Since check_firmware is called via analog or digital set freq routines, move
type selection to those routines. This avoids having several if's at the code,
and simplifies the source code.
A sideback effect is that implementing radio and other dvb types will become
simpler.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move some tv-audio initialization code out of tvaudio thread,
and call it on resume too.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First the saa7134_initdev waits between saa7134_hwinit1
and saa7134_hwinit2 , thus it is probably wise to do the same in saa7134_resume
some hardware probably needs this.
Call saa7134_irq_video_signalchange in .resume like in saa7134_resume to make
saa7134_resume mirror perfectly the saa7134_initdev although
this call isn't strictly necessary in the saa7134_initdev,
but it won't harm anyway.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*dev->insuspend = 1 should be set before synchronize_irq
*ACK interrupts after synchronize_irq, to make sure there aren't
pending interrupts.
*Add barrier before we restart interrupts so the handler will 100%
see the dev->insuspend
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pci_save_state should be called before pci_set_power_state
and pci_restore_state after pci_set_power_state
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes a few remainders of the VID_HARDWARE_* removal.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
643d01fb38b6f376cced035549f4e193018776e7
On some cases, xc2028/xc3028 wents into "turn off" mode. It seems that this
happens when very weak signals are tuned. To solve this, specific standard
reaload were done previously. Christopher patches changed this behavior to a
complete firmware reload.
This patch removes the hack. A much cleaner solution for this trouble is just
to sent a xc2028/3028 software reset.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
xc3028 can be used on some DTV only designs (for example, DVB-S boards). Before
this patch, a DTV only board would need to call set_tuner_config callback.
This patch allows to optionally pass a xc3028_ctrl parameter, via xc3028_config
struct, fully initializing the driver for DTV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Xc2028.3028 has two type of firmwares: audio-standard specific ones and
baseband MTS firmwares. MTS firmwares provide stereo decoding for 6 MHz
BTSC/EIAJ and for monoaural audio decoding on 8 MHz firmwares.
It seems that the option to use MTS or a standard-specific audio decoding
depends on the way xc2028/3028 is connected.
Instead of wasting 32 (or 64 bits) to signalize if the driver needs to use MTS
firmware, this patch converts it to a bitfield that can be shared with other
proprieties of xc2028/3028.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some drivers call set_frequency before selecting the video standard. Before
this patch, an invalid standard ID could be assumed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Whilst reanalysing my formulas I realised it was no longer possible to get the
right values for a 36.1667MHz IF due to rounding problems.
Storing frequencies in units of 0.1kHz makes it possible to calculate these
again correctly.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are at least three variants of the DViCO FusionHDTV DVB-T NANO that
share the same USB device ID. The first (ZL10353 w/ firmware in ROM) is
already supported; the latter two both require firmware and have either
an MT352 or ZL10353 demodulator, and have a different IR receiver from the
first.
This introduces a new identify_state that can tell the difference between a
"warm" device which is running the embedded firmware, and a "cold" device
that needs us to upload firmware to it before it will work. We patch the
uploaded device ID (like we do for other bluebird devices) to make it easy
to identify the particular device variant when it reattaches.
NB: These devices use a different firmware file from previous bluebird
devices. You need a new firmware file to make this work.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rework the input frequency calculation so that it produces the right values
when the ADC oversamples the IF input.
This means MT352 devices can now process a near-zero IF (according to the,
specs 4.57MHz is supported with the default crystal).
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the DViCO FusionHDTV DVB-T NANO with zl10353 demodulator and
firmware in ROM on the device.
Again, this is based on the great work of Mike Krufky with my modifications
to use the in-tree XC2028 driver.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When loading init1 firmware, there may not be an 8MHz specific version.
Load the non-8MHz version if it exists.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When searching for standard-specific analog firmware, only certain
type bits are valid, much like for DTV. Mask them off when finding
the firmware to load.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When loading BASE firmware, we must use std = 0.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for DViCO's Dual Digital 4 with xc3028 tuner, zl10353 DVB-T
demodulator and a new-style I2C IR remote control receiver.
This would not have been possible without the work of and advice from
Mike Krufky, who originally got the Dual Digital 4 and second-gen DVB-T
NANO devices working with the out-of-tree XC3028 driver.
I converted it to use the in-tree XC3028 driver (after making it suitable
for our use), and added the IR remote control support based on his advice.
NB: a firmware package is required to use this device.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add sleep method to enable putting the tuner into standby mode.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In practice, the tuner occasionally fails to respond correctly after a
firmware load. Retry the firmware load if the firmware/hardware version
we read back from the tuner after programming does not match what we
expect.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define a list of valid "firmware types" for each combination of BASE,
DTV and SCODEs. By masking the appropriate firmware bits off we can
just use one "type" for the firmware searching and also flag when we
are looking for a BASE, DTV or SCODE type firmware. This makes it
much easier to track if we need to change device modes or flash an
individual firmware part.
Add a structure to remember what firmware properties we have. This
contains the currently loaded/wanted base firmware (type), video std
(id), video std requested (std_req), scode file and number in use.
Incorporate said structure into the tuner private data.
When checking whether the current firmware needs to be reloaded, first
figure out exactly what "type" of firmware we want (base, std and
scode), and then proceed to load the appropriate matching base,
std-specific and scode records iff there are any changes required.
This removes guesswork from the process because we no longer need to
individually code a check for every tuning parameter's interactions.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a bit to select D2633 DTV firmware to struct xc2028_ctrl, so that it can
be enabled via .set_config.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When validating and loading SCODE firmware we need to take into account the
two-byte size header before each entry.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than picking the first video standard firmware that supports any of
the standards that the user has requested, try to select one that supports
as many of them as possible. This improves the likelihood that the firmware
we select will support the user's desired TV standard.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is no need to duplicate the max_len field from the ctrl structure
in the private data. If we use it directly from priv->ctrl, we can memcpy
the structure (apart from strings) to reduce maintenance as it grows.
Enforce a minimum max_len length of 8 data bytes (+ 1 address byte) as seems
to be required by the tuner.
Also, use kstrdup instead of open coding the string duplication.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
7MHz bandwidth DVB-T needs an adjusted offset at the PLL to ensure the IF
output is correctly centered.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We were using priv->bandwidth to select the base firmware to load, not the
requested bandwidth value, oops. Also, 7MHz Digital TV needs 8MHz base
firmware loaded.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The frequency divisor should only be four bytes long. Also, display the
frequency and divisor correctly in the debug output.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hold the private lock over set_config and set priv->firm_size to 0 after a
failed firmware load to prevent firmware accidentally being freed on us.
Clean up the firmware load/error messages somewhat and rename priv->version
to priv->firm_version to make it clear which "version" it is.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add break to stop us from following the default failure path even upon success.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Protect refcount changes and modifications to xc2028_list with a mutex.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cast v4l2_std_id variables to unsigned long long so they will printk properly.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix some missing spaces in errors that may be emitted during attach failure.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Issuing register reads as a separate address write and data read transactions
means that other I2C activity could occur in between and state could get out
of sync. Issue both the write and read in a single transaction so that the
i2c layer can prevent other users accessing the bus until we are complete.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The I2C macros have side effects and send_seq could cause a return from
a function with a mutex held. Change them to behave like real functions.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now we know the zl10353's correct ADC clock, we can calculate the input
frequency registers correctly instead of just blindly setting them.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Issue FSM_GO instead of TUNER_GO if there is no tuner attached to the
secondary i2c bus.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The path to perform a read immediately after a write was not checking that
the address being read from was the same as the one that was written.
Handling this case correctly should mean that we now can handle more than
two i2c messages at a time.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Any i2c read request that was not immediately preceded by a write request was
incorrectly taking the write path. Add the capability to handle individual
read requests.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The i2c master_xfer routine should return a negative result if not all
transfers completed successfully.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Callers to cxusb_ctrl_msg currently do not receive any indication that their
transfer failed. Return the true return code from dvb_usb_generic_{rw,write}.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134-oss is deprecated for quite some time, it's the only remaining OSS
user outside of sound/oss/, and considering how few and what kind of
soundcards are left supported by OSS I hardly see any use cases left.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If tda827x_config hasn't been defined, exit the function.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ability to read Hauppauge eeprom's was recently added to saa7134,
so we must build the tveeprom module.
Thanks to Matthias Schwarzott for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The HVR-900 requires the MTS version of the xc3028 firmware in order
to get any sound. The below patch selects this firmware variant on
HVR-900 cards, as well as splitting the HVR-950 into its own entry
(since I don't know if it uses the MTS variant and it will have to be
split off eventually anyway).
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TM5600/TM6000 needs clock reset during firmware load. This patch adds the
capability of caling a callback method for this.
Also, avoids uneeded firmware loads.
Signed-off-by: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removes uneeded parameters and adds an structure for passing the parameters
This patch is co-authored by Mauro Carvalho Chehab.
Signed-off-by: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Increased size of dev->eedata from 128 to 256, since the Hauppauge data begins
at byte 128. This has been tested on boards with smaller eeproms, and caused
no problems.
Added comments to distinguish between the various versions of the HVR1110.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
While there's no public API to define audio standard, adds a hack option for
select them. This is needed only for NICAM and A2 firmwares, since AM, BTSC and
EAIJ are already properly handled, on firmware version 2.7.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make the driver less verbose by default. It adds a debug parameter to make the
driver more verbose.
Also, error messages were using KERN_ERR level, instead of KERN_INFO.
A few printk messages were reviewed to make them more clear.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some tuners, like xc3028, need to print error messages. Instead of declaring
local macros, create a tuner global macro for printing tuner errors.
To preserve CodingStyle on all tuner_macros, a few CodingStyle violations were
fixed at the other macros:
- lines with more than 80 columns
- two statements at the same line
The patch also removes the CodingStyle violation of having emacs declarations
inside de source code (CodingStyle chapter 18).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Xceive 2028/3028 has a concept of scode/dcode.
Scode is a table of 16 values (each with 12 bytes i2c sequence).
Dcode is the entry of Scode table that should be used, given a certain
frequency.
The idea is that, depending on what frequency is selected, and according with a
country-based (or standard-based?) table, the Xceive should be "hacked" to
fine-tune that specific frequency.
By default, Scode=0 is used, for undefined frequencies. Also, Scode=0 seems to
be the most used value.
This patch adds the capability of selecting a scode. However, extra work will
be needed to allow auto-selecting the proper scode, for a given set of
frequencies.
I'm not sure what would be the proper way for implementing the dcode selection.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Firmware version 2.7 has other firmware types. This patch adds the capability
for the driver to work with those newer types.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds a new image sensor to the sn9c102 driver.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add remote controller support for Leadtek Winfast DTV Dongle based on
DiB7700P, MT2060 and using last drivers (6040:6a79c243aecc), firmware
dvb-usb-dib0700-03-pre1.fw
Signed-off-by: Jaroslav Barton <djaara@djaara.net>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the conversion to the vidio_ioctl2, tvnorms array is not required anymore.
Also, removed some code from V4L1 time (VIDEO_MODE_foo), specied at the
non-used video_decoder.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were some vestiges of an old V4L1 I2C driver that were called by em28xx.
This patch removes this dead code, and replaces videodev.h to videodev2.h
Now, this driver doesn't require V4L1 anymore.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Uses the newer ioctl handler at videodev. This patch also cleans up some
bad logic at the driver and do CodingStyle and other cleanups at the
resulting driver.
Also, since VIDIOCMBUF were not working, the V4L1 compat code were removed.
The compat code will eventually be re-inserted, if we find a clean way for
implementing compatibility with the old API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On some situations, closing an streaming application and re-opening were
returning -EBUSY.
Uses the same locking schema also present on cx88.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allows shared access support for em28xx. Just one userspace application is
allowed to get stream. The other(s) application(s) can change V4L2 controls,
set video standards, etc.
This patch were splited from Markus Rechberger's tree and backported to 2.6.17
by Pádraig Brady.
The original patch were ported to the latest em28xx version and had CodingStyle
corrected to solve the issues pointed by scripts/checkpatch.pl.
Thanks to Pádraig Brady <P@draigBrady.com> for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L: Int if: Set slave's master before attach, remove master argument
The master also now gets its own pointer from slave's structure.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes some needlessly global debug variables static.
opera1.h became so small that I removed it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global functions in
et61x251_core.c static:
- et61x251_read_reg()
- et61x251_i2c_try_read()
- et61x251_i2c_try_write()
- et61x251_i2c_read()
- et61x251_i2c_write()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global functions static:
- cx8802_init_common()
- cx8802_fini_common()
- cx8802_suspend_common()
- cx8802_resume_common()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes the unused EXPORT_SYMBOL(flexcop_reset_block_300).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following cleanups:
- make the needlessly global vp702x_usb_out_op() static
- #if 0 the unused vp702x_power_ctrl()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Trent Piepho for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hauppauge firmwares can be decoded using tveeprom. This patch adds HVR-900 as
a tveeprom client. It also adds xc3028 tuner entry to tveeprom.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The status registers require a dword for setting register. Fix it on all
occurrences, and at xc3028_get_reg. Also, improves the hardware/firmware
detection printk.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default_mode_mask global is replaced by a list of tuner structs. The
tuner driver now walks that list to see which radio and/or tv tuner
devices are registered to a given i2c adapter.
The default_mode_mask global had to go since this is no longer supported
with the new bus-based I2C API.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To ensure prevention of detecting a tda9885/6/7 as a tda8290 or tda8295, we
will rule out the tda988x before testing the tda8290 / tda8295 id registers.
We read 8 bytes from the chip. If they are all equal, then it is not a
tda829x, or some other error has occurred.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
From: Mauro Carvalho Chehab <mchehab@infradead.org>
In file included from drivers/media/video/em28xx/em28xx-i2c.c:31:
drivers/media/video/tuner-xc2028.h:10:26: error: dvb_frontend.h: No such file or directory
In file included from drivers/media/video/em28xx/em28xx-i2c.c:31:
drivers/media/video/tuner-xc2028.h:32: warning: 'struct dvb_frontend' declared inside parameter list
drivers/media/video/tuner-xc2028.h:32: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
From: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/tda8290.c:27:21: error: tda827x.h: No such file or directory
drivers/media/video/tda8290.c:28:22: error: tda18271.h: No such file or directory
drivers/media/video/tda8290.c:52: error: field 'cfg' has incomplete type
drivers/media/video/tda8290.c: In function 'tda829x_find_tuner':
drivers/media/video/tda8290.c:590: error: implicit declaration of function 'tda18271_attach'
drivers/media/video/tda8290.c:598: error: implicit declaration of function 'tda827x_attach'
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds autodetection support for the Cinergy200 USB and the VGear PocketTV.
Whenever a usb device with generic empia em2800 usb ids is detected the device
gets scanned for connected i2c devices. If the device list matches an em2800
device in the device list the model id gets changed accordingly.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Prevent the tda8295 from falsely being detected as a tda9887
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
attached patch adds support for the vgear pockettv.
It seems to require a write to another register for audio to work.
I checked my old cinergydrv and we did the same register write there. I
therefore enabled it for all em2800 based devices.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch modifies the em28xx driver so that there can be ioctls from
multiple different threads.
This is necessary for capture apps like MPlayer that use different threads for
capturing and channel tuning.
Now the locking is only done for the ioctls that change properties of the
device or access the i2c bus.
It also removes some locks that look unnecessary:
In em28xx_init_dev:
the videodevice is not registered yet so nothing can access the hardware
meanwhile, the device struct is not assigned to the interface yet so no race
with disconnect is possible
In em28xx_release_resources:
it gets only called when dev->lock is already held
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a function to allow trying to detect boards that shares
the generic IDs.
The current detection method is based at eeprom checksum.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ttpci Kconfig file has bugs that cause it to fail in certain Kconfig
situations. The basic problem is that it selects certain drivers, but does
not depend on the dependencies of those drivers.
See http://article.gmane.org/gmane.comp.video.video4linux/35072
Using the Kconfig file also has some annoyances. For instance one can't turn
off AV7110 support unless you go down several options and first turn off
budget-patch support. Normally user selectable drivers are not forced on like
this.
The "AV7110 cards with Budget Patch" option is disabled if "Budget cards"
isn't on. Normally a driver appears nested under a driver it depends on, but
since drivers that don't depend on "Budget cards" are between the two options,
the config programs can't display the tree correctly.
The Makefile has an issue too. Some modules, ttpci-eeprom and budget-core,
appear in the Makefile under several different config symbols. If more than
one of these symbols is on, they will get added the to list of objects
multiple times. The normal convention is to have a config symbol just the
common object(s) and have the users of the that object either depend on or
select that config symbol.
This patch fixes all these issues. ttpci-eepom is under a new config symbol,
and so is the budget-core module. The four different budget card types appear
as sub-drivers under a main "SAA7146 DVB cards" option. Turning on
budget-patch doesn't force AV7110. Drivers using SAA7146_VV have the
necessary VIDEO_DEV dependency, so that it isn't possible to select SAA7146_VV
without V4L being on.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Someone wasn't using the v4l-dvb commit scripts and so didn't run the
automatic whitespace cleaner on their code.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Alter the tuner_foo printk macros to indicate which module is
generating the message.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner sub-module will usually log its type during its _attach() function,
then tuner-core reports which type was attached when control is returned.
In most cases, we expect to see the same message reported from both locations.
We only need to see this second message if debug is enabled.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver is used by the ASUS Falcon2 cx23416-based cards.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several media drivers use input_(*) functions so they need to depend on
the INPUT config symbol.
drivers/built-in.o: In function `bttv_input_fini':
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:346: undefined reference to `input_unregister_device'
drivers/built-in.o: In function `bttv_input_init':
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:204: undefined reference to `input_allocate_device'
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:335: undefined reference to `input_free_device'
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:321: undefined reference to `input_register_device'
linux-2.6.24-rc1-git4/drivers/media/video/bt8xx/bttv-input.c:335: undefined reference to `input_free_device'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Most of the driver were written by Mauro Carvalho Chehab.
DTV parts were added by Michel Ludwig.
Reviewed-by: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds USB ID for HVR-950. It also adds the callback for handling
firmware loading.
Thanks to Markus Reichberger for the reset commands.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- priv->count were wrong. Should be incremented since the first usage;
- forgot to use list_del() to remove the driver;
- Release memory if an error occurs during _attach
Thanks to Aidan Thornton <makosoft@googlemail.com> for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I2C bus redesign changed i2c parameters. This patch re-adds tuner xc2028
attach function, replacing the parameters to the newer syntax.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bus-based I2C subsystem allocates the i2c_client struct. So if in order to
be able to convert the tuner to the bus-based I2C API the embedded i2c_client
struct must be removed from the tuner struct and replaced with a pointer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The next patchset series will change i2c structs inside tuner. This patch
avoids breaking bissect, by commenting the still unused tuner xc2028.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TUNER_PHILIPS_TDA8290 will autodetect a TDA8290 or a TDA8295,
so we don't need this separate entry anymore.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Consolidate tda8290_attach() and tda8295_attach() into a single function,
tda829x_attach(), which will detect chip combinations tda8290 or tda8295 with
tda8275, tda8275a or tda18271.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the chip isn't recognized, then the correct errors should be returned.
The v4l2_i2c_attach() utility function will return 0 for all errors
except -ENOMEM to provide proper compatibility support for the old I2C
probing function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Two new headers were added: one for I2C drivers that are only used
by V4L2 drivers converted to the new bus-based I2C API, and one that
can be used by both converted and unconverted drivers (at the expense of
some additional overhead).
To support the legacy I2C API a helper function was added to v4l2-common.c.
These headers take care of all the 'boilerplate' code that all V4L2 I2C drivers
have in common and will automatically support the bus-based I2C API introduced
in kernel 2.6.22.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This module was always GPL, and will remain GPL
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Call analog_demod_ops->i2c_gate_ctrl when in analog tuning mode, and
frontend_ops.i2c_gate_ctrl when in digital tuning mode.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In some designs, the tuner silicon may be on an i2c bus behind an i2c gate,
controlled by the analog demodulator. We already have a method to control
such i2c gates when they are controlled by the digital demodulator, but in
some hybrid designs, there may be an i2c gate controlled by each demodulator.
For example, when in analog tuning mode, one would access the tuner by opening
the i2c gate controlled by the analog demodulator, while when in digital
tuning mode, one would access the tuner by opening the i2c gate controlled by
the digital demodulator.
We must add this callback function to analog_tuner_ops in order to handle
such configurations.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Explain who is responsible for freeing analog_demod_priv
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert tda9887 and tda8290/5 to dvb_frontend interface
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clear analog_demod_ops on release.
Fix test for analog_demod_ops after tuner attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add basic support for NXP TDA8295 analog demod and TDA18271 tuner silicon.
TDA8295 + TDA8275a not yet tested.
TDA8290 + TDA18271 not yet supported.
Digital mode of TDA18271 not yet tested & needs more work.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
EXPORT_SYMBOL should have been EXPORT_SYMBOL_GPL
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add analog tuning support to tda827x dvb_frontend tuner module.
Convert tda8290 module back to native tuner interface.
The tda8290 analog demodulator will be handled the same way as tda9887.
The tuner.ko module (tuner-core) will pass commands to tda8290 via the
tuner_operations interface. tda8290 will communicate with tda827x via
the dvb_frontend interface, while passing a pointer to a private data
structure.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changeset converts tuner-xc2028 to the newer hybrid approach. It also
prevents creating twice the xc3028 private struct by both DVB and V4L parts.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also replaces all occurrences of TUNER_XCEIVE_XC3028 to TUNER_XC2028.
Some work is still may be required to make sure that non-tm6000 drivers will
be capable of using tuner-xc2028.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L1 ioctls were replaced to V4L2 were applicable. The older ones
already implemented were removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is part of the old V4L1->V4L2 bttv patch, ported to current tree
by Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is part of the old V4L1->V4L2 bttv patch, ported to current tree
by Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is part of the old V4L1->V4L2 bttv patch, ported to current tree
by Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134_buffer_requeue() and set_tvnorm() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This board has some special tea5767 configuration. Basically, radio
XTAL uses a different frequency than the other supported radios. It
uses a 13 MHz XTAL.
This patch adds the proper radio gpio and tea5767 configurations for
the board.
Also, with PAL/BG, the board requires some special init for tda9887:
port1=0 port2=0 qss=1
Thanks to Serge Kolotylo and MIDImaster for their help on identifying
the proper needs for this driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tea5767 has several possible configurations. Before the patch, the
driver were assuming the more common configuration. However, some newer
cards, like MSI @nyware Master requires other configurations, like
de-activating a gpio port and changing chip Xtal.
This patch adds the capability of altering device configuration at
runtime. This may also be used later to activate some features like
auto-mute when signal is weak.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the only tuner-specific device that allows special
configurations is tda9887. However, tea5767 also may require some
special configurations (for example, to specify a different Xtal freq).
This patch replaces TDA9887_SET_CONFIG by a more generic internal ioctl
(TUNER_SET_CONFIG). The newer one allows specifying what tuner is
appliable to a configuration set, and allows an arbitrary configuration
struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correct wrong sized spinlock flags, form int to unsigned long.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix driver data name to match whitelist of acceptable names that contain
pointers init data so that section mismatch warning is placated.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Using an udelay of 5 seems to result in problems for several people.
For now abandon the udelay value of 5 and stick to 10, even though this
will mean a longer load time of the cx2584x firmware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The eeprom decides which Hauppauge model it is, so the decision whether to
use an udelay of 5 or 10 needs to be taken after reading the eeprom, not
before.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
QAM SNR values were incorrect when the cable was disconnected. This
patch extends the lookup tables to ensure correct values are being
returned.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since not all code under drivers/media/video/ depends on
CONFIG_VIDEO_DEV we cannot only enter it depending
on CONFIG_VIDEO_DEV.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Hermann Pitton for noticing that this was missing.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After commit 19fb145799 the callers in
videobuf-core.c that already hold the lock must call
__videobuf_read_start() instead of videobuf_read_start().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf_dvb needs videobuf_read_start. The EXPORT_SYMBOL_GPL() were removed by
a previous patch. However, videobuf_dvb needs this.
This patch re-adds videobuf_read_start, doing the proper lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On Tue, 4 Dec 2007, Ingo Molnar wrote:
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_get_tuner_i2c_master'
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_set_config'
Seems like -common part contains also code that is not completely
common to all the modules.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cxusb needs tuner-xc2028*.h files, but Makefile is not adding its patch
drivers/media/dvb/dvb-usb/cxusb.c:33:26: error: tuner-xc2028.h: File not found
drivers/media/dvb/dvb-usb/cxusb.c:34:32: error: tuner-xc2028-types.h: File not found
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are several months my hvr1110 stop working.
This is very simple to fix, for my card revision at least, by setting a
missing field to the hauppauge_hvr_1110_config.
Signed-off-by: Benoit Istin <beistin@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is pretty serious bug. map->count is never initialized after the
call to kmalloc making the count start at some random trash value. The
end result is leaking videobufs.
Also, fix up the debug statements to print unsigned values.
Pushed to http://ifup.org/hg/v4l-dvb too
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134 video driver starts dropping frames when used together with the
saa7134-alsa driver. Frames are dropped because when an audio event is waiting
the driver simply ignores the interrupt and passes it on to the saa7134-alsa
interrupt handler. The alsa interrupt handler in turn acknowledges all types
of events thus clearing the pending video events as well. Fix by only masking
out the audio event in the video interrupt handler and by only acknowledging
the audio event in the alsa driver.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vmux for composite over s-video input was wrong.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Complement va_start() with va_end() + minor style fixes in the same function.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The period handling in saa7134-alsa is broken in two ways. First, the
minimum number of periods of two does not work, because the dma is setup
two periods ahead in the irq handler. Fix the minimum to four periods.
Second, the code assumes that the number of periods is divisible by two,
which isn't always the case on ALSA. Fix by adding a constraint.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default adc_clock for the zl10353 is different from what was originally
thought to be the case and the TRL nominal rate formula was incorrect as a
result. Use a better (and hopefully now correct) formula.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drivers were using cookie cutter code for stopping the read/stream. Use the
new videobuf_stop function which is lock safe.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add comments to functions that require that caller hold q->lock
- Add __videobuf_mmap_free that doesn't hold q->lock for use within videobuf
- Add locking to videobuf_mmap_free
- Fix linux/drivers/media/common/saa7146_video.c which was holding lock around
videobuf_read_stop
- Add locking to functions that operate on a queue
- Add videobuf_stop to take care of stopping in both the read and stream case
TODO: bttv still has an unsafe call to videobuf_queue_is_busy
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a modified version of a patch previously posted by Thomas
Unverzagt.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch is required so that the autodetecion code also works after
a reboot.
Setting the I2C speed does not seem to be supported for em2800.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver is tearing down its sysfs related pieces in the
incorrect order. This leaves dangling pointers which causes the
kernel device core to oops. The problem has been present virtually
forever but became malignant with the changeover to the way of
handling /sys/class. Fix is just to make sure we don't tear down the
class structure until AFTER the driver instances are deregistered.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
vivi.c is a virtual driver that builds without PCI and should run on
non-pci hardware.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This em28xx-video.c uses functions from this header, but doesn't include it.
It depends on some v4l headers included two levels down including poll.h,
which includes mm.h.
These v4l headers might change, so it's best to include the headers needed
directly.
It also causes problems for the out of core build system's backward
compatibility with older kernels, which is the real reason I bothered to
create a patch for something that would otherwise be so minor that it would
hardly be worth the trouble.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho wrote:
> I do not think the saa7134-alsa driver supports mmap. The cx88-alsa driver
> also claimed to support mmap, but it never worked until I fixed it. It's
> pretty clear that the code in saa7134-alsa was based on the same code as
> cx88-alsa, so it's likely it has the same bug.
You are right. The patch below (based on your cx88 patch, but I don't
really understand it) fixes mmap support in saa7134-alsa for me.
Recording via mmap (arecord -M -f S16_LE -c 2 -r 32000 -D hw:1) didn't
work at all before, works now, tested for at least 20 minutes (but,
unfortunately, with one overrun at least 0.719 ms long).
Signed-off-by: Alexander E. Patrakov <patrakov@ums.usu.ru>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver's sysfs implementation had long since implemented a
dummy hotplug function because at the time the kernel would oops
without at least the empty function being present. Today - after
numerous class interface changes in the kernel - this pvrusb2 change
had been dutifully carried forward but an inspection of the kernel
sources shows that it is no longer needed. So remove the dummy
function and its reference. This also solves a recurring backwards
compatibility issue in the pvrusb2 driver as the class interface has
been getting thrashed in the kernel.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
if(!x & y) should either be if(!(x & y)) or if(!x && y)
I made changes as seemed appropriate, but please review
this is against current git.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes the signal strength value (higher value = higher signal strength)
and scales the value to the range of 0..ffff. The characteristic itself
is wrong. To get proper values on a TT-C2300 in the range of 40..60%
real signal strength, the values from the patch should be divide by two.
The attached patch doesn't fix the characteristic.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix reported signal strength value (higher value = higher signal strength).
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Bit error counting fixed for the tda10021.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the acquisition range for clock recovery from 120 ppm to
240ppm. Apparently, some cable providers in Germany are playing with
their parameters, and the capture range of the ves1820 is too small
to acquire a lock with the current setting... ;-(
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Two fixes for the 'saa7146_wait_for_debi_done' code:
(a) Timeout did not work when the routine was called with
interrupts disabled.
(b) Reduce PCI I/O load caused by saa7146_wait_for_debi_done.
Seems to be very important on fast machines!
Based on code posted by Hartmut Birr @vdr-portal.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All of these drivers select VIDEO_IR, which uses the input subsystem,
so they should also depend on INPUT.
Problem examples:
drivers/built-in.o: In function `ir_input_key_event':
ir-functions.c:(.text+0x10849a): undefined reference to `input_event'
ir-functions.c:(.text+0x1084ac): undefined reference to `input_event'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11cc0a): undefined reference to `get_key_pinnacle_color'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11cc4f): undefined reference to `get_key_pinnacle_grey'
drivers/built-in.o: In function `saa7134_input_fini':
(.text+0x11cd8b): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d1fa): undefined reference to `input_allocate_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d317): undefined reference to `input_register_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d6ca): undefined reference to `input_free_device'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c3f3): undefined reference to `ir_codes_hauppauge_new'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c450): undefined reference to `ir_codes_pinnacle_color'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c480): undefined reference to `ir_codes_purpletv'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c495): undefined reference to `ir_codes_pinnacle_grey'
drivers/built-in.o: In function `saa7134_ir_start':
(.text+0x11c622): undefined reference to `ir_rc5_timer_end'
drivers/built-in.o: In function `saa7134_ir_start':
(.text+0x11c637): undefined reference to `ir_rc5_timer_keyup'
drivers/built-in.o: In function `build_key':
saa7134-input.c:(.text+0x11c769): undefined reference to `ir_extract_bits'
saa7134-input.c:(.text+0x11c7ad): undefined reference to `ir_input_keydown'
saa7134-input.c:(.text+0x11c7f0): undefined reference to `ir_input_keydown'
saa7134-input.c:(.text+0x11c7f9): undefined reference to `ir_input_nokey'
saa7134-input.c:(.text+0x11c806): undefined reference to `ir_input_nokey'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ca07): undefined reference to `ir_codes_encore_enltv'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11caf6): undefined reference to `ir_input_init'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cbf2): undefined reference to `ir_codes_avermedia'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc24): undefined reference to `ir_codes_pctv_sedna'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc53): undefined reference to `ir_codes_flydvb'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc85): undefined reference to `ir_codes_videomate_tv_pvr'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ccb7): undefined reference to `ir_codes_pixelview'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cce9): undefined reference to `ir_codes_eztv'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cd1b): undefined reference to `ir_codes_manli'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cda8): undefined reference to `ir_codes_cinergy'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cdd7): undefined reference to `ir_codes_flyvideo'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ce06): undefined reference to `ir_codes_asus_pc39'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ce7d): undefined reference to `ir_codes_gotview7135'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cee1): undefined reference to `ir_codes_proteus_2309'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Media ir-functions uses input_(*) functions so it should depend
on the INPUT config symbol.
drivers/built-in.o: In function `ir_input_key_event':
ir-functions.c:(.text+0x10849a): undefined reference to `input_event'
ir-functions.c:(.text+0x1084ac): undefined reference to `input_event'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
irq handlers have returned a return value for years now... catch up with
the times.
Also, ditch unneeded prototype.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134: fix analog audio in on medion md8800 quadro, aka CTX944
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch enables QAM Annex-B support (US digital cable)
for the s5h1409 VSB/QAM demodulator.
Tested successfully with the mt2131 tuner,
present on the following supported boards:
Hauppauge WinTV-HVR-1250
Hauppauge WinTV-HVR-1800
Hauppauge WinTV-HVR-1800lp
This patch is also known to work with an upcoming XC5000 tuner driver.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a pointer to the (recently posted) Cafe data sheet.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the system is suspended while the camera is streaming, it will not
continue streaming on resume. Save the state properly so that resume
works.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The V4L1 spec says that the image size should be with with VIDIOCSWIN before
requesting buffers with VIDIOCGMBUF and capturing into them with
VIDIOCMCAPTURE.
But it seems that many apps don't do this. They set the size using the fields
in the VIDIOCMCAPTURE ioctl. The driver doesn't know what size to capture
until it actually starts to capture. In particular, it doesn't know what size
to capture until it has already mmap the captured buffers. Which is quite
stupid. Why V4L1 has size and format fields for VIDIOCMCAPTURE I have no idea.
Many drivers don't support this, including those using v4l1-compat.
The bttv does, which is probably the only reason such broken software is so
prevalent.
But, the driver doesn't adjust its idea of what size is being captured when it
is set this way. If you try to query the driver's current setting with
v4l2-ctl, it won't be correct.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bttv driver instists that the depth specified in the call to VIDIOCSPICT
match the pixel format specified in the same call.
vlc doesn't set the depth field, which makes the SPICT ioctl always fail.
The V4L1 standard is not clear on how most operation are supposed to work, and
this is no exception. The depth field would appear to be entirely redundant,
as the pixel format specifies a specific depth. It could be that this field
was only meant for output from the *G*PICT ioctl and should be ignored in
*S*PICT. This is in fact what the v4l1-compat wrapper does.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It is referenced both from __devinit code (ivtv_probe) and
normal .text (ivtv_process_eeprom), and therefore cannot
be discarded via __devexit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commits
58b053e4ce ("Update arch/ to use sg helpers")
45711f1af6 ("[SG] Update drivers to use sg helpers")
fa05f1286b ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (37 commits)
V4L/DVB (6382): saa7134: fix NULL dereference at suspend time for cards without IR receiver
V4L/DVB (6380): ivtvfb: Removal of the 'osd_compat' module option
V4L/DVB (6379): patch which improves GotView Saa7135 remote control
V4L/DVB (6378b): Updates info about the removal of V4L1 at feature-removal-schedule.txt
V4L/DVB (6378a): Removal of VIDIOC_[G|S]_MPEGCOMP from feature-removal-schedule.txt
V4L/DVB (6378): DiB0700-device: Using 1.10 firmware
V4L/DVB (6357): pvrusb2: Improve encoder chip health tracking
V4L/DVB (6356): "while (!ca->wakeup)" breaks the CAM initialisation
V4L/DVB (6352): ir-kbd-i2c: Missing break statement
V4L/DVB (6350): V4L: possible leak in em28xx_init_isoc
V4L/DVB (6348): ivtv: undo video mute when closing the radio
V4L/DVB (6347): ivtv: fix video mute when radio is used
V4L/DVB (6346): ivtvfb: YUV output size fix when ivtvfb is not loaded
V4L/DVB (6345): ivtvfb: YUV handling of an image which is not visible in the display area
V4L/DVB (6343): ivtvfb: check return value of unregister_framebuffer
V4L/DVB (6342): ivtv: fix circular locking (bug 9037)
V4L/DVB (6341): ivtv: fix resizing MPEG1 streams
V4L/DVB (6340): ivtvfb: screen mode change sometimes goes wrong
V4L/DVB (6339): ivtv: set the video color to black instead of green when capturing from the radio
V4L/DVB (6338): ivtv: fix incorrect EBUSY return
...
Calling saa7134_ir_stop at suspend is no good idea
for saa7134 cards without remote control.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to changes in the core ivtv driver as of release 1.0, the osd_compat
module option has been rendered obsolete. This patch removes the option and
all code associated with it.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
improve GoTView PCI7135 remote control working under linux.
Acked-by: Hermann Pitton <hermann-pitton@arcor.de>
Acked-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Eugene M. Roginskii <roginovicci@nm.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As for most of the users the 1.10 firmware is an improvement we should
use this firmware always now.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a minor change to help with tracking the viability of the
encoder chip within the PVR USB2 device.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Someone added a new case without adding a break to the one before it.
Thanks to Margus <b-berski at mbox200 dot swipnet dot se> for spotting this.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Coverity (CID 1929) spotted the following: if a transfer buffer
allocation fails, the last allocated urb is leaked (it hasn't been
stored in dev->urb[] yet so em28xx_uninit_isoc misses it). The patch
also includes a small typo fix.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the radio is active the video should be muted when a capture
starts. However, this was done at the wrong time and the mute settings
were overwritten when cx2341x_update was called.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the ivtvfb module isn't loaded, the valid YUV output area should be set to
full-screen. This patch fixes the case where the valid output area was not
reset when the output broadcast format was changed from NTSC to PAL. This
resulted in output being limited to the top 480 lines of the display.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the ivtvfb module is loaded, the YUV output is relative to the
framebuffer output. When a virtual screen size is used, the output area for
the YUV may actually be off screen. To prevent the hardware from crashing,
the current driver will ignore an off-screen position and leave the output
visible at the last on-screen position. This may not be desirable, so this
patch will switch off the YUV output should the image move off-screen, and
re-enable it should the image move on-screen again.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Prevent unloading the framebuffer if it is still in use.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If you try to access the video device from within an udev rule,
then you get into a circular locking situation.
Changed the driver to postpone the registration of the devices until
everything else has been fully initialized, so that the newly created
device can be used immediately.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Resizing an MPEG 1 stream would cut off the right half of the
image due to a missing divide by 2 in VIDIOC_S_FMT.
Also did some minor cleanup in this part of the code.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch partially reverts a previous change that caused the
CX2341X_OSD_SET_PIXEL_FORMAT firmware calls to be skipped when the pixel
format of the framebuffer wasn't altered by FBIOPUT_VSCREENINFO.
Unfortunately, another firmware call on the PVR350 sometimes scrambles the
display when trying to adjust the framebuffer settings. This patch re-enables
the CX2341X_OSD_SET_PIXEL_FORMAT calls to try and prevent this from
occurring.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trying to open the radio when a capture is in progress will make it
impossible to open the radio again since the radio stream wasn't released.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When a cx8802 sub-driver was unregistered, the struct cx8802_driver, which was
kmalloc()ed by cx8802_register_driver(), was deleted from the list of drivers,
but never freed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Less code and more efficient.
Got ride of a variable that counted the number of devices in
cx8802_unregister_driver() but was never used. Looked leftover from a
cut&paste.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It was a struct cx8802_driver for no apparent reason. Nothing uses a
cx8802_driver in the cx8802_dev struct. The only field that was used was
devlist, a list_head.
The code in cx8802_remove() that removed any loaded sub-drivers was broken.
It would delete the current list entry, but didn't use list_for_each_safe. It
also called list_del() on the list _head_ inside the list_for_each loop? It
would crash if it was run, which I don't think can ever happen.
Since the cx8802 sub-drivers use the cx8802 driver, they have to be unloaded
first. So there isn't any way for a sub-driver to still be loaded when
cx8802_remove() is called... Except maybe with PCI hot-plug, if one removes
the PCI card while the drivers are loaded?
So I left some code in to handle that if it's actually possible. It will
remove the sub-drivers from the device cx8802_remove() was called on, and only
that device. If one has two DVB cards and unplugs one, there is no reason to
unload the DVB drivers for both cards. I have no way to test this, but it
can't be worse than what was there before.
cx8802_get_driver() is passed a cx8802_dev pointer and looks for the requested
driver on that device. It first loops over the cx8802 device list looking for
the device it was passed, which is pointless. It doesn't need to find the
device pointer in the list, as it already has the pointer.
The list_head in the cx8802_driver struct, which joins all the _drivers_
attached to a device, was named devlist. Changed that to drvlist, since the
devlist is used for a list of _devices_ in other cx8802 structs.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
card_priv was only used to store a pointer to the vp3054 state struct.
There's no need to use a void * since it doesn't have multiple types.
Make the field conditional on VP3045 support. It was already conditional on
DVB support, but it's only used if VP3045 support is on, so that makes for a
better option to check.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add some ifdefs around fields only used for blackbird support, similar to the
way the dvb fields are only included with dvb support.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
make tvaudio thread freezeable, and add proper support for that
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes few more problems I found in my saa7134 resume code:
* Race between IRQ handler and .suspend()/.resume() functions
* Removes timeout timers on active buffers - those
buffers will be recaptured after resume
* Adds suspend/resume for IR code - probably
necessary if using polling mode
* Adds #ifdef CONFIG_PM overs suspend code
* Runs a quirk in set_tvnorm in suspend/resume too
* Rearranges the order of calls in saa7134_resume to
be exactly as in saa7134_initdev thus the card is
initialized in exactly the same way
* Since DMA audio capture suspend/resume isn't yet supported,
avoid re-enabling it on resume for now
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We shouldn't dereference "itv" when we know it's NULL...
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Initialize strength to zero.
Thanks to Adrian Bunk, who spotted this with the Coverity checker.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Both cx23885_initdev and cx23885_dev_setup free the device in their
error path so a failure in the latter causes a double-free. Since
cx23885_dev_setup is only called from cx23885_initdev, it should be safe
to remove its deallocation and leave the cleanup up to the allocating
function.
Coverity CID 1922.
Signed-off-by: Florin Malita <fmalita@gmail.com>
CC: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As videobuf_cgmbuf is defined only if CONFIG_VIDEO_V4L1_COMPAT is enabled,
move the EXPORT_SYMBOL_GPL declaration inside the #ifdef block. Fixes
compilation for x86_64 defconfig.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cinergyT2, remove bad usage of ERESTARTSYS
test of cinergyt2->disconnect_pending doesn't ensure pending signal and so
ERESTARTSYS would reach userspace, which is not permitted. Change it to
EAGAIN.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the obsolete VIDIOC_G_MPEGCOMP and VIDIOC_S_MPEGCOMP ioctls from
the V4L2 API as per the removal schedule (October 2007).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
struct video_device used to define a .hardware field. While
initialized on severl drivers, this field is never used inside V4L.
However, drivers using it need to include the old V4L1 header.
This seems to cause compilation troubles with some random configs.
Better just to remove it from all drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove obsolete V4L v1 reference.
Thanks to Ingo Molnar for pointing this issue.
Signed-off-by: Pekka Seppänen <pexu@kapsi.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Lets mixer apps display a dB range for the volume control.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add two mute controls. One mutes everything, the other just mutes the analog
pass-through output.
Rename the existing volume control. The controls are now:
Playback Volume
Playback Switch
Capture Switch
These names might seem odd, but I believe they are more correct. The previous
"Capture Volume" control didn't actually effect the volume of the captured
audio. Instead it controls the volume of the analog pass-thought output. It
appears that pass-through controls like this are usually considered to be in
the playback direction, not capture. For example, "CAPTURE feedback Playback
Volume" is the name used for a control that appears to have the same effect in
the ca0106 driver. We only have one volume control, so we can omit the
"CAPTURE feedback" part.
If someone where to add PCM playback support to the driver, then this would be
the volume control.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get rid of input BIT* duplicate defines
use newly global defined macros for input layer. Also remove includes of
input.h from non-input sources only for BIT macro definiton. Define the
macro temporarily in local manner, all those local definitons will be
removed further in this patchset (to not break bisecting).
BIT macro will be globally defined (1<<x)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <dtor@mail.ru>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: <lenb@kernel.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: <perex@suse.cz>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <vernux@us.ibm.com>
Cc: <malattia@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To be consistent with the use of attributes in the rest of the kernel
replace all use of __attribute_pure__ with __pure and delete the definition
of __attribute_pure__.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce freezer-friendly wrappers around wait_event_interruptible() and
wait_event_interruptible_timeout(), originally defined in <linux/wait.h>, to
be used in freezable kernel threads. Make some of the freezable kernel
threads use them.
This is necessary for the freezer to stop sending signals to kernel threads,
which is implemented in the next patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2c_algorithm.algo_control is about to be removed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This removes NOP implementations of i2c_algorithm.algo_control.
With this change, there are no implementations of this hook in
the kernel.org tree ... that hook seems about ripe to remove.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Breaks on any target that has copy_to_user() defined as a non-trivial
macro.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct cdev does not need the kobject name to be set, as it is never
used. This patch fixes up the few places it is set.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
[SKY2]: status polling loop (post merge)
[NET]: Fix NAPI completion handling in some drivers.
[TCP]: Limit processing lost_retrans loop to work-to-do cases
[TCP]: Fix lost_retrans loop vs fastpath problems
[TCP]: No need to re-count fackets_out/sacked_out at RTO
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
[TCP]: Kill almost unused variable pcount from sacktag
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
[IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
[NETFILTER]: x_tables: add missing ip6t_modulename aliases
[NETFILTER]: nf_conntrack_tcp: fix connection reopening
[QETH]: fix qeth_main.c
[NETLINK]: fib_frontend build fixes
[IPv6]: Export userland ND options through netlink (RDNSS support)
[9P]: build fix with !CONFIG_SYSCTL
[NET]: Fix dev_put() and dev_hold() comments
[NET]: make netlink user -> kernel interface synchronious
[NET]: unify netlink kernel socket recognition
[NET]: cleanup 3rd argument in netlink_sendskb
...
Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.
(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rest of V4L files.
There is one list_for_each+list_entry in cpia_pp.c that
wasn't changed because it expects the loop iterator to remain NULL if
the list is empty.
A bug in vivi is fixed; the 'safe' version needs to be used because the loop
deletes the list entries.
Simplify a second loop in vivi and get rid if an un-used variable in that loop.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A couple loops weren't changed because they expected the loop iterator
to be left as NULL if the list was empty. Maybe the code should just
check for that first, then loop?
Adjust some of the loop logic to be simpler.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also fixed a few cases of cut&paste errors where 'buf' would be set to the
first entry in the list prior to be used as the loop iterator. In one case
the value of buf was used before it was changed, but the rest were
unnecessary.
There was one list_for_each+list_entry loop that wasn't changed, since it
depending on the loop iterator being left as NULL if the list was empty.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
CC: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
zc0301, remove bad usage of ERESTARTSYS
down_read_trylock can't be interrupted and so ERESTARTSYS would reach
userspace, which is not permitted. Change it to EAGAIN
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
w9968cf, remove bad usage of ERESTARTSYS
down_read_trylock can't be interrupted and so ERESTARTSYS would reach
userspace, which is not permitted. Change it to EAGAIN
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*Disable DMA explictly on suspend
*Enable DMA on resume, after all buffers were configured
*Disable overlay on resume - apps should enable it when X is resumed
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The return value of videobuf_alloc() is unchecked but this function will
return NULL on an error. Check for NULL and make videobuf_reqbufs()
return the number of successfully allocated buffers.
Also, fix saa7146_video.c and bttv-driver.c to use this returned
buffer count.
Tested against the vivi driver. Not tested against saa7146 or bt8xx
devices.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The prototypes for the show and store methods of a device_attribute changed in
kernel 2.6.13, but the code in pvrusb2 was never updated. I guess the
DEBUGIFC stuff isn't used much....
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It needs to select VIDEOBUF_GEN and VIDEOBUF_DMA_SG, since it uses those
modules.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Recognize the KWorld ATSC115 PCI ID as a hardware clone of the ATSC110.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The currently used "struct class_device" will be removed from the
kernel. Here is a patch that converts all users in drivers/media/video/
to struct device.
Reviewed-by: Thierry Merle <thierry.merle@free.fr>
Reviewed-by: Mike Isely <isely@pobox.com>
Reviewed-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the past, videobuf_queue_init were used to initialize PCI DMA videobuffers.
This patch renames it, to avoid confusion with the previous kernel API, doing:
s/videobuf_queue_init/void videobuf_queue_core_init/
Also, the operations is now part of the function parameter. The function will
also add a test if this is defined, otherwise producing BUG.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This workaround fix a bug that happens on some SMP machines. On those machines,
videobuf_iolock is called too soon, before file .mmap handler. This patch calls
the scheduler before iolocking, allowing it to properly call the pending mmap.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before the videobuf redesign, a procedure for re-using videobuf without PCI
scatter/gather where provided by changing the pci-dependent operations by
other operations.
With the newer approach, those methods are obsolete and can safelly be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx23885 driver were converted to use the newer videobuf support. Unfortunately,
the constructor weren't changed. This causes an oops, since the abstract methods
(implemented as callbacks) aren't defined.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
No need to cast the void pointer returned by kmalloc() in
drivers/media/video/zoran_driver.c::v4l_fbuffer_alloc().
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx23885 was still uses the old video-buf includes and code, which would only
`work' if one happened to be compiling against a kernel that had the old
headers. Even then, it wouldn't actually work, it would just compile without
errors.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CONFIG_VIDEO_BUF_DVB became CONFIG_VIDEOBUF_DVB.
But in these cases, it makes more sense to use CONFIG_VIDEO_SAA7134_DVB
or CONFIG_VIDEO_CX88_DVB_MODULE depending on the driver.
The reference in cx23885.h should just be removed, as the code there needs to
be included if DVB is on or off. I do not think you can even compile the
cx23885 driver without DVB. It's clearly just leftover from when the file was
obvious copied from the cx88 driver (which is not mentioned in the copyright
BTW).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Here's an attempted update to the full kthread API + wake_up_process:
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
CC: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If videobuf_read_stream reads two or more buffers it was overwriting the first one
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
http://thread.gmane.org/gmane.comp.video.video4linux/34978/focus=34981
Reviewed-by: Ricardo Cerqueira <v4l@cerqueira.org>
The reading/streaming fields are used for mutual exclusion of the queue and
should be protected by the queue lock.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
http://thread.gmane.org/gmane.comp.video.video4linux/34978/focus=34981
Reviewed-by: Ricardo Cerqueira <v4l@cerqueira.org>
The "resource" locking in vivi isn't needed since
streamon/streamoff/read_stream do mutual exclusion using
q->reading/q->streaming.
Plus it is sort of broken:
a) res_locked() use in vivi_read() is racey.
b) res_free() calls mutex_lock twice causing streamoff to break
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since vivi is using videobuf_read_stream() it can use videobuf_poll_stream()
now.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the client provides V4L2_FIELD_ANY vivi should return a valid field :)
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
