Add some infrastructure for saving and restoring the context of an
SPE. This patch creates a new structure that can hold the whole
state of a physical SPE in memory. It also contains code that
avoids races during the context switch and the binary code that
is loaded to the SPU in order to access its registers.
The actual PPE- and SPE-side context switch code are two separate
patches.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the current version of the spu file system, used
for driving SPEs on the Cell Broadband Engine.
This release is almost identical to the version for the
2.6.14 kernel posted earlier, which is available as part
of the Cell BE Linux distribution from
http://www.bsc.es/projects/deepcomputing/linuxoncell/.
The first patch provides all the interfaces for running
spu application, but does not have any support for
debugging SPU tasks or for scheduling. Both these
functionalities are added in the subsequent patches.
See Documentation/filesystems/spufs.txt on how to use
spufs.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the necessary core bus support used by device drivers
that sit on the IBM GX bus on modern pSeries machines like the Galaxy
infiniband for example. It provide transparent DMA ops (the low level
driver works with virtual addresses directly) along with a simple bus
layer using the Open Firmware matching routines.
Signed-off-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleanup patch speeds up the null syscall path on ppc64 by about 3%,
and brings the ppc32 and ppc64 code slightly closer together.
The ppc64 code was checking current_thread_info()->flags twice in the
syscall exit path; once for TIF_SYSCALL_T_OR_A before disabling
interrupts, and then again for TIF_SIGPENDING|TIF_NEED_RESCHED etc after
disabling interrupts. Now we do the same as ppc32 -- check the flags
only once in the fast path, and re-enable interrupts if necessary in the
ptrace case.
The patch abolishes the 'syscall_noerror' member of struct thread_info
and replaces it with a TIF_NOERROR bit in the flags, which is handled in
the slow path. This shortens the syscall entry code, which no longer
needs to clear syscall_noerror.
The patch adds a TIF_SAVE_NVGPRS flag which causes the syscall exit slow
path to save the non-volatile GPRs into a signal frame. This removes the
need for the assembly wrappers around sys_sigsuspend(),
sys_rt_sigsuspend(), et al which existed solely to save those registers
in advance. It also means I don't have to add new wrappers for ppoll()
and pselect(), which is what I was supposed to be doing when I got
distracted into this...
Finally, it unifies the ppc64 and ppc32 methods of handling syscall exit
directly into a signal handler (as required by sigsuspend et al) by
introducing a TIF_RESTOREALL flag which causes _all_ the registers to be
reloaded from the pt_regs by taking the ret_from_exception path, instead
of the normal syscall exit path which stomps on the callee-saved GPRs.
It appears to pass an LTP test run on ppc64, and passes basic testing on
ppc32 too. Brief tests of ptrace functionality with strace and gdb also
appear OK. I wouldn't send it to Linus for 2.6.15 just yet though :)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved 83xx and QUICC Engine interrupt handling code into arch/powerpc
as a precursor of getting 83xx sub-arch building in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges, to some extent, the PPC32 and PPC64 kexec implementations.
We adopt the PPC32 approach of having ppc_md callbacks for the kexec functions.
The current PPC64 implementation becomes the "default" implementation for PPC64
which platforms can select if they need no special treatment.
I've added these default callbacks to pseries/maple/cell/powermac, this means
iSeries no longer supports kexec - but it never worked anyway.
I've renamed PPC32's machine_kexec_simple to default_machine_kexec, inline with
PPC64. Judging by the comments it might be better named machine_kexec_non_of,
or something, but at the moment it's the only implementation for PPC32 so it's
the "default".
Kexec requires machine_shutdown(), which is in machine_kexec.c on PPC32, but we
already have in setup-common.c on powerpc. All this does is call
ppc_md.nvram_sync, which only powermac implements, so instead make
machine_shutdown a ppc_md member and have it call core99_nvram_sync directly
on powermac.
I've also stuck relocate_kernel.S into misc_32.S for powerpc.
Built for ARCH=ppc, and 32 & 64 bit ARCH=powerpc, with KEXEC=y/n. Booted on
P5 LPAR and successfully kexec'ed.
Should apply on top of 493f25ef40.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the EXPORT_SYMBOL'ed but completely unused variable
ucSystemType and removes the unneeded EXPORT_SYMBOL(_prep_type).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch contains the following cleanups:
- addrconf.c: make addrconf_dad_stop() static
- inet6_connection_sock.c should #include <net/inet6_connection_sock.h>
for getting the prototypes of it's global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there's no longer any external user of ip_fragment() we can make
it static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unlocking disappeared during commit
5793f4be23.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle NAT of decapsulated IPsec packets by reconstructing the struct flowi
of the original packet from the conntrack information for IPsec policy
checks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the conntrack reference until policy checks have been performed for
IPsec NAT support. The reference needs to be dropped before a packet is
queued to avoid having the conntrack module unloadable.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NAT changes the key used for the xfrm lookup it needs to be done
again. If a new policy is returned in POST_ROUTING the packet needs
to be passed to xfrm4_output_one manually after all hooks were called
because POST_ROUTING is called with fixed okfn (ip_finish_output).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for IPsec support for NAT:
Use conntrack information instead of saving the saving and comparing the
addresses to determine if a packet was NATed and needs to be rerouted to
make it easier to extend the key.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_me_harder doesn't use the port numbers of the xfrm lookup and
uses ip_route_input for non-local addresses which doesn't do a xfrm
lookup, ip6_route_me_harder doesn't do a xfrm lookup at all.
Use xfrm_decode_session and do the lookup manually, make sure both
only do the lookup if the packet hasn't been transformed already.
Makeing sure the lookup only happens once needs a new field in the
IP6CB, which exceeds the size of skb->cb. The size of skb->cb is
increased to 48b. Apparently the IPv6 mobile extensions need some
more room anyway.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset IPSKB_XFRM_TUNNEL_SIZE flags in ipip and ip_gre hard_start_xmit
function before the packet reenters IP. This is neccessary so the
encapsulated packets are checked not to be oversized in xfrm4_output.c
again. Reset all flags in sit when a packet changes its address family.
Also remove some obsolete IPSKB flags.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the innermost transform uses transport mode the decapsulated packet
is not visible to netfilter. Pass the packet through the PRE_ROUTING and
LOCAL_IN hooks again before handing it to upper layer protocols to make
netfilter-visibility symetrical to the output path.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move nextheader offset to the IP6CB to make it possible to pass a
packet to ip6_input_finish multiple times and have it skip already
parsed headers. As a nice side effect this gets rid of the manual
hopopts skipping in ip6_input_finish.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call netfilter hooks before IPsec transforms. Packets visit the
FORWARD/LOCAL_OUT and POST_ROUTING hook before the first encapsulation
and the LOCAL_OUT and POST_ROUTING hook before each following tunnel mode
transform.
Patch from Herbert Xu <herbert@gondor.apana.org.au>:
Move the loop from dst_output into xfrm4_output/xfrm6_output since they're
the only ones who need to it. xfrm{4,6}_output_one() processes the first SA
all subsequent transport mode SAs and is called in a loop that calls the
netfilter hooks between each two calls.
In order to avoid the tail call issue, I've added the inline function
nf_hook which is nf_hook_slow plus the empty list check.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
security/selinux/xfrm.c:155:10: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing prevents a user to modprobe a framebuffer driver from e.g. the
xterm prompt. As a result, the set_par() function of the driver will be
called from fbcon_init().
This is fatal as a lot of X / framebuffer combinations are unable to
recover from set_par() reprogramming the graphics controller in
KD_GRAPHICS mode.
It is also unnecessary as the set_par() function will be called during a
switch to KD_TEXT anyway. Because of this no side effects are possible.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the ibmasm driver to use the dynamic allocation of input_dev
structs to work with the sysfs subsystem.
Vojtech: Fixed some problems/bugs in the patch.
Dmitry: Fixed some more.
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andre McCurdy
Replaces generic swab32 routine with a more ARM friendly version.
Reduces kernel text size by approx 1200 bytes when compiled with
3.4.4 and approx 2400 bytes with 4.0.2
Probably some performance benefit as well.
Signed-off-by: Andre McCurdy <armccurdy@yahoo.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Fix a gcc4 build error (incomplete element type) in the pxa SharpSL
PM code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
Correction of the code broken by update
whole-tree platform devices update.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've spent the past 3 days digging into a glibc testsuite failure in
current CVS, specifically libc/rt/tst-cputimer1.c The thr1 and thr2
timers fire too early in the second pass of this test. The second
pass is noteworthy because it makes use of intervals, whereas the
first pass does not.
All throughout the posix-cpu-timers.c code, the calculation of the
process sched_time sum is implemented roughly as:
unsigned long long sum;
sum = tsk->signal->sched_time;
t = tsk;
do {
sum += t->sched_time;
t = next_thread(t);
} while (t != tsk);
In fact this is the exact scheme used by check_process_timers().
In the case of check_process_timers(), current->sched_time has just
been updated (via scheduler_tick(), which is invoked by
update_process_times(), which subsequently invokes
run_posix_cpu_timers()) So there is no special processing necessary
wrt. that.
In other contexts, we have to allot for the fact that tsk->sched_time
might be a bit out of date if we are current. And the
posix-cpu-timers.c code uses current_sched_time() to deal with that.
Unfortunately it does so in an erroneous and inconsistent manner in
one spot which is what results in the early timer firing.
In cpu_clock_sample_group_locked(), it does this:
cpu->sched = p->signal->sched_time;
/* Add in each other live thread. */
while ((t = next_thread(t)) != p) {
cpu->sched += t->sched_time;
}
if (p->tgid == current->tgid) {
/*
* We're sampling ourselves, so include the
* cycles not yet banked. We still omit
* other threads running on other CPUs,
* so the total can always be behind as
* much as max(nthreads-1,ncpus) * (NSEC_PER_SEC/HZ).
*/
cpu->sched += current_sched_time(current);
} else {
cpu->sched += p->sched_time;
}
The problem is the "p->tgid == current->tgid" test. If "p" is
not current, and the tgids are the same, we will add the process
t->sched_time twice into cpu->sched and omit "p"'s sched_time
which is very very very wrong.
posix-cpu-timers.c has a helper function, sched_ns(p) which takes care
of this, so my fix is to use that here instead of this special tgid
test.
The fact that current can be one of the sub-threads of "p" points out
that we could make things a little bit more accurate, perhaps by using
sched_ns() on every thread we process in these loops. It also points
out that we don't use the most accurate value for threads in the group
actively running other cpus (and this is mentioned in the comment).
But that is a future enhancement, and this fix here definitely makes
sense.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ib_create_ah_from_wc() doesn't create the correct return address (AH)
when there is a GRH present (source & dest GIDs need to be swapped).
Signed-off-by: Ralph Campbell <ralphc@pathscale.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_uverbs_create_cq() should release the completion channel event file
if an error occurs after it looks it up. Also, if userspace asks for
a completion channel and we don't find it, an error should be returned
instead of silently creating a CQ without a completion channel.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If an operation fails after incrementing an object's reference count,
then it should decrement the reference count on the error path.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
