merge mpsc.h into mpsc.c because its the only file that #include's mpsc.h.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The definition of SUPPORT_SYSRQ must come before #include of serial_core.h.
This patch moves the definition of SUPPORT_SYSRQ to be just after the #include
of config.h to make it consistent with 8250.c.
Reported-by: Stephane Chazelas <Stephane@artesyncp.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The devname passed to request_irq() contained a '/' which is wrong. At
a minimum, the '/' prevented the devname from showing up in
/proc/irq/<irq>/<devname>. This patch replaces the '/' with a '-' to
fixes that problem.
Reported-by: Stephane Chazelas <Stephane@artesyncp.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add rs422 support to the Altix ioc4 serial driver.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
dio_module_init() used the device count to automatically unregister and
unload drivers that found no devices. That might have worked at one time,
but has been broken for some time because dio_register_driver() returned
either a negative error or a positive count (never zero). So it could only
unregister on failure, when it's not needed anyway.
This functionality could be resurrected in individual drivers by counting
devices in their .probe() methods.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Philip Blundell <philb@gnu.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes all occurances of _INLINE_ in the kernel.
With the exception of tty_flip.h, I've simply removed the inline's since
gcc should know best which functions to be inlined.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Merge avlab serial board entries in parport_serial
[SERIAL] kernel console should send CRLF not LFCR
The patch does the following for v441xx seris drivers:
- stop using platform_device_register_simple() as it is going away
- mark ->probe() and ->remove() methods as __devinit and __devexit
respectively
- initialize "owner" field in driver structure so there is a link
from /sys/modules to the driver
- mark *_init() and *_exit() functions as __init and __exit
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the serial_txx9 driver.
* More strict check in verify_port. Cleanup.
* Do not insert a char caused previous overrun.
* Fix some spin_locks.
* Do not call uart_add_one_port for absent ports.
Also, this patch removes a BROKEN tag from Kconfig. This driver has been
marked as BROKEN by removal of uart_register_port, but it has been solved
already on Sep 2005.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
platform_get_irq*() now returns on -ENXIO when the resource cannot be
found. Ensure all users of platform_get_irq*() handle this error
appropriately.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Glen Turner reported that writing LFCR rather than the more
traditional CRLF causes issues with some terminals.
Since this aflicts many serial drivers, extract the common code
to a library function (uart_console_write) and arrange for each
driver to supply a "putchar" function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Because we play this trick where we use ttyS? in increasing minor
numbers for different sunfoo.c drivers, we have to inform the TTY
layer of this.
Do so by setting the tty->name_base appropriately.
Probably there should be a generic way to do this in the serial core,
but for now...
Signed-off-by: David S. Miller <davem@davemloft.net>
Caller takes the lock already.
Also, fixup the poll loop in sunhv_break_ctl(). Just
like in console write, we udelay(2) and use a loop
limit of 1000000 iterations.
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it will show up as /dev/ttyS0. Otherwise things like
installers will try to run on whatever serial port gets probed
first.
Signed-off-by: David S. Miller <davem@davemloft.net>
By calling uart_handle_break(). We'll still do the
"sun_do_break()" handling if the user gives two
breaks in a row.
We should probably do this in the other Sparc serial
drivers too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Until the uart is openned, port->info is NULL.
Also, init the port->irq properly and give a non-zero
port->membase so that the uart device reporting is done.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add udelay to polling console write loop, and increment
the loop limit.
Name the device "ttyHV" and pass that to add_preferred_console()
when we're using hypervisor console.
Kill sunhv_console_setup(), it's empty.
Handle the case where we don't want to use hypervisor console.
(ie. we have a head attached to a sun4v machine)
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it can do things like BREAK and HUP, we implement
this as a serial uart driver.
This still needs interrupt probing code, as I haven't figured
out how interrupts will work or be probed for on SUN4V yet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the local 'flip' variable and no need to 'trim' the buffer.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We're presently getting oopses because Bluetooth (and possibly other) drivers
are calling core functions after things have been shut down.
So rather than oopsing, let's drop a warning then take avoiding action, so the
machine survives. Once all the sub-drivers are fixed up we can remove the
take-avoiding-action part.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] mca recovery return value when no bus check
[IA64] SGI SN drivers: don't report !sn2 hardware as an error
[IA64] don't report !sn2 or !summit hardware as an error
[IA64] gensparse_defconfig: turn on PNPACPI
[IA64] Increase severity of MCA recovery messages
This stuff is all in the generic ia64 kernel, and the new initcall error
reporting complains about them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Incorrect uart_write_wakeup() calls cause reference to a NULL tty
pointer. This has been fixed in the sunsab and sunzilog serial drivers
in October 2005. Update the ip22zilog, which is based on sunzilog,
accordingly.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk
early_serial_setup() must not be called after console initialisation.
Add a comment prior to the function explicitly stating this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In kernel bugzilla #5176 (http://bugzilla.kernel.org/show_bug.cgi?id=5176)
Harry R\374ter <h.rueter@gmx.de> points out Documentation/jsm.txt is missing.
No one at Digi seems to care, so just remove the stale reference.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Serial drivers in general should not write uart_info->flags - they're
private to serial_core. Serial drivers have no need to fiddle with
tty->alt_speed, nor manipulate TTY_IO_ERROR in tty->flags. Fix the
ioc4 serial driver for both these points by simply removing the
offending code.
Acked-by: pfg@sgi.com
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds new PCI serial card support.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This replaces old direct usage of tty->flip stuff with relative flip API
calls.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DB1550 actually doesn't have a UART2. Remove it from the list.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On some embedded PowerPC (MPC834x) systems an extra byte would some
times be required to flush data out of the fifo.
serial8250_console_write() was updating the IER in hardware without
also updating the copy in uart_8250_port. This causes issues functions
like serial8250_start_tx() and __stop_tx() to misbehave.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
