While both level- and edge-triggered GPIOs are capable of generating
interrupts, only edge-triggered GPIOs are capable of generating a
module-level wakeup to the PRCM (c.f. 34xx NDA TRM section 25.5.3.2.)
In order to ensure that devices using level-triggered GPIOs as
interrupts can also cause wakeups (e.g. from idle), this patch enables
edge-triggering for wakeup-enabled, level-triggered GPIOs when a GPIO
bank is runtime-suspended (which also happens during idle.)
This fixes a problem found in GPMC-connected network cards with GPIO
interrupts (e.g. smsc911x on Zoom3, Overo, ...) where network booting
with NFSroot was very slow since the GPIO IRQs used by the NIC were
not generating PRCM wakeups, and thus not waking the system from idle.
NOTE: until v3.3, this boot-time problem was somewhat masked because
the UART init prevented WFI during boot until the full serial driver
was available. Preventing WFI allowed regular GPIO interrupts to fire
and this problem was not seen. After the UART runtime PM cleanups, we
no longer avoid WFI during boot, so GPIO IRQs that were not causing
wakeups resulted in very slow IRQ response times.
Tested on platforms using level-triggered GPIOs for network IRQs using
the SMSC911x NIC: 3530/Overo and 3630/Zoom3.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPW8yUAAoJEHm+PkMAQRiGhFIH/RGUPxGmUkJv8EP5I4HDA4dJ
c6/PrzZCHs8rxzYzvn7ojXqZGXTOAA5ZgS9A6LkJ2sxMFvgMnkpFi6B4CwMzizS3
vLWo/HNxbiTCNGFfQrhQB8O58uNI8wOBa87lrQfkXkDqN0cFhdjtIxeY1BD9LXIo
qbWysGxCcZhJWHapsQ3NZaVJQnIK5vA/+mhyYP4HzbcHI3aWnbIEZ8GQKeY28Ch0
+pct5UQBjZavV5SujaW0Xd65oIiycm8XHAQw6FxQy//DfaabauWgFteR162Q/oew
xxUBDOHF3nO1bdteHHaYqxig0j1MbIHsqxTnE/neR8UryF04//1SFF7DYuY/1pg=
=SV5V
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc7' into gpio/next
Linux 3.3-rc7. Merged into the gpio branch to pick up gpio bugfixes already
in mainline before queueing up move v3.4 patches
Two fixes are queued up. The first is an additional fix for the OMAP
initialization order issue and the second patch fixes a possible section
mismatch which can lead to a kernel crash in the AMD IOMMU driver when
suspend/resume is used and the compiler has not inlined the
iommu_set_device_table function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PZDd
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull two IOMMU fixes from Joerg Roedel:
"The first is an additional fix for the OMAP initialization order issue
and the second patch fixes a possible section mismatch which can lead
to a kernel crash in the AMD IOMMU driver when suspend/resume is used
and the compiler has not inlined the iommu_set_device_table function."
* tag 'iommu-fixes-v3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
x86/amd: iommu_set_device_table() must not be __init
ARM: OMAP: fix iommu, not mailbox
Pull radeon drm stuff from Dave Airlie:
"Just some radeon fixes, one is for an oops where we run out of ioremap
space on some big hardware systems in 32-bit mode, stuff doesn't work
properly but at least the machine will boot.
One regression fix, and two bugs, one hw, one blit code."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: fix hdmi duallink checks
drm/radeon/kms: set SX_MISC in the r6xx blit code (v2)
drm/radeon: deal with errors from framebuffer init path.
drm/radeon: fix a semaphore deadlock on pre cayman asics
Pull networking from David Miller:
1) IPV4 routing metrics can become stale when routes are changed by the
administrator, fix from Steffen Klassert.
2) atl1c does "val |= XXX;" where XXX is a bit number not a bit mask,
fix by using set_bit. From Dan Carpenter.
3) Memory accounting bug in carl9170 driver results in wedged TX queue.
Fix from Nicolas Cavallari.
4) iwlwifi accidently uses "sizeof(ptr)" instead of "sizeof(*ptr)", fix
from Johannes Berg.
5) Openvswitch doesn't honor dp_ifindex when doing vport lookups, fix
from Ben Pfaff.
6) ehea conversion to 64-bit stats lost multicast and rx_errors
accounting, fix from Eric Dumazet.
7) Bridge state transition logging in br_stp_disable_port() is busted,
it's emitted at the wrong time and the message is in the wrong tense,
fix from Paulius Zaleckas.
8) mlx4 device erroneously invokes the queue resize firmware operation
twice, fix from Jack Morgenstein.
9) Fix deadlock in usbnet, need to drop lock when invoking usb_unlink_urb()
otherwise we recurse into taking it again. Fix from Sebastian Siewior.
10) hyperv network driver uses the wrong driver name string, fix from
Haiyang Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net/hyperv: Use the built-in macro KBUILD_MODNAME for this driver
net/usbnet: avoid recursive locking in usbnet_stop()
route: Remove redirect_genid
inetpeer: Invalidate the inetpeer tree along with the routing cache
mlx4_core: fix bug in modify_cq wrapper for resize flow.
atl1c: set ATL1C_WORK_EVENT_RESET bit correctly
bridge: fix state reporting when port is disabled
bridge: br_log_state() s/entering/entered/
ehea: restore multicast and rx_errors fields
openvswitch: Fix checksum update for actions on UDP packets.
openvswitch: Honor dp_ifindex, when specified, for vport lookup by name.
iwlwifi: fix wowlan suspend
mwifiex: reset encryption mode flag before association
carl9170: fix frame delivery if sta is in powersave mode
carl9170: Fix memory accounting when sta is in power-save mode.
Fixes up a duplicate #include, adds an empty implementation of
of_find_compatible_node() and make git ignore .dtb files. And fix
up bus name on OF described PHYs. Nothing exciting here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/fxH
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull minor devicetree bug fixes and documentation updates from Grant Likely:
"Fixes up a duplicate #include, adds an empty implementation of
of_find_compatible_node() and make git ignore .dtb files. And fix up
bus name on OF described PHYs. Nothing exciting here."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
doc: dt: Fix broken reference in gpio-leds documentation
of/mdio: fix fixed link bus name
of/fdt.c: asm/setup.h included twice
of: add picochip vendor prefix
dt: add empty of_find_compatible_node function
ARM: devicetree: Add .dtb files to arch/arm/boot/.gitignore
Russell King (1):
Fix section mismatch in spi-pl022.c
Minor fix for pl022_dma_probe() function which was put in the wrong section.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nTfV
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI section mismatch bug fix for v3.3-rc3 from Grant Likely:
"Minor fix for pl022_dma_probe() function which was put in the wrong
section."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
Fix section mismatch in spi-pl022.c
1bd612a hwmon: (jc42) Add support for AT30TS00, TS3000GB2, TSE2002GB2, and MCP9804
7ad6307 hwmon: (zl6100) Maintain delay parameter in driver instance data
7cb3c44 hwmon: (pmbus_core) Fix maximum number of POUT alarm attributes
4de8612 hwmon: (jc42) Add support for ST Microelectronics STTS2002 and STTS3000
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=mjD6
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull four hwmon patches from Guenter Roeck
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (jc42) Add support for AT30TS00, TS3000GB2, TSE2002GB2, and MCP9804
hwmon: (zl6100) Maintain delay parameter in driver instance data
hwmon: (pmbus_core) Fix maximum number of POUT alarm attributes
hwmon: (jc42) Add support for ST Microelectronics STTS2002 and STTS3000
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Olaf Hering <olaf@aepfle.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is called from enable_iommus(), which in turn is used
from amd_iommu_resume().
Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Mesa may set it to 1, causing all primitives to be killed.
v2: also update the r7xx code
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|kernel BUG at kernel/rtmutex.c:724!
|[<c029599c>] (rt_spin_lock_slowlock+0x108/0x2bc) from [<c01c2330>] (defer_bh+0x1c/0xb4)
|[<c01c2330>] (defer_bh+0x1c/0xb4) from [<c01c3afc>] (rx_complete+0x14c/0x194)
|[<c01c3afc>] (rx_complete+0x14c/0x194) from [<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0)
|[<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0) from [<c01e1ff4>] (musb_giveback+0x34/0x40)
|[<c01e1ff4>] (musb_giveback+0x34/0x40) from [<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0)
|[<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0) from [<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c)
|[<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c) from [<c01e2ed0>] (musb_urb_dequeue+0xec/0x108)
|[<c01e2ed0>] (musb_urb_dequeue+0xec/0x108) from [<c01cbb90>] (unlink1+0xbc/0xcc)
|[<c01cbb90>] (unlink1+0xbc/0xcc) from [<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8)
|[<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8) from [<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58)
|[<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58) from [<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c)
|[<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c) from [<c01c2d68>] (usbnet_stop+0x100/0x15c)
|[<c01c2d68>] (usbnet_stop+0x100/0x15c) from [<c020f718>] (__dev_close_many+0x94/0xc8)
defer_bh() takes the lock which is hold during unlink_urbs(). The safe
walk suggest that the skb will be removed from the list and this is done
by defer_bh() so it seems to be okay to drop the lock here.
Cc: stable@kernel.org
Reported-by: AnÃbal Almeida Pinto <anibal.pinto@efacec.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The actual FW command is called in procedure "handle_resize".
Code incorrectly invoked the FW command again (in good flow), in
the modify_cq wrapper function.
Fix by skipping second FW invocation unconditionally for resize.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATL1C_WORK_EVENT_RESET is zero so the original code here is a nop. The
intent was to set the zero bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 239c562c94 (ehea: Add 64bit statistics) added a regression,
since we no longer report multicast & rx_errors fields, taken from
port->stats structure. These fields are updated in ehea_update_stats()
every second.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per datasheet, the voltage output is defined as
from SEL[6:0] = 3 to 64 (dec)
Vout= (SEL[6:0] × 12.5 mV + 562.5 mV)
The list_voltage returns the vout as
600mV + selector * 12.5mV
and so equivalent VSEL is selector + 3.
Adding 3 on selector when configuring VSEL register for
VDDCTRL output.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix dm-raid flush support.
Both md and dm have support for flush, but the dm-raid target
forgot to set the flag to indicate that flushes should be
passed on. (Important for data integrity e.g. with writeback cache
enabled.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The 'rebuild' parameter is used to rebuild individual devices in an
array (e.g. resynchronize a RAID1 device or recalculate a parity device
in higher RAID). The MD_CHANGE_DEVS flag must be set when this
parameter is given in order to write out the superblocks and make the
change take immediate effect. The code that handles new devices in
super_load already sets MD_CHANGE_DEVS and 'FirstUse'. (The 'FirstUse'
flag was being set as a special case for rebuilds in
super_init_validation.)
Add a condition for rebuilds in super_load to take care of both flags
without the special case in 'super_init_validation'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Correct the number of mapped sectors shown on a thin device's
status line by decrementing td->mapped_blocks in __remove() each time
a block is removed.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If dm_sm_disk_create() fails the superblock must be unlocked.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The __open_device() error paths in __create_thin() and __create_snap()
incorrectly call __close_device() even if td was not initialized by
__open_device(). Remove this.
Also document __open_device() return values, remove a redundant
td->changed = 1 in __create_thin(), and insert an additional
safeguard against creating an already-existing device.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The following BUG is hit on the first read that is submitted to a dm
flakey test device while the device is "down" if the corrupt_bio_byte
feature wasn't requested when the device's table was loaded.
Example DM table that will hit this BUG:
0 2097152 flakey 8:0 2048 0 30
This bug was introduced by commit a3998799fb
(dm flakey: add corrupt_bio_byte feature) in v3.1-rc1.
BUG: unable to handle kernel paging request at ffff8801cfce3fff
IP: [<ffffffffa008c233>] corrupt_bio_data+0x6e/0xae [dm_flakey]
PGD 1606063 PUD 0
Oops: 0002 [#1] SMP
...
Call Trace:
<IRQ>
[<ffffffffa008c2b5>] flakey_end_io+0x42/0x48 [dm_flakey]
[<ffffffffa00dca98>] clone_endio+0x54/0xb6 [dm_mod]
[<ffffffff81130587>] bio_endio+0x2d/0x2f
[<ffffffff811c819a>] req_bio_endio+0x96/0x9f
[<ffffffff811c94b9>] blk_update_request+0x1dc/0x3a9
[<ffffffff812f5ee2>] ? rcu_read_unlock+0x21/0x23
[<ffffffff811c96a6>] blk_update_bidi_request+0x20/0x6e
[<ffffffff811c9713>] blk_end_bidi_request+0x1f/0x5d
[<ffffffff811c978d>] blk_end_request+0x10/0x12
[<ffffffff8128f450>] scsi_io_completion+0x1e5/0x4b1
[<ffffffff812882a9>] scsi_finish_command+0xec/0xf5
[<ffffffff8128f830>] scsi_softirq_done+0xff/0x108
[<ffffffff811ce284>] blk_done_softirq+0x84/0x98
[<ffffffff81048d19>] __do_softirq+0xe3/0x1d5
[<ffffffff8138f83f>] ? _raw_spin_lock+0x62/0x69
[<ffffffff810997cf>] ? handle_irq_event+0x4c/0x61
[<ffffffff8139833c>] call_softirq+0x1c/0x30
[<ffffffff81003b37>] do_softirq+0x4b/0xa3
[<ffffffff81048a39>] irq_exit+0x53/0xca
[<ffffffff81398acd>] do_IRQ+0x9d/0xb4
[<ffffffff81390333>] common_interrupt+0x73/0x73
...
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.1+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes a crash by recognising discards in dm_io.
Currently dm_mirror can send REQ_DISCARD bios if running over a
discard-enabled device and without support in dm_io the system
crashes badly.
BUG: unable to handle kernel paging request at 00800000
IP: __bio_add_page.part.17+0xf5/0x1e0
...
bio_add_page+0x56/0x70
dispatch_io+0x1cf/0x240 [dm_mod]
? km_get_page+0x50/0x50 [dm_mod]
? vm_next_page+0x20/0x20 [dm_mod]
? mirror_flush+0x130/0x130 [dm_mirror]
dm_io+0xdc/0x2b0 [dm_mod]
...
Introduced in 2.6.38-rc1 by commit 5fc2ffeabb
(dm raid1: support discard).
Signed-off-by: Milan Broz <mbroz@redhat.com>
Cc: stable@kernel.org
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If 'argc' is zero we jump to the 'out:' label, but this leaks the
(unused) memory that 'dm_split_args()' allocated for 'argv' if the
string being split consisted entirely of whitespace. Jump to the
'out_argv:' label instead to free up that memory.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A global delay parameter has the side effect of being overwritten with 0 if a
single ZL2004 or ZL6105 is instantiated. If other chips supported by the same
driver are in the system, this will result in access errors for those chips.
To solve the problem, keep a per-instance copy of the delay parameter, and do
not change the original parameter.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.1+
Acked-by: Jean Delvare <khali@linux-fr.org>
There are up to three POUT alarm attributes, not two, since cap_alarm was added.
Reported-by: Michele Petracca <mi.petracca@gmail.com>
Cc: stable@vger.kernel.org # 3.0+ [3.0 will need backport]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These are fully compatible with Jedec JC 42.4 as far as I can see.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Pull input updates from Dmitry Torokhov: "Just a few driver fixups,
nothing exciting."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - fix 3rd-gen Bamboo MT when 4+ fingers are in use
Input: twl4030-vibra - use proper guard for PM methods
Input: evdev - fix variable initialisation
Input: wacom - add missing LEDS_CLASS to Kconfig
Input: ALPS - fix touchpad detection when buttons are pressed
We've been getting occasional oops running a 32-bit kernel on a certain
system in our RHEL test hw. It appears that we fail to get sufficent ioremap
space for the framebuffer, and this leads to an oops.
This patch should fix the oops and leave a message in the logs we can
check for.
A future fix would probably to resize the console to a size that we can
ioremap.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The out of order execution of semaphore commands on
pre cayman asics doesn't work correctly and can
cause deadlocks, so turn it off for now.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The message count field uses three bits of storage, not two.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pull networking fixes from David Miller:
1) TCP can chop up SACK'd SKBs below below the unacked send sequence and
that breaks lots of stuff. Fix from Neal Cardwell.
2) There is code in ipv6 to properly join and leave the all-routers
multicast code when the forwarding setting is changed, but once
forwarding is turned on, we don't do the join for newly registered
devices. Fix from Li Wei.
3) Netfilter's NAT module autoload in ctnetlink drops a spinlock around
a sleeping call, problem is this code path doesn't actually hold that
lock. Fix from Pablo Neira Ayuso.
4) TG3 uses the wrong interfaces to hook into the new byte queue limit
support. It uses the device level interfaces, which is fine for
single queue devices, but on more recent chips this driver supports
multiqueue so we have to use the multiqueue BQL APIs. Fix from Tom
Herbert.
5) r8169 resume fix from Francois Romieu.
6) Add some cxgb4 device IDs, from Vipul Pandya.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
IPv6: Fix not join all-router mcast group when forwarding set.
caif-hsi: Set default MTU to 4096
cxgb4vf: Add support for Chelsio's T480-CR and T440-LP-CR adapters
cxgb4: Add support for Chelsio's T480-CR and T440-LP-CR adapters
mlx4_core: remove buggy sched_queue masking
netfilter: nf_conntrack: fix early_drop with reliable event delivery
bridge: netfilter: don't call iptables on vlan packets if sysctl is off
netfilter: bridge: fix wrong pointer dereference
netfilter: ctnetlink: remove incorrect spin_[un]lock_bh on NAT module autoload
netfilter: ebtables: fix wrong name length while copying to user-space
r8169: runtime resume before shutdown.
tcp: fix tcp_shift_skb_data() to not shift SACKed data below snd_una
tg3: Fix to use multi queue BQL interfaces
Default MTU for CAIF HSI was wrongly set to 15 * 4092 bytes.
The patch sets default MTU size to 4096.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a bug introduced by commit fe9a2603c, where the priority bits
in the schedule queue field were masked out.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
With runtime PM, if the ethernet cable is disconnected, the device is
transitioned to D3 state to conserve energy. If the system is shutdown
in this state, any register accesses in rtl_shutdown are dropped on
the floor. As the device was programmed by .runtime_suspend() to wake
on link changes, it is thus brought back up as soon as the link recovers.
Resuming every suspended device through the driver core would slow things
down and it is not clear how many devices really need it now.
Original report and D0 transition patch by Sameer Nanda. Patch has been
changed to comply with advices by Rafael J. Wysocki and the PM folks.
Reported-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 regression fix from Martin Schwidefsky:
"It is a fix for a regression that has been introduced with git commit
25f269f173 - "[S390] qdio: EQBS retry after CCQ 96" - and if possible
we would like to have working code for the fcp data router in 3.3."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] qdio: fix handler function arguments for zfcp data router
of this driver yet (there's some i.MX platforms which will use it).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZXaD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A simple fix that's obvious from inspection. There's no mainline
users of this driver yet (there's some i.MX platforms which will use
it)."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix mask parameter in da9052_reg_update calls
Fix tg3 to use BQL multi queue related netdev interfaces since the
device supports multi queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Reported-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is just one patch in here, a revert of a powerpc EHCI driver
patch that was reported to cause problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9VTXkACgkQMUfUDdst+ylV+wCg0LCngetBRR4J7Tu+fxfIBS00
z6YAni9fZFigFsapZqiypbSVrZ6FARQs
=g7Br
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB: revert a powerpc EHCI patch
There is just one patch in here, a revert of a powerpc EHCI driver
patch that was reported to cause problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "powerpc/usb: fix issue of CPU halt when missing USB PHY clock"
This contains one build fix for the powerpc udbg driver that was reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9VTK0ACgkQMUfUDdst+ykAGACeLDYE9U586NNUAGcHALtb6AtT
R1IAoK4NgsUvzxkp8XOlUYUar1DulcZB
=0xfn
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
tty: build fix for 3.3-rc6
This contains one build fix for the powerpc udbg driver that was reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/powerpc: early udbg consoles can't be modules
2 relate to the recently added drive replacement.
One causes read error in RAID10 to sometimes be retried indefinitely.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=93ms
-----END PGP SIGNATURE-----
Merge tag 'md-3.3-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Three fixes for md in 3.3-rc: Two relate to the recently added drive
replacement. One fixes the problem where a read error in RAID10 would
sometimes be retried indefinitely."
* tag 'md-3.3-fixes' of git://neil.brown.name/md:
md/raid10: fix assembling of arrays with replacement devices.
md/raid10: fix handling of error on last working device in array.
md/raid1: fix buglet in md_raid1_contested.
Merge the emailed seties of 19 patches from Andrew Morton
* akpm:
rapidio/tsi721: fix queue wrapping bug in inbound doorbell handler
memcg: fix mapcount check in move charge code for anonymous page
mm: thp: fix BUG on mm->nr_ptes
alpha: fix 32/64-bit bug in futex support
memcg: fix GPF when cgroup removal races with last exit
debugobjects: Fix selftest for static warnings
floppy/scsi: fix setting of BIO flags
memcg: fix deadlock by inverting lrucare nesting
drivers/rtc/rtc-r9701.c: fix crash in r9701_remove()
c2port: class_create() returns an ERR_PTR
pps: class_create() returns an ERR_PTR, not NULL
hung_task: fix the broken rcu_lock_break() logic
vfork: kill PF_STARTING
coredump_wait: don't call complete_vfork_done()
vfork: make it killable
vfork: introduce complete_vfork_done()
aio: wake up waiters when freeing unused kiocbs
kprobes: return proper error code from register_kprobe()
kmsg_dump: don't run on non-error paths by default
