This patch adds GSO support for IPv6 and TCPv6. This is based on a patch
by Ananda Raju <Ananda.Raju@neterion.com>. His original description is:
This patch enables TSO over IPv6. Currently Linux network stacks
restricts TSO over IPv6 by clearing of the NETIF_F_TSO bit from
"dev->features". This patch will remove this restriction.
This patch will introduce a new flag NETIF_F_TSO6 which will be used
to check whether device supports TSO over IPv6. If device support TSO
over IPv6 then we don't clear of NETIF_F_TSO and which will make the
TCP layer to create TSO packets. Any device supporting TSO over IPv6
will set NETIF_F_TSO6 flag in "dev->features" along with NETIF_F_TSO.
In case when user disables TSO using ethtool, NETIF_F_TSO will get
cleared from "dev->features". So even if we have NETIF_F_TSO6 we don't
get TSO packets created by TCP layer.
SKB_GSO_TCPV4 renamed to SKB_GSO_TCP to make it generic GSO packet.
SKB_GSO_UDPV4 renamed to SKB_GSO_UDP as UFO is not a IPv4 feature.
UFO is supported over IPv6 also
The following table shows there is significant improvement in
throughput with normal frames and CPU usage for both normal and jumbo.
--------------------------------------------------
| | 1500 | 9600 |
| ------------------|-------------------|
| | thru CPU | thru CPU |
--------------------------------------------------
| TSO OFF | 2.00 5.5% id | 5.66 20.0% id |
--------------------------------------------------
| TSO ON | 2.63 78.0 id | 5.67 39.0% id |
--------------------------------------------------
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GSO to workaround a rare TSO bug on some chips. This hardware
bug may be triggered when the TSO header size is greater than 80
bytes. When this condition is detected in a TSO packet, the driver
will use GSO to segment the packet to workaround the hardware bug.
Thanks to Juergen Kreileder <jk@blackdown.de> for reporting the
problem and collecting traces to help debug the problem.
And thanks to Herbert Xu <herbert@gondor.apana.org.au> for providing
the GSO mechanism that happens to be the perfect workaround for this
problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear a bit to enable a hardware fix for some ASF related problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround to limit the burst size of rx BDs being DMA'ed to the
chip. This works around hardware errata on a number of 5750, 5752,
and 5755 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tg3_netif_stop() when changing the vlgrp (vlan group) pointer. It
is necessary to quiesce the device before changing that pointer.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set alternate port number when initializing QP attributes. This bug
is OpenFabrics bugzilla bug #160.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Store away the user handle passed in from userspace when creating an
SRQ, so that the kernel can return the correct handle when an SRQ
asynchronous event occurs. (A 0 was incorrectly stored as the user
handle as part of the changes in 9ead190b, "IB/uverbs: Don't serialize
with ib_uverbs_idr_mutex")
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PCMCIA layer calls pcmcia_parse_events both from user context and
IRQ context; the lock thus needs to be irqsave to avoid deadlocks
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Enable the com20020_cs arcnet driver to see the SoHard (now Mercury
Computer Systems Inc.) SH ARC-PCMCIA card.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This must not be marked __init, as it is called from
au1x00_drv_pcmcia_probe.
Signed-off-by: Domen Puncer <domen.puncer@ultra.si>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
... to make sure that it doesn't break again when a field changes (see
"[PATCH] pcmcia: fix zeroing of cm4000_cs.c data" for recent example).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert pcmcia_cs to use kthread instead of the deprecated
kernel_thread.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Comment out the ID 0xc00f,0x0000 in hostap_cs.c, as it conflicts with the
pcnet_cs driver.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
AT91 CF updates, mostly for power management:
- Add suspend/resume methods to the AT91 CF driver, disabling
non-wakeup IRQs during system suspend. The card detect IRQ
serves as a wakeup event source.
- Convert the driver to the more-current "platform_driver" style.
So inserting or removing a CF card will wake the system, unless that
has been disabled by updating the sysfs file; and there will be no
more warnings about spurious IRQs during suspend/resume cycles.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch enables ide_cs to access CF-cards via their common memory
rather than via their IO space.
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The patch below adds support for the TI PCIxx12 CardBus controllers.
This seems to be sufficient to detect the cardbus bridge on an HP nc6320
and works with an orinoco wifi card.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The patch below cleans up the pcmcia code a bit on the IRQ side (I did
this while debugging the problem just so I could read wtf it was doing),
and also adds a warning and passes back the correct information when a
device asks for exclusive but gets given shared. This at least means the
dmesg dump of a problem triggered by this will have a signature to find.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fixup the subordinate number parent bridge of yenta Cardbus Bridges
before the PCI bus scan starts to make the cardbus cards which are
otherwise hidden for PCI scans work.
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Power-up the card only after the socket is configured. power-down in
the old place. The point is not to power-up the card before the interrupt
routing is set up correctly.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Stumbled over this because of coverity (id #492),
seems like we are missing a return statement here and fail
to do proper bounds checking. If this assumption is false
we should at least change the identation to make it clear
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 unused global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the Geniatech Digistar, aka
Digiwave 103g DVB-S card.
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Saqeb Akhter <johoja@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The set_voltage function in cx24123.c was corrected to match how it is
described in the CX24123 specs, producing the correct behaviour for cards
that require it.
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Saqeb Akhter <johoja@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The original driver had a restriction that if a card as an saa7113 chip,
then it cannot have a CI interface. This is not the case.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These cards do not need the tda10021 configuration change when data is
streamed through a CAM module. This disables it for these ones.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When someone added the front-end ioctl FE_SET_FRONTEND_TUNE_MODE, they
forgot to set the return value to 0. It always returns EOPNOTSUPP,
causing problems for programmers who actually check for error conditions.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously the pvrusb2 driver was conditionalizing printing of the
device register / unregister messages against a debug mask. This sort
of information should always appear, thus this patch.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The supported standards by the tuner on tveeprom were too restricted.
It were showing just the main format, instead of the format family.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Many tda9887 settings depend on the chosen tuner. Expand the tuner parameters
to include these tda9887 settings.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should no longer try to load the tda9887 module, because it no longer
exists. The tda9887 driver has been merged into the tuner module.
This patch removes all instances of request_module("tda9887") from
the following video4linux drivers: bttv, cx88, em28xx and saa7134.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch implements the newer v4l2 control features to make the
standard user controls and mpeg encoder controls of cx88-blackbird
video encoder boards available to userspace.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/i2c/busses/i2c-i801.c: In function 'i801_probe':
drivers/i2c/busses/i2c-i801.c:496: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'resource_size_t'
Cc: Greg KH <greg@kroah.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add lower-level functions that handle various parts of the initialization
done by the xxx_probe1() functions. Some of the xxx_probe1() functions are
much too long and complicated (see "Chapter 5: Functions" in
Documentation/CodingStyle).
- Cleanup of probe1() functions in EDAC
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove add_mc_to_global_list(). In next patch, this function will be
reimplemented with different semantics.
1 Reimplement add_mc_to_global_list() with semantics that allow the caller to
determine the ID number for a mem_ctl_info structure. Then modify
edac_mc_add_mc() so that the caller specifies the ID number for the new
mem_ctl_info structure. Platform-specific code should be able to assign the
ID numbers in a platform-specific manner. For instance, on Opteron it makes
sense to have the ID of the mem_ctl_info structure match the ID of the node
that the memory controller belongs to.
2 Modify callers of edac_mc_add_mc() so they use the new semantics.
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change MC drivers from using CVS revision strings for their version number,
Now each driver has its own local string.
Remove some PCI dependencies from the core EDAC module. Made the code 'struct
device' centric instead of 'struct pci_dev' Most of the code changes here are
from a patch by Dave Jiang. It may be best to eventually move the
PCI-specific code into a separate source file.
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- make __cm206_init() __init (required since it calls
the __init cm206_init())
- make the needlessly global bcdbin() static
- remove a comment with an obsolete compile command
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't show a menu that can't be entered due to lack of contents on arm (the
options are only available on arm26).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Ian Molton <spyro@f2s.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the USB core to save and pass the sending task secid when
sending signals upon AIO completion so that proper security checking can be
applied by security modules.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remaining counters in page_state after the zoned VM counter patches
have been applied are all just for show in /proc/vmstat. They have no
essential function for the VM.
We use a simple increment of per cpu variables. In order to avoid the most
severe races we disable preempt. Preempt does not prevent the race between
an increment and an interrupt handler incrementing the same statistics
counter. However, that race is exceedingly rare, we may only loose one
increment or so and there is no requirement (at least not in kernel) that
the vm event counters have to be accurate.
In the non preempt case this results in a simple increment for each
counter. For many architectures this will be reduced by the compiler to a
single instruction. This single instruction is atomic for i386 and x86_64.
And therefore even the rare race condition in an interrupt is avoided for
both architectures in most cases.
The patchset also adds an off switch for embedded systems that allows a
building of linux kernels without these counters.
The implementation of these counters is through inline code that hopefully
results in only a single instruction increment instruction being emitted
(i386, x86_64) or in the increment being hidden though instruction
concurrency (EPIC architectures such as ia64 can get that done).
Benefits:
- VM event counter operations usually reduce to a single inline instruction
on i386 and x86_64.
- No interrupt disable, only preempt disable for the preempt case.
Preempt disable can also be avoided by moving the counter into a spinlock.
- Handling is similar to zoned VM counters.
- Simple and easily extendable.
- Can be omitted to reduce memory use for embedded use.
References:
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=113512330605497&w=2
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=114988082814934&w=2
local_t http://marc.theaimsgroup.com/?l=linux-kernel&m=114991748606690&w=2
V2 http://marc.theaimsgroup.com/?t=115014808400007&r=1&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767022346&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115047968808926&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The numa statistics are really event counters. But they are per node and
so we have had special treatment for these counters through additional
fields on the pcp structure. We can now use the per zone nature of the
zoned VM counters to realize these.
This will shrink the size of the pcp structure on NUMA systems. We will
have some room to add additional per zone counters that will all still fit
in the same cacheline.
Bits Prior pcp size Size after patch We can add
------------------------------------------------------------------
64 128 bytes (16 words) 80 bytes (10 words) 48
32 76 bytes (19 words) 56 bytes (14 words) 8 (64 byte cacheline)
72 (128 byte)
Remove the special statistics for numa and replace them with zoned vm
counters. This has the side effect that global sums of these events now
show up in /proc/vmstat.
Also take the opportunity to move the zone_statistics() function from
page_alloc.c into vmstat.c.
Discussions:
V2 http://marc.theaimsgroup.com/?t=115048227000002&r=1&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_bounce to a per zone counter
nr_bounce is only used for proc output. So it could be left as an event
counter. However, the event counters may not be accurate and nr_bounce is
categorizing types of pages in a zone. So we really need this to also be a
per zone counter.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_unstable to a per zone counter
We need to do some special modifications to the nfs code since there are
multiple cases of disposition and we need to have a page ref for proper
accounting.
This converts the last critical page state of the VM and therefore we need to
remove several functions that were depending on GET_PAGE_STATE_LAST in order
to make the kernel compile again. We are only left with event type counters
in page state.
[akpm@osdl.org: bugfixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_writeback to per zone counter.
This removes the last page_state counter from arch/i386/mm/pgtable.c so we
drop the page_state from there.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes nr_dirty a per zone counter. Looping over all processors is
avoided during writeback state determination.
The counter aggregation for nr_dirty had to be undone in the NFS layer since
we summed up the page counts from multiple zones. Someone more familiar with
NFS should probably review what I have done.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_page_table_pages to a per zone counter
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Allows reclaim to access counter without looping over processor counts.
- Allows accurate statistics on how many pages are used in a zone by
the slab. This may become useful to balance slab allocations over
various zones.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current NR_FILE_MAPPED is used by zone reclaim and the dirty load
calculation as the number of mapped pagecache pages. However, that is not
true. NR_FILE_MAPPED includes the mapped anonymous pages. This patch
separates those and therefore allows an accurate tracking of the anonymous
pages per zone.
It then becomes possible to determine the number of unmapped pages per zone
and we can avoid scanning for unmapped pages if there are none.
Also it may now be possible to determine the mapped/unmapped ratio in
get_dirty_limit. Isnt the number of anonymous pages irrelevant in that
calculation?
Note that this will change the meaning of the number of mapped pages reported
in /proc/vmstat /proc/meminfo and in the per node statistics. This may affect
user space tools that monitor these counters! NR_FILE_MAPPED works like
NR_FILE_DIRTY. It is only valid for pagecache pages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently a single atomic variable is used to establish the size of the page
cache in the whole machine. The zoned VM counters have the same method of
implementation as the nr_pagecache code but also allow the determination of
the pagecache size per zone.
Remove the special implementation for nr_pagecache and make it a zoned counter
named NR_FILE_PAGES.
Updates of the page cache counters are always performed with interrupts off.
We can therefore use the __ variant here.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nr_mapped is important because it allows a determination of how many pages of
a zone are not mapped, which would allow a more efficient means of determining
when we need to reclaim memory in a zone.
We take the nr_mapped field out of the page state structure and define a new
per zone counter named NR_FILE_MAPPED (the anonymous pages will be split off
from NR_MAPPED in the next patch).
We replace the use of nr_mapped in various kernel locations. This avoids the
looping over all processors in try_to_free_pages(), writeback, reclaim (swap +
zone reclaim).
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/char/istallion.c: In function âstli_initbrdsâ:
drivers/char/istallion.c:4150: error: implicit declaration of function âstli_parsebrdâ
drivers/char/istallion.c:4150: error: âstli_brdspâ undeclared (first use in this function)
drivers/char/istallion.c:4150: error: (Each undeclared identifier is reported only once
drivers/char/istallion.c:4150: error: for each function it appears in.)
drivers/char/istallion.c:4164: error: implicit declaration of function âstli_argbrdsâ
While I was at it, I also removed the #ifdef MODULE around the initialation
code to allow it to perhaps work when built into the kernel and made a
needlessly global function static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes drivers/char/pc8736x_gpio.c and drivers/char/scx200_gpio.c to
use the platform_device_del/put ops correctly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix build error on x86_64. There's nothing even remotely close to
imacmp_seg in the kernel, so I removed the whole line.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Edgar Hucek <hostmaster@ed-soft.at>
Cc: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo spotted by
Matt LaPlante <webmaster@cyberdogtech.com>.
This patch fixes kernel Bugzilla #6704.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
- Use it instead of acpi_bus_get_device() in acpi_video_bus_notify()
and use the one from struct acpi_video_device in
acpi_video_device_notify().
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- Use it instead of acpi_bus_get_device() where we can..
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- Use it instead of acpi_bus_get_device() where we can..
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Misc cleanups in ondemand. Should have zero functional impact.
Also adding Alexey as author.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Make ondemand sampling per CPU and remove the mutex usage in sampling path.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove slowdown from ondemand sampling path. This reduces the code path length
in dbs_check_cpu() by half. slowdown was not used by ondemand by default.
If there are any user level tools that were using this tunable, they
may report error now.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
[TIPC]: Initial activation message now includes TIPC version number
[TIPC]: Improve response to requests for node/link information
[TIPC]: Fixed skb_under_panic caused by tipc_link_bundle_buf
[IrDA]: Fix the AU1000 FIR dependencies
[IrDA]: Fix RCU lock pairing on error path
[XFRM]: unexport xfrm_state_mtu
[NET]: make skb_release_data() static
[NETFILTE] ipv4: Fix typo (Bugzilla #6753)
[IrDA]: MCS7780 usb_driver struct should be static
[BNX2]: Turn off link during shutdown
[BNX2]: Use dev_kfree_skb() instead of the _irq version
[ATM]: basic sysfs support for ATM devices
[ATM]: [suni] change suni_init to __devinit
[ATM]: [iphase] should be __devinit not __init
[ATM]: [idt77105] should be __devinit not __init
[BNX2]: Add NETIF_F_TSO_ECN
[NET]: Add ECN support for TSO
[AF_UNIX]: Datagram getpeersec
[NET]: Fix logical error in skb_gso_ok
[PKT_SCHED]: PSCHED_TADD() and PSCHED_TADD2() can result,tv_usec >= 1000000
...
AU1000 FIR is broken, it should depend on SOC_AU1000.
Spotted by Jean-Luc Leger.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes a needlessly global struct static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor change in shutdown logic to effect a link down.
Update version to 1.4.43.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all dev_kfree_skb_irq() and dev_kfree_skb_any() to
dev_kfree_skb(). These calls are never used in irq context.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NETIF_F_TSO_ECN feature for all bnx2 hardware.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Need to unregister 2 ports per of_device.
2) Need to of_iounmap() 1 mapping per of_device.
3) Need to free up the IRQ only after all devices
have been unregistered.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes pxa2xx_udc.c to include asm/arch/udc.h again to fix current
build breakage.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
[ forwarded by David Brownell <david-b@pacbell.net> ]
[ fixed to apply properly by Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
If all drivers go away before all ISDN network interfaces are closed we got
a OOps on removing interfaces, this patch avoid it.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
most current laptops do not work without allowing shared cardbus IRQs.
This patch enables IRQ sharing, so these cards work again.
This was tested with shared and none shared cardbus IRQs on different laptops
without problems.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (43 commits)
[POWERPC] Use little-endian bit from firmware ibm,pa-features property
[POWERPC] Make sure smp_processor_id works very early in boot
[POWERPC] U4 DART improvements
[POWERPC] todc: add support for Time-Of-Day-Clock
[POWERPC] Make lparcfg.c work when both iseries and pseries are selected
[POWERPC] Fix idr locking in init_new_context
[POWERPC] mpc7448hpc2 (taiga) board config file
[POWERPC] Add tsi108 pci and platform device data register function
[POWERPC] Add general support for mpc7448hpc2 (Taiga) platform
[POWERPC] Correct the MAX_CONTEXT definition
powerpc: minor cleanups for mpc86xx
[POWERPC] Make sure we select CONFIG_NEW_LEDS if ADB_PMU_LED is set
[POWERPC] Simplify the code defining the 64-bit CPU features
[POWERPC] powerpc: kconfig warning fix
[POWERPC] Consolidate some of kernel/misc*.S
[POWERPC] Remove unused function call_with_mmu_off
[POWERPC] update asm-powerpc/time.h
[POWERPC] Clean up it_lp_queue.h
[POWERPC] Skip the "copy down" of the kernel if it is already at zero.
[POWERPC] Add the use of the firmware soft-reset-nmi to kdump.
...
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (23 commits)
[PARISC] Move os_id_to_string() inside #ifndef __ASSEMBLY__
[PARISC] Fix do_gettimeofday() hang
[PARISC] Fix PCREL22F relocation problem for most modules
[PARISC] Refactor show_regs in traps.c
[PARISC] Add os_id_to_string helper
[PARISC] OS_ID_LINUX == 0x0006
[PARISC] Ensure Space ID hashing is turned off
[PARISC] Match show_cache_info with reality
[PARISC] Remove unused macro fixup_branch in syscall.S
[PARISC] Add is_compat_task() helper
[PARISC] Update Thibaut Varene's CREDITS entry
[PARISC] Reduce data footprint in pdc_stable.c
[PARISC] pdc_stable version 0.30
[PARISC] Work around machines which do not support chassis warnings
[PARISC] PDC_CHASSIS is implemented on all machines
[PARISC] Remove unconditional #define PIC in syscall macros
[PARISC] Use MFIA in current_text_addr on pa2.0 processors
[PARISC] Remove dead function pc_in_user_space
[PARISC] Test ioc_needs_fdc variable instead of open coding
[PARISC] Fix gcc 4.1 warnings in sba_iommu.c
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Coverity spotted this leak (id #613), when we are not configured, we return
without freeing the allocated skb.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AFAICT, this is x86 only, so the patch below is needed to stop this new
option showing up on PPC, IA64, etc..
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another possible dereference detected by coverity (id #759). pf_probe()
might call pf_identify() which might call get_capacity() which dereferences
pf->disk
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Documention/pci.txt states..
"The struct pci_driver shouldn't be marked with any of these tags."
(Referring to __devinit and friends).
(akpm: good documentation, that. Link this driver into vmlinux with hotplug
CPU disabled and it'll crash).
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/built-in.o: In function `sgivwfb_set_par':
sgivwfb.c:(.text+0x88583): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.text+0x88596): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.text+0x885a8): undefined reference to `sgivwfb_mem_phys'
drivers/built-in.o: In function `sgivwfb_check_var':
sgivwfb.c:(.text+0x88ad0): undefined reference to `sgivwfb_mem_size'
drivers/built-in.o: In function `sgivwfb_mmap':
sgivwfb.c:(.text+0x88c75): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.text+0x88c7f): undefined reference to `sgivwfb_mem_phys'
drivers/built-in.o: In function `sgivwfb_probe':
sgivwfb.c:(.init.text+0x4060): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.init.text+0x4065): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.init.text+0x4076): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.init.text+0x409c): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.init.text+0x410e): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.init.text+0x4113): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.init.text+0x4162): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.init.text+0x4168): undefined reference to `sgivwfb_mem_phys'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bit of a brown paper bag issue. The previous patch to remove the soon
to be ripped out fields that were used in autosense actually broke the
driver. This patch fixes it and has been tested (honestly).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds or modifies the transport class functions
used to notify userspace of session state events.
We modify the session addition up event and add a destruction event
to notify userspace of session creation, relogin and destruction.
And we modify the conn error event to be sent by broadcast
since multiple listeners may want to listen for it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
So the drivers do not use the channel numbers, but some do
use the target numbers. We were just adding some goofy
variable that just increases for the target nr. This is useless
for software iscsi because it is always zero. And for qla4xxx
the target nr is actually the index of the target/session
in its FW or FLASH tables. We needed to expose this to userspace
so apps could access those numbers so this patch just adds the
target nr to the iscsi session creation functions. This way
when qla4xxx's Hw thinks a session is at target nr 4
in its hw, it is exposed as that number in sysfs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
qla4xxx is initialized in two steps like other HW drivers.
It allocates the host, sets up the HW, then adds the host.
For iscsi part of HW setup is setting up persistent iscsi
sessions. At that time, the interupts are off and the driver
is not completely set up so we just want to allocate them.
We do not want to add them to sysfs and expose them to userspace
because userspace could try to do lots of fun things with them
like scanning and at that time the driver is not ready.
So this patch breakes up the session creation like other
functions that use the driver model in two the alloc
and add parts. When the driver is ready, it can then add
the sessions and userspace can begin using them.
This also fixes a bug in the addition error patch where
we forgot to do a get on the session.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I do not remember what I was thinking when we added the channel
as a argument to the session create function. It was probably
due to too much cut and paste work from the FC transport class.
The channel is meaningless for iscsi drivers so this patch drops
its usage everywhere in the iscsi related code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iscsi_tcp and iser cannot be rmmod from the kernel when sessions
are running because session removal is driven from userspace. For
those modules we get a module reference when a session is
created then drop it when the session is removed.
For qla4xxx, they can jsut remove the sessions from the pci remove
function like normal HW drivers, so this patch moves the module
reference from the transport class functions shared by all
drivers to the libiscsi functions only used be software iscsi
modules.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert iscsi_tcp to new lib functions.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert iser to libiscsi get/set param functions.
Fix bugs in it returning old error return values and
have it expose exp_statsn.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Reduce duplication in the software iscsi_transport modules by
adding a libiscsi function to handle the common grunt work.
This also has the drivers return specifc -EXXX values for different
errors so userspace can finally handle them in a sane way.
Also just pass the sysfs buffers to the drivers so HW iscsi can
get/set its string values, like targetname, and initiatorname.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from david.somayajulu@qlogic.com:
Add target discovery event. We may have a setup where the iscsi traffic
is on a different netowrk than the other network traffic. In this case
we will want to do discovery though the iscsi card. This patch adds
a event to the transport class that can be used by hw iscsi cards that
support this.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I noticed that in_use in st_buffer is not used. The patch below
against 2.6.17-rc3 removes it, assuming there is no future use for it.
It was tested in a sparc SS20 with a DLT4000.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Acked-by: Kai Mkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes for several channel measurement facility bugs:
* Blocks copied from the hardware might not be consistent. Solve this
by moving the copying into idle state and repeating the copying.
* avg_sample_interval changed with every read, even though no new block
was available. Solve this by storing a timestamp when the last new
block was received.
* Several locking issues.
* Measurements were not reenabled after a disconnected device became
available again.
* Remove #defines for ioctls that were never implemented.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for parallel-access-volumes to the dasd driver. This
allows concurrent access to dasd devices with multiple channel
programs.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After setting a path to a dasd offline at the SE, I/O hangs on that
dasd for 5 minutes, then continues.
I/O for which an interrupt will not be reported after the channel
path has been disabled was not terminated by the common I/O layer,
causing the dasd MIH to hit after 5 minutes.
Be more aggressive in terminating I/O after setting a channel path
offline. Also make sure to generate a fake irb if the device
driver issues an I/O request after being notified of the killed
I/O and clear residual information from the irb before trying to
start the delayed verification.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
as a deprecated kernel_thread to a kthread.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The struct dasd_eer_header needs the packed attribute, or there will
be 6 additional bytes of random data between the fixed header and
the variable length part of the eer data.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Dasd code cleanup: 1) remove white space, 2) remove the emacs override
sections, and 3) use kzalloc instead of kmalloc.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ccw dump function dasd_eckd_dump_ccw_range can crash because
it does not take care about the IDAL flag in the ccw.
Check for IDALs flag set in CCW and follow the indirect list to
print the data that is refered by the ccw.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Check the return value of kzalloc in dasd_eer_open.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The initial i/o to a 3270 device is done using the static module variables
raw3270_init_data and raw3270_init_request. If the 3270 device driver is
built as a module and gets loaded above 2GB, the initial i/o will fail
because these variables will get addresses > 2GB. To make it work the
two variables are moved to struct raw3270 and the data structure is
allocated with GFP_DMA.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Changes in the DASD driver require an asynchronous implementation of the
subchannel reprobe loop. This loop was so far only used by the blacklisting
mechanism but is now available to all CCW device drivers.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Work around the problem that a device cannot be unregistered from
driver_for_each_device() because of klist node refcounting: Get device
after device owned by the driver to be unregistered with driver_find_device()
and then unregister it. This works because driver_get_device() gets us out of
the region of the elevated klist node refcount. driver_find_device() will
always get the next device in the list after the found one has been
unregistered.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Specify correct sizeof() in chp_measurement_read() and return
correct amount of read data.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Trying to set a DASD root device online can fail under some circumstances
with the message "Read configuration data returned error -5". The cause
is that read configuration data incorrectly aborts with -EIO when it
encounters a temporary busy condition at a storage server.
Perform retry when encountering temporary busy conditions.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix all kernel-doc warnings in MTD headers and source files:
- add some missing struct fields;
- correct some function parameter names;
- use kernel-doc format for function doc. headers;
- nand_ecc.c contains only exported interfaces, no internal ones;
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds earlier initialization of spi_device.mode, as needed
on boards using nondefault chipselect polarity. An example would be
ones using the RS5C348 RTC without an external signal inverter between
the RTC chipselect and the SPI controller.
Without this mechanism, the first setup() call for that chip would
wrongly enable chips, corrupting transfers to/from other chips sharing
that SPI bus.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also sets the new fifo flag so that we don't hang on some errors with this
chipset.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move auto arrays to static (const). Clean up using PCI_DEVICE in places,
remove unreachable junk and dead code.
Fix the serverworks cable detect logic (if ordering is wrong). Backport
from libata. Plenty of scope for more cleanup left.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the controller FIFO cleared automatically on error we must not try
and drain it as this will hang some chips.
Based in concept on a broken patch from -mm some while back
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kill a pair of long escaped debug printk calls
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove all the ifdef preparation for enhanced features that never occcurred
and is only in libata. For the SATA chips (but not yet PATA ones) politely
suggest to the user that libata may offer more features.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylylov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is based on the proposed patches flying around but also checks that
the device in question is new enough to have word 93 rather thanb blindly
assuming word 93 == 0 means SATA (see ATA-5, ATA-7)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a erroneous calculation of the legacy brightness values as reported by
Paul Collins. Additionally, it moves the calculation of the negative value
in the radeonfb driver after the value check.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Collins <paul@briny.ondioline.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the watchdog timeout in IPMI to only do things at panic/reboot time if
the watchdog timer was already running. Some BIOSes do not disable the
watchdog timer at startup, and this led to a reboot a while later if the new
OS running didn't start monitoring the watchdog, even if the watchdog was not
running before.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was some old high-res-timer code in the IPMI driver that is dead.
Remove it.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tidy up the timer usage in the IPMI driver.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Turned out to be rather a monster
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Works better on SMP if...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove 'active' field from tty buffer structure. This was added in 2.6.16
as part of a patch to make the new tty buffering SMP safe. This field is
unnecessary with the more intelligently written flush_to_ldisc that adds
receive_room handling.
Removing this field reverts to simpler logic where the tail buffer is
always the 'active' buffer, which should not be freed by flush_to_ldisc.
(active == buffer being filled with new data)
The result is simpler, smaller, and faster tty buffer code.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Flush data serially to line discipline in blocks no larger than
tty->receive_room to avoid losing data if line discipline is busy (such as
N_TTY operating at high speed on heavily loaded system) or does not accept
data in large blocks (such as N_MOUSE).
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove TTY_DONT_FLIP tty flag. This flag was introduced in 2.1.X kernels
to prevent the N_TTY line discipline functions read_chan() and
n_tty_receive_buf() from running at the same time. 2.2.15 introduced
tty->read_lock to protect access to the N_TTY read buffer, which is the
only state requiring protection between these two functions.
The current TTY_DONT_FLIP implementation is broken for SMP, and is not
universally honored by drivers that send data directly to the line
discipline receive_buf function.
Because TTY_DONT_FLIP is not necessary, is broken in implementation, and is
not universally honored, it is removed.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Same as with already do with the file operations: keep them in .rodata and
prevents people from doing runtime patching.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/scsi/aacraid/comminit.c
Fixed up by removing the now renamed CONFIG_IOMMU option from
aacraid
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The atp870u driver is the largest stack eater reported by checkstack
(on x86_864, allmodconfig). This converts the offending function
to kmalloc+kfree struct atp_unit instead of allocating it on the stack.
Was:
0x0000164c atp870u_probe [atp870u]: 3176
Now:
0x0000164c atp870u_probe [atp870u]: 408
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Adding 1078 ROC (Raid On Chip) Support - New host adapter
* Moving all PCI Vendor/Device ids to using internal defines; a request
from Christoph/James B. some time ago for when the next chip was added.
* Removing SAS 1066/1066E Vendor/Device IDs, as there are no plans to
manufacture that controller.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Wide port support added - using James Bottomley's new SAS wide port API.
(There is a known problem in sas transport layer reported yesterday to
James. The Kobject dev.bus_ids for end devices are not unique across
expanders. I have added a work around in this patch, where I asigning
an unique port identifier for every port within the host - this solves
the problem, but I expect a fix from James in the sas transport).
* Adding target_alloc and target_destroy entry points, and moving code over
from the slave entry points.
* The renaming of some mptscsih_xxx functions declared in mptsas.c,
to mptsas_xxx.
* Target Reset moved from slave_destroy to hotplug work thread
handling (with regard to device removal). Also inhibit IO to end device
while device is being broken down . Talked to James Smart about this
at Linux Expo (with questions of how the fc transport handles this).
* Cleaning up the kzalloc's, and kfree's
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
this patch introduces a port object, separates out ports and phys,
with ports becoming the primary objects of the tree.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a device gets offlined as a result of the Inquiry sent
during scanning, the following oops can occur. After the
disk gets put into the SDEV_OFFLINE state, the error handler
sends back the failed inquiry, which wakes the thread doing
the scan. This starts a race between the scanning thread
freeing the scsi device and the error handler calling
scsi_run_host_queues to restart the host. Since the disk
is in the SDEV_OFFLINE state, scsi_device_get will still
work, which results in __scsi_iterate_devices getting
a reference to the scsi disk when it shouldn't.
The following execution thread causes the oops:
CPU 0 (scan) CPU 1 (eh)
---------------------------------------------------------
scsi_probe_and_add_lun
....
scsi_eh_offline_sdevs
scsi_eh_flush_done_q
scsi_destroy_sdev
scsi_device_dev_release
scsi_restart_operations
scsi_run_host_queues
__scsi_iterate_devices
get_device
scsi_device_dev_release_usercontext
scsi_run_queue
<---OOPS--->
The patch fixes this by changing the state of the sdev to SDEV_DEL
before doing the final put_device, which should prevent the race
from occurring.
Original oops follows:
Badness in kref_get at lib/kref.c:32
Call Trace:
[C00000002F4476D0] [C00000000000EE20] .show_stack+0x68/0x1b0 (unreliable)
[C00000002F447770] [C00000000037515C] .program_check_exception+0x1cc/0x5a8
[C00000002F447840] [C00000000000446C] program_check_common+0xec/0x100
Exception: 700 at .kref_get+0x10/0x28
LR = .kobject_get+0x20/0x3c
[C00000002F447B30] [C00000002F447BC0] 0xc00000002f447bc0 (unreliable)
[C00000002F447BB0] [C000000000254BDC] .get_device+0x20/0x3c
[C00000002F447C30] [D000000000063188] .scsi_device_get+0x34/0xdc [scsi_mod]
[C00000002F447CC0] [D0000000000633EC] .__scsi_iterate_devices+0x50/0xbc [scsi_mod]
[C00000002F447D60] [D00000000006A910] .scsi_run_host_queues+0x34/0x5c [scsi_mod]
[C00000002F447DF0] [D000000000069054] .scsi_error_handler+0xdb4/0xe44 [scsi_mod]
[C00000002F447EE0] [C00000000007B4E0] .kthread+0x128/0x178
[C00000002F447F90] [C000000000025E84] .kernel_thread+0x4c/0x68
Unable to handle kernel paging request for <7>PCI: Enabling device: (0002:41:01.1), cmd 143
data at address 0x000001b8
Faulting instruction address: 0xd0000000000698e4
sym1: <1010-66> rev 0x1 at pci 0002:41:01.1 irq 216
sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi2 : sym-2.2.2
cpu 0x0: Vector: 300 (Data Access) at [c00000002f447a30]
pc: d0000000000698e4: .scsi_run_queue+0x2c/0x218 [scsi_mod]
lr: d00000000006a904: .scsi_run_host_queues+0x28/0x5c [scsi_mod]
sp: c00000002f447cb0
msr: 9000000000009032
dar: 1b8
dsisr: 40000000
current = 0xc0000000045fecd0
paca = 0xc00000000048ee80
pid = 1123, comm = scsi_eh_1
enter ? for help
[c00000002f447d60] d00000000006a904 .scsi_run_host_queues+0x28/0x5c [scsi_mod]
[c00000002f447df0] d000000000069054 .scsi_error_handler+0xdb4/0xe44 [scsi_mod]
[c00000002f447ee0] c00000000007b4e0 .kthread+0x128/0x178
[c00000002f447f90] c000000000025e84 .kernel_thread+0x4c/0x68
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a resend of a patch I generated in response to an email sent
by Ruben Faelens <parasietje@gmail.com>. His original email to
linux-scsi requested a method in which he could spin down a scsi disk
when not in use and have the kernel automatically spin it back up when
an I/O was generated to the disk. The infrastructure to automatically
spin a disk up has been in the scsi error handler for some time now,
but it is not enabled by default. This patch adds an sd sysfs attribute
which allows userspace to enable this behavior.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The NAND rework resulted in non ECC based reads. Fix it up and
do a bit of cleanup while at it.
Pointed out by Adrian Bunk.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While trying to look for superfluous I/O accesses that can be optimized
away, I stumbled upon this ACPI sleep I/O access and couldn't figure out
why the hell this dummy op was necessary.
After more than one hour of internet research, I had collected a sufficient
number of documents (among those very old kernel versions) that finally
told me what this dummy read was about: STPCLK# doesn't get asserted in time
on (some) chipsets, which is why we need to have a dummy I/O read to delay
further instruction processing until the CPU is fully stopped.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Only if bus master activity is going on at the present, we should avoid
entering C3-type sleep, as it might be a faulty transition. As long as the
bm_activity bitmask was based on the number of calls to the ACPI idle
function, looking at previous moments made sense. Now, with it being based on
what happened this jiffy, looking at this jiffy should be sufficient.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Do not assume there was bus mastering activity if the idle handler didn't get
called, as there's only reason to not enter C3-type sleep if there is bus
master activity going on. Only for the "promotion" into C3-type sleep bus
mastering activity is taken into account, and there only current bus mastering
activity, and not pure guessing should lead to the decision on whether to
enter C3-type sleep or not.
Also, as bm_activity is a jiffy-based bitmask (bit 0: bus mastering activity
during this juffy, bit 31: bus mastering activity 31 jiffies ago), fix the
setting of bit 0, as it might be called multiple times within one jiffy.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Track the actual time spent in C-States (C2 upwards, we can't determine this
for C1), not only the number of invocations. This is especially useful for
dynamic ticks / "tickless systems", but is also of interest on normal systems,
as any interrupt activity leads to C-States being exited, not only the timer
interrupt.
The time is being measured in PM timer ticks, so an increase by one equals 279
nanoseconds.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented a new acpi_spinlock type for the OSL lock
interfaces. This allows the type to be customized to
the host OS for improved efficiency (since a spinlock is
usually a very small object.)
Implemented support for "ignored" bits in the ACPI
registers. According to the ACPI specification, these
bits should be preserved when writing the registers via
a read/modify/write cycle. There are 3 bits preserved
in this manner: PM1_CONTROL[0] (SCI_EN), PM1_CONTROL[9],
and PM1_STATUS[11].
http://bugzilla.kernel.org/show_bug.cgi?id=3691
Implemented the initial deployment of new OSL mutex
interfaces. Since some host operating systems have
separate mutex and semaphore objects, this feature was
requested. The base code now uses mutexes (and the new
mutex interfaces) wherever a binary semaphore was used
previously. However, for the current release, the mutex
interfaces are defined as macros to map them to the
existing semaphore interfaces.
Fixed several problems with the support for the control
method SyncLevel parameter. The SyncLevel now works
according to the ACPI specification and in concert with the
Mutex SyncLevel parameter, since the current SyncLevel is
a property of the executing thread. Mutual exclusion for
control methods is now implemented with a mutex instead
of a semaphore.
Fixed three instances of the use of the C shift operator
in the bitfield support code (exfldio.c) to avoid the use
of a shift value larger than the target data width. The
behavior of C compilers is undefined in this case and can
cause unpredictable results, and therefore the case must
be detected and avoided. (Fiodor Suietov)
Added an info message whenever an SSDT or OEM table
is loaded dynamically via the Load() or LoadTable()
ASL operators. This should improve debugging capability
since it will show exactly what tables have been loaded
(beyond the tables present in the RSDT/XSDT.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Dock bridges generally do not implement _SUN, yet show up as ejectable
slots. If you have more than one ejectable slot that does not implement
SUN, with the current code you will get duplicate slot numbers. So, if
there is no _SUN, use the current count of the number of slots found
instead.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Modify the acpiphp driver to use the ACPI dock driver for dock
notifications. Only load the acpiphp driver if we find we have pci dock
devices.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Create a driver which lives in the acpi subsystem to handle dock events.
This driver is not an "ACPI" driver, because acpi drivers require that the
object be present when the driver is loaded.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[netdrvr] Remove long-unused bits from Becker template drivers
[netdrvr] natsemi: minor cleanups
[netdrvr] natsemi: Separate out media initialization code
[PATCH] WAN: update info page for a bunch of my drivers
[PATCH] drivers/net/hamradio/dmascc.c: fix section mismatch
[PATCH] Fix phy id for LXT971A/LXT972A
[PATCH] DM9000 - minor code cleanups
[PATCH] DM9000 - do no re-init spin lock
[PATCH] DM9000 - check for MAC left in by bootloader
[PATCH] DM9000 - better checks for platform resources
This patch removes the old pmac ide led blink code and
adds generic LED subsystem support for the LED.
It maintains backward compatibility with the old
BLK_DEV_IDE_PMAC_BLINK Kconfig option which now
simply selects the new code and influences the
default trigger.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 02dd7ae289 ("[PATCH] i2c-i801:
Merge setup function") has a missing return 0 in the _probe() function.
This means the error path is always executed and pci_disable_device() is
called even when the device just got successfully enabled.
Having the SMBus device disabled makes some systems (eg.
Fujitsu-Siemens Lifebook E8010) hang hard during power-off.
Intead of reverting the whole commit this patch fixes it up:
- don't ever call pci_disable_device(), also not in the _remove() function
to avoid hangs
- fix missing pci_release_region() in error path
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Collection of fixes for the ColdFire FEC ethernet driver:
. reworked event setting so that it occurs after the MII setup.
roucaries bastien <roucaries.bastien@gmail.com>
. Do not read cbd_sc in memory for each bit we test. Once per buffer is enough.
. Overrun errors must increase `rx_fifo_errors', not `rx_crc_errors'
. No need for a special value to activate rx or tx. Only write access matters.
. Simplify parameter of eth_copy_and_sum : `data' has already the right value.
. Some spelling fixes.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set different irq priority levels for each IRQ requested.
According to the Freescale ColdFire documentation each separate IRQ
must have its own unique priority/level combination.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the FEC module in the ColdFire 532x CPU family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid requesting a `Graceful Transmit Stop' when link has disappeared,
because that request cannot complete without link.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (26 commits)
V4L/DVB (4263): Fix warning when compiling on 64 bit machines
V4L/DVB (4261): Included required header for in-kernel compilation
V4L/DVB (4260): Stradis.c: make 2 functions static
V4L/DVB (4259): Pass an explicit log prefix to cx2341x_log_status
V4L/DVB (4257): Fix 64-bit compile warnings.
V4L/DVB (4255): Tda9887 default TOP value is 0x10
V4L/DVB (4254): Remove obsoleted tuner_debug option.
V4L/DVB (4253): IVTV VBI format description too long.
V4L/DVB (4252): Remove duplicate 'tda9887' in info messages.
V4L/DVB (4245): Reduce the amount of pvrusb2-sourced noise going into the system log
V4L/DVB (4244): Implement use of cx2341x module in pvrusb2 driver
V4L/DVB (4243): Exploit new V4L control features in pvrusb2
V4L/DVB (4242): Don't suspend encoder when changing its attributes (in pvrusb2)
V4L/DVB (4241): Fix faulty encoder error recovery in pvrusb2
V4L/DVB (4240): Various V4L control enhancements in pvrusb2
V4L/DVB (4239): Handle boolean controls in pvrusb2
V4L/DVB (4238): Make sure flags field is initialized when quering a control in pvrusb2
V4L/DVB (4237): Move LOG_STATUS bracketing to a different part of the pvrusb2 driver
V4L/DVB (4236): Rearrange things in pvrusb2 driver in preparation for using cx2341x module
V4L/DVB (4235): Increase the maximum number of controls that pvrusb2-sysfs.c can handle.
...
DLE masking was non-functional since the new tty handling.
Found by Peter Evertz <leo2@pec.homeip.net>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's available in a header as a static inline - there's no need to export it.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sysfs entries 'sched_mc_power_savings' and 'sched_smt_power_savings' in
/sys/devices/system/cpu/ control the MC/SMT power savings policy for the
scheduler.
Based on the values (1-enable, 0-disable) for these controls, sched groups
cpu power will be determined for different domains. When power savings
policy is enabled and under light load conditions, scheduler will minimize
the physical packages/cpu cores carrying the load and thus conserving
power(with a perf impact based on the workload characteristics... see OLS
2005 CMP kernel scheduler paper for more details..)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Con Kolivas <kernel@kolivas.org>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace the temp makefile hacks with proper CONFIG entries, which are also
added to Kconfig.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add current pin settings to gpio_dump() output. This adds the last 'word' to
the syslog lines, which displays the input and output values that the pin is
set to.
pc8736x_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE io:1/1
The 2 values may differ for a number of reasons:
1- the pin output circuitry is diaabled, (as the above 'TS' indicates)
2- it needs a pullup resistor to drive the attached circuit,
3- the external circuit needs a pullup so the open-drain has something
to pull-down
4- the pin is wired to Vcc or Ground
It might be appropriate to add a WARN for 2,3,4, since they could
damage the chip and/or circuit, esp if misconfig goes unnoticed.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hmm. Im somewhat ambivalent about this patch, since with it, driver wont
build for vanilla 17 or older.
Its also only 1/2 of your suggestion - when I tried it, I was building against
vanilla 17, and asm/uaccess.h cause compilation failure. Looking back, Im
perplexed as to why linux/io.h didnt cause same failure ?!?
use linux/io.h rather than asm/io.h
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace spinlocks guarding gpio config ops with mutexes. This is a me-too
patch, and is justifiable insofar as mutexes have stricter semantics and
better debugging support, so are preferred where they are applicable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a working gpio_current() to pc8736x_gpio.c (the previous implementation
just threw a dev_warn), and fix gpio_change() to use gpio_current() rather
than the incorrect (and temporary) gpio_get(). Initialize shadow-regs so this
all works.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of dev_dbg() and friends is considered good practice. dev_dbg() needs a
struct device *devp, but nsc_gpio is only a helper module, so it doesnt
have/need its own. To provide devp to the user-modules (scx200 & pc8736x
_gpio), we add it to the vtable, and set it during init.
Also squeeze nsc_gpio_dump()'s format a little.
[ 199.259879] pc8736x_gpio.0: io09: 0x0044 TS OD PUE EDGE LO DEBOUNCE
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds platform-device to (just introduced) driver, and uses it to replace many
printks with dev_dbg() etc. This could trivially be merged into previous
patch, but this way matches better with the corresponding patch that does the
same change to scx200_gpio.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the brand new pc8736x_gpio driver. This is mostly based upon
scx200_gpio.c, but the platform_dev is treated separately, since its fairly
big too.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the meaning of config-bits is the same for scx200 and pc8736x _gpios, we
can share a function to deliver this to user. Since it is called via the
vtable, its also completely replaceable. For now, we keep using printk...
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that the read(), write() file-ops are dispatching gpio-ops via the vtable,
they are generic, and can be moved 'verbatim' to the nsc_gpio common-support
module. After the move, various symbols are renamed to update 'scx200_' to
'nsc_', and headers are adjusted accordingly.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the nsc_gpio common-support module as an empty shell. Next patch starts
the migration of the common gpio support routines.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now actually call the gpio operations thru the vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Abstract the gpio operations into a new nsc_gpio_ops vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new driver command: 'v' which calls gpio_dump() on the pin. The output
goes to the log, like all other INFO messages in the original driver. Giving
the user control over the feedback they 'need' is construed to be a
user-friendly feature, and allows us (later) to dial down many INFO messages
to DEBUG log-level.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a platform-device to scx200_gpio, and use its struct device dev member
(ie: devp) in dev_dbg() once.
There are 2 alternatives here (Im soliciting guidance/commentary):
- use isa_device, if/when its added to the kernel.
- alter scx200.c to EXPORT_GPL its private devp so that both scx200_gpio,
and the (to be added) nsc_gpio module can use it. Since the available devp
is in 'grandparent', this seems like too much 'action at a distance'.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adopt many modern 2.6 coding practices, ala LDD3, chapter 3. Changes are
limited to initialization calls from module init, ie: cdev_init, cdev_add,
*_chrdev_region, mkdev.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO SUPPORT FOR SCx200 & PC8736x
The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and
refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x
chips. Its handy for the Soekris.com net-4801, which has both chips.
These patches have been seen recently on Kernel-Mentors, and then
Kernel-Newbies ML, where Jesper Juhl kindly reviewed it. His feedback has
been incorporated. Thanks Jesper !
Its also gone to soekris-tech@soekris.com for possible testing by linux folks,
I've gotten 1 promise so far. Theyre mostly BSD folk over there, but we'll
see..
Device-file & Sysfs
The driver preserves the existing device-file interface, including the
write/cmd set, but adds v to 'view' the pin-settings & configs by inducing,
via gpio_dump(), a dev_info() call. Its a fairly crappy way to get status,
but it sticks to the syslog approach, conservatively.
Allowing users to voluntarily trigger logging is good, it gives them a
familiar way to confirm their app's control & use of the pins, and I've thus
reduced the pin-mode-updates from dev_info to dev_dbg.
I've recently bolted on a proto sysfs interface for both new drivers. Im not
including those patches here; they (the patch + doc-pre-patch) are still quite
raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a
proper vetting is needed. Since this patchset is much bigger than my previous
ones, Id like to keep things simpler, and address it 1st, before bolting on
more stuff.
The driver-split
The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a
common pin-architecture (same pin features, with same bits controlling), but
with different addressing mechanics and port organizations.
The vintage driver expresses the pin capabilities with pin-mode commands
[OoPpTt],etc that change the pin configurations, and since the 2 chips share
pin-arch, we can reuse the read(), write() commands, once the implementation
is suitably adjusted.
The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio
operations, then adjusts fileops.write() code to invoke operations via that
vtable. Driver specific open()s set private_data to the vtable so its
available for use by write().
The vtable gets the gpio_dump() too, since its user-friendly, and (could be
construed as) part of the current device-file interface. To support use of
dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both
scx200 & pc8736x _gpio drivers.
heres how the pins are presented in syslog:
[ 1890.176223] scx200_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE
[ 1890.287223] scx200_gpio.0: io01: 0x0003 OE PP PUD EDGE LO
nsc_gpio.c: new file is new home of several file-ops methods, which are
modified to get their vtable from filp->private_data, and use it where needed.
scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up
via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this
vtable). A driver-spcific open() initializes filp->private_data with the
vtable.
Once the split is clean, and the scx200_gpio driver is working, we copy and
modify the function and variable names, and rework the access-method bodies
for the different addressing scheme.
Heres a working overview of the patchset:
# series file for GPIO
# Spring Cleaning
gpio-scx/patch.preclean # scripts/Lindent fixes, editor-ctrl comments
# API Modernization
gpio-scx/patch.api26 # what I learned from LDD3
gpio-scx/patch.platform-dev-2 # get pdev, support for dev_dbg()
gpio-scx/patch.unsigned-minor # fix to match std practice
# Debuggability
gpio-scx/patch.dump-diet # shrink gpio_dump()
gpio-scx/patch.viewpins # add new 'command' to call dump()
gpio-scx/patch.init-refactor # pull shadow-register init to sub
# Access-Abstraction (add vtable)
gpio-scx/patch.access-vtable # introduce nsg_gpio_ops vtable, w dump
gpio-scx/patch.vtable-calls # add & use the vtable in scx200_gpio
gpio-scx/patch.nscgpio-shell # add empty driver for common-fops
# move code under abstraction
gpio-scx/patch.migrate-fops # move file-ops methods from scx200_gpio
gpio-scx/patch.common-dump # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c
gpio-scx/patch.add-pc8736x-gpio # add new driver, like old, w chip adapt
# gpio-scx/patch.add-DEBUG # enable all dev_dbg()s
# Cleanups
# finish printk -> dev_dbg() etc
gpio-scx/patch.pdev-pc8736x # new drvr needs pdev too,
gpio-scx/patch.devdbg-nscgpio # add device to 'vtable', use in dev_dbg()
# gpio-scx/patch.pin-config-view # another 'c' 'command'
# gpio-scx/quiet-getset # take out excess dbg stuff (pretty quiet
now)
gpio-scx/patch.shadow-current # imitate scx200_gpio's shadow regs in
pc87*
# post KMentors-post patches ..
gpio-scx/patch.mutexes # use mutexes for config-locks
gpio-scx/patch.viewpins-values # extend dump to obsolete separate 'c' cmd
gpio-scx/patch.kconfig # add stuff for kbuild
# TBC
# combine api26 with pdev, which is just one step.
# merge c&v commands to single do-all-fn
# delay viewpins, dump-diet should also un-ifdef it too.
diff.sys-gpio-rollup-1
This patch:
Removed editor format-control comments, and used scripts/Lindent to clean up
whitespace, then deleted the bogus chunks :-(
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CPUs come online only at init time (unless CONFIG_HOTPLUG_CPU is defined).
So, cpu_notifier functionality need to be available only at init time.
This patch makes register_cpu_notifier() available only at init time, unless
CONFIG_HOTPLUG_CPU is defined.
This patch exports register_cpu_notifier() and unregister_cpu_notifier() only
if CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to serialize access to the global rtc_idr even in this error path.
Signed-off-by: Sonny Rao <sonny@burdell.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
