If there is a full packet in the buffer, and we overflow that buffer
right after checking for that condition, it would have been possible
for us to block indefinitely (rather, until the next full packet) even if
the file was marked as O_NONBLOCK.
Cc: Jeff Brown <jeffbrown@android.com>
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Without this, it was possible for the reader to get ahead of packet_head.
If the input device generated a partial packet *right* after the reader
got ahead, then we can get into a situation where the device is marked
readable, but read always returns 0 until the next packet is finished
(i.e a SYN is generated by the input driver).
This situation can also happen if we overflow the buffer while a reader
is trying to read an event out.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When runtime power management is enabled put the Samsung keypad driver
into suspend mode with wakeups disabled whenever the device is open but
a key is not actually been pressed. As well as saving a trivial amount of
power this will support the use of SoC wide idle modes which put the entire
device into a retention mode and use explicit wakeup sources to exit.
Since not all of the interrupt controllers used with the driver support
set_irq_wake() (though they all do the right thing) and there's a nasty
WARN() when we disable wake after failing to enable it keep track of the
current wake status from runtime PM and only disable wake if we managed
to enable it; I'm not entirely sure why this doesn't affect the existing
uses of the API in the driver.
System suspend is unaffected as the driver core will runtime resume any
suspended devices prior to system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Conflicts:
drivers/input/keyboard/samsung-keypad.c
This adds a simple device tree binding to the tegra keyboard controller.
Also, mark the default keymap as __devinitdata since it is not referenced
after boot.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some displays from AUO have a so called in-cell touchscreen, meaning it
is built directly into the display unit.
Touchdata is gathered through PIXCIR Tango-ICs and processed in an
Atmel ATmega168P with custom firmware. Communication between the host
system and ATmega is done via I2C.
Devices using this touch solution include the Dell Streak5 and the family
of Qisda ebook readers.
The driver reports single- and multi-touch events including touch area
values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will improve the output of the sensor.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This also changes the devname parameter delivered to
request_threaded_irq() from "mpu_int" to "mpu3050".
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Cintiq 24HD has three LEDs on the left side of the tablet and
three LEDs on the right side of the tablet. Switching to LED 0,
1, or 2 will enable the top, middle, or bottom LED for the respective
side. Switching to LED 3 turns off the LEDs on the respective side.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds support for the Cintiq 24HD. There are two quirks about this
model that haven't been seen in prior tablets. First, a second
touch ring is present on this display; it is being exposed via the
ABS_THROTTLE axis. Second, three capacitive buttons at the top of
the unit are available; though physically a touch strip, we report
the use of these buttons with generic KEY_ events.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver adds support for Sharp's GP2AP002A00F proximity sensor. The
proximity is measured as a binary switch, i.e. an object is either
detected or not detected. Hence, this driver is implemented as a switch
that reports SW_FRONT_PROXIMITY.
Reviewed-by: Datta Shubhrajyoti <shubhrajyoti@ti.com>
Signed-off-by: Courtney Cavin <courtney.cavin@sonyericsson.com>
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These symbols are not used outside it's driver so no need to
make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch converts mc13783-pwrbutton to use the module_platform_driver()
macro which makes the code smaller and a bit simpler.
Also staticise mc13783_pwrbutton_driver which is not used outside
this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Register input device last so that we do not have to reset
input device pointer after calling input_unregister_device().
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Having module device table based on PNP id produces the following warning:
CC drivers/input/touchscreen/htcpen.o
drivers/input/touchscreen/htcpen.c:50: warning: 'pnp_ids' defined but not used
This happens because it is not a PNP driver, bit rather ISA driver and
pnp_ids table is not used anywhere. To fix this issue let's switch to
DMI-based module table instead,
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This variant was introduced in
i2c: boilerplate function for byte swapped smbus_write/read_word_data
This also has the side effect of ensuring any errors from the i2c
read and no longer mangled.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There exist tilt switches that simply report their tilt-state via
some gpios. The number and orientation of their axes can vary
depending on the switch used and the build of the device. Also two
or more one-axis switches could be combined to provide multi-dimensional
orientation.
One example of a device using such a switch is the family of Qisda
ebook readers, where the switch provides information about the
landscape / portrait orientation of the device. The example in
Documentation/input/gpio-tilt.txt documents exactly this one-axis
device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It turns out that v4's firmware provides a command so we can query
the resolution. Let's use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Starting with v3 hardware, the firmware supports this shorter
elantech_send_cmd. Teach the driver to use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The PM methods are basically the same for SPI and I2C busses, so let's
use the same dev_pm_ops for both of them.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the EETI eGalax serial multi touch controller driver.
EETI eGalax serial touch screen controller is a I2C based multiple
capacitive touch screen controller, it can support 5 touch events maximum.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We have determined that the jumpiness previously seen when using
the synaptics kernel mouse driver on OLPC XO was due to not using
the synaptics X11 userspace driver - the xf86-input-evdev driver was
interpreting 'finger near pad' signals as movements. Newer versions
of xf86-input-evdev fix this issue.
Additionally, the synaptics kernel driver is now usable on this
platform, but only when run in relative mode.
Update the comment and refine the check to allow the synaptics driver
to run on OLPC XO in relative mode.
We will continue investigating the EC issue as time becomes available.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is nothing in keypad platform definitions that requires
the driver be complied on Samsung platform only, so let's move them
out of the platform subdirectory and relax the dependencies.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, the synaptics driver puts the device into Absolute mode.
As explained in the synaptics documentation section 3.2, in this mode,
the device sends a continuous stream of packets at the maximum rate
to the host when the user's fingers are near or on the pad or
pressing buttons, and continues streaming for 1 second afterwards.
These packets are even sent when there is no new information to report,
even when they are duplicates of the previous packet.
For embedded systems this is a bit much - it results in a huge
and uninterrupted stream of interrupts at high rate.
This patch adds support for Relative mode, which can be selected as
a new psmouse protocol. In this mode, the device does not send duplicate
packets and acts like a standard PS/2 mouse. However, synaptics-specific
functionality is still available, such as the ability to set the packet
rate, and rather than disabling gestures and taps at the hardware level
unconditionally, a 'synaptics_disable_gesture' sysfs attribute has
been added to allow control of this functionality.
This solves a long standing OLPC issue: synaptics hardware enables
tap to click by default (even in the default relative mode), but we
have found this to be inappropriate for young children and first
time computer users. Enabling the synaptics driver disables tap-to-click,
but we have previously been unable to use this because it also enables
Absolute mode, which is too "spammy" for our desires and actually
overloads our EC with its continuous stream of packets. Now we can enable
the synaptics driver, disabling tap to click while retaining the less
noisy Relative mode.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With commit 67d0a07544 we mark strict_strtox
as obsolete. Convert all remaining such uses in drivers/input/.
Also change long to appropriate types, and return error conditions
from kstrtox separately, as Dmitry sugguests.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix the following compilation failure with v3.2-rc1 by including module.h:
CC drivers/input/serio/ams_delta_serio.o
drivers/input/serio/ams_delta_serio.c:33:15: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c:34:20: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c:35:16: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c: In function 'ams_delta_serio_init':
drivers/input/serio/ams_delta_serio.c:155:2: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/input/serio/ams_delta_serio.c:155:2: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes some v3 hardware (fw_version: 0x150500) wrongly detected
as v2 hardware.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Tested-By: Marc Dietrich <marvin24@gmx.de>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for two ALPS touchpad protocols not
supported currently by the driver, which I am arbitrarily naming
version 3 and version 4. Support is single-touch only at this time,
although both protocols are capable of limited multitouch support.
Thanks to Andrew Skalski, who did the initial reverse-engineering
of the v3 protocol.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for version 4 protocol support, which has 8-byte
data packets, remove all hard-coded assumptions about packet size
and use psmouse->pktsize instead.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for adding support for more ALPS protocol versions,
add a field for the protocol version to the model info instead of
using a field in the flags. OLDPROTO and !OLDPROTO are now called
version 1 and version 2, repsectively.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for new protocol support, move the protocol
information currently documented in alps.c to
Documentation/input/alps.txt, where it can be expanded without
cluttering up the driver.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo's Pen and Touch packets always start with a value
of 0x02 in first byte. In 3rd gen Bamboo's, the hw is now
periodically sending some additional packets with unrelated data
and uses a value other than 0x02 to inform driver this.
Ignore those packets now.
This was reported by users as bad behavior in Gimp. The
invalid packets being processed made the stylus report
out of proximity for the 1 packet and this triggered some
secondary bug which caused Gimp to stop drawing until
user really took pen out of proximity of tablet.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
