PCI scan code calls the arch specific pcibios_fixup_bus() each time it scans a
new bridge. For root bridge hot-plug, the bridge and it's attached devices
may not have been configured properly yet, so it's not safe to claim those
resources at this time.
This code goes away when we clean up the way pci resources are claimed (in
pci_enable_device()), so this is only a stopgap fix.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When checking if a PCI to PCI bridge should be enabled to decode memory and/or
IO resources, we need to look at all device resources not just the first 6.
This is needed to allow PCI bridges to pass down memory and IO accesses to
child devices even when the bridge itself does not consume resources in its
PCI BARs.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When you hot-plug a (root) bridge hierarchy, it may have p2p bridges and
devices attached to it that have not been configured by firmware. In this
case, we need to configure the devices before starting them. This patch
separates device start from device scan so that we can introduce the
configuration step in the middle.
I kept the existing semantics for pci_scan_bus() since there are a huge number
of callers to that function.
Also, I have no way of testing the changes I made to the parisc files, so this
needs review by those folks. Sorry for the massive cross-post, this touches
files in many different places.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ia64 changes similar to kernel/sched.c.
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Acked-by: Paul Jackson <pj@sgi.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do some basic initial tuning.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dead CPU notifies online CPU that it's dead using cpu_state variable.
After switching to physical cpu hotplug, we forgot setting the variable.
This patch fixes it. Currently only __cpu_die uses it. We changed other
locations for consistency in case others use it.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(The i386 CPU hotplug patch provides infrastructure for some work which Pavel
is doing as well as for ACPI S3 (suspend-to-RAM) work which Li Shaohua
<shaohua.li@intel.com> is doing)
The following provides i386 architecture support for safely unregistering and
registering processors during runtime, updated for the current -mm tree. In
order to avoid dumping cpu hotplug code into kernel/irq/* i dropped the
cpu_online check in do_IRQ() by modifying fixup_irqs(). The difference being
that on cpu offline, fixup_irqs() is called before we clear the cpu from
cpu_online_map and a long delay in order to ensure that we never have any
queued external interrupts on the APICs. There are additional changes to s390
and ppc64 to account for this change.
1) Add CONFIG_HOTPLUG_CPU
2) disable local APIC timer on dead cpus.
3) Disable preempt around irq balancing to prevent CPUs going down.
4) Print irq stats for all possible cpus.
5) Debugging check for interrupts on offline cpus.
6) Hacky fixup_irqs() to redirect irqs when cpus go off/online.
7) play_dead() for offline cpus to spin inside.
8) Handle offline cpus set in flush_tlb_others().
9) Grab lock earlier in smp_call_function() to prevent CPUs going down.
10) Implement __cpu_disable() and __cpu_die().
11) Enable local interrupts in cpu_enable() after fixup_irqs()
12) Don't fiddle with NMI on dead cpu, but leave intact on other cpus.
13) Program IRQ affinity whilst cpu is still in cpu_online_map on offline.
Signed-off-by: Zwane Mwaikambo <zwane@linuxpower.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gcc4 doesn't like volatile casts as lvalues. Make the structure members
volatile instead.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is based on work by Carlos O'Donell and Matthew Wilcox. It
introduces/updates the compat_time_t type and uses it for compat siginfo
structures. I have built this on ppc64 and x86_64.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch includes IA64 architecture specific changes(ported form i386) to
support temporary disarming on reentrancy of probes.
In case of reentrancy we single step without calling user handler.
Signed-of-by: Anil S Keshavamurth <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Once the jprobe instrumented function returns, it executes a jprobe_break
which is a break instruction with __IA64_JPROBE_BREAK value. The current
patch checks for this break value, before assuming that jprobe instrumented
function just completed.
The previous code was not checking for this value and that was a bug.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current kprobes does not yet handle register kprobes on some of the
following kind of instruction which needs to be emulated in a special way.
1) mov r1=ip
2) chk -- Speculation check instruction
This patch attempts to fail register_kprobes() when user tries to insert
kprobes on the above kind of instruction.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current Kprobes when patching the original instruction with the break
instruction tries to retain the original qualifying predicate(qp), however
for cmp.crel.ctype where ctype == unc, which is a special instruction
always needs to be executed irrespective of qp. Hence, if the instruction
we are patching is of this type, then we should not copy the original qp to
the break instruction, this is because we always want the break fault to
happen so that we can emulate the instruction.
This patch is based on the feedback given by David Mosberger
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch_prepare_kprobes() was doing lots of functionality
in just one single function. This patch
attempts to clean up arch_prepare_kprobes() by moving
specific sub task to the following (new)functions
1)valid_kprobe_addr() -->> validate the given kprobe address
2)get_kprobe_inst(slot..)->> Retrives the instruction for a given slot from the bundle
3)prepare_break_inst() -->> Prepares break instruction within the bundle
3a)update_kprobe_inst_flag()-->>Updates the internal flags, required
for proper emulation of the instruction at later
point in time.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug where a kprobe still fires when the instruction is predicated
off. So given the p6=0, and we have an instruction like:
(p6) move loc1=0
we should not be triggering the kprobe. This is handled by carrying over
the qp section of the original instruction into the break instruction.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A cleanup of the ia64 kprobes implementation such that all of the bundle
manipulation logic is concentrated in arch_prepare_kprobe().
With the current design for kprobes, the arch specific code only has a
chance to return failure inside the arch_prepare_kprobe() function.
This patch moves all of the work that was happening in arch_copy_kprobe()
and most of the work that was happening in arch_arm_kprobe() into
arch_prepare_kprobe(). By doing this we can add further robustness checks
in arch_arm_kprobe() and refuse to insert kprobes that will cause problems.
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is required to support kprobe on branch/call instructions.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds IA64 architecture specific JProbes support on top of Kprobes
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is an IA64 arch specific handling of Kprobes
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As many of you know that kprobes exist in the main line kernel for various
architecture including i386, x86_64, ppc64 and sparc64. Attached patches
following this mail are a port of Kprobes and Jprobes for IA64.
I have tesed this patches for kprobes and Jprobes and this seems to work fine.
I have tested this patch by inserting kprobes on various slots and various
templates including various types of branch instructions.
I have also tested this patch using the tool
http://marc.theaimsgroup.com/?l=linux-kernel&m=111657358022586&w=2 and the
kprobes for IA64 works great.
Here is list of TODO things and pathes for the same will appear soon.
1) Support kprobes on "mov r1=ip" type of instruction
2) Support Kprobes and Jprobes to exist on the same address
3) Support Return probes
3) Architecture independent cleanup of kprobes
This patch adds the kdebug die notification mechanism needed by Kprobes.
For break instruction on Branch type slot, imm21 is ignored and value
zero is placed in IIM register, hence we need to handle kprobes
for switch case zero.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
From: Rusty Lynch <rusty.lynch@intel.com>
At the point in traps.c where we recieve a break with a zero value, we can
not say if the break was a result of a kprobe or some other debug facility.
This simple patch changes the informational string to a more correct "break
0" value, and applies to the 2.6.12-rc2-mm2 tree with all the kprobes
patches that were just recently included for the next mm cut.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It allows a selectable timer interrupt frequency of 100, 250 and 1000 HZ.
Reducing the timer frequency may have important performance benefits on
large systems.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This will at least suppress one prompt that users would have received the
first time they compile with the new DISCONTIG arch option. They'll still
get the "Memory Model" prompt, but 99% of them will have the default work
there.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For all architectures, this just means that you'll see a "Memory Model"
choice in your architecture menu. For those that implement DISCONTIGMEM,
you may eventually want to make your ARCH_DISCONTIGMEM_ENABLE a "def_bool
y" and make your users select DISCONTIGMEM right out of the new choice
menu. The only disadvantage might be if you have some specific things that
you need in your help option to explain something about DISCONTIGMEM.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch effectively eliminates direct use of pgdat->node_mem_map outside
of the DISCONTIG code. On a flat memory system, these fields aren't
currently used, neither are they on a sparsemem system.
There was also a node_mem_map(nid) macro on many architectures. Its use
along with the use of ->node_mem_map itself was not consistent. It has
been removed in favor of two new, more explicit, arch-independent macros:
pgdat_page_nr(pgdat, pagenr)
nid_page_nr(nid, pagenr)
I called them "pgdat" and "nid" because we overload the term "node" to mean
"NUMA node", "DISCONTIG node" or "pg_data_t" in very confusing ways. I
believe the newer names are much clearer.
These macros can be overridden in the sparsemem case with a theoretically
slower operation using node_start_pfn and pfn_to_page(), instead. We could
make this the only behavior if people want, but I don't want to change too
much at once. One thing at a time.
This patch removes more code than it adds.
Compile tested on alpha, alpha discontig, arm, arm-discontig, i386, i386
generic, NUMAQ, Summit, ppc64, ppc64 discontig, and x86_64. Full list
here: http://sr71.net/patches/2.6.12/2.6.12-rc1-mhp2/configs/
Boot tested on NUMAQ, x86 SMP and ppc64 power4/5 LPARs.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin J. Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SGI IOC4 I/O controller chip drivers are currently all configured by
CONFIG_BLK_DEV_SGIIOC4. This is undesirable as not all IOC4 hardware features
are needed by all systems.
This patch adds two configuration variables, CONFIG_SGI_IOC4 for core IOC4
driver support (see patch 1/3 in this series for further explanation) and
CONFIG_SERIAL_SGI_IOC4 to independently enable serial port support.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com>
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the bits to make the XPC code use the uncached
allocator rather than calling into the mspec driver. It also includes the
mspec.h header which is required to build the XPC modules.
Signed-off-by: Jes Sorensen <jes@wildopensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the ia64 uncached page allocator and the generic
allocator (genalloc). The uncached allocator was formerly part of the SN2
mspec driver but there are several other users of it so it has been split
off from the driver.
The generic allocator can be used by device driver to manage special memory
etc. The generic allocator is based on the allocator from the sym53c8xx_2
driver.
Various users on ia64 needs uncached memory. The SGI SN architecture requires
it for inter-partition communication between partitions within a large NUMA
cluster. The specific user for this is the XPC code. Another application is
large MPI style applications which use it for synchronization, on SN this can
be done using special 'fetchop' operations but it also benefits non SN
hardware which may use regular uncached memory for this purpose. Performance
of doing this through uncached vs cached memory is pretty substantial. This
is handled by the mspec driver which I will push out in a seperate patch.
Rather than creating a specific allocator for just uncached memory I came up
with genalloc which is a generic purpose allocator that can be used by device
drivers and other subsystems as they please. For instance to handle onboard
device memory. It was derived from the sym53c7xx_2 driver's allocator which
is also an example of a potential user (I am refraining from modifying sym2
right now as it seems to have been under fairly heavy development recently).
On ia64 memory has various properties within a granule, ie. it isn't safe to
access memory as uncached within the same granule as currently has memory
accessed in cached mode. The regular system therefore doesn't utilize memory
in the lower granules which is mixed in with device PAL code etc. The
uncached driver walks the EFI memmap and pulls out the spill uncached pages
and sticks them into the uncached pool. Only after these chunks have been
utilized, will it start converting regular cached memory into uncached memory.
Hence the reason for the EFI related code additions.
Signed-off-by: Jes Sorensen <jes@wildopensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of the code in arch/*/mm/hugetlbpage.c is quite similar. This patch
attempts to consolidate a lot of the code across the arch's, putting the
combined version in mm/hugetlb.c. There are a couple of uglyish hacks in
order to covert all the hugepage archs, but the result is a very large
reduction in the total amount of code. It also means things like hugepage
lazy allocation could be implemented in one place, instead of six.
Tested, at least a little, on ppc64, i386 and x86_64.
Notes:
- this patch changes the meaning of set_huge_pte() to be more
analagous to set_pte()
- does SH4 need s special huge_ptep_get_and_clear()??
Acked-by: William Lee Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the core of the (much simplified) early reclaim. The goal of this
patch is to reclaim some easily-freed pages from a zone before falling back
onto another zone.
One of the major uses of this is NUMA machines. With the default allocator
behavior the allocator would look for memory in another zone, which might be
off-node, before trying to reclaim from the current zone.
This adds a zone tuneable to enable early zone reclaim. It is selected on a
per-zone basis and is turned on/off via syscall.
Adding some extra throttling on the reclaim was also required (patch
4/4). Without the machine would grind to a crawl when doing a "make -j"
kernel build. Even with this patch the System Time is higher on
average, but it seems tolerable. Here are some numbers for kernbench
runs on a 2-node, 4cpu, 8Gig RAM Altix in the "make -j" run:
wall user sys %cpu ctx sw. sleeps
---- ---- --- ---- ------ ------
No patch 1009 1384 847 258 298170 504402
w/patch, no reclaim 880 1376 667 288 254064 396745
w/patch & reclaim 1079 1385 926 252 291625 548873
These numbers are the average of 2 runs of 3 "make -j" runs done right
after system boot. Run-to-run variability for "make -j" is huge, so
these numbers aren't terribly useful except to seee that with reclaim
the benchmark still finishes in a reasonable amount of time.
I also looked at the NUMA hit/miss stats for the "make -j" runs and the
reclaim doesn't make any difference when the machine is thrashing away.
Doing a "make -j8" on a single node that is filled with page cache pages
takes 700 seconds with reclaim turned on and 735 seconds without reclaim
(due to remote memory accesses).
The simple zone_reclaim syscall program is at
http://www.bork.org/~mort/sgi/zone_reclaim.c
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes handling of accesses to ar.rsc via ptrace & restore_sigcontext
[With Thanks to Chris Wright for noticing the restore_sigcontext path]
Signed-off-by: Matthew Chapman <matthewc@hp.com>
Acked-by: David Mosberger <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove "pci=routeirq" option for ia64. This was a workaround
after ACPI IRQ routing was changed from "all at boot for everything
in _PRT" to "do it when the device is enabled" in case there were
drivers that didn't use pci_enable_device().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The nested_dtlb_miss handler currently does not handle fault from
hugetlb address correctly. It walks the page table assuming PAGE_SIZE.
Thus when taking a fault triggered from hugetlb address, it would not
calculate the pgd/pmd/pte address correctly and thus result an incorrect
invocation of ia64_do_page_fault(). In there, kernel will signal SIGBUS
and application dies (The faulting address is perfectly legal and we
have a valid pte for the corresponding user hugetlb address as well).
This patch fix the described kernel bug. Since nested_dtlb_miss is a
rare event and a slow path anyway, I'm making the change without #ifdef
CONFIG_HUGETLB_PAGE for code readability. Tony, please apply.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
printk() calls should include appropriate KERN_* constant.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Allow the SGI simulator (medusa) to work on generic kernels. There is
no inherent dependency on an sn2-specific kernel.
Boot tested on Altix, medusa and HP rx2600.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Refresh arch/ia64/defconfig, as it was getting a bit stale. The only
manual changes I made were:
CONFIG_SCSI_SATA=y needed for some Altix base I/O cards
CONFIG_SCSI_SATA_VITESSE=y
CONFIG_DM_MULTIPATH=m the rest are already modules
CONFIG_FUSION_SPI=y new driver breakout
CONFIG_FUSION_FC=m
CONFIG_SGI_TIOCX=y enable some other SGI drivers
CONFIG_SGI_MBCS=m
CONFIG_AGP_SGI_TIOCA=m
Boot tested on Altix, HP rx2600 and Intel Tiger
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The latest assembler catches this typo. (reported by Jim Wilson).
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
current->blocked will be set to the value of current->thread_info->flags if the
cmpxchg to update thread_info->flags fails. For performance reasons the store into
current->blocked was placed in the cmpxchg loop. However, the cmpxchg overwrites the
register holding the value to be stored. In the rare case of a retry the value of
thread_info->flags will be written into current->blocked.
The fix is to use another register so that the register containing the current->blocked
value is not overwritten.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There've been reports of problems with CONFIG_PREEMPT=y and the high
floating point partition. This is caused by the possibility of preemption
and rescheduling on a different processor while saving or restioirng the
high partition.
The only places where the FPU state is touched are in ptrace, in
switch_to(), and where handling a floating-point exception. In switch_to()
preemption is off. So it's only in trap.c and ptrace.c that we need to
prevent preemption.
Here is a patch that adds commentary to make the conditions clear, and adds
appropriate preempt_{en,dis}able() calls to make it so. In trap.c I use
preempt_enable_no_resched(), as we're about to return to user space where
the preemption flag will be checked anyway.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
break.b does not store the break number in cr.iim, instead it stores 0,
which makes all break.b instructions look like BUG(). Extract the
break number from the instruction itself.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Christian Hildner pointed out that the comment did not match what the
code does in cpu_init() when we set up the default control register.
Patch based on suggestions from Ken Chen.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some bits of the kernel assume that gp always points to valid memory,
in particular PHYSICAL_MODE_ENTER() assumes that both gp and sp are
valid virtual addresses with associated physical pages. The IA64
module loader puts gp well past the end of the module, with no physical
backing. Offsets on gp are still valid, but physical mode addressing
breaks for modules. Ensure that gp always falls within the module
body. Also ensure that gp is 8 byte aligned.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix a bug in which shub_1_1_found is not being properly initialized or set,
resulting in the improper setting of sn_hub_info->shub_1_1_found.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This gets rid of an unused variable `error' in sys_ia32.c:sys32_epoll_wait()
Getting rid of this one makes parsing the output of the kernecomp
autobuild easier --- searching for `Error' to find a problem kept
hitting this one, even though it's only a warning.
Signed-off-by: Tony Luck <tony.luck@intel.com>
The attached patch cleans up a compilation warning when ACPI
is turned off (i.e., when compiling for the Ski simulator).
Signed-off-by: Tony Luck <tony.luck@intel.com>
