Simplify essentially duplicate load RISC RAM implementation
in qla2x00_load_ram_ext() and qla2x00_load_ram().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Swing/emphasis settings in NVRAM were not being honoured due
to the driver not converting the serial-link options from LE
to host-endian format.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the Get Port Database call fails during local-loop
update, then schedule the DPC routine to perform a rescan as
the firmware would have updated the Get ID List port-entries
of their new state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transition driver to exclusively use the request_firmware()
interfaces to retrieve firmware-blobs from user-space. This
will be the default behaviour going forward until the
embedded firmware-binary images are removed from the
upstream kernel.
Upon request, the driver caches the firmware image until the
driver is unloaded.
NOTE: The option is present to allow the user to continue to
use the firmware-loader modules, but, should be considered
deprecated.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A regression in a recent change
33135aa2a5 caused the driver
to mistakenly drop handling of AENs. Due to the incorrect
handling, ports would not reappear after RSCNs and LIPs.
Drops unused/incorrect compound #define from qla_def.h.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A driver must wait 100us before attempting an MMIO operation
to the RISC after a soft-reset has been initiated. A
similar delay was needed with earlier ISPs.
Note: a PCI config-space read is used to flush the MMIO
write to the ISP, since the ISP's state machines are unable
to respond to any MMIO read during the reset process.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When mulitple initiators are coming up in an FCAL topology.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the drivers/scsi/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/scsi/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ISP23xx and ISP24xx chips have support for an adaptive
method of posting SCSI command completions for multiple SCSI
commands during a single system interrupt.
SCSI commands are placed on the system response queue
without interrupting the host until 1) a delay timer
expires; or 2) a SCSI command completes with an error.
As long as the host software (qla2xxx) services the response
queue for completions (this polling is done during
queuecommand()) within the 'delay timer' period, the
firmware will not generate system interrupt.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The non-handled failure cases of the Fabric Login mailbox
command handling logic would incorrectly mark the fcport as
dead and not allow the standard port-down-retry-count logic
to manage the transition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original implementation used an overloaded bit in the EFI
parameters. The correct bit is BIT_4 of the special_options
section of NVRAM.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In an FL topology, limit port recognition to those devices
not within the same area and domain of the ISP. The
firmware will recogonize such devices during local-loop
discovery.
Some devices may respond to a PLOGI before they have
completed their fabric login or they may not be a public
device. In this case they will report:
domain == 00
area == 00
alpa == <XX>
which is valid. Exclude such devices from local loop
discovery.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Export COS information for the fc_host and fc_remote_port
objects added by the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanup FC remote port registration.
Due to the inherent behaviour (an immediate scan) of adding
a 'target'-role-capable rport via fc_remote_port_add(),
split the registration into two steps -- addition as
unknown-type role, then use fc_remote_port_rolchg() with
appropriate role (based on PLOGI/PRLI bits). This allows
for a more cleaner rport->dd_data management as can be seen
with the simplified qla2xxx_slave_alloc() function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Consolidate ISP24xx chip reset logic.
Consolidate near-duplicate RISC reset logic from
qla24xx_reset_chip() and qla24xx_chip_diag(). Also, after
initiating a soft-reset, insure the firmware has completed
all NVRAM accesses before continuing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct maximum supported lun and target-id definitions.
The driver uses command-IOCBs which support a maximum lun
value of 0xffff -- correct #define to reflect the change.
Also, remove superfluous MAX_TARGET definition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx definitions.
Add requisite structure definitions and #define's for ISP24xx
support. Also drop volatile modifiers from device_reg_* register
layouts as the members are never really accessed, only their
offsets within the layout are used during reads and writes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Factor-out ISP specific functions to method-based call tables.
In anticipation of ISP24xx/ISP25xx support, factor-out ISP
specific functions into a method-based call table.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original from: Christoph Hellwig <hch@lst.de>
Modified and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove internal lun discovery routines and support
structures.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add initial support for FC remote port infrastructure.
o Use fc_remote_port...() registration and block/unlock
functions.
o Consolidate 'attribute' (fc-remote/sysfs) helpers into
new qla_attr.c file.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove internal command queuing from the driver. As is, this
driver cannot tolerate cable-pulls as I/Os will begin to fail
by the upper layers.
o Should be used in conjuction with the
11-fc_rport_adds_2.diff patch.
o Removes qla_listops.h file -- no longer needed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
