This change fixes up saa7127_s_std() generate SECAM out, if the user has
requested a 50 Hz video standard set that only contains a request for SECAM
standards and not PAL. Only the SAA712[89] chips can generate SECAM, the
SAA712[67] chips cannot.
I was unclear on the burst start and end values - I couldn't figure out
the units - so I left them the same as for the PAL systems.
A the video decoders on both a PVR-350 (SAA7115) and an HVR-1600 (CX23418)
identify the SECAM signal generated by a SAA7129 with this patch as SECAM.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the "xceive_pin" setting from "15" to "1" for the PVR2100 -- the same as
the PVR3100H. This properly resets the XC2028 tuner on the PVR2100.
Sergey's original email report:
Hi.
Seems cx18 module has incorrect .xceive_pin value for card,
as i see lots of i2c errors in dmesg from xc2028.
i'm using 2.6.32.2, my hardware is:
00:09.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23418
Single-Chip MPEG-2 Encoder with Integrated Analog Video/Broadcast Audio Decoder
[14f1:5b7a]
Subsystem: LeadTek Research Inc. Device [107d:6f27]
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at f0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Kernel driver in use: cx18
Kernel modules: cx18
Following fixes this problem for me, the rest seems working:
Reported-by: Sergey Bolshakov <sbolshakov@altlinux.ru>
Tested-by: Sergey Bolshakov <sbolshakov@altlinux.ru>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX18_CPU_SET_INDEXTABLE command was being called with the wrong number
of arguments causing the index table frame type selection mask to be set wrong.
Now the IDX stream properly sends entries for I, P, and B frames.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_G_ENC_INDEX support see the light of day.
Some notes:
1. With default capture parameters, the CX23418 seems to transfer 192 index
entries (4.5 kB worth) at 10 second intervals.
2. Index streams don't seem to be supported for MPEG 2 TS streams
3. The index entries seem to claim every frame is a B-Frame. Possible
firmware bug.
4. The cx18 driver does not try to capture an index stream when inserting
sliced VBI into the MPEg stream as the offsets would need fixup.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the v4l2 spec, very old MPEG index entries needs to be discarded
in favor of newer index entries. This change ensures the firmware always has
buffers for index entries at the expense of the oldest unread buffers.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change starts the IDX stream along with the MPG stream as an internal
use (only) stream much like the VBI stream can be started as an internal use
stream for inserting sliced VBI packets.
The IDX stream is not started automatically with an MPEG strem if the IDX
stream is disabled (no buffers allocated) or if sliced VBI insertion is being
performed by the cx18 driver. The cx18 driver doing sliced VBI insertion
makes the offsets in the IDX stream inaccurate for the final MPEG stream
presented to user space. Since fixing the IDX offsets ourselves is not easy
and we cannot easily do what ivtv does to fix the offsets, we'll make sliced
VBI insertion and MPEG Index capture mutually exclusive for now.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change allows the IDX stream to be started and stopped as any other
stream even though it has no associated device node. This is needed for
cx18 driver internal use.
Also always tell the CX23418 to generate index entries when an analog capture
starts and the IDX stream has had buffers allocated (i.e. is enabled).
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a long standing memory leak of stream buffers for streams that did not
have a struct video_device allocated: namely the TS and IDX streams.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the module options related to INDEX stream buffer allocation. A single
CX2341[5678] index entry is only 24 bytes. Large buffers for the IDX stream
will prevent the CX23418 from transferring index data over at all. Buffers
of around 1.5 kB or 64 index entries seem to be just fine. We'll default to
63 buffers/MDLs as that is the firmware limit per stream and IDX stream buffers
are not high rate. There is no reason on earth to allocate the previous 1 MB
default of buffer space for the IDX stream.
This is in anticipation of implementing the G_ENC_INDEX ioctl() in the cx18
driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ctrls field of struct sd_desc is declared as const
in gspca.h. It is worth to initialize the content also with
constant values.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function callbacks in sd_desc are defined at compile time and
they do not change at runtime. Make the sd_desc initializations const.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The USB video interface was checked as having the number zero, but
some webcams have other values. The test is now done on the interface
class which may be either 255 (vendor spec) or 0 (class per interface).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- adapt the start sequences from the info file of the ms-win driver
of the webcams 046d:08a2/046d:08aa (lvWIMv.inf)
- disable the brightness for this sensor
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- have 2 tables for sensor probe
- with the same ID, the sensor mi1320 is found with the bridge vc0321,
the sensor mi1320_soc with the bridge vc0323
- add some comments
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added a new initialization method for Aiptek DV T300.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13708
Tested-by: Hámorszky Balázs <balihb@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently all probed sensor types are emitted in the kernel log, generating unnecessary noise. Be less verbose and only report what sensor is found (if any)
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcam 0ac8:303b may have the sensors HV7131B or HV7131R(c).
This changeset checks the HV7131 type.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ID was found in a webcam 0ac8:301b.
Signed-off-by: Luis Maia <lmaia@royalhat.org>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This flag permits subdrivers to create specific transfer URBs.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improves ATBM8830 reception by using per card AGC configuration rather
than register default.
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some unknown reason, on a MacBookPro5,3 the iSight sometimes report
a different video format GUID. This patch add the other (wrong) GUID to
the format table, making the iSight work always w/o other problems.
What it should report: 32595559-0000-0010-8000-00aa00389b71
What it often reports: 32595559-0000-0010-8000-000000389b71
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The quirks module parameter is or'ed with the built-in quirks for the
device being probed. This make it impossible to disable a built-in quirk
without recompiling the driver.
Replace the built-in quirks with the quirks module parameter instead of
or'ing the values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The realtime clock provided by do_gettimeofday() is affected by time
jumps caused by NTP or DST. Furthermore, preliminary investigation
showed that SMP systems the realtime clock is based on the CPU TSC,
and those could get slightly out of sync, resulting in jitter in the
timestamps depending on which processor handles the USB interrupts.
Instead of the realtime clock, use a monotonic high resolution clock to
timestamp the buffer. As this could in theory introduce a regression
with some userspace applications expecting a realtime clock timestamp,
add a module parameter to switch back to the realtime clock.
Thanks to Paulo Assis for pointing out and investigating the issue.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When preparing the linux-next patches, I got those errors:
include/media/ir-core.h:29: warning: left shift count >= width of type
In file included from include/media/ir-common.h:29,
from drivers/media/video/ir-kbd-i2c.c:50:
drivers/media/video/ir-kbd-i2c.c: In function ‘ir_probe’:
drivers/media/video/ir-kbd-i2c.c:324: warning: left shift count >= width of type
Unfortunately, enum is 32 bits on i386. As we define IR_TYPE_OTHER as 1<<63,
it won't work on non 64 bits arch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Experimental patch to allow changing the IR protocol. Currently, it support
changing between RC-5 and NEC protocols.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds an structure to ir_input_register to contain IR device characteristics,
like supported protocols and a callback to handle protocol event changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move I2C IR initialization from just after I2C bus setup to right
before non-I2C IR initialization. This avoids the case where an I2C IR
device is blocking audio support (at least the PV951 suffers from
this). It is also more logical to group IR support together,
regardless of the connectivity.
This fixes bug #15184:
http://bugzilla.kernel.org/show_bug.cgi?id=15184
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Regression was caused by my commit 6b35ca0d3d
which determined message size using sizeof rather than hardcoded constants.
Unfortunately pwc_set_shutter_speed reuses a 2 byte buffer for a one byte
message too so the sizeof was bogus in this case.
All other uses of sizeof checked and are ok.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This polling is needed if camera is in standby mode, but current exiting
condition is inverted.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An earlier commit removed the lock_kernel/unlock_kernel pair but forgot
to remove the unlock_kernel call in the cleanup path at the end of the
function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some customers has problem with quality of DVB-T
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/446575
After this patch http://patchwork.kernel.org/patch/23345/
This is patch for fix regression with DVB-T. Tested with many people.
Signed-off-by: Alexey Osipov <lion-simba@pridelands.ru>
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the following compiler warning: 'dummy' is used uninitialized in this function.
Although the result in the dummy variable is not used the program flow in
soc_camera_limit_side() depends on the value in dummy. The program flow is better
to be deterministic.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Cc: David Vrabel <dvrabel@arcom.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Cc: David Vrabel <dvrabel@arcom.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Antonio Ospite <ospite@studenti.unina.it>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: linux-media@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Quickcam Web camera would not produce an image if you removed and inserted the module multiple times without physically power cycling the camera first.
By writing zero to bridge register STV_SCAN_RATE (0x1443) the camera works as intended, regardless of the number of module insertions.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a vflip quirk for the Fujitsu-Siemens Amilo Xi 2428. Thanks to Myroslav Zapukhlyak for reporting.
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
