Add channel 1 and 2 input mixer registers and the related ALSA mixer
controls for TAS5717/19 chips.
The mixer control coefficients on the chip are linear in the range
-3.99999 to +3.99999, encoded in 3.23 number format.
In this patch the mixer controls are limited to 128 values
from 0.0 to 1.0 in 1/64 steps.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo 100S netbook has a codec controller for which there is a
driver, but doesn't know how to access the device. This adds the
necessary ACPI table for the driver to find the device.
Device (TTLV)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "10TI3100") // _HID: Hardware ID
Name (_CID, "10TI3100") // _CID: Compatible ID
Name (_DDN, "TI TLV320AIC3100 Codec Controller ") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Jan Schmidt <jan@centricular.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver changes jack type detection interruption to non-clock archi-
tecture for less 1mW power saving. The architecture is called manual mode
jack detection. It has no hardware debounce, no jack type detection, but
only detecting jack insertion. After jack insertion, the driver will
switch to auto mode jack detection with internal clock which can detect
microphone, jack type and do hardware debounce.
The manual architecture has these main changes including codec initiation,
interruption, clock control, and power management. When codec initiation
or system resume, the clock is closed as jack insertion detection at man-
ual mode, and bypass debounce circuit. These configurations move to resume
setup function when setup bias level after resume.
When jack insertion detection happens, the manual mode turns off and make
configuration about jack type detection interruption at auto mode in auto
irq setup function which can detect microphone and jack type. The inter-
ruption will switch to manual mode again with clock free until jack ejec-
tion happens.
The system clock configuration adds clock disable option which can disable
internal VCO clock. Before the system clock change, there is an restric-
tion added to make sure clock disabled and not config any clock when no
headset connected.
In power management, we involve the solution about races and jack detec-
tion in resume from Ben Zhang in the following patch and list his comment.
[PATCH] ASoC: nau8825: Fix jack detection across suspend
"Jack plug status is rechecked at resume to handle plug/unplug
in S3 when the chip has no power."
"Suspend/resume callbacks are moved from the i2c dev_pm_ops to
snd_soc_codec_driver. soc_resume_deferred is a delayed work
which may trigger nau8825_set_bias_level. The bias change races
against dev_pm_ops, causing jack detection issues.
soc_resume_deferred ensures bias change and snd_soc_codec_driver
suspend/resume are sequenced correctly."
Change SAR widget to supply type which can prevent the codec keeping at
SND_SOC_BIAS_ON during suspend. The codec suspend function can just invoke
normally.
Before the system suspends, the driver turns off all interruptions. Keep
the interruption quiet before resume setup completes. The ADC channel will
be disabled which is needed for interruptions at audo mode.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add programmable biquad filter configuration control for user space.
The filter is configurable for low pass filters, high pass filters,
Notch filter, etc in the ADC and DAC path.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the suspend callback to accompany the existing resume operation.
With the suspend/resume callbacks the regmap (regcache) state handling can
follow the recommended sequence.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static checker warns:
Pointer 'hlink' returned from call to function 'snd_hdac_ext_bus_get_link'
at line may be NULL and will be dereferenced"
So we should always check the return of snd_hdac_ext_bus_get_link() before
referencing the link pointer
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
64-bit builds would generate a warning when we passed the core number as
a pointer through the notifier data:
sound/soc/codecs/cs47l24.c:1091:13: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
(void *)i);
Rather than just fix this up with more casting add a data structure that
holds information for the notifier chain. This will make it easier to
add additional information in the future as well.
Fixes: 7baa7e2490 ("ASoC: arizona: Add event notification on voice trigger events")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8758 chip is almost identical to WM8985 with the difference that it
doesn't feature the AUX input. This patch adds the WM8758 support into the
WM8985 driver.
The chip selection is done by the I2C name. The SPI probe supports only
the WM8985.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8758 chip is almost identical to WM8985 with the difference that it
doesn't feature the AUX input. This patch adds the register definitions
for WM8758 specific bit fields to the header file.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The datasheet uses decimal numbers for the register addresses, convert the
register values from hexadecimal to decimal and introduce macro for the
register definitions. This way it is easier to look up registers in the
documentation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TAS571x features multiple biquad filters. Their coefficients
are stored in 20-byte registers, which cannot be supported by
regmap.
This patch adds read and write functions for multi-word (32-bit) register
access and mixer controls for the biquads. The multi-word read/write
functions can be used in the future to implement other features like DRC or
output mixer.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform_driver does not need to set an owner as it will be
populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C driver has an i2c_device_id array but that information isn't
exported to the module using the MODULE_DEVICE_TABLE() macro. So the
module autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the module.
The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value of DAC channel select is reverse in codec.
For normal usage, switch the channel select when codec bootup.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt clock is gated by x1[10:8], one of them needs to be enabled
all the time for interrupts to happen. We change codec to enable ADC
because it's helpful to reduce playback pop noise.
Don't use force enable pin to enable ADC instead of ADC widget event.
That won't interfere DAPM operation and let bias work normally.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Decrease internal clock frequency for power saving when standby.
But clock divider needs restore when MCLK as system clock in playback.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In FLL calculation, increase VCO/DCO frequency for better performance.
Besides, have different register configuration according to fraction or not
when apply FLL parameters.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend FLL clock source selection. The source can be from MCLK, BCLK or FS.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a driver for the MAX9860 Mono Audio Voice Codec.
https://datasheets.maximintegrated.com/en/ds/MAX9860.pdf
This driver does not support sidetone since the DVST register field is
backwards with the mute near the maximum level instead of the minimum.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS53L30 is a Quad-Channel ADC from Cirrus Logic with an I2S/TDM DAI.
So this patch adds a codec driver for CS53L30 that includes 4-channel
24-bit recording and TDM mode supports.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP uses an IRQ to indicate data is available on the compressed
stream. For voice trigger use-cases the first such IRQ can be considered
an indication that the user has spoken the key phrase triggering the
firmware. Provide a means for the ADSP code to communicate back to the
calling driver whether an IRQ should be considered as trigger event or
not.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some situations the voice control firmware will by used
to only provide a trigger notification event. In this case a
compressed stream will not be opened by user-space, as such we
need to provide a virtual output to power on the DSP in this
use-case. This patch adds a virtual output 'DSP Voice Trigger'
that can be used for this, and a switch that lets it be connected
to the core when required.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent is for SYSCLK to be tied to all input and output widgets such
that it turns on whenever the chip is in use. It is not tied to the DRC
signal activity detect virtual outputs, whilst in practice this is
unlikely to cause an issue (as an input will likely also be powered up)
best to correct.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform_driver does not need to set an owner as it will be
populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Inform the notifier chain if the DSP recognises a voice trigger.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a notifier chain that can be used from the machine driver to catch
events generated by the CODEC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new
drivers. Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uNKQ
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new drivers.
Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support"
* tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
ALSA: hda - Fix headset mic detection problem for one Dell machine
spi: spi-ep93xx: Fix the PTR_ERR() argument
ALSA: hda/realtek - Add support for ALC295/ALC3254
ASoC: kirkwood: fix build failure
ALSA: hda - Fix headphone noise on Dell XPS 13 9360
ASoC: ak4642: Enable cache usage to fix crashes on resume
ASoC: twl6040: Disconnect AUX output pads on digital mute
ASoC: tlv320aic32x4: Properly implement the positive and negative pins into the mixers
rcar: src: skip disabled-SRC nodes
ASoC: max98371 Remove duplicate entry in max98371_reg
ASoC: twl6040: Select LPPLL during standby
ASoC: rsnd: don't use prohibited number to PDMACHCRn.SRS
ASoC: simple-card: Add pm callbacks to platform driver
ASoC: pxa: Fix module autoload for platform drivers
ASoC: topology: Fix memory leak in widget creation
ASoC: Add max98371 codec driver
ASoC: rsnd: count .probe/.remove for rsnd_mod_call()
ASoC: topology: Check size mismatch of ABI objects before parsing
ASoC: topology: Check failure to create a widget
ASoC: add support for TAS5720 digital amplifier
...
This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any
core code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QsAc
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any core
code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver"
* tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (177 commits)
ALSA: firewire-lib: change a member of event structure to suppress sparse wanings to bool type
sound: oss: Use setup_timer and mod_timer.
ASoC: hdac_hdmi: Remove the unused 'timeout' variable
ASoC: fsl_ssi: Fix channel slipping on capture (or playback) restart in full duplex.
ASoC: fsl_ssi: Fix channel slipping in Playback at startup
ASoC: fsl_ssi: Fix samples being dropped at Playback startup
ASoC: fsl_ssi: Save a dev reference for dev_err() purpose.
ASoC: fsl_ssi: The IPG/5 limitation concerns the bitclk, not the sysclk.
ASoC: fsl_ssi: Real hardware channels max number is 32
ASoC: pcm5102a: Add support for PCM5102A codec
ASoC: hdac_hdmi: add link management
ASoC: Intel: Skylake: add link management
ALSA: hdac: add link pm and ref counting
ALSA: au88x0: Fix zero clear of stream->resources
ASoC: rt298: Add DMI match for Broxton-P reference platform
ASoC: rt298: fix null deref on acpi driver data
ASoC: dapm: deprecate MICBIAS widget type
ALSA: firewire-lib: drop skip argument from helper functions to queue a packet
ALSA: firewire-lib: add context information to tracepoints
ALSA: firewire-lib: permit to flush queued packets only in process context for better PCM period granularity
...
The ak4642 driver is using a regmap cache sync to restore the
configuration of the chip on resume but (as Peter observed) does not
actually define a register cache which means that the resume is never
going to work and we trigger asserts in regmap. Fix this by enabling
caching.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Disconnect also the path to AUXL from the HF path during digital_mute to
avoid pop noise leakage to Line-out pads.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
The TLV320AIC32x4 has a very flexible mixer on the inputs to the ADCs. Each
mixer has an available set of available pins that can be connected to the
ADC positive and negative pins via three different resistor values. This
allows for configuration of differential inputs as well as doing level
manipulation between sources going into the mixers.
The current code only provides positive pins and I implemented the resistors
in an earlier patch. It turns out that it appears to more accurately model
what's happening to implement each of the pins as a MUX rather than on/off
switches and a mixer. This way each pin can be set to its desired resistor
value. Since there are no switches, the mixer is no longer necessary in the
DAPM path. I set the DAPM paths such that the "off" position of any of the
MUXes turns the path off.
This should allow for any input confiuration available on the codec.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some definitions to support the PCM5102A codec
by Texas Instruments.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Changes to original patch by Florian Meier:
* rebased (Makefile and Kconfig
* fixed checkpath errors (spaces, newlines)
* added dt-binding documentation
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Manage the hda idisp link using shiny new link APIs. We need to
keep link On while we probe and also hold the reference in runtime
resume and drop in suspend
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton-P reference platform also uses combo jack for audio
connector so we need to set codec pdata to use this based on DMI
match for this board.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACPI driver data can be NULL so we need to check that before
dereference the driver data.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the codec is in standby we do not need to keep the HPPLL active.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current checking for PLL 32KHz mode fails in driver code when
bypassing the PLL. This is due to an incorrect check of PLL
source type when 32KHz clock is provided. Removal of this check
resolves the issue.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This update changes the dividers used for ranges of input MCLK
frequencies, to improve PLL locking for a corner case when at edge
of MCLK frequency input divider range.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently PC counter is always synchronised to DAI which means that
when the DAI is disabled, features such as ALC calibration cannot
be executed successfully. This patch makes sure that when the DAI
is disabled, PC counter is set to free-running.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the codec is DAI clk slave, and the SRM feature of the PLL
is being used, the enabling of the DAI should occur only after
the PLL has locked to the incoming WCLK. This update adds checking
to the the DAI widget event, so it waits for SRM to lock. There is
also a timeout if that lock doesn't occur within a given time.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, when Codec is I2S master DAI clocks are continuously
generated even if all audio streams have stopped. To improve
efficiency, control of the DAI clocks for master mode have been
moved to a DAPM widget event so they're only enabled as required.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the ES8328 does support different rates for capture and
playback, only very limited combinations are supported (8kHz and 48kHz
or 8.0182kHz and 44.1kHz) with most rates required to be symmetric.
Instead of adding a lot of complexity for little gain, let's enforce
symmetric rates.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The values are the same for the DAC and ADC so remove the specific
values and use values with shifts.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a refactor in preparation for supporting more sample sizes which
has no functional change.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is always used along with ES8328_CONTROL1_ENREF so there is no
change in the generated code as a result of this fix.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADCCONTROL4 and DACCONTROL1 registers are similar but not identical,
with the DACCONTROL1 having each field starting one bit higher than
ADCCONTROL4.
Instead of introducing a magic shift, add new constants for the values
in ADCCONTROL4 and use a second variable to setup the ADC.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This ensures that the clock is setup after its frequency has been set;
the existing code in set_dai_fmt may be called before the clock rate has
been set resulting in an incorrect configuration.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds "DLGS7219" ACPI id for the codec.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Tested-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only polling jd status when rt5645->pdata.jd_invert is true.
However, it should be done at all time since there will be no
interrupt for jd if we press a headset button and remove the
headset at the same time.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If someone powers down the DSP core (through routing changes
say) whilst a compressed record is in progress we can end up
using a freed pointer to the buffer object. When a compressed
audio stream is triggered we attach it to a buffer on a physical
DSP. This patch adds a detach of the buffer from the stream when
the stream is freed or when the DSP is powered down which avoids
the situation where we use a buffer when it is no longer valid.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move wm_adsp_compr_attach and wm_adsp_compr_attached functions so they
will stay logically grouped with similar functions after some additional
changes.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We intended || here instead of &&. The original code potentially leads
to a NULL dereference.
Fixes: 2889099eb8 ('ASoC: hdac_hdmi: Register chmap controls and ops')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewd-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the arbitrary length TLV based binary
controls. This allows users to properly access controls that are
more than 512 bytes in length.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this patch, chmap controls are created and user space can
set the channel map.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support multichannel hdac hdmi driver registers with HDA
channel map framework. Channel count and channel slot verbs are
programmed by using the chmap helpers/ops. The channel
allocation is then programmed in the audio infoframe as per CEA
spec.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch parses ELD speaker allocation data block to find
sink's chmap capability.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS5720L/M device is a high-efficiency mono
Class-D audio power amplifier optimized for high transient power
capability to use the dynamic power headroom of small loudspeakers.
Its digital time division multiplexed (TDM) interface enables up to
16 devices to share the same bus.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a function to delete and free the contents of the alg_regions list.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure that the wm_adsp driver cleans up when the codec driver
is removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds a wm_adsp2_remove() function to ensure that memory
is freed when the driver is unloaded or shut down.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bits in the ARIZONA_CLOCK_CONTROL register only respond to writes of
a '1', a write of '0' is ignored. So there's no need to use update_bits.
We can do a simple write to set bits.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT298_CBJ_CTRL1(0x4f) bit 10 is needed for headset capture. It
will be turned off when "VREF" widget is on and be turned on when
bias level is ON. It is odd. And if "VREF" is turned on in bias
level is ON, RT298_CBJ_CTRL1(0x4f) bit 10 will be turned off.
This patch move the bit control from rt298_set_bias_level and
rt298_vref_event to rt298_jack_detect. So it will be turned on
once a jack is plugged in.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt298 need to reset AD filter and the ADC settings will take effort.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA doesn't know about all the different compressed audio formats,
so there is no interface to let userspace enumerate the formats that
are supported by the connected sink. Exporting the raw ELD bytes to
userspace allows an application to select the appropriate audio format
depending on the current capabilities of the connected HDMI sink device.
Usually userspace then just pretends to ALSA that the data is in one of
the raw 16-bit PCM audio formats and relies on the IEC controls to tell
the sink how to interpret the data.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting up an FLL in pseudo-fractional mode it is preferred
to use a lower FRATIO if possible to give a higher reference clock
frequency. This patch swaps the two loops in arizona_calc_fratio()
so that lower FRATIOs are tried first. The decrementing loop is also
changed to start from init_ratio because the original settings might
already give a fractional value for N.K
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input mixers support routing the IN1_R pin to the Left PGA and the
IN2_L pin to the Right PGA. This patch allows for those routings.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input pins of the aic3204 have resistors inline with them. The
current code assumes that you want a 10k resistor inline with your
inputs and implements it as a simple switch. This patch creates an enum
for each pin and allows you to switch between not connected, 10k, 20k
and 40k ohm values. This more closely models the acutal aic3204 part.
These pin settings are documented in TI's SLAA557 pages 135 and 136
(http://www.ti.com/lit/ml/slaa557/slaa557.pdf).
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320AIC32x4 series supports 96ksps rates in hardware. This patch
adds the necessary PLL divider values and clock settings to the table to
make 96ksps work.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo 100S netbook has a codec controller for which there is a
driver, but doesn't know how to access the device. This adds the
necessary ACPI table for the driver to find the device.
Device (TTLV)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "10TI3100") // _HID: Hardware ID
Name (_CID, "10TI3100") // _CID: Compatible ID
Name (_DDN, "TI TLV320AIC3100 Codec Controller ") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Jan Schmidt <jan@centricular.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL function was updated to disallow 32KHz in
commit 501f72e9c5 ("ASoC: da7219: Remove support for 32KHz PLL mode"),
but set_dai_sysclk() was missed and still permits it. This patch resolves
that discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for running the tlv32x4 control channel over SPI rather than I2C.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
To prepare for abstracting adding SPI support, the I2C pieces needs to
be in its own moudle. This patch moves common probe code into aic32x4_probe
and common removal code into aic32x4_remove. It also creates a static
regmap config structure to be copied in the I2C specific driver.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec's probe function is named aic32x4_probe. This is going to
conflict with later work to implement SPI support and separate out I2S
into its own file. In line with other drivers in the tree, this function
is renamed to aic32x4_codec_probe instead.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi-codec is a platform device driver to be registered from
drivers of external HDMI encoders with I2S and/or spdif interface. The
driver in turn registers an ASoC codec for the HDMI encoder's audio
functionality.
The structures and definitions in the API header are mostly redundant
copies of similar structures in ASoC headers. This is on purpose to
avoid direct dependencies to ASoC structures in video side driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We request one of the DSP IRQs during CODEC probe, as such we should
free it during CODEC remove, this patch does so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The thermal warning IRQs for the speaker are requested in CODEC probe
but never freed. This patch frees them in CODEC remove.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS47L24 and WM1831 codecs only use the OUT4L widget so we can
skip creation of the OUT4R widget.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we encounter an error on the DSP side whilst user-space is
waiting on the poll we should call snd_compr_fragment_elapsed,
although data is not actually available we want to wake
user-space such that the error can be propagated out
quickly. Additionally some versions of the DSP firmware are
not super consistent about actually generating an IRQ if they
encounter an error, as such we will check the DSP error status
every time we run out of available data as well, to ensure we
catch it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor out the reading of the DSP error flag into its own function to
support further improvements to the code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the system enters S3 during a playback, codec power needs to
be turned OFF during suspend and restored during resume. With
this patch the AFG node is set to D3 and codec power is turned
OFF during controller suspend call.
During resume, the codec power is left in ON state if the
playback was in progress while suspending.
Also setting power state for AFG node is optimized. With this the
loop with timeout is removed and codec_read is used instead.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_pm ops feature instead of soc pm as core assumes system
is capable of direct complete. Register with complete callback
instead of resume to synchronize with Jack notification from
display driver. This ensures correct Jack notification to user
space.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The list of TAS571x registers was incomplete.
Added the missing register definitions up to the register 0x25.
Added volatile and read-only register tables into tas5711_regmap_config
and tas5717_regmap_config.
The chip has 256 registers in total. But from address 0x29 on
(0x26 to 0x28 are reserved) the register width varies between
20, 12 and 8 bytes, which the register map cannot represent.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The chip selection was relying only on DT. It was not possible to use the
driver without DT.
This adds the chip type detection from the I2C name, which
allows to use the driver from the platform driver without DT.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that this is directly user selectable it needs to care about its
dependencies.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver did not have a mute function. The amplifier was brought out of
shutdown mode (hard-mute) once for ever in probe(), which was causing
clicks and pops when altering the I2C register configuration later.
This adds the digital_mute() function. The amplifier unmute in probe()
was removed.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cs47l24 supports the audio trace firmware, this streams of audio to be
captured from the CODEC over a compressed audio channel for
analysis/debugging of audio processing firmwares.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All other debug messages talk about data on the compressed stream in
bytes except avail which is shown in words. To avoid confusion show
avail in bytes as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Firstly, we should be locking the pwr_lock when we initialise the
compressed buffer. Secondly, fixup a couple of places when we should be
pulling pointers only under the pwr_lock as they may be affected by
operations that take that lock.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When trying to use simple card with wm8962 the following probe
error happens:
wm8962 0-001a: simple-card: set_sysclk error
asoc-simple-card sound: ASoC: failed to init 202c000.ssi-wm8962: -22
asoc-simple-card sound: ASoC: failed to instantiate card -22
asoc-simple-card: probe of sound failed with error -22
In simple-card.c the snd_soc_dai_set_sysclk() function is called with
clk_id as 0, which is an invalid clock for wm8962.
Adjust the clocks source definitions in wm8962.h so that the
simple card driver can work successfully.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable dspclk holds the rate of the DSPCLK, but the variable
sysclk holds an identifier for the clock. Currently if read a
non-sensical value from the DSPCLK_DIV register we assign sysclk to
dspclk, clearly this was intended to be sysclk_rate.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error message fits well into a single line.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When regulator_bulk_enable() fails inside wm8962_runtime_resume(),
we should disable the previously enabled clock.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a menu selection text so that users can enable, disable or
mark it as module in menuconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack plug status is rechecked at resume to handle plug/unplug
in S3 when the chip has no power.
Suspend/resume callbacks are moved from the i2c dev_pm_ops to
snd_soc_codec_driver. soc_resume_deferred is a delayed work
which may trigger nau8825_set_bias_level. The bias change races
against dev_pm_ops, causing jack detection issues.
soc_resume_deferred ensures bias change and snd_soc_codec_driver
suspend/resume are sequenced correctly.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Cc+v
-----END PGP SIGNATURE-----
Merge tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514"
* tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (291 commits)
ALSA: hda - Fix mutex deadlock at HDMI/DP hotplug
ALSA: ctl: change return value in compatibility layer so that it's the same value in core implementation
ALSA: mixart: silence an uninitialized variable warning
ALSA: usb-audio: Add sanity checks for endpoint accesses
ALSA: usb-audio: Minor code cleanup in create_fixed_stream_quirk()
ALSA: usb-audio: Fix NULL dereference in create_fixed_stream_quirk()
ALSA: hda - Limit i915 HDMI binding only for HSW and later
ALSA: hda - Fix unconditional GPIO toggle via automute
ALSA: mixart: silence unitialized variable warnings
ALSA: hda - Fixes double fault in nvhdmi_chmap_cea_alloc_validate_get_type
ALSA: intel8x0: Add clock quirk entry for AD1981B on IBM ThinkPad X41.
ALSA: hda - Add new GPU codec ID 0x10de0082 to snd-hda
ASoC: rsnd: add simplified module explanation
ASoC: hdac_hdmi: Add broxton device ID
ASoC: Intel: Bxtn: Add Broxton PCI ID
ASoC: Intel: Skylake: Move Skylake dsp ops & loader ops
ASoC: Intel: add dmabuffer to common sst_dsp
ASoC: Intel: Skylake: Unstatify skl_dsp_enable_core
ASoC: Intel: Skylake: Fix whitepsace issues
ASoC: Intel: Skylake: Move module id defines
...
this patch corrects the interface adc/dac control register definition
according to datasheet.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The rt5616 codec registers itself as an i2c driver, but can
be enabled even when i2c is turned off, which leads to a build
error:
codecs/rt5616.c:1419:1: error: data definition has no type or storage class [-Werror]
module_i2c_driver(rt5616_i2c_driver);
This adds an explicit Kconfig dependency, like the other codec
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 288bc356a8 ("ASoC: rt5616: allow to build with CONFIG_SND_SOC_RT5616")
Signed-off-by: Mark Brown <broonie@kernel.org>
This has been an extremely quiet release for the regulator API, aside
from bugfixes and small enhancements the only thing that really stands
out are the new drivers for Action Semiconductors ACT8945A, HiSilicon
HI665x, and the Maxim MAX20024 and MAX77620.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW58EWAAoJECTWi3JdVIfQMGMH/1v4ojMy0X/yPlFk/523u7uq
6ZJQ4zSTPyv0ccR+hsDjZ81BmM/vATrnQOllvTSwfnGMcs5amE3/9EhzdF5EciCB
8gUff/GfugXNqpVgpfYYfPhbQVTGllOFnZPmXsLx2dGlu094i69f4fZtoJCFlkmo
5c0L5Fnkt4w5XtFAA6ILuRtpwZ4jfJZ3VFKrtYwkgLcKw9GgSEqhVKvTPfkNqtjg
hzEl2P2K/Ug2uTqeZusKH30Sa1J7MW4B+C9dUVyTRB29+uA60y0foGTQjW9uCzEi
l1sqY9VDSKp9WwnshVrgVFViAhkrA7fWl4qaC/EDe7avvbh5SBpR/+gjZbmdRJU=
=jEl0
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been an extremely quiet release for the regulator API, aside
from bugfixes and small enhancements the only thing that really stands
out are the new drivers for Action Semiconductors ACT8945A, HiSilicon
HI665x, and the Maxim MAX20024 and MAX77620"
* tag 'regulator-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (46 commits)
regulator: pwm: Add support to have multiple instance of pwm regulator
regulator: pwm: Fix calculation of voltage-to-duty cycle
regulator: of: Use of_property_read_u32() for reading min/max
regulator: pv88060: fix incorrect clear of event register
regulator: pv88090: fix incorrect clear of event register
regulator: max77620: Add support to configure active-discharge
regulator: core: Add support for active-discharge configuration
regulator: helper: Add helper to configure active-discharge using regmap
regulator: core: Add support for active-discharge configuration
regulator: DT: Add DT property for active-discharge configuration
regulator: act8865: Specify fixed voltage of 3.3V for ACT8600's REG9
regulator: act8865: Rename platform_data field to init_data
regulator: act8865: Remove "static" from local variable
ASoC: cs4271: add regulator consumer support
regulator: max77620: Remove duplicate module alias
regulator: max77620: Eliminate duplicate code
regulator: max77620: Remove unused fields
regulator: core: fix crash in error path of regulator_register
regulator: core: Request GPIO before creating sysfs entries
regulator: gpio: don't print error on EPROBE_DEFER
...
gcc warns about the possibilty of accessing a property read from
devicetree in cs35l32_i2c_probe() when it has not been initialized
because CONFIG_OF is disabled:
sound/soc/codecs/cs35l32.c: In function 'cs35l32_i2c_probe':
sound/soc/codecs/cs35l32.c:278:2: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
The code is actually correct because it checks the dev->of_node
variable first and we know this is NULL here when CONFIG_OF
is disabled, but Russell King noticed that it's broken when
we probe the device using DT, and the properties are absent.
The code already has some checking for incorrect values, and
I keep that checking unchanged here, but add an additional
check for an error returned by the property accessor functions
that now gets handled the same way as incorrect data in the
properties.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
