Commit graph

418 commits

Author SHA1 Message Date
Jesse Brandeburg
713b3c9e4c e1000e: flush all writebacks before unload
The driver was not flushing all writebacks before unloading, possibly
causing memory to be written by the hardware after the driver had
reinitialized the rings.

This adds missing functionality to flush any pending writebacks and is
called in all spots where descriptors should be completed before the driver
begins processing.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-02-17 01:11:21 -08:00
Jesse Brandeburg
615b32af97 e1000e: check down flag in tasks
This change is part of a fix to avoid any tasks running while the driver is
exiting and deinitializing resources.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-02-17 00:45:06 -08:00
Jesse Brandeburg
4633427412 e1000e: tx_timeout should not increment for non-hang events
Currently the driver increments the tx_timeout counter (an error counter)
when simply resetting the part with outstanding transmit work pending.
This is an unnecessary count of an error, when all we should be doing is
just resetting the part and discarding the transmits.  With this change the
only increment of tx_timeout is when the stack calls the watchdog reset
function due to a true Tx timeout.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-02-08 01:10:17 -08:00
Linus Torvalds
d018b6f4f1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
  GRETH: resolve SMP issues and other problems
  GRETH: handle frame error interrupts
  GRETH: avoid writing bad speed/duplex when setting transfer mode
  GRETH: fixed skb buffer memory leak on frame errors
  GRETH: GBit transmit descriptor handling optimization
  GRETH: fix opening/closing
  GRETH: added raw AMBA vendor/device number to match against.
  cassini: Fix build bustage on x86.
  e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
  e1000e: update Copyright for 2011
  e1000: Avoid unhandled IRQ
  r8169: keep firmware in memory.
  netdev: tilepro: Use is_unicast_ether_addr helper
  etherdevice.h: Add is_unicast_ether_addr function
  ks8695net: Use default implementation of ethtool_ops::get_link
  ks8695net: Disable non-working ethtool operations
  USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
  vxge: Remember to release firmware after upgrading firmware
  netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
  ipsec: update MAX_AH_AUTH_LEN to support sha512
  ...
2011-01-14 13:25:30 -08:00
Bruce Allan
af667a29dd e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
Some minor comment errors and whitespace issues discovered while looking
into this are also addressed.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-01-14 02:06:23 -08:00
Bruce Allan
0d6057e48b e1000e: update Copyright for 2011
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-01-14 02:04:01 -08:00
Linus Torvalds
008d23e485 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
  Documentation/trace/events.txt: Remove obsolete sched_signal_send.
  writeback: fix global_dirty_limits comment runtime -> real-time
  ppc: fix comment typo singal -> signal
  drivers: fix comment typo diable -> disable.
  m68k: fix comment typo diable -> disable.
  wireless: comment typo fix diable -> disable.
  media: comment typo fix diable -> disable.
  remove doc for obsolete dynamic-printk kernel-parameter
  remove extraneous 'is' from Documentation/iostats.txt
  Fix spelling milisec -> ms in snd_ps3 module parameter description
  Fix spelling mistakes in comments
  Revert conflicting V4L changes
  i7core_edac: fix typos in comments
  mm/rmap.c: fix comment
  sound, ca0106: Fix assignment to 'channel'.
  hrtimer: fix a typo in comment
  init/Kconfig: fix typo
  anon_inodes: fix wrong function name in comment
  fix comment typos concerning "consistent"
  poll: fix a typo in comment
  ...

Fix up trivial conflicts in:
 - drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
 - fs/ext4/ext4.h

Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
2011-01-13 10:05:56 -08:00
Bruce Allan
77996d1d4c e1000e: add custom set_d[0|3]_lplu_state function pointer for 82574
82574 needs to configure Low Power Link Up (or LPLU) differently than
the other parts in the 8257x family supported by the driver.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 23:44:09 -08:00
Bruce Allan
31dbe5b4ac e1000e: power off PHY after reset when interface is down
Some Phys supported by the driver do not remain powered off across a reset
of the device when the interface is down, e.g. on 82571, but not on 82574.
This patch powers down (only when WoL is disabled) the PHY after a reset if
the interface is down and the ethtool diagnostics are not currently running.

The ethtool diagnostic function required a minor re-factor as a result, and
the e1000_[get|put]_hw_control() functions are renamed since they are no
longer static to netdev.c as they are needed by the ethtool diagnostics.
A couple minor whitespace issues were cleaned up, too.

Reported-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 23:44:09 -08:00
Bruce Allan
fe46f58fa6 e1000e: use either_crc_le() rather than re-write it
For the 82579 jumbo frame workaround, there is no need to re-write the CRC
calculation functionality already found in the kernel's ether_crc_le().

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 23:44:08 -08:00
Bruce Allan
e0dc4f1254 e1000e: properly bounds-check string functions
Use string functions with bounds checking rather than their non-bounds
checking counterparts, and do not hard code these boundaries.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 23:44:08 -08:00
Bruce Allan
482fed85e6 e1000e: convert calls of ops.[read|write]_reg to e1e_[r|w]phy
Cleans up the code a bit by using the driver-specific e1e_rphy and
e1e_wphy macros instead of the full function pointer variants.  Fix
a couple whitespace issue with two already existing calls to e1e_wphy.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 23:44:07 -08:00
Bruce Allan
dd93f95e92 e1000e: cleanup variables set but not used
The ICR register is clear on read and we don't care what the returned value
is when resetting the hardware so the icr variable(s) can be removed.  We
should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and
from e1000_get_phy_id_82571() (dump a debug message when it fails and when
an unknown Phy id is returned).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09 23:44:06 -08:00
Bruce Allan
b1cdfead0e e1000e: checkpatch warnings - braces
WARNING: braces {} are not necessary for any arm of this statement
WARNING: braces {} are not necessary for single statement blocks

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-24 21:31:49 -08:00
Bruce Allan
6480641eb7 e1000e: checkpatch error - open braces
ERROR: that open brace { should be on the previous line

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-24 21:30:46 -08:00
Bruce Allan
184125a389 e1000e: checkpatch error - trailing statements
ERROR: trailing statements should be on next line

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-24 21:29:34 -08:00
Bruce Allan
f0f1a172b2 e1000e: checkpatch error - macro panethesis
ERROR: Macros with complex values should be enclosed in parenthesis

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-24 21:28:18 -08:00
Michał Mirosław
0d0b16727f net: Fix drivers advertising HW_CSUM feature to use csum_start
Some drivers are using skb_transport_offset(skb) instead of skb->csum_start
for NETIF_F_HW_CSUM offload.  This does not matter now, but if someone
implements checksumming of encapsulated packets then this will break silently.

TSO output paths are left as they are, since they are for IP+TCP only
(might be worth converting though).

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 14:43:15 -08:00
Tejun Heo
23f333a2bf drivers/net: don't use flush_scheduled_work()
flush_scheduled_work() is on its way out.  This patch contains simple
conversions to replace flush_scheduled_work() usage with direct
cancels and flushes.

Directly cancel the used works on driver detach and flush them in
other cases.

The conversions are mostly straight forward and the only dangers are,

* Forgetting to cancel/flush one or more used works.

* Cancelling when a work should be flushed (ie. the work must be
  executed once scheduled whether the driver is detaching or not).

I've gone over the changes multiple times but it would be much
appreciated if you can review with the above points in mind.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: netdev@vger.kernel.org
2010-12-12 16:45:14 +01:00
Bruce Allan
c920aa8b87 e1000e: increment the driver version
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:57 -08:00
Bruce Allan
61c7581667 e1000e: static analysis tools complain of a possible null ptr p dereference
Adding this default case resolves the issue.

v2- Removed "break" in default case based on feedback

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:49 -08:00
Bruce Allan
e926244723 e1000e: minor error message corrections
Correct error messages when setting up Rx resources and when checking
module parameters.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:46 -08:00
Bruce Allan
36b973df71 e1000e: prevent null ptr dereference in e1000_tx_queue()
tx_desc can be dereferenced as a null pointer when count is passed in
as 0.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:41 -08:00
Bruce Allan
073287c037 e1000e: support new PBA format from EEPROM
Provide support to e1000e for displaying the new format of the PBA found
in the EEPROM.  The unique PBA identifier is no longer restricted to
hexadecimal numbers and must now be read and displayed as a string.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:37 -08:00
Bruce Allan
664dc878ed e1000e: 82579 PHY incorrectly identified during init
During init, reading the 2 PHY ID registers back-to-back in the default
fast mode could return invalid data (all F's) and in slow mode could
return data to the second read the data from the first read.  To resolve
the issue in fast mode, set to slow mode before any PHY accesses; to
resolve the issue in slow mode, put in a delay for every 82579 PHY access.
Since this PHY is currently only paired with the pch2lan MAC and the PHY
type is not known before the first PHY access which can fail this way,
check for this based on MAC-type.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:34 -08:00
Bruce Allan
ce54afd16d e1000e: 82577/8/9 mis-configured OEM bits during S0->Sx
The LPLU (Low Power Link Up) and Gigabit Disable bits (a.k.a. OEM bits)
were being configured incorrectly when device goes to D3 state.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:27 -08:00
Bruce Allan
d9c76f99c2 e1000e: 82571 Serdes can fail to get link
When link partner is sending continuous Config symbols, the 82571 Serdes
FIFO can overflow resulting in Invalid bit getting set.  To resolve this,
if Sync and Config bits are both 1 ignore the Invalid bit and restart
auto-negotiation.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:14 -08:00
Bruce Allan
cbd006cb7d e1000e: 82577/8 must acquire h/w semaphore before workaround
The workaround function e1000_configure_k1_pchlan() assumes the h/w
semaphore is already acquired.  This was originally missed when setting up
the part for the ethtool loopback test.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:11 -08:00
Bruce Allan
ed5c2b0b78 e1000e: 82574/82583 performance improvement
Increasing the transmit fifo by 4K (by decreasing the receive fifo size
specified in .pba by the same amount) increases Tx performance.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:08 -08:00
Bruce Allan
a82a14f4cd e1000e: 82571-based mezzanine card can fail ethtool link test
On certain 82571-based mezzanine NICs in some blade servers, the ethtool
link test can fail due to the serdes_has_link flag not set correctly.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:05 -08:00
Holger Eitzenberger
9633e63bb1 e1000e: fix double initialization in blink path
The kernel goes BUG() at the time 'ethtool -p eth0 3' comes
back, which is due to adapter->led_blink_task initialized
several times.  At the time it is still running this results
in a corrupted task_list of the associated workqueue.

The fix is to move the workqueue initialization to the
probe function instead.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10 22:13:01 -08:00
Jeff Kirsher
667445008d Intel Wired LAN drivers: Use static const
Based on work by Joe Perches <joe@perches.com>

Using static const to decrease data and overall object size.

CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
2010-12-10 22:12:32 -08:00
Ben Hutchings
ed4ba4b5b9 netdev: Use default implementation of ethtool_ops::get_link where possible
Various drivers are using implementations of ethtool_ops::get_link
that are equivalent to the default ethtool_op_get_link().  Change
them to use that instead.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-10 15:55:24 -08:00
Eric Dumazet
89bf67f1f0 drivers/net: use vzalloc()
Use vzalloc() and vzalloc_node() in net drivers

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-27 22:53:38 -08:00
Dongdong Deng
147b2c8cb4 e1000e: add netpoll support for MSI/MSI-X IRQ modes
With enabling CONFIG_PCI_MSI, e1000e could work in MSI/MSI-X IRQ mode,
and netpoll controller didn't deal with those IRQ modes on e1000e.

This patch add the handling MSI/MSI-X IRQ modes to netpoll controller,
so that netconsole could work with those IRQ modes.

Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-11-16 19:50:15 -08:00
Bruce Allan
1b98c2bb63 e1000e: 82574 intermittently fails to initialize with manageability f/w
The driver can fail initializing the hardware when manageability firmware
is performing concurrent MDIO operations because the hardware semaphore
scheme to prevent concurrent operations between software and firmware is
incorrect for 82574/82583.  Instead of using the SWSM register, the driver
should be using the EXTCNF_CTRL register.  A software mutex is also added
to prevent simultaneous software threads from performing similar concurrent
accesses.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-11-16 19:50:14 -08:00
Bruce Allan
d478eb44f7 e1000e: 82571 SerDes link handle null code word from partner
SerDes Link detection on certain 82571 mezzanine cards can fail when the
link is forced, the link partner does not recognize forced link and the
link partner sends null code words.  Detect the null code words and return
to auto-negotiation state which causes the link partner to begin responding
with valid code words.  Within a reasonable interval the link will finally
settle as forced by both partners.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-11-16 19:50:13 -08:00
Joe Perches
1d51c4185b drivers/net/e1000e: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-15 11:06:19 -08:00
Uwe Kleine-König
b595076a18 tree-wide: fix comment/printk typos
"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-11-01 15:38:34 -04:00
Carolyn Wyborny
affa9dfb04 e1000e: Add check for reset flags before displaying reset message
Some parts need to execute resets during normal operation.  This flag
check ensures that those parts reset without needlessly alarming the
user.  Other unexpected resets by other parts will dump debug info
and message the reset action to the user, as originally intended.

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-28 10:18:59 -07:00
Carolyn Wyborny
ff10e13cd0 e1000e: reset PHY after errors detected
Some errors can be induced in the PHY via environmental testing
(specifically extreme temperature changes and electro static
discharge testing), and in the case of the PHY hanging due to
this input, this detects the problem and resets to continue.
This issue only applies to 82574 silicon.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-28 10:18:59 -07:00
Jesse Gross
eab6d18d20 vlan: Don't check for vlan group before vlan_tx_tag_present.
Many (but not all) drivers check to see whether there is a vlan
group configured before using a tag stored in the skb.  There's
not much point in this check since it just throws away data that
should only be present in the expected circumstances.  However,
it will soon be legal and expected to get a vlan tag when no
vlan group is configured, so remove this check from all drivers
to avoid dropping the tags.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 01:26:52 -07:00
Jesse Gross
b738127dfb vlan: Rename VLAN_GROUP_ARRAY_LEN to VLAN_N_VID.
VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 01:26:50 -07:00
Carolyn Wyborny
c6ce3854f0 e1000e: Fix for offline diag test failure at first call
Move link test call to later in the offline sequence, move the
restore settings block to afterwards and add another reset to ensure
the hardware is in a known state afterwards.

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18 07:54:30 -07:00
Bruce Allan
828bac87bb e1000e: 82579 performance improvements
The initial support for 82579 was tuned poorly for performance.  Adjust the
packet buffer allocation appropriately for both standard and jumbo frames;
and for jumbo frames increase the receive descriptor pre-fetch, disable
adaptive interrupt moderation and set the DMA latency tolerance.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-30 18:00:17 -07:00
Jesse Brandeburg
3a3b758605 e1000e: use hardware writeback batching
Most e1000e parts support batching writebacks.  The problem with this is
that when some of the TADV or TIDV timers are not set, Tx can sit forever.

This is solved in this patch with write flushes using the Flush Partial
Descriptors (FPD) bit in TIDV and RDTR.

This improves bus utilization and removes partial writes on e1000e,
particularly from 82571 parts in S5500 chipset based machines.

Only ES2LAN and 82571/2 parts are included in this optimization, to reduce
testing load.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-30 17:59:31 -07:00
David S. Miller
e40051d134 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/qlcnic/qlcnic_init.c
	net/ipv4/ip_output.c
2010-09-27 01:03:03 -07:00
Eric Dumazet
807540baae drivers/net: return operator cleanup
Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-26 18:34:29 -07:00
Yi Zou
7b872a55c4 e1000/e1000e/igb/ixgb/ixgbe: set NETIF_F_HIGHDMA for VLAN feature flags
If the netdev->features is set with NETIF_F_HIGHDMA, we should set the
corresponding netdev->vlan_features as well to allow VLAN netdev created
on top of the real netdev to be able to also benefit from HIGHDMA on 32bit
system, reducing the performance hit that is caused by __skb_linearize(),
particularly for large send. This is fixed in this patch for all Intel e1000,
e1000e, igb, ixgbe, and ixgbe drivers since this should be beneficial
to all devices supported by these drivers.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-22 21:20:04 -07:00
Bruce Allan
605c82bab5 e1000e: 82579 do not gate auto config of PHY by hardware during nominal use
For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets.  This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-22 20:41:21 -07:00