Use DMI to:
1. enable polling (BIOS thermal events are broken)
2. disable active trip points (BIOS fan control is broken)
3. disable passive trip point (BIOS hard-codes it too low)
The actual temperature reading does work,
and with the aid of polling, the critical
trip point should work too.
http://bugzilla.kernel.org/show_bug.cgi?id=8842
Signed-off-by: Len Brown <len.brown@intel.com>
thermal.act=-1 disables all active trip points
in all ACPI thermal zones.
thermal.act=C, where C > 0, overrides all lowest temperature
active trip points in all thermal zones to C degrees Celsius.
Raising this trip-point may allow you to keep your system silent
up to a higher temperature. However, it will not allow you to
raise the lowest temperature trip point above the next higher
trip point (if there is one). Lowering this trip point may
kick in the fan sooner.
Note that overriding this trip-point will disable any BIOS attempts
to implement hysteresis around the lowest temperature trip point.
This may result in the fan starting and stopping frequently
if temperature frequently crosses C.
WARNING: raising trip points above the manufacturer's defaults
may cause the system to run at higher temperature and shorten
its life.
Signed-off-by: Len Brown <len.brown@intel.com>
thermal.nocrt=1 disables actions on _CRT and _HOT
ACPI thermal zone trip-points. They will be marked
as <disabled> in /proc/acpi/thermal_zone/*/trip_points.
There are two cases where this option is used:
1. Debugging a hot system crossing valid trip point.
If your system fan is spinning at full speed,
be sure that the vent is not clogged with dust.
Many laptops have very fine thermal fins that are easily blocked.
Check that the processor fan-sink is properly seated,
has the proper thermal grease, and is really spinning.
Check for fan related options in BIOS SETUP.
Sometimes there is a performance vs quiet option.
Defaults are generally the most conservative.
If your fan is not spinning, yet /proc/acpi/fan/
has files in it, please file a Linux/ACPI bug.
WARNING: you risk shortening the lifetime of your
hardware if you use this parameter on a hot system.
Note that this refers to all system components,
including the disk drive.
2. Working around a cool system crossing critical
trip point due to erroneous temperature reading.
Try again with CONFIG_HWMON=n
There is known potential for conflict between the
the hwmon sub-system and the ACPI BIOS.
If this fixes it, notify lm-sensors@lm-sensors.org
and linux-acpi@vger.kernel.org
Otherwise, file a Linux/ACPI bug, or notify
just linux-acpi@vger.kernel.org.
Signed-off-by: Len Brown <len.brown@intel.com>
"thermal.psv=-1" disables passive trip points
for all ACPI thermal zones.
"thermal.psv=C", where 'C' is degrees Celsius,
overrides all existing passive trip points
for all ACPI thermal zones.
thermal.psv is checked at module load time,
and in response to trip-point change events.
Note that if the system does not deliver thermal zone
temperature change events near the new trip-point,
then it will not be noticed. To force your custom
trip point to be noticed, you may need to enable polling:
eg. thermal.tzp=3000 invokes polling every 5 minutes.
Note that once passive thermal throttling is invoked,
it has its own internal Thermal Sampling Period (_TSP),
that is unrelated to _TZP.
WARNING: disabling or raising a thermal trip point
may result in increased running temperature and
shorter hardware lifetime on some systems.
Signed-off-by: Len Brown <len.brown@intel.com>
Thermal Zone Polling frequency (_TZP) is an optional ACPI object
recommending the rate that the OS should poll the associated thermal zone.
If _TZP is 0, no polling should be used.
If _TZP is non-zero, then the platform recommends that
the OS poll the thermal zone at the specified rate.
The minimum period is 30 seconds.
The maximum period is 5 minutes.
(note _TZP and thermal.tzp units are in deci-seconds,
so _TZP = 300 corresponds to 30 seconds)
If _TZP is not present, ACPI 3.0b recommends that the
thermal zone be polled at an "OS provided default frequency".
However, common industry practice is:
1. The BIOS never specifies any _TZP
2. High volume OS's from this century never poll any thermal zones
Ie. The OS depends on the platform's ability to
provoke thermal events when necessary, and
the "OS provided default frequency" is "never":-)
There is a proposal that ACPI 4.0 be updated to reflect
common industry practice -- ie. no _TZP, no polling.
The Linux kernel already follows this practice --
thermal zones are not polled unless _TZP is present and non-zero.
But thermal zone polling is useful as a workaround for systems
which have ACPI thermal control, but have an issue preventing
thermal events. Indeed, some Linux distributions still
set a non-zero thermal polling frequency for this reason.
But rather than ask the user to write a polling frequency
into all the /proc/acpi/thermal_zone/*/polling_frequency
files, here we simply document and expose the already
existing module parameter to do the same at system level,
to simplify debugging those broken platforms.
Note that thermal.tzp is a module-load time parameter only.
Signed-off-by: Len Brown <len.brown@intel.com>
"thermal.off=1" disables all ACPI thermal support at boot time.
CONFIG_ACPI_THERMAL=n can do this at build time.
"# rmmod thermal" can do this at run time,
as long as thermal is built as a module.
WARNING: On some systems, disabling ACPI thermal support
will cause the system to run hotter and reduce the
lifetime of the hardware.
Signed-off-by: Len Brown <len.brown@intel.com>
Make the needlessly global "acpi_event_seqnum" static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Send key=value pair along with the uevent instead of a plain value so that
userspace (udev) can handle it like common environment variables.
Signed-off-by: Holger Macht <hmacht@suse.de>
Acked-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Stephan Berberig <s.berberig@arcor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There must not be a new-line character in the uevent. Otherwise, udev gets
confused. Thanks to Kay Sievers for pointing it out.
Signed-off-by: Stephan Berberig <s.berberig@arcor.de>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
gcc-4.2 is a lot more picky about its symbol handling. EXPORT_SYMBOL no
longer works on symbols that are undefined or defined with static scope.
For example, with CONFIG_PROFILE off, I see:
kernel/profile.c:206: error: __ksymtab_profile_event_unregister causes a section type conflict
kernel/profile.c:205: error: __ksymtab_profile_event_register causes a section type conflict
This patch moves the EXPORTs inside the #ifdef CONFIG_PROFILE, so we
only try to export symbols that are defined.
Also, in kernel/kprobes.c there's an EXPORT_SYMBOL_GPL() for
jprobes_return, which if CONFIG_JPROBES is undefined is a static
inline and gives the same error.
And in drivers/acpi/resources/rsxface.c, there's an
ACPI_EXPORT_SYMBOPL() for a static symbol. If it's static, it's not
accessible from outside the compilation unit, so should bot be exported.
These three changes allow building a zx1_defconfig kernel with gcc 4.2
on IA64.
[akpm@linux-foundation.org: export jpobe_return properly]
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch addresses some issues in x86/x86-64 acpi-cpufreq driver:
1. Current memory allocation for acpi_perf_data is actually open-coded
alloc_percpu(). The patch defines and handles acpi_perf_data as percpu
data. The code will be cleaner and easier to be maintained with this
change.
2. Won't load driver in acpi_cpufreq_early_init() failure case.
3. Add __init for acpi_cpufreq_early_init().
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Enable C3 without bm control only for CST based C3.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove dead code spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes an obvious use-after-free introduced by
commit 837012ede1.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some ASUS laptops fail to use boot time EC
and need to eventually switch to one described in DSDT.
http://bugzilla.kernel.org/show_bug.cgi?id=8709
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some ASUS laptops access EC space from device _INI methods, but do not
provide ECDT for early EC setup. In order to make them function properly,
there is a need to find EC is DSDT before any _INI is called.
Similar functionality was turned on by acpi_fake_ecdt=1 command line
before. Now it is on all the time.
http://bugzilla.kernel.org/show_bug.cgi?id=8598
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI: EC: Handler for query 0x57 is not found!
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
CONFIG_ACPI_PROCFS_SLEEP is a NO-OP -- delete it (again).
Apparently 296699de6b creating CONFIG_SUSPEND
and CONFIG_PM_SLEEP was based on an out-dated version of drivers/acpi/Kconfig,
as it erroneously restored this recently deleted config option.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restore the 2.6.22 CONFIG_ACPI_SLEEP build option, but now shadowing the
new CONFIG_PM_SLEEP option.
Signed-off-by: Len Brown <len.brown@intel.com>
[ Modified to work with the PM config setup changes. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce CONFIG_SUSPEND representing the ability to enter system sleep
states, such as the ACPI S3 state, and allow the user to choose SUSPEND
and HIBERNATION independently of each other.
Make HOTPLUG_CPU be selected automatically if SUSPEND or HIBERNATION has
been chosen and the kernel is intended for SMP systems.
Also, introduce CONFIG_PM_SLEEP which is automatically selected if
CONFIG_SUSPEND or CONFIG_HIBERNATION is set and use it to select the
code needed for both suspend and hibernation.
The top-level power management headers and the ACPI code related to
suspend and hibernation are modified to use the new definitions (the
changes in drivers/acpi/sleep/main.c are, mostly, moving code to reduce
the number of ifdefs).
There are many other files in which CONFIG_PM can be replaced with
CONFIG_PM_SLEEP or even with CONFIG_SUSPEND, but they can be updated in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace CONFIG_SOFTWARE_SUSPEND with CONFIG_HIBERNATION to avoid
confusion (among other things, with CONFIG_SUSPEND introduced in the
next patch).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's a totally independent decision for the user whether he wants
suspend and/or hibernation support, and ACPI shouldn't care.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"acpi_no_auto_ssdt" prevents Linux from automatically loading
all the SSDTs listed in the RSDT/XSDT.
This is needed for debugging. In particular,
it allows a DSDT override to optionally be a DSDT+SSDT override.
http://bugzilla.kernel.org/show_bug.cgi?id=3774
Signed-off-by: Len Brown <len.brown@intel.com>
As it was a synonym for (CONFIG_ACPI && CONFIG_X86),
the ifdefs for it were more clutter than they were worth.
For ia64, just add a few stubs in anticipation of future
S3 or S4 support.
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI Exception (processor_throttling-0084): AE_NOT_FOUND, Evaluating _PTC [20070126]
ACPI Exception (processor_throttling-0147): AE_NOT_FOUND, Evaluating _TSS [20070126]
These methods are optional, so Linux should not
alarm users when they are not found.
http://bugzilla.kernel.org/show_bug.cgi?id=8802
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Luming Yu <luming.yu@intel.com>
Remove references to ACPI_STATE_S2, introduced by
acpi-implement-the-set_target-callback-from-pm_ops.patch, from acpi_pm_enter().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The SMP dependency on HOTPLUG_CPU and SUSPEND_SMP
caused more harm than good -- making ACPI sleep
support vanish for configs missing those options.
So simply select them on the (ACPI && SMP && X86) systems
that need them.
Also, remove the prompt for ACPI_SLEEP,
virtually nobody (intentionally) enables ACPI without it.
Signed-off-by: Len Brown <len.brown@intel.com>
/proc/acpi/sleep has had its own "default n" option,
ACPI_SLEEP_PROC_SLEEP, for many months.
Time to delete ACPI_SLEEP_PROC_SLEEP.
Users that still need /proc/acpi/sleep can still get it
along with the other deprecated /proc/acpi files
by enabling CONFIG_ACPI_PROCFS.
Also delete ACPI_SLEEP_PROC_FS, which was an umbrella
for /proc/acpi/sleep, wakeup, alarm, because it was
effectively just a synonym for ACPI_SLEEP.
Signed-off-by: Len Brown <len.brown@intel.com>
delete "default y" from CONFIG_ACPI_PROCFS
(effectively making the default 'N')
List exactly what /proc files this option controls,
and clarify that it doesn't change non-deprecated files.
Signed-off-by: Len Brown <len.brown@intel.com>
modpost is going to use these to create e.g. acpi:ACPI0001
in modules.alias.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Modify modpost (file2alias.c) to add acpi*:XYZ0001: alias in modules.alias
like:
grep acpi /lib/modules/2.6.22-rc4-default/modules.alias
alias acpi*:SNY5001:* sony_laptop
alias acpi*:SNY6001:* sony_laptop
for e.g. the sony_laptop module.
This module matches against all ACPI devices with a HID or CID of SNY5001
or SNY6001
Export an uevent and modalias sysfs file containing the string:
[MODALIAS=]acpi:PNP0C0C:
additional CIDs are concatenated at the end.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Define standardized HIDs - Rename current acpi_device_id to acpica_device_id
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
leds: cr_bllcd.c: build fix
backlight: Convert from struct class_device to struct device
backlight: Fix order of Kconfig entries
Based on the David Brownell's patch at
http://marc.info/?l=linux-acpi&m=117873972806360&w=2
updated by: Rafael J. Wysocki <rjw@sisk.pl>
Add a helper routine returning the lowest power (highest number) ACPI device
power state that given device can be in while the system is in the sleep state
indicated by acpi_target_sleep_state .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
In the future some drivers may need to use ACPI to determine the low power
states in which to place their devices, but to provide the drivers with this
information the ACPI core needs to know what sleep state the system is going to
enter. Namely, the device's state should not be too high power for given system
sleep state and, if the device is supposed to be able to wake up the system, its
state should not be too low power for the wake up to be possible). For this
purpose, the ACPI core needs to implement the set_target() method in 'struct
pm_ops' and store the target system sleep state passed by the PM core in a
variable.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Len Brown <len.brown@intel.com>
The file name is the signature, such as DSDT,
and the contents are the binary table image.
Some tables, such as the SSDT, can have multiple instances.
If just one, the file is SSDT, but if 3 instances,
for example, it will be SSDT1, SSDT2, SSDT3
All static tables (besides teh RSDP and RSDT themselves
are exported. Dynamic tables, such as SSDT op-regions that
are not declared in the RSDT, will be added in a subsequent patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split ACPI_DEBUG into function trace enabled and not enabled.
Function trace is most of the ACPI_DEBUG costs, but is
not much of use for kernel ACPI debugging.
Size of kernel image increased on test compile:
+ 48k (Full ACPI_DEBUG)
+ 35k (ACPI_DEBUG with function trace compiled out)
Performance without function trace is also much better.
Also remove ACPI_LV_DEBUG_OBJECT from default debug level as
a lot vendors let Store (value, debug) in their code and this
might confuse users when it pops up in syslog.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This is an incremental patch for the recent genetlink
multicast changes.
Now ACPI events are exported via generic netlink multicast group.
Thanks for Johannes' help on developing this patch
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI has a ton of macros which make a bunch of empty if's when configured
in non-debug mode.
[lenb: The code it complaines about is functionally correct,
so this patch is just to make -Wextra happier]
#define DBG()
if(...)
DBG();
next_c_statement
which turns into
if(...) ;
next_c_statement
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
For NUMA emulation, our SLIT should represent the true NUMA topology of the
system but our proximity domain to node ID mapping needs to reflect the
emulated state.
When NUMA emulation has successfully setup fake nodes on the system, a new
function, acpi_fake_nodes() is called. This function determines the proximity
domain (_PXM) for each true node found on the system. It then finds which
emulated nodes have been allocated on this true node as determined by its
starting address. The node ID to PXM mapping is changed so that each fake
node ID points to the PXM of the true node that it is located on.
If the machine failed to register a SLIT, then we assume there is no special
requirement for emulated node affinity so we use the default LOCAL_DISTANCE,
which is newly exported to this code, as our measurement if the emulated nodes
appear in the same PXM. Otherwise, we use REMOTE_DISTANCE.
PXM_INVAL and NID_INVAL are also exported to the ACPI header file so that we
can compare node_to_pxm() results in generic code (in this case, the SRAT
code).
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In acpi_scan_nodes(), we immediately return -1 if acpi_numa <= 0, meaning
we haven't detected any underlying ACPI topology or we have explicitly
disabled its use from the command-line with numa=noacpi.
acpi_table_print_srat_entry() and acpi_table_parse_srat() are only
referenced within drivers/acpi/numa.c, so we can mark them as static and
remove their prototypes from the header file.
Likewise, pxm_to_node_map[] and node_to_pxm_map[] are only used within
drivers/acpi/numa.c, so we mark them as static and remove their externs
from the header file.
The automatic 'result' variable is unused in acpi_numa_init(), so it's
removed.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Prevent people from directly including <asm/rwsem.h>.
[IA64] remove time interpolator
[IA64] Convert to generic timekeeping/clocksource
[IA64] refresh some config files for 64K pagesize
[IA64] Delete iosapic_free_rte()
[IA64] fallocate system call
[IA64] Enable percpu vector domain for IA64_DIG
[IA64] Enable percpu vector domain for IA64_GENERIC
[IA64] Support irq migration across domain
[IA64] Add support for vector domain
[IA64] Add mapping table between irq and vector
[IA64] Check if irq is sharable
[IA64] Fix invalid irq vector assumption for iosapic
[IA64] Use dynamic irq for iosapic interrupts
[IA64] Use per iosapic lock for indirect iosapic register access
[IA64] Cleanup lock order in iosapic_register_intr
[IA64] Remove duplicated members in iosapic_rte_info
[IA64] Remove block structure for locking in iosapic.c
This is a merge of Peter Keilty's initial patch (which was
revived by Bob Picco) for this with Hidetoshi Seto's fixes
and scaling improvements.
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Introduce the pm_power_off_prepare() callback that can be registered by the
interested platforms in analogy with pm_idle() and pm_power_off(), used for
preparing the system to power off (needed by ACPI).
This allows us to drop acpi_sysclass and device_acpi that are only defined in
order to register the ACPI power off preparation callback, which is needed by
pm_power_off() registered in a much different way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we are now explicitly calling hibernation_ops->prepare() before
hibernation_ops->enter() in hibernation_platform_enter() (defined in
kernel/power/disk.c), ACPI should not call acpi_sleep_prepare(ACPI_STATE_S4)
from acpi_shutdown().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At least on some machines it is necessary to prepare the ACPI firmware for the
restoration of the system memory state from the hibernation image if the
"platform" mode of hibernation has been used. Namely, in that cases we need
to disable the GPEs before replacing the "boot" kernel with the "frozen"
kernel (cf. http://bugzilla.kernel.org/show_bug.cgi?id=7887). After the
restore they will be re-enabled by hibernation_ops->finish(), but if the
restore fails, they have to be re-enabled by the restore code explicitly.
For this purpose we can introduce two additional hibernation operations,
called pre_restore() and restore_cleanup() and call them from the restore code
path. Still, they should be called if the "platform" mode of hibernation has
been used, so we need to pass the information about the hibernation mode from
the "frozen" kernel to the "boot" kernel in the image header.
Apparently, we can't drop the disabling of GPEs before the restore because of
Bug #7887 . We also can't do it unconditionally, because the GPEs wouldn't
have been enabled after a successful restore if the suspend had been done in
the 'shutdown' or 'reboot' mode.
In principle we could (and probably should) unconditionally disable the GPEs
before each snapshot creation *and* before the restore, but then we'd have to
unconditionally enable them after the snapshot creation as well as after the
restore (or restore failure) Still, for this purpose we'd need to modify
acpi_enter_sleep_state_prep() and acpi_leave_sleep_state() and we'd have to
introduce some mechanism synchronizing the disablind/enabling of the GPEs with
the device drivers' .suspend()/.resume() routines and with
disable_/enable_nonboot_cpus(). However, this would have affected the
suspend (ie. s2ram) code as well as the hibernation, which I'd like to avoid
in this patch series.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On systems that do not have pm2_control_block, we cannot really use
ARB_DISABLE before C3. We used to disable C3 totally on such systems.
To be compatible with Windows, we need to enable C3 on such systems now.
We just skip ARB_DISABLE step before entering the C3-state and assume
hardware is handling things correctly. Also, ACPI spec is not clear
about pm2_control is _needed_ for C3 or not.
We have atleast one system that need this to enable C3.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_ev_pci_config_region_setup() leaks pci_id
in the error case of "if (!pci_device_node)"
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Data returned by acpi_get_name in acpi_buffer is not acpi_object and
therefore should not be cast to it, otherwise we'll get an nice oops
trying to print error message.
Also print name of the ACPI object corresponding to the docking station
and elevate severity of the message printed when _DCK fails to KERN_ERR.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Various pieces of code around the kernel want to be able to trigger an
orderly poweroff. This pulls them together into a single
implementation.
By default the poweroff command is /sbin/poweroff, but it can be set
via sysctl: kernel/poweroff_cmd. This is split at whitespace, so it
can include command-line arguments.
This patch replaces four other instances of invoking either "poweroff"
or "shutdown -h now": two sbus drivers, and acpi thermal
management.
sparc64 has its own "powerd"; still need to determine whether it should
be replaced by orderly_poweroff().
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David S. Miller <davem@davemloft.net>
Convert the backlight and LCD classes from struct class_device
to struct device since class_device is scheduled for removal.
One nasty API break is the backlight power attribute has had to be
renamed to bl_power and the LCD power attribute has had to be renamed
to lcd_power since the original names clash with the core. I can't see
a way around this.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Upon ACPI events, send an "acpi_event" via Generic Netlink.
This is in addition to /proc/acpi/event, which remains intact for now.
Thanks to Jamal for his great help.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem with the internal FADT conversion where ACPI 1.0
FADTs that contained invalid non-zero values in reserved fields
could cause later failures because these fields have meaning in
later revisions of the FADT. For incoming ACPI 1.0 FADTs, these
fields are now always zeroed. (Preferred_PM_Profile, PSTATE_CNT,
CST_CNT, IAPC_BOOT_FLAGS.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem in acpi_ev_delete_gpe_xrupt where the global interrupt
list could be corrupted if the interrupt being removed was at
the head of the list. Reported by Linn Crosetto.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Latest update for the Windows strings, with comments. Removed
unused strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If we have quirk "init... after standby", we should not be calling it while
resuming from hibernation. And... that quirk is only ever needed on toshiba
4030cdt... and... noone should be using standby these days, anyway.
That quirk was certainly _not_ meant to be ran after hibernation.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently the acpi video module export the backlight interface to sysfs
also if acpi_video_device_lcd_query_levels() fails to read _BLC method
(e.g. because the method is not available). In this case the userspace
don't know which brightness level are supported and can't set a brightness
level (echo return with: "write error: Invalid Argument"). This happend
e.g. on a ASUS RF1 (correct supported by the asus-laptop module).
The video module should not export the backlight interface if query _BLC fail,
because you can't set anything from userspace and this make it useless.
http://bugzilla.kernel.org/show_bug.cgi?id=8375
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Acked-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
make the needlessly global osi_linux static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
make 2 needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Need to check for special case "acpi_osi=!Linux" before handling the
general case "acpi_osi=!*", or it will have no effect.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If asus_acpi_init doesn't find any device it knows about, it mistakenly
returns a "success" error code even though it cleans up after itself. Later
when trying to rmmod asus_acpi, the module_exit routine would try to clean up
one more time and we would end up calling
acpi_bus_unregister_driver(&asus_hotk_driver) twice. This patch addresses
this first problem by returning -ENODEV when no appropriate device is found.
Then there was also another bug with the code handling the return value of
backlight_device_register. If this function ever failed, the driver would
cleanup by calling the module_exit routine from module_init, but it would
still return "success". So any attempt to rmmod this module would result in
asus_acpi_exit being called twice but it's not ready to handle it (I haven't
hit this bug, just found it by code inspection). This patch fixes that by
inserting a return -ENODEV; at the end of this error handling path.
Signed-off-by: Maxime Austruy <maxime@tralhalla.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Always disable/enable interrupts in the acpi idle routine,
even in the error path.
This is required as the 2.6.20 change in git commit d331e739f5ad2aaa9...
"Fix interrupt race in idle callback" expects the idle handler
to enable interrupt before returning.
There was a case in acpi idle routine, in which interrupt was not being
enabled before return, which caused the system to hang at bootup, while
enabling C-states on an SMP system.
The signature of the hang was that "processor.nocst"
was required to enable boot.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
asus_acpi_init() has a hack to prevent the driver from loading
when asus_hotk_add() fails. However, it was returning the successful
return value of acpi_bug_registger_driver() on failure. This caused
an oops on unload. Instead it should return -ENODEV.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
In the routine acpi_ut_create_package_object(), if the
ACPI_ALLOCATE_ZEROED() fails then ACPI_FREE(package_desc) is called as
part of the cleanup. This should instead be
acpi_ut_remove_reference(package_desc) in order to remove the reference
acquired from acpi_ut_create_internal_object() [see the routine
acpi_ut_create_buffer_object() as an example of proper functionality].
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
