Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
The GAP Specification gives the flexibility to decide whether MITM
Protection is requested or not (Bluetooth Core Specification v4.0
Volume 3, part C, section 6.5.3) when replying to an
HCI_EV_IO_CAPA_REQUEST event.
The recommendation is *not* to set this flag "unless the security
policy of an available local service requires MITM Protection"
(regardless of the bonding type). However, the kernel doesn't
necessarily have this information and therefore the safest choice is
to always use MITM Protection, also for General Bonding.
This patch changes the behavior for the General Bonding initiator
role, always requesting MITM Protection even if no high security level
is used. Depending on the remote capabilities, the protection might
not be actually used, and we will accept this locally unless of course
a high security level was originally required.
Note that this was already done for Dedicated Bonding. No-Bonding is
left unmodified because MITM Protection is normally not desired in
these cases.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When responding to a remotely-initiated pairing procedure, a MITM
protected SSP associaton model can be used for pairing if both local
and remote IO capabilities are set to something other than
NoInputNoOutput, regardless of the bonding type (Dedicated or
General).
This was already done for Dedicated Bonding but this patch proposes to
use the same policy for General Bonding as well.
The GAP Specification gives the flexibility to decide whether MITM
Protection is used ot not (Bluetooth Core Specification v4.0 Volume 3,
part C, section 6.5.3).
Note however that the recommendation is *not* to set this flag "unless
the security policy of an available local service requires MITM
Protection" (for both Dedicated and General Bonding). However, as we are
already requiring MITM for Dedicated Bonding, we will follow this
behaviour also for General Bonding.
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Do not always set the MITM protection requirement by default in the
field conn->auth_type, since this will be added later in
hci_io_capa_request_evt(), as part of the requirements specified in
HCI_OP_IO_CAPABILITY_REPLY.
This avoids a hackish exception for the auto-reject case, but doesn't
change the behavior of the code at all.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Refactor the code without changing its behavior by handling the
no-bonding cases first followed by General Bonding.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
Pull HID updates from Jiri Kosina:
- substantial cleanup of the generic and transport layers, in the
direction of an ultimate goal of making struct hid_device completely
transport independent, by Benjamin Tissoires
- cp2112 driver from David Barksdale
- a lot of fixes and new hardware support (Dualshock 4) to hid-sony
driver, by Frank Praznik
- support for Win 8.1 multitouch protocol by Andrew Duggan
- other smaller fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (75 commits)
HID: sony: fix force feedback mismerge
HID: sony: Set the quriks flag for Bluetooth controllers
HID: sony: Fix Sixaxis cable state detection
HID: uhid: Add UHID_CREATE2 + UHID_INPUT2
HID: hyperv: fix _raw_request() prototype
HID: hyperv: Implement a stub raw_request() entry point
HID: hid-sensor-hub: fix sleeping function called from invalid context
HID: multitouch: add support for Win 8.1 multitouch touchpads
HID: remove hid_output_raw_report transport implementations
HID: sony: do not rely on hid_output_raw_report
HID: cp2112: remove the last hid_output_raw_report() call
HID: cp2112: remove various hid_out_raw_report calls
HID: multitouch: add support of other generic collections in hid-mt
HID: multitouch: remove pen special handling
HID: multitouch: remove registered devices with default behavior
HID: hidp: Add a comment that some devices depend on the current behavior of uniq
HID: sony: Prevent duplicate controller connections.
HID: sony: Perform a boundry check on the sixaxis battery level index.
HID: sony: Fix work queue issues
HID: sony: Fix multi-line comment styling
...
When sending out a device found event caused by an advertising report in
the situation where we couldn't store the report as a pending one, the
code was incorrectly trying to use the address and address type from the
pending data. Since the pending data is cleared in the previous line
this causes a potentially incorrect address type and an address of
BDADDR_ANY. This patch fixes the call to use the address information
correctly from the received advertising report.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be consistent, lets use msec for this timeout as well.
Note: This define value is a minimum scan time taken from BT Core spec 4.0,
Vol 3, Part C, chapter 9.2.6
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this patch it is possible to control discovery interleaved
timeout value from debugfs.
It is for fine tuning of this timeout.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Keep msec instead of jiffies in this define. This is needed by following
patch where we want this timeout to be exposed in debugfs.
Note: Value of this timeout comes from recommendation in BT Core Spec.4.0,
Vol 3, Part C, chapter 13.2.1.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ssp parameter is supposed to be a mandatory one and there are no
callers that would pass NULL to this function. Removing this unnecessary
NULL check also makes (false positive) static analyzer warnings go away.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When sending a pending device found event triggered by disabling LE
scanning we should use the stored RSSI instead of sending a zero value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Especially in crowded environments it can become frequent that we have
to send out whatever pending event there is stored. Since user space
has its own filtering of small RSSI changes sending a 0 value will
essentially force user space to wake up the higher layers (e.g. over
D-Bus) even though the RSSI didn't actually change more than the
threshold value.
This patch adds storing also of the RSSI for pending advertising reports
so that we report an as accurate RSSI as possible when we have to send
out the stored information to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Occasionally, during active scanning we will receive duplicate ADV_IND
reports from the same device before receiving the SCAN_RSP from them. In
order to not wake up user space unnecessarily it's better not to send
these extra events as they do not contain any new information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The line was incorrectly split between the variable type and its name.
This patch fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All callers of hci_inquiry_cache_update() pass a non-NULL ssp pointer to
it and even the function itself assumes in another place that the
pointer is non-NULL. Therefore, remove the redundant check.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To avoid too many events being sent to user space and to help parsing of
all available remote device data it makes sense for us to wait for the
scan response and send a single merged Device Found event to user space.
This patch adds a few new variables to hci_dev to track the last
received ADV_IND/ADV_SCAN_IND, i.e. those which will cause a SCAN_REQ to
be send in the case of active scanning. When the SCAN_RSP is received
the pending data is passed together with the SCAN_RSP to the
mgmt_device_found function which takes care of merging them into a
single Device Found event.
We also need a bit of extra logic to handle situations where we don't
receive a SCAN_RSP after caching some data. In such a scenario we simply
have to send out the pending data as it is and then operate on the new
report as if there was no pending data.
We also need to send out any pending data when scanning stops as
well as ensure that the storage is empty at the start of a new active
scanning session. These both cases are covered by the update to the
hci_cc_le_set_scan_enable function in this patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're in peripheral mode (HCI_ADVERTISING flag is set) the most
natural mapping of connect() is to perform directed advertising to the
peer device.
This patch does the necessary changes to enable directed advertising and
keeps the hci_conn state as BT_CONNECT in a similar way as is done for
central or BR/EDR connection initiation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation for being able to merge ADV_IND/ADV_SCAN_IND and SCAN_RSP
together into a single device found event add a second parameter to the
mgmt_device_found function. For now all callers pass NULL as this
parameters since we don't yet have storing of the last received
advertising report.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Passive LE scanning is only used by the kernel-internal connection
establishment procedure. It makes therefore little sense to send device
found events to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a timeout occurs using directed advertising a 0x3c error gets
generated. Since the operation is analogous to conventional connection
creation map this to the usual EHOSTDOWN error.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once directed advertising is brought into the picture simply the lack of
an hci_conn object when an le_conn_complete event occurs is no longer a
reliable indication that the responder & initiator values need to be
set based on our advertising address type.
This patch moves the code for setting these values outside of the
"if (!conn)" branch and ensures that they get set for any connection
where we are in the slave role.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Any time hci_conn_add is used for an LE connection we need to ensure
that the local identity address is correctly described in the src and
src_type variables. This patch moves setting these values directly into
hci_conn_add so that callers don't have to duplicate the effort
themselves.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch does a small code simplification replacing the tipical
kmalloc-copy_from_user sequence by memdup_user() helper.
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As preparation for merging ADV_IND/ADV_SCAN_IND and SCAN_RSP together
into a single mgmt Device Found event refactor individual advertising
report handling into a separate function. This will help keep the code
more readable as more logic gets added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should let user space request the peer address also in the pending
connect states, i.e. BT_CONNECT and BT_CONNECT2. There is existing user
space code that tries to do this and will fail without extending the set
of allowed states for the peer address information.
This patch adds the two states to the allowed ones in the L2CAP and
RFCOMM sock_getname functions, thereby preventing ENOTCONN from being
returned.
Reported-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The smp variable in smp_conn_security is not used anywhere before the
smp = smp_chan_create() call in the smp_conn_security function so it
makes no sense to assign any other value to it before that.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The smp pointer might not be initialized for jumps to the "done" label
in the smp_conn_security function. Furthermore doing the set_bit after
done might "overwrite" a previous value of the flag in case pairing was
already in progress. This patch moves the call to set_bit before the
label so that it is only done for a newly created smp context (as
returned by smp_chan_create).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Due to several devices being unable to handle this procedure reliably
(resulting in forced disconnections before pairing completes) it's
better to remove it altogether.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the case that the just-works model would be triggered we only want to
confirm remotely initiated pairings (i.e. those triggered by a Security
Request or Pairing Request). This patch adds the necessary check to the
tk_request function to fall back to the JUST_WORKS method in the case of
a locally initiated pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For remotely initiated just-works pairings we want to show the user a
confirmation dialog for the pairing. However, we can only know which
side was the initiator by tracking which side sends the first Security
Request or Pairing Request PDU. This patch adds a new SMP flag to
indicate whether our side was the initiator for the pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the case that a local pairing confirmation (JUST_CFM) has been
selected as the method we need to use the user confirm request mgmt
event for it with the confirm_hint set to 1 (to indicate confirmation
without any specific passkey value). Without this (if passkey_notify was
used) the pairing would never proceed. This patch adds the necessary
call to mgmt_user_confirm_request in this scenario.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It is possible that the HCI_LE_Start_Encryption command fails in an
early stage and triggers a command status event with the failure code.
In such a case we need to properly notify the hci_conn object and
cleanly bring the connection down. This patch adds the missing command
status handler for this HCI command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LE scan type paramter defines if active scanning or passive scanning
is in use. Track the currently set value so it can be used for decision
making from other pieces in the core.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We need to ensure that we do not send events to user space with the
identity address if we have not yet notified user space of the IRK. The
code was previously trying to handle this for the mgmt_pair_device
response (which worked well enough) but this is not the only connection
related event that might be sent to user space before pairing is
successful: another important event is Device Disconnected.
The issue can actually be solved more simply than the solution
previously used for mgmt_pair_device. Since we do have the identity
address tracked as part of the remote IRK struct we can just copy it
over from there to the hci_conn struct once we've for real sent the mgmt
event for the new IRK.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The passkey_notify and user_confirm functions in mgmt.c were expecting
different endianess for the passkey, leading to a big endian bug and
sparse warning in recently added SMP code. This patch converts both
functions to expect host endianess and do the conversion to little
endian only when assigning to the mgmt event struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In Secure Connections Only mode, it is required that Secure Connections
is used for pairing and that the link key is encrypted with AES-CCM using
a P-256 authenticated combination key. If this is not the case, then new
connection shall be refused or existing connections shall be dropped.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is possible that pairing fails after we've already received remote
identity information. One example of such a situation is when
re-encryption using the LTK fails. In this case the hci_conn object has
already been updated with the identity address but user space does not
yet know about it (since we didn't notify it of the new IRK yet).
To ensure user space doesn't get a Pair Device command response with an
unknown address always use the same address in the response as was used
for the original command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When performing SMP pairing with MITM protection one side needs to
enter the passkey while the other side displays to the user what needs
to be entered. Nowhere in the SMP specification does it say that the
displaying side needs to any kind of confirmation of the passkey, even
though a code comment in smp.c implies this.
This patch removes the misleading comment and converts the code to use
the passkey notification mgmt event instead of the passkey confirmation
mgmt event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some cases the current 250ms delay is not enough for the remote to
receive the keys, as can be witnessed by the following log:
> ACL Data RX: Handle 64 flags 0x02 dlen 21 [hci1] 231.414217
SMP: Signing Information (0x0a) len 16
Signature key: 555bb66b7ab3abc9d5c287c97fe6eb29
< ACL Data TX: Handle 64 flags 0x00 dlen 21 [hci1] 231.414414
SMP: Encryption Information (0x06) len 16
Long term key: 2a7cdc233c9a4b1f3ed31dd9843fea29
< ACL Data TX: Handle 64 flags 0x00 dlen 15 [hci1] 231.414466
SMP: Master Identification (0x07) len 10
EDIV: 0xeccc
Rand: 0x322e0ef50bd9308a
< ACL Data TX: Handle 64 flags 0x00 dlen 21 [hci1] 231.414505
SMP: Signing Information (0x0a) len 16
Signature key: bbda1b2076e2325aa66fbcdd5388f745
> HCI Event: Number of Completed Packets (0x13) plen 5 [hci1] 231.483130
Num handles: 1
Handle: 64
Count: 2
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28 [hci1] 231.664211
Handle: 64
Random number: 0x5052ad2b75fed54b
Encrypted diversifier: 0xb7c2
Long term key: a336ede66711b49a84bde9b41426692e
> HCI Event: Command Status (0x0f) plen 4 [hci1] 231.666937
LE Start Encryption (0x08|0x0019) ncmd 1
Status: Success (0x00)
> HCI Event: Number of Completed Packets (0x13) plen 5 [hci1] 231.712646
Num handles: 1
Handle: 64
Count: 1
> HCI Event: Disconnect Complete (0x05) plen 4 [hci1] 232.562587
Status: Success (0x00)
Handle: 64
Reason: Remote User Terminated Connection (0x13)
As can be seen, the last key (Signing Information) is sent at 231.414505
but the completed packets event for it comes only at 231.712646,
i.e. roughly 298ms later.
To have a better margin of error this patch increases the delay to
500ms.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is a trivial coding style simplification by instead of having an
extra early return to instead revert the if condition and do the single
needed queue_work() call there.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The pairing process initiated through mgmt sets the conn->auth_type
value regardless of BR/EDR or LE pairing. This value will contain the
MITM flag if the local IO capability allows it. When sending the SMP
pairing request we should check the value and ensure that the MITM bit
gets correctly set in the bonding flags.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMP specification is written with the assumption that both key
information, plaintextData and encryptedData follow the same little
endian byte ordering as the rest of SMP.
Since the kernel crypto routines expect big endian data the code has had
to do various byte swapping tricks to make the behavior as expected,
however the swapping has been scattered all around the place.
This patch centralizes the byte order swapping into the smp_e function
by making its public interface match what the other SMP functions expect
as per specification. The benefit is vastly simplified calls to smp_e.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make it possible to (correctly) pass data declared as const as the
src parameter to the swap56 and swap128 functions declare this parameter
also as const.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When performing pairing using SMP the remote may clear any key
distribution bits it wants in its pairing response. We must therefore
update our local variable accordingly, otherwise we might get stuck
waiting for keys that will never come.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Nobody calls hid_output_raw_report anymore, and nobody should.
We can now remove the various implementation in the different
transport drivers and the declarations.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 975508879 "Bluetooth: make bluetooth 6lowpan as an option"
ensures that 6LOWPAN_IPHC is turned on when we have BT_6LOWPAN
enabled in Kconfig, but it allows building the IPHC code as
a loadable module even if the entire Bluetooth stack is built-in,
and that causes a link error.
We can solve that by moving the 'select' statement into CONFIG_BT,
which is a "tristate" option to enforce that 6LOWPAN_IPHC can
only be a module if BT also is a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To avoid flooding the host with useless advertising reports during
background scan, we enable the duplicates filter from controller.
However, enabling duplicates filter requires a small change in
background scan routine in order to fix the following scenario:
1) Background scan is running.
2) A device disconnects and starts advertising.
3) Before host gets the disconnect event, the advertising is reported
to host. Since there is no pending LE connection at that time,
nothing happens.
4) Host gets the disconnection event and adds a pending connection.
5) No advertising is reported (since controller is filtering) and the
connection is never established.
So, to address this scenario, we should always restart background scan
to unsure we don't miss any advertising report (due to duplicates
filter).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently you can have bluetooth 6lowpan without ipv6 enabled. This
doesn't make any sense. With this patch you can disable/enable bluetooth
6lowpan support at compile time.
The current bluetooth 6lowpan implementation doesn't check the return
value of 6lowpan function. Nevertheless I added -EOPNOTSUPP as return value
if 6lowpan bluetooth is disabled.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case the pairable option has been disabled, the pairing procedure
does not create keys for bonding. This means that these generated keys
should not be stored persistently.
For LTK and CSRK this is important to tell userspace to not store these
new keys. They will be available for the lifetime of the device, but
after the next power cycle they should not be used anymore.
Inform userspace to actually store the keys persistently only if both
sides request bonding.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The connection signature resolving key (CSRK) is used for attribute
protocol signed write procedures. This change generates a new local
key during pairing and requests the peer key as well.
Newly generated key and received key will be provided to userspace
using the New Signature Resolving Key management event.
The Master CSRK can be used for verification of remote signed write
PDUs and the Slave CSRK can be used for sending signed write PDUs
to the remote device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
vtable's method alloc_skb() needs to return a ERR_PTR in case of err and
not a NULL.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The debug logs for reporting a discrepancy between the expected amount
of keys and the actually received amount of keys got these value mixed
up. This patch fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This header is used by bluetooth and ieee802154 branch. This patch
move this header to the include/net directory to avoid a use of a
relative path in include.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes authentication failure on LE link re-connection when
BlueZ acts as slave (peripheral). LTK is removed from the internal list
after its first use causing PIN or Key missing reply when re-connecting
the link. The LE Long Term Key Request event indicates that the master
is attempting to encrypt or re-encrypt the link.
Pre-condition: BlueZ host paired and running as slave.
How to reproduce(master):
1) Establish an ACL LE encrypted link
2) Disconnect the link
3) Try to re-establish the ACL LE encrypted link (fails)
> HCI Event: LE Meta Event (0x3e) plen 19
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 64
Role: Slave (0x01)
...
@ Device Connected: 00:02:72:DC:29:C9 (1) flags 0x0000
> HCI Event: LE Meta Event (0x3e) plen 13
LE Long Term Key Request (0x05)
Handle: 64
Random number: 875be18439d9aa37
Encryption diversifier: 0x76ed
< HCI Command: LE Long Term Key Request Reply (0x08|0x001a) plen 18
Handle: 64
Long term key: 2aa531db2fce9f00a0569c7d23d17409
> HCI Event: Command Complete (0x0e) plen 6
LE Long Term Key Request Reply (0x08|0x001a) ncmd 1
Status: Success (0x00)
Handle: 64
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 64
Encryption: Enabled with AES-CCM (0x01)
...
@ Device Disconnected: 00:02:72:DC:29:C9 (1) reason 3
< HCI Command: LE Set Advertise Enable (0x08|0x000a) plen 1
Advertising: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertise Enable (0x08|0x000a) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 64
Role: Slave (0x01)
...
@ Device Connected: 00:02:72:DC:29:C9 (1) flags 0x0000
> HCI Event: LE Meta Event (0x3e) plen 13
LE Long Term Key Request (0x05)
Handle: 64
Random number: 875be18439d9aa37
Encryption diversifier: 0x76ed
< HCI Command: LE Long Term Key Request Neg Reply (0x08|0x001b) plen 2
Handle: 64
> HCI Event: Command Complete (0x0e) plen 6
LE Long Term Key Request Neg Reply (0x08|0x001b) ncmd 1
Status: Success (0x00)
Handle: 64
> HCI Event: Disconnect Complete (0x05) plen 4
Status: Success (0x00)
Handle: 64
Reason: Authentication Failure (0x05)
@ Device Disconnected: 00:02:72:DC:29:C9 (1) reason 0
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The stop_scan_complete function was used as an intermediate step before
doing the actual connection creation. Since we're using hci_request
there's no reason to have this extra function around, i.e. we can simply
put both HCI commands into the same request.
The single task that the intermediate function had, i.e. indicating
discovery as stopped is now taken care of by a new
HCI_LE_SCAN_INTERRUPTED flag which allows us to do the discovery state
update when the stop scan command completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The discovery process has a timer for disabling scanning, however
scanning might be disabled through other means too like the auto-connect
process. We should therefore ensure that the timer is never active
after sending a HCI command to disable scanning.
There was some existing code in stop_scan_complete trying to avoid the
timer when a connect request interrupts a discovery procedure, but the
other way around was not covered. This patch covers both scenarios by
canceling the timer as soon as we get a successful command complete for
the disabling HCI command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some devices may refuse to re-encrypt with the LTK if they haven't
received all our keys yet. This patch adds a 250ms delay before
attempting re-encryption with the LTK.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It's not strictly speaking required to re-encrypt a link once we receive
an LTK since the connection is already encrypted with the STK. However,
re-encrypting with the LTK allows us to verify that we've received an
LTK that actually works.
This patch updates the SMP code to request encrypting with the LTK in
case we're in master role and waits until the key refresh complete event
before notifying user space of the distributed keys.
A new flag is also added for the SMP context to ensure that we
re-encryption only once in case of multiple calls to smp_distribute_keys.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LE connection attempts do not have a controller side timeout in the same
way as BR/EDR has (in form of the page timeout). Since we always do
scanning before initiating connections the attempts are always expected
to succeed in some reasonable time.
This patch adds a timer which forces a cancellation of the connection
attempt within 20 seconds if it has not been successful by then. This
way we e.g. ensure that mgmt_pair_device times out eventually and gives
an error response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that we have nicely tracked values of the initiator and responder
address information we can pass that directly to the smp_c1 function
without worrying e.g. about who initiated the connection. This patch
updates the two places in smp.c to use the new variables.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For SMP we need the local and remote addresses (and their types) that
were used to establish the connection. These may be different from the
Identity Addresses or even the current RPA. To guarantee that we have
this information available and it is correct track these values
separately from the very beginning of the connection.
For outgoing connections we set the values as soon as we get a
successful command status for HCI_LE_Create_Connection (for which the
patch adds a command status handler function) and for incoming
connections as soon as we get a LE Connection Complete HCI event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We shouldn't update the hci_conn state to BT_CONNECT until the moment
that we're ready to send the initiating HCI command for it. If the
connection has the BT_CONNECT state too early the code responsible for
updating the local random address may incorrectly think there's a
pending connection in progress and refuse to update the address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Different controllers behave differently when HCI_Set_Random_Address is
called while they are advertising or have a HCI_LE_Create_Connection in
progress. Some take the newly written address into use for the pending
operation while others use the random address that we had at the time
that the operation started.
Due to this undefined behavior and for the fact that we want to reliably
determine the initiator address of all connections for the sake of SMP
it's best to simply prevent the random address update if we have these
problematic operations in progress.
This patch adds a set_random_addr() helper function for the use of
hci_update_random_address which contains the necessary checks for
advertising and ongoing LE connections.
One extra thing we need to do is to clear the HCI_ADVERTISING flag in
the enable_advertising() function before sending any commands. Since
re-enabling advertising happens by calling first disable_advertising()
and then enable_advertising() all while having the HCI_ADVERTISING flag
set. Clearing the flag lets the set_random_addr() function know that
it's safe to write a new address at least as far as advertising is
concerned.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If SMP fails we should not leave any keys (LTKs or IRKs) hanging around
the internal lists. This patch adds the necessary code to
smp_chan_destroy to remove any keys we may have in case of pairing
failure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The random numbers in Bluetooth Low Energy are 64-bit numbers and should
also be little endian since the HCI specification is little endian.
Change the whole Low Energy pairing to use __le64 instead of a byte
array.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If some of the cleanup commands caused by mgmt_set_powered(off) never
complete we should still force the adapter to be powered down. This is
rather easy to do since hdev->power_off is already a delayed work
struct. This patch schedules this delayed work if at least one HCI
command was sent by the cleanup procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off and disconnecting devices we should also consider
connections which have not yet reached the BT_CONNECTED state. They may
not have a valid handle yet and simply sending a HCI_Disconnect will not
work.
This patch updates the code to either disconnect, cancel connection
creation or reject incoming connection creation based on the current
conn->state value as well as the link type in question.
When the power off procedure results in canceling connection attempts
instead of disconnecting connections we get a connection failed event
instead of a disconnection event. Therefore, we also need to have extra
code in the mgmt_connect_failed function to check if we should proceed
with the power off or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the LE white list gets changed via HCI commands make sure that
the internal storage of the white list entries gets updated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current LE white list entries require storing in the HCI controller
structure. So provide a storage and access functions for it. In addition
export the current list via debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When starting up a controller make sure that all LE white list entries
are cleared. Normally the HCI Reset takes care of this. This is just
in case no HCI Reset has been executed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_blacklist_clear function is not used outside of hci_core.c and
can be made static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The number of places needing the local Identity Address are starting to
grow so it's better to have a single place for the logic of determining
it. This patch adds a convenience function for getting the Identity
Address and updates the two current places needing this to use it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To know the real source address for incoming connections (needed e.g.
for SMP) we should store the own_address_type parameter that was used
for the last HCI_LE_Write_Advertising_Parameters command. This patch
adds a proper command complete handler for the command and stores the
address type in a new adv_addr_type variable in the hci_dev struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to mgmt-api.txt, in case of confirm name command,
cmd_complete should be always use as a response. Not command status
as it is now for failures.
Using command complete on failure is actually better as client might
be interested in device address for which confirm name failed.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If new scanning parameters are set while background scan is running,
we should restart background scanning so these parameters are updated.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patches creates the public hci_req_add_le_passive_scan helper so
it can be re-used outside hci_core.c in the next patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds to debugfs the le_auto_conn file. This file will be
used to test LE auto connection infrastructure.
This file accept writes in the following format:
"add <address> <address_type> [auto_connect]"
"del <address> <address_type>"
"clr"
The <address type> values are:
* 0 for public address
* 1 for random address
The [auto_connect] values are (for more details see struct hci_
conn_params):
* 0 for disabled (default)
* 1 for always
* 2 for link loss
So for instance, if you want the kernel autonomously establishes
connections with device AA:BB:CC:DD:EE:FF (public address) every
time the device enters in connectable mode (starts advertising),
you should run the command:
$ echo "add AA:BB:CC:DD:EE:FF 0 1" > /sys/kernel/debug/bluetooth/hci0/le_auto_conn
To delete the connection parameters for that device, run the command:
$ echo "del AA:BB:CC:DD:EE:FF 0" > /sys/kernel/debug/bluetooth/hci0/le_auto_conn
To clear the connection parameters list, run the command:
$ echo "clr" > /sys/kernel/debug/bluetooth/hci0/le_auto_conn
Finally. to get the list of connection parameters configured in kernel,
read the le_auto_conn file:
$ cat /sys/kernel/debug/bluetooth/hci0/le_auto_conn
This file is created only if LE is enabled.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only identity addresses are inserted into hdev->pend_le_conns. So,
in order to support resolvable private addresses in auto connection
mechanism, we should resolve the address before checking for pending
connections.
Thus, this patch adds an extra check in check_pending_le_conn() and
updates 'addr' and 'addr_type' variables before hci_pend_le_conn_
lookup().
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should only accept connection parameters from identity addresses
(public or random static). Thus, we should check the address type
in hci_conn_params_add().
Additionally, since the IRK is removed during unpair, we should also
remove the connection parameters from that device.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hdev is closed (e.g. Mgmt power off command, RFKILL or controller
is reset), the ongoing active connections are silently dropped by the
controller (no Disconnection Complete Event is sent to host). For that
reason, the devices that require HCI_AUTO_CONN_ALWAYS are not added to
hdev->pend_le_conns list and they won't auto connect.
So to fix this issue, during hdev closing, we remove all pending LE
connections. After adapter is powered on, we add a pending LE connection
for each HCI_AUTO_CONN_ALWAYS address.
This way, the auto connection mechanism works propely after a power
off and power on sequence as well as RFKILL block/unblock.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the user sends a mgmt start discovery command while the background
scanning is running, we should temporarily stop it. Once the discovery
finishes, we start the background scanning again.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch modifies hci_conn_params_add() and hci_conn_params_del() so
they also add/delete pending LE connections according to the auto_
connect option. This way, background scan is automatically triggered/
untriggered when connection parameters are added/removed.
For instance, when a new connection parameters with HCI_AUTO_CONN_ALWAYS
option is added and we are not connected to the device, we add a pending
LE connection for that device.
Likewise, when the connection parameters are updated we add or delete
a pending LE connection according to its new auto_connect option.
Finally, when the connection parameter is deleted we also delete the
pending LE connection (if any).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the LE auto connection options: HCI_AUTO_CONN_
ALWAYS and HCI_AUTO_CONN_LINK_LOSS. Their working mechanism are
described as follows:
The HCI_AUTO_CONN_ALWAYS option configures the kernel to always re-
establish the connection, no matter the reason the connection was
terminated. This feature is required by some LE profiles such as
HID over GATT, Health Thermometer and Blood Pressure. These profiles
require the host autonomously connect to the device as soon as it
enters in connectable mode (start advertising) so the device is able
to delivery notifications or indications.
The BT_AUTO_CONN_LINK_LOSS option configures the kernel to re-
establish the connection in case the connection was terminated due
to a link loss. This feature is required by the majority of LE
profiles such as Proximity, Find Me, Cycling Speed and Cadence and
Time.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the LE auto connection infrastructure which
will be used to implement the LE auto connection options.
In summary, the auto connection mechanism works as follows: Once the
first pending LE connection is created, the background scanning is
started. When the target device is found in range, the kernel
autonomously starts the connection attempt. If connection is
established successfully, that pending LE connection is deleted and
the background is stopped.
To achieve that, this patch introduces the hci_update_background_scan()
which controls the background scanning state. This function starts or
stops the background scanning based on the hdev->pend_le_conns list. If
there is no pending LE connection, the background scanning is stopped.
Otherwise, we start the background scanning.
Then, every time a pending LE connection is added we call hci_update_
background_scan() so the background scanning is started (in case it is
not already running). Likewise, every time a pending LE connection is
deleted we call hci_update_background_scan() so the background scanning
is stopped (in case this was the last pending LE connection) or it is
started again (in case we have more pending LE connections). Finally,
we also call hci_update_background_scan() in hci_le_conn_failed() so
the background scan is restarted in case the connection establishment
fails. This way the background scanning keeps running until all pending
LE connection are established.
At this point, resolvable addresses are not support by this
infrastructure. The proper support is added in upcoming patches.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the hdev->pend_le_conn list which holds the
device addresses the kernel should autonomously connect. It also
introduces some helper functions to manipulate the list.
The list and helper functions will be used by the next patch which
implements the LE auto connection infrastructure.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves address type conversion (L2CAP address type to HCI
address type) to outside hci_connect_le. This way, we avoid back and
forth address type conversion in a comming patch.
So hci_connect_le() now expects 'dst_type' parameter in HCI address
type convention.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_connect() is a very simple and useless wrapper of hci_connect_acl
and hci_connect_le functions. Addtionally, all places where hci_connect
is called the link type value is passed explicitly. This way, we can
safely delete hci_connect, declare hci_connect_acl and hci_connect_le
in hci_core.h and call them directly.
No functionality is changed by this patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes hci_create_le_conn() since it is not used anymore.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some LE controllers don't support scanning and creating a connection
at the same time. So we should always stop scanning in order to
establish the connection.
Since we may prematurely stop the discovery procedure in favor of
the connection establishment, we should also cancel hdev->le_scan_
disable delayed work and set the discovery state to DISCOVERY_STOPPED.
This change does a small improvement since it is not mandatory the
user stops scanning before connecting anymore. Moreover, this change
is required by upcoming LE auto connection mechanism in order to work
properly with controllers that don't support background scanning and
connection establishment at the same time.
In future, we might want to do a small optimization by checking if
controller is able to scan and connect at the same time. For now,
we want the simplest approach so we always stop scanning (even if
the controller is able to carry out both operations).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the "hci_" prefix to le_conn_failed() helper and
declares it in hci_core.h so it can be reused in hci_event.c.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
