New typedefs are usually frowned upon. This patch changes
libertas_adapter -> struct libertas_adapter
libertas_priv -> struct libertas_priv
While passing, make everything checkpatch.pl-clean that gets touches.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies the namespace of variables, functions defines
and structures. It does:
- rename libertas_XXX to lbs_XXX
- rename LIBERTAS_XXX to lbs_XXX
- rename wlan_XXX to lbs_XXX
- rename WLAN_XXX to LBS_XXX (but only those that were
defined in libertas-local *.h files, e.g. not defines
from net/ieee80211.h)
While passing, I fixed some checkpatch.pl errors too.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few fields being converted to the wrong sized type, and a few missed
endian conversions.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver support for the monitor mode support that will be available in the next
OLPC 'bleeding edge' Marvell firmware release (most likely, 5.110.16.p2).
To activate monitor mode,
echo mode > /sys/class/net/{ethX,mshX}/device/libertas_rtap
where mode is the hex mask that specifies which frames to sniff (in short, 0x1
for data, 0x2 for all management but beacons, 0x4 for beacons). Any non zero
mode will activate the monitor mode, inhibiting transmission in ethX and mshX
interfaces and routing all the incoming traffic to a new rtapX interface that
will output the packets in 802.11+radiotap headers format.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Those two variables were initialized with some default values, but there
is no code that would ever change them. So we could use as well the defaults
directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No code uses the contents of this variable, so it can go.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when you define LBS_DEB_HEX, you get every hex dump in the
whole driver, e.g. for LBS_DEB_CMD, LBS_DEB_RX, LBS_DEB_TX etc. This
patch makes sure that you only get the hexdump that you're interested in.
Renamed lbs_dbg_hex() into lbs_deb_hex(), like the other lbs_deb_XXX()
macros.
Made lbs_deb_hex() issue a line feed (and a new prompt) after 16 bytes.
As lbs_deb_hex() now prints the ":" after the prompt by itself, removed
the misc colons in the various *.c files.
lbs_deb_XXX() now print the debug category as well.
As lbs_deb_XXX() --- and especially lbs_deb_11d() --- now print the
category, I removed various "11D:" prefixes in 11d.c as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is nowhere any place that set's this variable.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused/duplicated fields and consolidate static data rate arrays,
for example the libertas_supported_rates[] and datarates[] arrays in
the bss_descriptor structure, and the libertas_supported_rates field
in the wlan_adapter structure.
Introduce libertas_fw_index_to_data_rate and libertas_data_rate_to_fw_index
functions and use them everywhere firmware requires a rate index rather
than a rate array.
The firmware requires the 4 basic rates to have the MSB set, but most
other stuff doesn't, like WEXT and mesh ioctls. Therefore, only set the MSB
on basic rates when pushing rate arrays to firmware instead of doing a ton
of (rate & 0x7f) everywhere.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... by removing an ill-conceived, useless line. Discovered by coverity.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Actually, this patch removev wlan_dev_t totally and puts the used variables
of it directly into wlan_private. That reduces one level of indirection and
looks a little bit simpler. It's now "priv->card" and not
"priv->wlan_dev.card" and "priv->dev" instead of "priv->wlan_dev.netdev"
Changed two occurences of "((wlan_private *) dev->priv)->wlan_dev.netdev"
into "dev", because I didn't see the point in doing pointer-ping-pong.
The variables "ioport", "upld_rcv" and "upld_type" where unused. They have
been removed.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* add CONFIG_LIBERTAS to Kconfig
* remove global variable libertas_fw_name, the USB module might want to
use a different default FW name than the CF module, so libertas_fw_name
is now local to if_usb.c
* exported some symbols as GPL
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patches adds the two functions wlan_add_mesh() and wlan_remove_mesh(),
which are responsible for the mshX interface. In a CF driver with a non-
mesh-aware firmware you can omit the calls to this functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug output of libertas was either not present or it was overwhelming.
This patch adds the possibility to specify a bitmask for the area of
interest. One should then only get the desired output.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb could have been freed by then. Also, in libertas_upload_rx_packet(),
skb->protocol is initialized by eth_type_trans().
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In libertas_process_rxed_packet() and process_rxed_802_11_packet() the
skb is dereferenced after being passed to netif_rx (called from
libertas_upload_rx_packet). Spotted by Coverity (1658, 1659).
Also, libertas_upload_rx_packet() unconditionally returns 0 so the error
check is dead code - might as well take it out and change the signature.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the Marvell Libertas 8388 802.11 USB driver.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
