In the IBSS auth TX debug message the BSSID and DA
address are reversed, fix that.
Signed-off-by: Sylvain Roger Rieunier <sylvain.roger.rieunier@gmail.com>
[reword commit message and make it fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whenever a host gets an AUTH frame it first allocates a new
station and then replies with another AUTH frame. However,
if sta allocations fails the host should send a DEAUTH frame
instead to tell the other end that something went wrong.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In IBSS it is possible that the supported rates set for a station changes over
time (e.g. it gets first initialised as an empty set because of no available
information about rates and updated later). In this case the driver has to be
notified about the change in order to update its internal table accordingly (if
needed).
This behaviour is needed by all those drivers that handle rc internally but
leave stations management to mac80211
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[Johannes - add docs, validate IBSS mode only, fix compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the auth frame registration count before sending
"open system" authentication messages when a new station
registers on a particular IBSS network. This stops us
from sending out multiple authentication messages with
different authentication algorithms.
Signed-off-by: Will Hawkins <hawkinsw@opentechinstitute.org>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211_can_beacon_sec_chan() to return true
if there is no secondary channel to simplify all the
current users of it. They all check the channel type
before calling the function because it returns false
if there's no secondary channel.
Also actually document the return value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the use of #ifdef CONFIG_MAC80211_IBSS_DEBUG/#endif
by adding a logging macro to encapsulate the test.
Convert the appropriate uses too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize the debugging to be able to use dynamic_debug.
Coalesce formats, align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This comment is deleted in the patch "mac80211: Advertise HT protection mode in
IEs". Moving the comment to the now corrected place.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize the net core ratelimited logging functions.
Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
The broken check leads to rate control attempting to use HT40 while
the driver is configured for HT20. This leads to interesting hardware
issues.
HT40 can only be used if the channel type is either HT40- or HT40+
and if the channel type of the cell matches the local type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since some of the HT code pre-dates 802.11n-2009
some names are wrong. The one that bothers me most
is that "HT operation" is called "HT information"
in our code and that causes confusion.
Rename "HT information" to "HT operation" and also
the control_chan field to primary_chan to match
the name used in the spec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some files implicitly get this via mesh.h
which itself doesn't need it, so move the
inclusion into the right files. Some other
files don't need it at all but include it,
so remove it from there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the IBSS network is RSN-protected, let userspace authorize the stations
instead of adding them as AUTHORIZED by default.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the future, when we start notifying drivers,
state transitions could potentially fail. To make
it easier to distinguish between programming bugs
and driver failures:
* rename sta_info_move_state() to
sta_info_pre_move_state() which can only be
called before the station is inserted (and
check this with a new station flag).
* rename sta_info_move_state_checked() to just
plain sta_info_move_state(), as it will be
the regular function that can fail for more
than just one reason (bad transition or an
error from the driver)
This makes the programming model easier -- one of
the functions can only be called before insertion
and can't fail, the other can fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit f1e3be1561.
Johannes Berg <johannes@sipsolutions.net> thinks that this patch is
incorrect. I'll defer to his judgment.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when we are on an IBSS network with no active station,
we would scan for other BSSID, even if fixed_bssid is on, due to
a bug in ibss.c, where fixed_channel would be checked instead of
fixed_bssid. This would trigger useless scans where scan results
would not be used anyway.
This patch also reverts commit 39d02a7d90,
which assumed that the ifibss->fixed_channel check was legitimate
to disable single-channel scans. IBSS single-channel scan should
now be fixed.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 13c40c5 ("mac80211: Add HT operation modes for IBSS") broke
ibss operation by mistakenly removing the local->oper_channel
update (causing ibss to start on the wrong channel). fix it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of a node re-joining the cell the sta_info structure belonging to it is
first destroyed and then reinserted. In this way its internal state is reset.
The joining operation is recognised thank the Auth frame being received.
This operation is helpful in case of a node being rebooted that is joining the
ad-hoc cell again, before its purge timeout on other nodes expires.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS mode, whenever a new station is added a 2-way authentication challenge
is performed. Actually this event can be used to recognise a new station joining
the cell even if its sta_info entry is already in the list.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Actually the DA field has already been checked along the rx path (in
prepare_for_handlers()) and this check is therefore useless at this point.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of authentication frame exchange between two IBSS STAs, the
DA field must contain the destinatioin address (instead of the BSSID).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we would have bailed out if 'ifibss->fixed_channel'
is valid i.e. we had used 'fixed-freq' parameter in iw ibss
join command. this is with the state 'IEEE80211_IBSS_MLME_JOINED'
so no need to check for it
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit a9b3cd7f32 (rcu: convert uses of rcu_assign_pointer(x, NULL) to
RCU_INIT_POINTER) did a lot of incorrect changes, since it did a
complete conversion of rcu_assign_pointer(x, y) to RCU_INIT_POINTER(x,
y).
We miss needed barriers, even on x86, when y is not NULL.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to notify drivers and simplify the station
management code, defer IBSS station insertion to a
work item and don't do it directly while receiving
a frame.
This increases the complexity in IBSS a little bit,
but it's pretty straight forward and it allows us
to reduce the station management complexity (next
patch) considerably.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Station entries can have various states, the most
important ones being auth, assoc and authorized.
This patch prepares us for telling the driver about
these states, we don't want to confuse drivers with
strange transitions, so with this we enforce that
they move in the right order between them (back and
forth); some transitions might happen before the
driver even knows about the station, but at least
runtime transitions will be ordered correctly.
As a consequence, IBSS and MESH stations will now
have the ASSOC flag set (so they can transition to
AUTHORIZED), and we can get rid of a special case
in TX processing.
When freeing a station, unwind the state so that
other parts of the code (or drivers later) can rely
on the transitions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our new return also created a memleak. The skb should be freed before
returning an error.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We recently introduced a new return here but it needs an unlock first.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HT mode is set by iw (previous patchsets).
The interface is set into the specified HT mode.
HT mode and capabilities are announced in beacons.
If we add a station that uses HT also, the fastest matching HT mode will
be used for transmission. That means if we are using HT40+ and we add a station
running on HT40-, we would transfer at HT20.
If we join an IBSS with HT40, but the secondary channel is not
available, we will fall back into HT20 as well.
Allow frame aggregation to start in IBSS mode.
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* remove implicit channel_type enum assumptions
* use rate_control_rate_init() if channel type changed
* remove channel flags check
* activate HT IBSS feature support
* slightly reword commit message
* rebase on wireless-testing
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Follow 802.11n-2009 9.13.3.1 for protection mode and ADDBA
* Send ADDBA only to HT STAs - implement 11.5.1.1 partially
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 should set carrier_on for ibss vifs
only while they are joined (similar to sta vifs)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.
Update all the drivers that implement these callbacks.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When assigning a NULL value to an RCU protected pointer, no barrier
is needed. The rcu_assign_pointer, used to handle that but will soon
change to not handle the special case.
Convert all rcu_assign_pointer of NULL value.
//smpl
@@ expression P; @@
- rcu_assign_pointer(P, NULL)
+ RCU_INIT_POINTER(P, NULL)
// </smpl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignacy reports that sometimes after leaving an IBSS
joining a new one didn't work because there still
were stations on the list. He fixed it by flushing
stations when attempting to join a new IBSS, but
this shouldn't be happening in the first case. When
I looked into it I saw a race condition in teardown
that could cause stations to be added after flush,
and thus cause this situation. Ignacy confirms that
after applying my patch he hasn't seen this happen
again.
Reported-by: Ignacy Gawedzki <i@lri.fr>
Debugged-by: Ignacy Gawedzki <i@lri.fr>
Tested-by: Ignacy Gawedzki <i@lri.fr>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
