Fix bug in nvram write function. If the starting nvram address offset
happens to be the last dword of the page, the NVRAM_CMD_LAST bit will
not get set in the existing code. This patch fixes the bug by changing
the "else if" to "if" so that the last dword condition always gets
checked.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reset_phy parameter to tg3_reset_hw() and tg3_init_hw(). With
the full chip reset during MAC address change, the automatic PHY reset
during chip reset will cause a link down and bonding will not work
properly as a result. With this reset_phy parameter, we can do a chip
reset without link down when changing MAC address or MTU.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the full chip reset when changing MAC address if ASF is enabled.
ASF sometimes uses a different MAC address than the driver. Without
the reset, the ASF MAC address may be overwritten when the driver's
MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some PHY workaround code to reduce jitter on some PHYs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_carrier_off() call during tg3_phy_reset(). This is needed
to properly track the netif_carrier state in cases where we do a
PHY reset with interrupts disabled. The SerDes code will not run
properly if the netif_carrier state is wrong.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the nic initialization. If the nic was in low power
mode, it brings it back to normal power. Also, it utilizes a new
hardware reset during the init.
I am resending based on feedback, I corrected the register size mapping
and delay after posted write.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.
The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
airo cards with firmware versions of 5.30.17 and higher support WPA.
This patch recognizes WPA-capable firmware versions and adds support for
retrieving the WPA and RSN information elements from the card's scan
results. The JOB and FLAG fields are now independent, since there was
no space left in the FLAG field for FLAG_WPA_CAPABLE.
Signed-off-by: matthieu castet <castet.matthieu@free.fr>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ipw2200 scan completion event feature will cause a potential event
race condition in wpa_supplicant. The patch fixes this problem by move the
ipw_disassociate() to the IW_AUTH_WPA_ENABLED event handling code.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->last_noise is not used with the exponential averaging algorithm
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makefile both IPW2200_RADIOTAP and IPW2200_PROMISCUOUS depend on
IPW2200_MONITOR. Let IPW2200_PROMISCUOUS select IPW2200_RADIOTAP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added version string fields so the version string indicates what is
configured (ie, you'll see 1.1.1kpmd if you are using a GIT snapshot
(Kernel.. previously -git), promiscuous (p), monitor (m), debug (d) build.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch, a new promiscuous mode is enabled. If the module is loaded
with the rtap_iface=1 module parameter, two interfaces will be created
(instead of just one).
The second interface is prefixed 'rtap' and provides received 802.11 frames
on the current channel to user space in a radiotap header format.
Example usage:
% modprobe ipw2200 rtap_iface=1
% iwconfig eth1 essid MyNetwork
% dhcpcd eth1
% tcpdump -i rtap0
If you do not specify 'rtap_iface=1' then the rtap interface will
not be created and you will need to turn it on via:
% echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
You can filter out what type of information is passed to user space via
the rtap_filter sysfs entry. Currently you can tell the driver to
transmit just the headers (which will provide the RADIOTAP and IEEE
802.11 header but not the payload), to filter based on frame control
type (Management, Control, or Data), and whether to report transmitted
frames, received frames, or both.
The transmit frame reporting is based on a patch by Stefan Rompf.
Filters can be get and set via a sysfs interface. For example, set the
filter to only send headers (0x7), don't report Tx'd frames (0x10), and
don't report data frames (0x100):
% echo 0x117 > /sys/bus/pci/drivers/ipw2200/*/rtap_filter
All your packets are belong to us:
% tethereal -n -i rtap0
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects endian issues with the v3.0 fw image format.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch make ipw2200 generate the scan event every time a scan has
completed, so that user space know when to get fresh results.
Dan Williams would like to go towards this model in Network Manager
rather than having to poll.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch works with the ieee80211 stack to set the correct QoS bit to the
ipw2200 card. It fixed the TX failure problem for using WPA with QoS.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces sliding averaging by exponential averaging for
reporting the wireless statistics for signal and noise level for ipw2200.
See details from: http://www.ces.clemson.edu/linux/ipw2200_averages.shtml
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make all Orinoco PCI drivers (orinoco_pci, orinoco_plx, orinoco_tmd and
orinoco_nortel) as similar as possible. Use the best implementation of
error handling, the best error messages, the best comments.
Put common code to orinoco_pci.h. For now, it's suspend and resume
functions and function for registering the network device.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy PCI suspend/resume functions from orinoco_pci.c.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to identify the card before possible allocation problems,
so that the user at least can report the firmware version that fails.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After several days of operation of Netgear MA311 card, the card becomes
to seek improperly and needs reset. This patch tries to reset the card
when this situation occurs.
Mar 9 06:45:16 berkeley kernel: wlan0: Error -5 writing packet to BAP
Mar 9 06:45:16 berkeley kernel: hermes @ f992a000: BAP0 offset error: reg=0x4044 id=0x128 offset=0x44
Mar 9 06:45:16 berkeley kernel: wlan0: Error -5 writing packet to BAP
Mar 9 06:45:16 berkeley kernel: hermes @ f992a000: BAP0 offset error: reg=0x4044 id=0x128 offset=0x44
(etc.)
A more detailed description of the problem can be found at
https://bugzilla.novell.com/show_bug.cgi?id=154773
The same problem with different card is reported at
http://sourceforge.net/mailarchive/message.php?msg_id=14597046
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use skb_pull() to strip the addresses from the original packet. Don't
strip protocol bytes.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The result of orinoco_xmit() can be OK, dropped packet and busy
transmitter. Rename labels accordingly. Increment stats->tx_errors in
one place. Increment stats->tx_dropped - nobody is doing it for us.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hermes_bap_pwrite() supports odd-sized packets now. There is no
minimal packet size for 802.11. Also, hermes_bap_pwrite() supports
odd-sized packets now. This removes all reasons to pad the Tx data.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new function can write an odd number of bytes, thus making padding
unnecessary.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't ever return -errno from orinoco_xmit() - the network layer doesn't
expect it.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing Tx exception, only read data until addr1. Rename
hermes_tx_descriptor_802_11 to hermes_txexc_data since it's only used to
Tx exceptions. Reuse existing hermes_tx_descriptor structure. Remove
fields after addr1 - they are not read from the card.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sparse is much better at finding endianess issues than such visual cues.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCMCIA drivers would never be loaded if the CIS were wrong.
No other PCMCIA drivers validate CIS.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes PIO mode on the softmac bcm43xx
driver. (A dscape patch will follow).
It mainly fixes endianess issues.
This patch is tested on PowerPC32 and i386.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was doing arithmetics on a little-endian value.
Reported by Stelios Koroneos <stelios@stelioscellar.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ibmveth_printk() is only used to print the driver version when the module
initializes, which means on all machines as long as it's compiled in.
If it's really only needed for debugging, boot with loglevel=8, or get
it from dmesg instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes several bugs in the gianfar driver, including a major one
where spinlocks were horribly broken:
* Split gianfar locks into two types: TX and RX
* Made it so gfar_start() now clears RHALT
* Fixed a bug where calling gfar_start_xmit() with interrupts off would
corrupt the interrupt state
* Fixed a bug where a frame could potentially arrive, and never be handled
(if no more frames arrived
* Fixed a bug where the rx_work_limit would never be observed by the rx
completion code
* Fixed a bug where the interrupt handlers were not actually protected by
their spinlocks
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Folks,
This patch (against 2.6.17-rc1) converts the cassini driver to the
pci_iomap API that will do the right thing, so architectures like
PARISC can stop screaming about illegal usage of ioremap() on
non-cacheable regions.
Tested on 64bit PARISC kernel.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>
> The patch was badly wordwrapped. Please fix and resend.
>
OK, I've fixed the wrapping and removed the CONFIG_ARM restriction. I've also did my
best to modify the C style to conform to the comments.
I noticed that the patch is getting ignored by majordomo due to its size >100K.
Should it be broken up somehow to allow posting to the lists?
Signed-off-by: Dustin McIntire <dustin@sensoria.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Straighten up the AMD Au1xx0 Ethernet probing code, make it print out (and
store in the 'net_device' structure) the physical address of the controller,
not the KSEG1-based virtual. Make the driver also claim/release the 4-byte MAC
enable registers and assign to the Ethernet ports two consecutive MAC
addresses to match those that are printed on their stickers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In a short discussion with Benjamin Herrenschmidt he mentioned
that Marvell PHYs are powered down the same way as the other
ones we currently handle. Thus actually do that, hopefully
saving some power during suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The attached patch adds support for VLANs to the sis900 driver and bumps
the version number. It is based on an old (2003) patch for the 2.4
series by Hamid Hashemi Golpayegani. It applies on top of 2.6.16(.5).
I have one report that it works and behaves as intended.
Please review and consider for inclusion.
Signed-off-by: Daniele Venzano <venza@brownhat.org>
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct the base address of the Realtek RTL8019AS chip on the Toshiba RBTX4938
board -- this should make the driver work at least when CONFIG_PCI is enabled.
Signed-off-by: Yuri Shpilevsky <yshpilevsky@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In a short discussion with Benjamin Herrenschmidt he mentioned
that Marvell PHYs are powered down the same way as the other
ones we currently handle. Thus actually do that, hopefully
saving some power during suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The room for the names in bcm43xx_priv_wx_args[] are IFNAMSIZ long and
IFNAMSIZ is defined as 16, so the names in bcm43xx_priv_wx_args should
be 15 characters (16 including the trailing \0). This patch fixes that
for the "set_shortpreambl", "get_shortpreambl", "set_swencryption", and
"get_swencryption" private calls. Patch is against 2.6.17-rc1.
Signed-off-by: Erik Mouw <erik@harddisk-recovery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cleans up the bcm43xx sysfs code and makes it compliant
with the unwritten sysfs rules (at least I hope so).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "depends on" to make all bcm43xx driver options be listed
at the same level.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix printk format warnings:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:456: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:460: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:476: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:480: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:200: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:311: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:733: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Symbol firmware F3.91-71 has an additional word in the commsquality RID.
Extend the receiving buffer by one word to accomodate it.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2.6.17-rc1 changed the title for the entry CONFIG_NET_RADIO. I
personally disagree with this change and want it reverted. Patch for
2.6.17-rc1.
Rationale : WIRELESS_EXT is an invisible option. Therefore,
the only way for a user to enable it is via NET_RADIO. Some users need
to do that for out-of-tree drivers. Therefore it should be mentionned
in the title of the option.
Rationale2 : the option just below is called "Wireless
Extension API over RtNetlink". Some users may confuse this option for
the main "Wireless Extension" option. Therefore reverting this change
help disambiguate the relation between those two options.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send scan completion events to user space when a scan completes.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Airo firmware versions >= 5.30.17 send re-association events to the
driver that are currently unrecognized, causing spurious disassociation
events to be sent to user space. Loss of sync due to scan requests also
results in disassociation events sent to user space. This patch traps
those two events; suppressing sync-loss on scan, and sending the correct
association event on re-association notifications.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Seems there was a bit of a fix needed to due a bad merge in the legacy
receive path. Fixes a panic due to skb_over_panic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Recent patch was mismerged in the miitool path. e1000_media_type_copper
was being compared with the phy type instead of the media type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add the sourceforge project mailinglist to the contact information.
Bump version to 7.0.38-k2
Update copyright string with the new year.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Implement more efficient locking (avoid the lock) when checking for
a stopped queue. Also don't wake the queue unless the threshold is
reached to avoid queue on/off thrash.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Remove multi-descriptor support from legacy recieve path
Add memory usage efficiency by using more correct size descriptors for
small MTU sizes and optimize using LPE for <= 1522 byte frame sizes
An extra performance fix that effected our TCP window size growth
as a receiver. Set our initial buffer to be 128 bytes instead of 256
to prevent over-socket charge when truesize is computed in the stack.
old way: truesize = 256 + l1 = 256 + 1460 = 1716
new way: truesize = 128 + l1 = 128 + 1460 = 1588
The magic value that we can't cross is 1648.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Removal of unused rx_dropped counter.
Removed reference to E1000_CTRL_EXT_CANC which is no longer valid,
replaced with E1000_CTRL_EXT_INT_TIMER_CLR
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Made an adapter struct variable into a local (txb2b)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Esb2 link didn't return after wol disable. The code previously assumed
that writing reset to PHY_CTRL phy register turned the phy back on.
In the ESB2 phy case that didn't occur.
Add ESB2 to acquire/release_hw functions upon review it was
discovered that esb2 was skipped on these functions
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
remove DPRINTKs that were printing warnings about power management on
2.4 kernels. Since we really don't react differently these printk
statements are not needed. This code was originally added to fix
some compile time warnings that got fixed by newer kernels.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
From: Linus Walleij <triad@df.lth.se>
This patch enables support for ALi ISA bridges when we run the smcinit
code. It is needed to properly configure some Toshiba laptops.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the STIR421x case, when the firmware upload fails, we need to
unregister_netdev. Otherwise we hit a BUG on free_netdev(), if sysfs
is enabled.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Use pci_set_consistent_dma_mask in ixgb driver
[PATCH] sky2: bad memory reference on dual port cards
[PATCH] mv643xx_eth: Fix tx_timeout to only conditionally wake tx queue
[PATCH] mv643xx_eth: Always free completed tx descs on tx interrupt
[PATCH] net drivers: fix section attributes for gcc
[PATCH] remove drivers/net/hydra.h
[PATCH] drivers/net/via-rhine.c: make a function static
[netdrvr b44] trim trailing whitespace
[PATCH] b44: increase version to 1.00
[PATCH] b44: disable default tx pause
[PATCH] via-rhine: execute bounce buffers code on Rhine-I only
[PATCH] network: axnet_cs.c: add missing 'PRIV' in ei_rx_overrun
[PATCH] dlink pci cards using wrong driver
The ixgb driver is using pci_alloc_consistent, thus is should also use
pci_set_consistent_dma_mask. This allows the driver to work on SGI
systems.
In case of an error during probing it should also disable the device again.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sky2 driver will oops referencing bad memory if used on
a dual port card. The problem is accessing past end of
MIB counter space.
Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After resetting the hardware on a tx_timeout, call netif_wake_queue()
only if we have free tx descriptors.
Also, attempt to recover if mv643xx_eth_start_xmit() is called when
there are fewer free tx descriptors than expected.
The BUG_ON() call we are replacing was hit on a tx_timeout that
called netif_wake_queue(), indirectly via netif_device_attach(),
even though we did not have enough free tx descriptors.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the tx interrupt handler to free completed tx descriptors even
when NAPI is enabled. Otherwise, the tx queue would fill up resulting
in poor performance and "NETDEV WATCHDOG: <iface>: transmit timed out"
messages.
Signed-off-by: Brent Cook <bcook@bpointsys.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If CONFIG_HOTPLUG=n, gcc doesn't like some __initdata to be const (rodata)
and other __initdata not const, so make the non-const __initdata const.
gcc errors:
drivers/net/bnx2.c:66: error: version causes a section type conflict
drivers/net/starfire.c:338: error: version causes a section type conflict
drivers/net/typhoon.c:137: error: version causes a section type conflict
drivers/net/natsemi.c:241: error: version causes a section type conflict
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove drivers/net/hydra.h which is both unused and covered by a 4 clause
BSD licence (not by the UCB).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-By: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Disable default tx pause frame support.
The b44 controller has a bug that generates excessive tx pause
frames.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the problem of some Dlink cards picking the wrong
driver. It looks like these cards use Yukon 1 chipset, not Yukon 2.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The in-kernel Sangoma drivers are both not compiling and marked as BROKEN
since at least kernel 2.6.0.
Sangoma offers out-of-tree drivers, and David Mandelstam told me Sangoma
does no longer maintain the in-kernel drivers and prefers to provide them
as a separate installation package.
This patch therefore removes these drivers.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: fix typo in change count initialization
kconfig: recenter menuconfig
kconfig: revert conf behaviour change
kconfig: fix default value for choice input
kbuild: fix NULL dereference in scripts/mod/modpost.c
kbuild: fix mode of checkstack.pl and other files.
kbuild: rebuild initramfs if content of initramfs changes
kbuild: properly pass options to hostcc when doing make O=..
kbuild: modules_install for external modules must not remove existing modules
kbuild: fix make dir/
ver_linux: don't print reiser4progs version if none found
kbuild: mips: fix sed regexp to generate asm-offset.h
kbuild: fix building single targets with make O=.. single-target
kbuild: use relative path to -I
kbuild: fix unneeded rebuilds in drivers/net/chelsio after moving source tree
kbuild: fix unneeded rebuilds in drivers/media/video after moving source tree
kbuild: fix garbled text in modules.txt
Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.
IBM reported a problem on powerpc blades during ethtool self test that
was caused by the memory test taking excessively long. Config. cycles
are very slow on powerpc and the memory test can take more than 10
seconds to complete using config. cycles.
David Miller informed me that an earlier version of the patch caused
problems on sparc64 systems with built-in tg3 chips. This version
fixes the problem by excluding all SUN built-in tg3 chips from doing
MMIO SRAM access.
TG3_FLAG_EEPROM_WRITE_PROT is also set unconditionally when
TG3_FLG2_SUN_570X is set. This should be sane as all SUN chips are
built-in and do not require Vaux switching.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the TG3_FLAG_NO_{TX|RX}_PSEUDO_CSUM flags because they are not
very useful. This will free up some bits for new flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables support for the Sigmatel's STIR421x IrDA chip.
Once patched with Sigmatel's firmware, this chip "almost" follows the
USB-IrDA spec. Thus this patch is against irda-usb.[ch].
The code has been tested by Nick Fedchik on an STIR4210 chipset based
dongle.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch integrates the smcinit code into the smsc-ircc driver.
Some laptops have their smsc-ircc chip not properly configured by the
BIOS and needs some preconfiguration. Currently, this can be done from
userspace with smcinit, a utility that comes with the irda-utils
package. It messes with ioports and PCI settings, from userspace. Now
with this patch, if we happen to be on one of the known to be faulty
laptops, we preconfigure the chip from the driver.
Patch from Linus Walleij <triad@df.lth.se>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory leak (buf wasn't freed) spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set .name in netconsole's struct console to identify the
struct's owner.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes some uneeded rebuilds under drivers/net/chelsio after moving
the source tree. The makefiles used $(TOPDIR) for include paths, which
is unnecessary. Changed to use relative paths.
Compile tested, produces byte-identical code to the previous makefiles.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits)
Documentation: fix minor kernel-doc warnings
BUG_ON() Conversion in drivers/net/
BUG_ON() Conversion in drivers/s390/net/lcs.c
BUG_ON() Conversion in mm/slab.c
BUG_ON() Conversion in mm/highmem.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/ptrace.c
BUG_ON() Conversion in ipc/shm.c
BUG_ON() Conversion in fs/freevxfs/
BUG_ON() Conversion in fs/udf/
BUG_ON() Conversion in fs/sysv/
BUG_ON() Conversion in fs/inode.c
BUG_ON() Conversion in fs/fcntl.c
BUG_ON() Conversion in fs/dquot.c
BUG_ON() Conversion in md/raid10.c
BUG_ON() Conversion in md/raid6main.c
BUG_ON() Conversion in md/raid5.c
Fix minor documentation typo
BFP->BPF in Documentation/networking/tuntap.txt
...
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Goramo finally got PCI subsystem ID for their PCI200SYN card. The
attached patch adds support for it - cards with old EEPROM data
will emit a warning with URL for update tool.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the smc91x on the LogicPD PXA270 to
the smc91x driver.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Also cleans up some nearby whitespace problems.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: "__you_cannot_kzalloc_that_much" [drivers/net/arcnet/com90xx.ko] undefined!
We're trying to allocate negative amounts of memory..
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Undo commit 100c467330
MMIOs timeout more quickly that PCI config cycles and some
of these SRAM accesses can take a very long time, triggering
the MMIO limits on some sparc64 PCI controllers and thus
resulting in bus timeouts and bus errors.
Signed-off-by: David S. Miller <davem@davemloft.net>
The "3c59x: use mii_check_media" patch introduced a netif_carrier_off in
vortex_up. 10base2 stoped working because of this. This is removed.
Tx/Rx reset is back in vortex_up because the 3c900B-Combo stops working after
changing from half duplex to full duplex when Tx/Rx reset is done with
vortex_timer.
Also brought back some mii stuff to be sure that it does not break something
else.
Thanks to Pete Clements <clem@clem.clem-digital.net> for reporting and testing.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pre-2.6.16 patch "3c59x collision statistics fix" accidentally caused
vortex_error() to not run iowrite16(TxEnable, ioaddr + EL3_CMD) if we got a
maxCollisions interrupt but MAX_COLLISION_RESET is not set.
Thanks to Pete Clements <clem@clem.clem-digital.net> for reporting and testing.
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kconfig sanitized around drivers/net
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the unused DEV_RELEASE_PENDING flag, and move the DEV_SUSPEND flag
into the p_dev structure, and make use of it at the core level.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Most of the driver initialization isn't done in the .probe function, but in
the internal _config() functions. Make them return a value, so that .probe
can properly report whether the probing of the device succeeded or not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Handle the _modifying_ operation sm91c92_cs requires in
pcmcia_modify_configuration, so that the only remaining users
of pcmcia_release_configuration() are within the pcmcia core
module.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In all but one case, the suspend and resume functions of PCMCIA drivers
contain mostly of calls to pcmcia_release_configuration() and
pcmcia_request_configuration(). Therefore, move this code out of the
drivers and into the core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert the remaining drivers which use pcmcia_release_io or
pcmcia_release_irq, and remove the EXPORT of these symbols.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_disable_device(struct pcmcia_device *p_dev) performs the necessary
cleanups upon device or driver removal: it calls the appropriate
pcmcia_release_* functions, and can replace (most) of the current drivers'
_release() functions.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
gcc4 doesn't like us declaring a static function inside another
function. We can do away with this construct altogether and use
BUILD_BUG_ON() instead (idea from Andi Kleen.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Added code to check for invalid MAC address from eeprom or user input.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The comments concerning how the pcnet32 ethernet device driver selects
the MAC addr to use are incorrect. A recent patch (in the last 3 months)
changed how the code worked, but did not change the comments.
Side comment: the new behaviour is good; I've got a pcnet32 card which
powers up with garbage in the CSR's, and a good MAC addr in the PROM.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't bother testing for CONFIG_NET_CBUS ("NEC PC-9800 C-bus cards"); it went
out with the rest of PC98 subarch.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The natsemi chip can have a larger EEPROM attached than it itself uses for
configuration. This patch adds support for user space access to such an
EEPROM.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This enables TX checksum offloading for the spidernet driver by default.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the bonding master to specify its carrier state
based upon the state of the slaves. For 802.3ad, the bond is up if
there is an active, parterned aggregator. For other modes, the bond is
up if any slaves are up. Updates driver version to 3.0.3.
Based on a patch by jamal <hadi@cyberus.ca>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix section mismatches in acenic driver:
WARNING: drivers/net/acenic.o - Section mismatch: reference to .init.data:tigon2FwText from .text between 'acenic_probe_one' (at offset 0x2409) and 'ace_interrupt'
WARNING: drivers/net/acenic.o - Section mismatch: reference to .init.data:tigon2FwRodata from .text between 'acenic_probe_one' (at offset 0x2422) and 'ace_interrupt'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reduces the message level of the RX ram full messages
from err to debug to prevent spamming the console leaving it in the
logfiles though.
From: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Problems with link state detection have been reported several times in the
past months.
Denis Vlasenko did all the work tracking it down. Jeff Garzik suggested the
proper place for the fix.
When using the mii library, the driver needs to check mii->force_media
and set dev->state accordingly.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Initializing the b44 MAC & PCI functional blocks in the controller must
occur inside init_one(). This will allow access to the MAC registers.
The controller was being powered up in b44_open() which would not allow
access to the registers before ifconfig was up.
Philip Kohlbecher found this bug.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Skip the main timer code if interrupts are disabled in the full lock
state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.
IBM reported a problem on powerpc blades during ethtool self test
that was caused by the memory test taking excessively long. Config.
cycles are very slow on powerpc and the memory test can take more
than 10 seconds to complete using config. cycles. As a result, NETDEV
WATCHDOG can be triggered during self test and the chip can end up in
a funny state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to check the TG3_FLAG_40BIT_DMA_BUG flag in the workaround code
path instead of device flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some older bootcode in some devices may report 0 MAC address in
SRAM when booting up from low power state. This patch fixes the
problem by checking for a valid MAC address in SRAM and falling back
to NVRAM if necessary.
Thanks to walt <wa1ter@myrealbox.com> for reporting the problem
and helping to debug it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all occurences of 0xff.. in calls to function pci_set_dma_mask()
and pci_set_consistant_dma_mask() with the corresponding DMA_xBIT_MASK from
linux/dma-mapping.h.
Signed-off-by: Matthias Gehre <M.Gehre@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the assumption that pnp_register_driver() returns the number of devices
claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed encrypted of EAPOL frames from wlan#ap interface (hostapd). This
was broken when moving to use new frame control field defines in
net/ieee80211.h. hostapd uses Protected flag, not protocol version
(which was cleared in this function anyway). This fixes WPA group key
handshake and re-authentication.
http://hostap.epitest.fi/bugz/show_bug.cgi?id=126
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hostap_tx_encrypt() is used only inside hostap_80211_tx.c and there
are no plans to use it elsewhere in the future either, so let's make
it static. As a bonus, this should silence Coverity scanner from
complaining about bogus FORWARD_NULL case (CID: 274).
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCMCIA_SPECTRUM must select FW_LOADER.
Reported by "Alexander E. Patrakov" <patrakov@ums.usu.ru>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initial patch by David Woodhouse and Michael Marineau.
Locking fix by me.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This also includes a rewritten valuesave-stack.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should not make a difference, but be careful to not trash the register.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug was caused by the packing of the bcm43xx_dma and bcm43xx_pio
structures into a union.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This may workaround the XMIT ERRORs some people are getting.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the starting point to make the driver out-of-order-MMIO-stores safe.
There are more mmiowb() needed.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has a potential to fix the >1G bug. But I can not test that, yet.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems to me that the today's wireless-2.6 git contains bcm43xx which
does not free txb's correctly, if I understand it right.
Consider a situation where a txb with two skb's is sent down.
The dma_tx_fragment will save the pointer to meta->txb of the first
fragment. If fragments are freed in order, ieee80211_txb_free frees both
skb's when the first fragment is processed. This may result in reuse
of the second skb's memory.
This danger is rather remote, but it seems to me that the patch
below not only fixes the problem, but also makes the code simpler,
which is good, right?
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Note that the periodic work has to be started with initialized==1
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The proper fix for this is to move IRQ enabling to the end of
init_board. But this is nontrivial and needs to be done with care.
Stay with this cheap workaround for now.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless Ext update:
update we_version_source
set enc_capa
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the beginnings of ethtool support for bcm43xx.
It only implements get_drvinfo and get_link, but that's enough for
ifplugd to use ethtool to know whether we're associated or not and then
start or stop dhcp as necessary.
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Geographical restriction should become part of the 80211 stack,
so every driver does not have to duplicate it.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Import the bcm43xx driver from the upstream sources here:
ftp://ftp.berlios.de/pub/bcm43xx/snapshots/bcm43xx/bcm43xx-20060123.tar.bz2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle netif_carrier_{on,of} also if media is forced to 10baseT/100baseTx.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set the polling interval for media changes to 5 seconds if link is down and
60 seconds if link is up.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check for media changes and netif_carrier by using mii_check_media() if mii is
used.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jens Axboe <axboe@suse.de>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER] x_table.c: sem2mutex
[IPV4]: Aggregate route entries with different TOS values
[TCP]: Mark tcp_*mem[] __read_mostly.
[TCP]: Set default max buffers from memory pool size
[SCTP]: Fix up sctp_rcv return value
[NET]: Take RTNL when unregistering notifier
[WIRELESS]: Fix config dependencies.
[NET]: Fill in a 32-bit hole in struct sock on 64-bit platforms.
[NET]: Ensure device name passed to SO_BINDTODEVICE is NULL terminated.
[MODULES]: Don't allow statically declared exports
[BRIDGE]: Unaligned accesses in the ethernet bridge
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
zorro_module_init() used the device count to automatically unregister and
unload drivers that found no devices. That might have worked at one time,
but has been broken for some time because zorro_register_driver() returned
either a negative error or a positive count (never zero). So it could only
unregister on failure, when it's not needed anyway.
This functionality could be resurrected in individual drivers by counting
devices in their .probe() methods.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
dio_module_init() used the device count to automatically unregister and
unload drivers that found no devices. That might have worked at one time,
but has been broken for some time because dio_register_driver() returned
either a negative error or a positive count (never zero). So it could only
unregister on failure, when it's not needed anyway.
This functionality could be resurrected in individual drivers by counting
devices in their .probe() methods.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Philip Blundell <philb@gnu.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MODULE_PARM was actually breaking: recent gcc version optimize them out as
unused. It's time to replace the last users, which are generally in the
most unloved drivers anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I accidentally ended up with a config that set NET_RADIO off,
and NET_WIRELESS_RTNETLINK on, which blew up thus..
net/built-in.o: In function `do_setlink':net/core/rtnetlink.c:479: undefined reference to `wireless_rtnetlink_set'
net/built-in.o: In function `do_getlink':net/core/rtnetlink.c:521: undefined reference to `wireless_rtnetlink_get'
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: ne2k.c won't compile if pci_clone_list is const
f71e130966 which (amongst other things)
made pci_clone_list in ne2k-pci.c const causes the following compile error.
This patch reverses that portion of that changeset
drivers/net/ne2k-pci.c:123: error: pci_clone_list causes a section type
conflict
~/ gcc --version
gcc (GCC) 4.0.3 (Debian 4.0.3-1)
~/ dpkg gcc-4.0 | grep Version
Version: 4.0.3-1
Signed-Off-By: Horms <horms@verge.net.au
ne2k-pci.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
cee0890cc97247b6a9decd94f5dc0719ac8f0b1b
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the Ethernet controller integrated in the
Atmel AT91RM9200 SoC processor.
Changes since the previous submission (01/02/2006) are:
- Make use of the clk.h clock infrastructure.
- The multicast hash function is not crc32. [Patch by Pedro Perez]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
switch to ioremap()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
switch to ioremap()
Adrian Bunk:
The order of the hunks in the patch was slightly rearranged due to an
unrelated change in the driver.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't need to keep track of available buffers, it is simpler
to just compute the value (ala e1000). Don't need tes on link up
because should always have available buffers then.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't free transmit buffers until the whole set of transmit descriptors
has been marked as done. Otherwise, we risk freeing a skb before the
whole transmit is done.
This changes the transmit completion handling from incremental to a
two pass algorithm. First pass scans and records the start of the last
done descriptor, second cleans up until that point.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In the error case we call skge_rx_reuse twice. This is harmless
but unnecessary.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver was using dev_alloc_skb which reserves space for the
Ethernet header. This unnecessary and it should just use alloc_skb,
also by using GFP_KERNEL during startup it won't run into problems when
a user asks for a huge ring size or mtu and potentially drains the
reserved atomic pool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver aligns the header on the initial receive buffers, but
but doesn't on followon receive buffer allocations.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Transmit buffers are always freed with interrupts enabled (softirq),
so we can just call dev_kfree_skb.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unicast packets are shown as multicast, real multicast packets are missing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker (CID: 659, 660) spotted this resource leak on
PCI probe error path. Free private data structure if pci_enable_device()
fails.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 58) spotted this duplicated idx != 0
validation for unicast keys in prism2_ioctl_siwencodeext().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 452, 453, 454, 455, 456) spotted this
unlikely read overrun of CIS buffer. Abort if CISTPL_CONFIG or
CISTPL_MANFID would not fit in buffer.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 930) spotted this double free on error path
(allocation failure). Do not free these here since generic error path
will take care of this.
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 273) spotted this inconsequent NULL checking
(unconditionally dereferencing directly after checking for NULL
isn't a good idea). Return immediately to avoid this.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 59) noted that the call to prism2_hw_reset()
was dead code. Move prism2_hw_reset() call to a place where it is
actually executed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Observed problems when multiple processes request scans and subsequently
scan results. This causes a scan result request to hit card registers
before the scan is complete, returning an incomplete scan list and
possibly making the card very angry. Instead, cache the results of a
wireless scan and serve result requests from the cache, rather than
hitting the hardware for them.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number 2312 was used all over the place to refer to the card's
default MTU. Make it a #define and use that everywhere rather than the
number.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show the specific device that driver messages are about.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is version 20 of the Wireless Extensions. This is the
completion of the RtNetlink work I started early 2004, it enables the
full Wireless Extension API over RtNetlink.
Few comments on the patch :
o totally driver transparent, no change in drivers needed.
o iwevent were already RtNetlink based since they were created
(around 2.5.7). This adds all the regular SET and GET requests over
RtNetlink, using the exact same mechanism and data format as iwevents.
o This is a Kconfig option, as currently most people have no
need for it. Surprisingly, patch is actually small and well
encapsulated.
o Tested on SMP, attention as been paid to make it 64 bits clean.
o Code do probably too many checks and could be further
optimised, but better safe than sorry.
o RtNetlink based version of the Wireless Tools available on
my web page for people inclined to try out this stuff.
I would also like to thank Alexey Kuznetsov for his helpful
suggestions to make this patch better.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for new chip 5755 which is very similar to 5787.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the tx producer and consumer fields in separate cache lines in
the device structure, similar to the VJ net channel queue structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine two small (56 byte and 320 byte) pci consistent memory
allocations into one allocation. Jeff Garzik suggested to store
the combined size in the bp structure for later use when freeing
the memory.
Use kzalloc() instead of kmalloc() + memset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some link-related problems by doing a coalesce_now after link
change interrupt to flush out the transient link status.
To facilitate this, the host coalesce cmd register value is cached in
the device structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hi,
this fixes coverity bug #888, where the variable
dev is used uninitialized. I assume the programmer
meant to use mdev, which is initialized.
Compile tested only.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
this fixes coverity bug #912, where skb is freed first,
and dereferenced a few lines later with skb->len.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch is required to get a SIS964 based motherboard ethernet working (FSC D1875)
(picking the #1 transceiver, instead of the last one, in case no known ones were found
might be a better default, and would have worked in this case too)
Signed-off-by: Artur Skawina <art_k@o2.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With Au1xx0 Ethernet driver, TX bytes/packets always remain zero. The
problem seems to be that when packet has been transmitted, the length word
in DMA buffer is zero.
The patch updates the TX stats when a buffer is fed to DMA. The initial
2.4 patch was posted to linux-mips@linux-mips.org by Thomas Lange 21 Jan
2005.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some PHYs should not be powered down in tg3_set_power_state() because
of bugs or other hardware limitations.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5700 and 5701 will not return correct SRAM data when the chip is in
D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device
in D0 before reading SRAM.
Thanks to Thomas Chenault at Dell for noticing this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Lennert Buytenhek
Move the uengine loader from arch/arm/mach-ixp2000 to arch/arm/common
so that ixp23xx can use it too.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- undo some Lindent damage by indenting member names
- remove history at top of .c file, this is stored in the kernel
repo changelog (in greater detail, even).
drivers/net/skfp/fplustm.c: In function `enable_formac':
drivers/net/skfp/fplustm.c:552: warning: large integer implicitly truncated to unsigned type
drivers/net/skfp/fplustm.c:555: warning: large integer implicitly truncated to unsigned type
These arguments were changed to `const', so the compiler can now see that it's
doing and outw(..., 0xffffnnnn). Cast the arg to ushort.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All accessor's different methods are now selected with C code and unused
ones statically optimized away at compile time instead of being selected
with #if's and #ifdef's. This has many advantages such as allowing the
compiler to validate the syntax of the whole code, making it cleaner and
easier to understand, and ultimately allowing people to define
configuration symbols in terms of variables if they really want to
dynamically support multiple bus configurations at the same time (with
the unavoidable performance cost).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Boards with multiple PHYs were not being handled properly by the pcnet32
driver. This patch by Thomas Bogendoerfer with changes by me will allow
Allied Telesyn 2700FTX and 2701FTX boards to use either the copper or
the fiber interfaces. It has been tested on ia32 and ppc64 hardware.
Philippe Seewer also tested and improved the patch.
ethtool for pcnet32 already supports multiple phys.
See also bugzilla bug 4219.
Please apply to 2.6.16
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware has additional error trap interrupt bits. I have never seen
them trigger, but if they do, it looks like this might be useful.
Signed-off-by: Stephen Hemminger <shemminger@osdl.rog>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch decodes state and revovers from any races in the transmit
timeout and NAPI logic. It should never trigger, but if it does then
do the right thing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change default coalescing parameters slightly, and allow wider
range of values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Redo the interupt handling of sky2 driver based on the IRQ mangement
documentation. All interrupts are handled by the device0 NAPI poll
routine.
Don't need to adjust interrupt mask in IRQ context, done only when
changing device under RTNL. Therefore don't need hwlock anymore.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove wake on lan support for now. It doesn't work right, and I
don't have a machine with working suspend/resume to test or fix it.
It will be re-enabled later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon EC/rev0 (A1) chipset requires a bunch of workarounds. I copied these
from sk98lin. But since they never got tested and add more cruft to the code;
any attempt at using driver as is on this version will probably fail.
It looks like this was a early engineering sample chip revision, if it ever shows
up on a real system. Produce an error message.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When I/O is non-cache-coherent, we need to ensure that the I/O buffers
we use don't share cache lines with other data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reformat some code to make it easier to read. And whitespace
fixes.
Signed-off-by: Stephen Hemminger <sheminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add mmio barriers at the appropriate places, don't have a platform
that needs them, but this is where the documentation of the patch
says to add them.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup of the part of the code that sets up DMA configuration.
Should cause no real change in operation, just clearer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SysKonnect Genesis and Yukon chip sets have restrictions on the possible
control block area. The memory needs to not cross 4 Gig boundary, and it needs
to be 8 byte aligned. This patch checks and fails to bring the device up
if region is unacceptable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve performance of skge driver by not touching irq mask
register as much. Since the interrupt source auto-masks, the driver
can just leave it disabled until the end of the soft irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup transmit buffers using NAPI. This allows the transmit routine
to leave interrupts enabled, and that improves performance.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes the needlessly global function tg3_request_irq()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're now starting to have quite a number of places that do skb_pull
followed immediately by an skb_postpull_rcsum. We can merge these two
operations into one function with skb_pull_rcsum. This makes sense
since most pull operations on receive skb's need to update the
checksum.
I've decided to make this out-of-line since it is fairly big and the
fast path where hardware checksums are enabled need to call
csum_partial anyway.
Since this is a brand new function we get to add an extra check on the
len argument. As it is most callers of skb_pull ignore its return
value which essentially means that there is no check on the len
argument.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the netif_carrier_off() call from tg3_init_one()->
tg3_init_link_config() to tg3_open() as is the convention for most other
network drivers.
I was getting a panic after a tg3 device failed to initialize due to DMA
failure. The oops pointed to the link watch queue with spinlock debugging
enabled. Without spinlock debugging, the Oops didn't occur.
I suspect that the link event was getting queued but not executed until
after the DMA test had failed and the device was freed. The link event was
then operating on freed memory, which could contain anything. With this
patch applied, the Oops no longer occurs.
[ Based upon feedback from Michael Chan, we move netif_carrier_off()
to the end of tg3_init_one() instead of moving it to tg3_open() -DaveM ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In latest -mm sbni gives following warning: WARNING:
drivers/net/wan/sbni.o - Section mismatch: reference to \ .init.data:
from .text between 'init_module' (at offset 0x14ef) and \
'cleanup_module'
The warning is caused by init_module() calling a function declared
__init. Declare init_module() __init too to fix warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semaphore to mutexes conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semaphore to mutexes conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODULE_PARM() is deprecated and is about to go away altogether.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the old __dev_put macro that is just a hold over from pre 2.6
kernel. And turn dev_hold into an inline instead of a macro.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some nvram related cleanup:
1. Add a tg3_nvram_read_swab() since swabing the data is frequently
done.
2. Add a function to convert nvram address to physical address
instead of doing it in 2 separate places.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool memory test on 5787 requires a new memory table.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support one-shot MSI on 5787.
This one-shot MSI idea is credited to David Miller. In this mode, MSI
disables itself automatically after it is generated, saving the driver
a register access to disable it for NAPI.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support ipv6 tx csum on 5787 by setting NETIF_F_HW_CSUM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support 5787 hardware TSO using a new flag TG3_FLG2_HW_TSO_2.
Since the TSO interface is slightly different and these chips have
finally fixed the 4GB DMA problem and do not have the 40-bit DMA
problem, a new hard_start_xmit is used for these chips. All previous
chips will use the old hard_start_xmit that is now renamed
tg3_start_xmit_dma_bug().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support additional nvrams and new nvram format for 5787 and 5754.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch turns the RTNL from a semaphore to a new 2.6.16 mutex and
gets rid of some of the leftover legacy.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here goes a patch for supporting TOIM3232 based serial IrDA dongles.
The code is based on the tekram dongle code.
It's been tested with a TOIM3232 based IRWave 320S dongle. It may work
for TOIM4232 dongles, although it's not been tested.
Signed-off-by: David Basden <davidb-irda@rcpt.to>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix-up tg3_get_ringparam() to return the correct parameters.
Set the jumbo rx ring parameter only if it is supported by the chip
and currently in use.
Add missing value for tx_max_pending, noticed by Rick Jones.
Update version to 3.51.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing netif_running() checks in tg3's dev->set_multicast_list()
and dev->set_mac_address(). If not netif_running(), these 2 calls can
simply return 0 after storing the new settings if required.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts 2 IrDA drivers pci_module_init() calls to
pci_register_driver().
Signed-off-by: Christophe Lucas <clucas@ifrance.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the deprecated sti/cli routines with the corresponding
spin_lock ones.
Signed-off-by: David chosrova <david.chosrova@libertysurf.fr>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simply adds support for a variation of the nsc-ircc PC8739x
chipset, found in some IBM Thinkpad laptops.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings the nsc-ircc code to a more up to date power
management scheme, following the current device model.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables PnP support for the nsc-ircc chipset.
Since we can't fetch the chipset cfg_base from the PnP layer, we just use
the PnP information as one more hint when probing the chip.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include <linux/vmalloc.h> so that it compiles properly on all archs.
Update version to 1.4.38.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to 1.4.37.
Add missing flush_scheduled_work() in bnx2_suspend as noted by Jeff
Garzik.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support bigger rx ring sizes (up to 1020) in the rx fast path.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase maximum receive ring size from 255 to 1020 by supporting
up to 4 linked pages of receive descriptors. To accomodate the
higher memory usage, each physical descriptor page is allocated
separately and the software ring that keeps track of the SKBs and the
DMA addresses is allocated using vmalloc.
Some of the receive-related fields in the bp structure are re-
organized a bit for better locality of reference.
The max. was reduced to 1020 from 4080 after discussion with David
Miller.
This patch contains ring init code changes only. This next patch
contains rx data path code changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the rx code path that does not handle the full rx ring correctly.
When the rx ring is set to the max. size (i.e. 255), the consumer and
producer indices will be the same when completing an rx packet. Fix
the rx code to handle this condition properly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate some of the registers in ethtool register test to reduce
driver size.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support WoL during shutdown by calling
tg3_set_power_state(tp, PCI_D3hot) during tg3_close().
Change the power state parameter to pci_power_t type and use
constants defined in pci.h.
Certain ethtool operations cannot be performed after tg3_close()
because the device will go to low power state. Add return -EAGAIN
in such cases where appropriate.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable TSO by default on newer chips that support TSO in hardware.
Leave TSO off by default on older chips that do firmware TSO because
performance is slightly lower.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't read from free'd memory after calling netif_rx(). docopy is used as
a boolean (0 and 1) so unsigned int is sufficient.
Coverity bug #928
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
platform_get_irq*() now returns on -ENXIO when the resource cannot be
found. Ensure all users of platform_get_irq*() handle this error
appropriately.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Fix 2 bugs in huge page support.
[SPARC64]: CONFIG_BLK_DEV_RAM fix
[SPARC64]: Optimized TSB table initialization.
[SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build.
[SPARC64]: Use SLAB caches for TSB tables.
[SPARC64]: Don't kill the page allocator when growing a TSB.
[SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set.
[SPARC64]: Increase top of 32-bit process stack.
[SPARC64]: Top-down address space allocation for 32-bit tasks.
[SPARC64] bbc_i2c: Fix cpu check and add missing module license.
[SPARC64]: Fix and re-enable dynamic TSB sizing.
[SUNSU]: Fix missing spinlock initialization.
[TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.
[SPARC64]: First cut at VIS simulator for Niagara.
[SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check.
[SPARC64]: Add SMT scheduling support for Niagara.
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
[SPARC64]: Move over to sparsemem.
[SPARC64]: Fix new context version SMP handling.
...
Sun does't put an SEEPROM behind the tigon3 chip, among other things,
so accesses to these areas just give bus timeouts.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.
For example, some 4-port card or mother board designs have 5704 behind
the 5714.
All devices behind the EPB require the 40-bit DMA workaround.
Thanks to Chris Elmquist again for reporting the problem and testing
the patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
semaphore to mutexes conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build-tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix gcc warning: ipw2100.c:2460: ISO C90 forbids mixed declarations and code
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Andrea Merello <andreamrl at tiscali it>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a big array overun found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies the driver to support the ipw2200-fw-3.0 image format.
The 3.0 fw image does not add any new capabilities, but as a result of
image format changes, it should fix two problems experienced by users:
1) Race conditions with the request_firmware interface and udev/hotplug
are improved as only a single request_firmware call is now required to
load the firmware and microcode (vs. 3 separate calls previously)
2) The monitor mode firmware (sniffer) is now packaged with the correct
boot image so it can now function without frequent restarts.
Note: Once you apply this patch, you will also need to upgrade your
firmware image to the 3.0 version available from:
http://ipw2200.sf.net/firmware.php
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch allows the user to set the handover threshold, i.e. the number
of consecutively missed beacons that will trigger a roaming attempt. The
disassociation threshold is set to 3 times the handover threshold.
Signed-off-by: Olivier Hochreutiner <olivier.hochreutiner@epfl.ch>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This forces one antenna or the other, if the background noise is
significantly quieter in one than the other. It favors the quieter
antenna, and won't kick in unless the difference is significant.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set a meaningful silence threshold value (replacing our previous "0"
default), which gets rid of the gratuitous "Link deterioration"
notifications that we've been receiving from firmware. This
notification feature tells the driver information to help it determine
when to pre-emptively restart the firmware/ucode in anticipation of
firmware errors! But since setting this new threshold, I haven't seen
any such notifications. At least it keeps the logs a little less busy.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently iwlist ethX freq[uency]/channel lists all the channels the card
supported for the current region, which includes some channels can only
be used in infrastructure mode. This patch filters these channels out if
the card is currently in ad-hoc mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When loading the ipw2200 module with disabled=1, rf_kill is activated after
every mode change. This is caused by ipw_sw_reset() is called when a mode
is changed. The patch fixed the problem by distinguishing the purposes with
the 'option' paramenter.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wpa_supplicant needs to set wpa_enabled unconditionally, with this check
it hasn't been possible to connect to non-WPA networks using wpa_supplicant.
So remove below check.
if (priv->ieee->wpa_enabled &&
network->wpa_ie_len == 0 && network->rsn_ie_len == 0)
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
