The NAND rework resulted in non ECC based reads. Fix it up and
do a bit of cleanup while at it.
Pointed out by Adrian Bunk.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While trying to look for superfluous I/O accesses that can be optimized
away, I stumbled upon this ACPI sleep I/O access and couldn't figure out
why the hell this dummy op was necessary.
After more than one hour of internet research, I had collected a sufficient
number of documents (among those very old kernel versions) that finally
told me what this dummy read was about: STPCLK# doesn't get asserted in time
on (some) chipsets, which is why we need to have a dummy I/O read to delay
further instruction processing until the CPU is fully stopped.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Only if bus master activity is going on at the present, we should avoid
entering C3-type sleep, as it might be a faulty transition. As long as the
bm_activity bitmask was based on the number of calls to the ACPI idle
function, looking at previous moments made sense. Now, with it being based on
what happened this jiffy, looking at this jiffy should be sufficient.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Do not assume there was bus mastering activity if the idle handler didn't get
called, as there's only reason to not enter C3-type sleep if there is bus
master activity going on. Only for the "promotion" into C3-type sleep bus
mastering activity is taken into account, and there only current bus mastering
activity, and not pure guessing should lead to the decision on whether to
enter C3-type sleep or not.
Also, as bm_activity is a jiffy-based bitmask (bit 0: bus mastering activity
during this juffy, bit 31: bus mastering activity 31 jiffies ago), fix the
setting of bit 0, as it might be called multiple times within one jiffy.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Track the actual time spent in C-States (C2 upwards, we can't determine this
for C1), not only the number of invocations. This is especially useful for
dynamic ticks / "tickless systems", but is also of interest on normal systems,
as any interrupt activity leads to C-States being exited, not only the timer
interrupt.
The time is being measured in PM timer ticks, so an increase by one equals 279
nanoseconds.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented a new acpi_spinlock type for the OSL lock
interfaces. This allows the type to be customized to
the host OS for improved efficiency (since a spinlock is
usually a very small object.)
Implemented support for "ignored" bits in the ACPI
registers. According to the ACPI specification, these
bits should be preserved when writing the registers via
a read/modify/write cycle. There are 3 bits preserved
in this manner: PM1_CONTROL[0] (SCI_EN), PM1_CONTROL[9],
and PM1_STATUS[11].
http://bugzilla.kernel.org/show_bug.cgi?id=3691
Implemented the initial deployment of new OSL mutex
interfaces. Since some host operating systems have
separate mutex and semaphore objects, this feature was
requested. The base code now uses mutexes (and the new
mutex interfaces) wherever a binary semaphore was used
previously. However, for the current release, the mutex
interfaces are defined as macros to map them to the
existing semaphore interfaces.
Fixed several problems with the support for the control
method SyncLevel parameter. The SyncLevel now works
according to the ACPI specification and in concert with the
Mutex SyncLevel parameter, since the current SyncLevel is
a property of the executing thread. Mutual exclusion for
control methods is now implemented with a mutex instead
of a semaphore.
Fixed three instances of the use of the C shift operator
in the bitfield support code (exfldio.c) to avoid the use
of a shift value larger than the target data width. The
behavior of C compilers is undefined in this case and can
cause unpredictable results, and therefore the case must
be detected and avoided. (Fiodor Suietov)
Added an info message whenever an SSDT or OEM table
is loaded dynamically via the Load() or LoadTable()
ASL operators. This should improve debugging capability
since it will show exactly what tables have been loaded
(beyond the tables present in the RSDT/XSDT.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Dock bridges generally do not implement _SUN, yet show up as ejectable
slots. If you have more than one ejectable slot that does not implement
SUN, with the current code you will get duplicate slot numbers. So, if
there is no _SUN, use the current count of the number of slots found
instead.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Modify the acpiphp driver to use the ACPI dock driver for dock
notifications. Only load the acpiphp driver if we find we have pci dock
devices.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Create a driver which lives in the acpi subsystem to handle dock events.
This driver is not an "ACPI" driver, because acpi drivers require that the
object be present when the driver is loaded.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[netdrvr] Remove long-unused bits from Becker template drivers
[netdrvr] natsemi: minor cleanups
[netdrvr] natsemi: Separate out media initialization code
[PATCH] WAN: update info page for a bunch of my drivers
[PATCH] drivers/net/hamradio/dmascc.c: fix section mismatch
[PATCH] Fix phy id for LXT971A/LXT972A
[PATCH] DM9000 - minor code cleanups
[PATCH] DM9000 - do no re-init spin lock
[PATCH] DM9000 - check for MAC left in by bootloader
[PATCH] DM9000 - better checks for platform resources
This patch removes the old pmac ide led blink code and
adds generic LED subsystem support for the LED.
It maintains backward compatibility with the old
BLK_DEV_IDE_PMAC_BLINK Kconfig option which now
simply selects the new code and influences the
default trigger.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 02dd7ae289 ("[PATCH] i2c-i801:
Merge setup function") has a missing return 0 in the _probe() function.
This means the error path is always executed and pci_disable_device() is
called even when the device just got successfully enabled.
Having the SMBus device disabled makes some systems (eg.
Fujitsu-Siemens Lifebook E8010) hang hard during power-off.
Intead of reverting the whole commit this patch fixes it up:
- don't ever call pci_disable_device(), also not in the _remove() function
to avoid hangs
- fix missing pci_release_region() in error path
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Collection of fixes for the ColdFire FEC ethernet driver:
. reworked event setting so that it occurs after the MII setup.
roucaries bastien <roucaries.bastien@gmail.com>
. Do not read cbd_sc in memory for each bit we test. Once per buffer is enough.
. Overrun errors must increase `rx_fifo_errors', not `rx_crc_errors'
. No need for a special value to activate rx or tx. Only write access matters.
. Simplify parameter of eth_copy_and_sum : `data' has already the right value.
. Some spelling fixes.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set different irq priority levels for each IRQ requested.
According to the Freescale ColdFire documentation each separate IRQ
must have its own unique priority/level combination.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the FEC module in the ColdFire 532x CPU family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid requesting a `Graceful Transmit Stop' when link has disappeared,
because that request cannot complete without link.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (26 commits)
V4L/DVB (4263): Fix warning when compiling on 64 bit machines
V4L/DVB (4261): Included required header for in-kernel compilation
V4L/DVB (4260): Stradis.c: make 2 functions static
V4L/DVB (4259): Pass an explicit log prefix to cx2341x_log_status
V4L/DVB (4257): Fix 64-bit compile warnings.
V4L/DVB (4255): Tda9887 default TOP value is 0x10
V4L/DVB (4254): Remove obsoleted tuner_debug option.
V4L/DVB (4253): IVTV VBI format description too long.
V4L/DVB (4252): Remove duplicate 'tda9887' in info messages.
V4L/DVB (4245): Reduce the amount of pvrusb2-sourced noise going into the system log
V4L/DVB (4244): Implement use of cx2341x module in pvrusb2 driver
V4L/DVB (4243): Exploit new V4L control features in pvrusb2
V4L/DVB (4242): Don't suspend encoder when changing its attributes (in pvrusb2)
V4L/DVB (4241): Fix faulty encoder error recovery in pvrusb2
V4L/DVB (4240): Various V4L control enhancements in pvrusb2
V4L/DVB (4239): Handle boolean controls in pvrusb2
V4L/DVB (4238): Make sure flags field is initialized when quering a control in pvrusb2
V4L/DVB (4237): Move LOG_STATUS bracketing to a different part of the pvrusb2 driver
V4L/DVB (4236): Rearrange things in pvrusb2 driver in preparation for using cx2341x module
V4L/DVB (4235): Increase the maximum number of controls that pvrusb2-sysfs.c can handle.
...
DLE masking was non-functional since the new tty handling.
Found by Peter Evertz <leo2@pec.homeip.net>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's available in a header as a static inline - there's no need to export it.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sysfs entries 'sched_mc_power_savings' and 'sched_smt_power_savings' in
/sys/devices/system/cpu/ control the MC/SMT power savings policy for the
scheduler.
Based on the values (1-enable, 0-disable) for these controls, sched groups
cpu power will be determined for different domains. When power savings
policy is enabled and under light load conditions, scheduler will minimize
the physical packages/cpu cores carrying the load and thus conserving
power(with a perf impact based on the workload characteristics... see OLS
2005 CMP kernel scheduler paper for more details..)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Con Kolivas <kernel@kolivas.org>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace the temp makefile hacks with proper CONFIG entries, which are also
added to Kconfig.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add current pin settings to gpio_dump() output. This adds the last 'word' to
the syslog lines, which displays the input and output values that the pin is
set to.
pc8736x_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE io:1/1
The 2 values may differ for a number of reasons:
1- the pin output circuitry is diaabled, (as the above 'TS' indicates)
2- it needs a pullup resistor to drive the attached circuit,
3- the external circuit needs a pullup so the open-drain has something
to pull-down
4- the pin is wired to Vcc or Ground
It might be appropriate to add a WARN for 2,3,4, since they could
damage the chip and/or circuit, esp if misconfig goes unnoticed.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hmm. Im somewhat ambivalent about this patch, since with it, driver wont
build for vanilla 17 or older.
Its also only 1/2 of your suggestion - when I tried it, I was building against
vanilla 17, and asm/uaccess.h cause compilation failure. Looking back, Im
perplexed as to why linux/io.h didnt cause same failure ?!?
use linux/io.h rather than asm/io.h
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace spinlocks guarding gpio config ops with mutexes. This is a me-too
patch, and is justifiable insofar as mutexes have stricter semantics and
better debugging support, so are preferred where they are applicable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a working gpio_current() to pc8736x_gpio.c (the previous implementation
just threw a dev_warn), and fix gpio_change() to use gpio_current() rather
than the incorrect (and temporary) gpio_get(). Initialize shadow-regs so this
all works.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of dev_dbg() and friends is considered good practice. dev_dbg() needs a
struct device *devp, but nsc_gpio is only a helper module, so it doesnt
have/need its own. To provide devp to the user-modules (scx200 & pc8736x
_gpio), we add it to the vtable, and set it during init.
Also squeeze nsc_gpio_dump()'s format a little.
[ 199.259879] pc8736x_gpio.0: io09: 0x0044 TS OD PUE EDGE LO DEBOUNCE
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds platform-device to (just introduced) driver, and uses it to replace many
printks with dev_dbg() etc. This could trivially be merged into previous
patch, but this way matches better with the corresponding patch that does the
same change to scx200_gpio.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the brand new pc8736x_gpio driver. This is mostly based upon
scx200_gpio.c, but the platform_dev is treated separately, since its fairly
big too.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the meaning of config-bits is the same for scx200 and pc8736x _gpios, we
can share a function to deliver this to user. Since it is called via the
vtable, its also completely replaceable. For now, we keep using printk...
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that the read(), write() file-ops are dispatching gpio-ops via the vtable,
they are generic, and can be moved 'verbatim' to the nsc_gpio common-support
module. After the move, various symbols are renamed to update 'scx200_' to
'nsc_', and headers are adjusted accordingly.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the nsc_gpio common-support module as an empty shell. Next patch starts
the migration of the common gpio support routines.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now actually call the gpio operations thru the vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Abstract the gpio operations into a new nsc_gpio_ops vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new driver command: 'v' which calls gpio_dump() on the pin. The output
goes to the log, like all other INFO messages in the original driver. Giving
the user control over the feedback they 'need' is construed to be a
user-friendly feature, and allows us (later) to dial down many INFO messages
to DEBUG log-level.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a platform-device to scx200_gpio, and use its struct device dev member
(ie: devp) in dev_dbg() once.
There are 2 alternatives here (Im soliciting guidance/commentary):
- use isa_device, if/when its added to the kernel.
- alter scx200.c to EXPORT_GPL its private devp so that both scx200_gpio,
and the (to be added) nsc_gpio module can use it. Since the available devp
is in 'grandparent', this seems like too much 'action at a distance'.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adopt many modern 2.6 coding practices, ala LDD3, chapter 3. Changes are
limited to initialization calls from module init, ie: cdev_init, cdev_add,
*_chrdev_region, mkdev.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO SUPPORT FOR SCx200 & PC8736x
The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and
refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x
chips. Its handy for the Soekris.com net-4801, which has both chips.
These patches have been seen recently on Kernel-Mentors, and then
Kernel-Newbies ML, where Jesper Juhl kindly reviewed it. His feedback has
been incorporated. Thanks Jesper !
Its also gone to soekris-tech@soekris.com for possible testing by linux folks,
I've gotten 1 promise so far. Theyre mostly BSD folk over there, but we'll
see..
Device-file & Sysfs
The driver preserves the existing device-file interface, including the
write/cmd set, but adds v to 'view' the pin-settings & configs by inducing,
via gpio_dump(), a dev_info() call. Its a fairly crappy way to get status,
but it sticks to the syslog approach, conservatively.
Allowing users to voluntarily trigger logging is good, it gives them a
familiar way to confirm their app's control & use of the pins, and I've thus
reduced the pin-mode-updates from dev_info to dev_dbg.
I've recently bolted on a proto sysfs interface for both new drivers. Im not
including those patches here; they (the patch + doc-pre-patch) are still quite
raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a
proper vetting is needed. Since this patchset is much bigger than my previous
ones, Id like to keep things simpler, and address it 1st, before bolting on
more stuff.
The driver-split
The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a
common pin-architecture (same pin features, with same bits controlling), but
with different addressing mechanics and port organizations.
The vintage driver expresses the pin capabilities with pin-mode commands
[OoPpTt],etc that change the pin configurations, and since the 2 chips share
pin-arch, we can reuse the read(), write() commands, once the implementation
is suitably adjusted.
The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio
operations, then adjusts fileops.write() code to invoke operations via that
vtable. Driver specific open()s set private_data to the vtable so its
available for use by write().
The vtable gets the gpio_dump() too, since its user-friendly, and (could be
construed as) part of the current device-file interface. To support use of
dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both
scx200 & pc8736x _gpio drivers.
heres how the pins are presented in syslog:
[ 1890.176223] scx200_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE
[ 1890.287223] scx200_gpio.0: io01: 0x0003 OE PP PUD EDGE LO
nsc_gpio.c: new file is new home of several file-ops methods, which are
modified to get their vtable from filp->private_data, and use it where needed.
scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up
via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this
vtable). A driver-spcific open() initializes filp->private_data with the
vtable.
Once the split is clean, and the scx200_gpio driver is working, we copy and
modify the function and variable names, and rework the access-method bodies
for the different addressing scheme.
Heres a working overview of the patchset:
# series file for GPIO
# Spring Cleaning
gpio-scx/patch.preclean # scripts/Lindent fixes, editor-ctrl comments
# API Modernization
gpio-scx/patch.api26 # what I learned from LDD3
gpio-scx/patch.platform-dev-2 # get pdev, support for dev_dbg()
gpio-scx/patch.unsigned-minor # fix to match std practice
# Debuggability
gpio-scx/patch.dump-diet # shrink gpio_dump()
gpio-scx/patch.viewpins # add new 'command' to call dump()
gpio-scx/patch.init-refactor # pull shadow-register init to sub
# Access-Abstraction (add vtable)
gpio-scx/patch.access-vtable # introduce nsg_gpio_ops vtable, w dump
gpio-scx/patch.vtable-calls # add & use the vtable in scx200_gpio
gpio-scx/patch.nscgpio-shell # add empty driver for common-fops
# move code under abstraction
gpio-scx/patch.migrate-fops # move file-ops methods from scx200_gpio
gpio-scx/patch.common-dump # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c
gpio-scx/patch.add-pc8736x-gpio # add new driver, like old, w chip adapt
# gpio-scx/patch.add-DEBUG # enable all dev_dbg()s
# Cleanups
# finish printk -> dev_dbg() etc
gpio-scx/patch.pdev-pc8736x # new drvr needs pdev too,
gpio-scx/patch.devdbg-nscgpio # add device to 'vtable', use in dev_dbg()
# gpio-scx/patch.pin-config-view # another 'c' 'command'
# gpio-scx/quiet-getset # take out excess dbg stuff (pretty quiet
now)
gpio-scx/patch.shadow-current # imitate scx200_gpio's shadow regs in
pc87*
# post KMentors-post patches ..
gpio-scx/patch.mutexes # use mutexes for config-locks
gpio-scx/patch.viewpins-values # extend dump to obsolete separate 'c' cmd
gpio-scx/patch.kconfig # add stuff for kbuild
# TBC
# combine api26 with pdev, which is just one step.
# merge c&v commands to single do-all-fn
# delay viewpins, dump-diet should also un-ifdef it too.
diff.sys-gpio-rollup-1
This patch:
Removed editor format-control comments, and used scripts/Lindent to clean up
whitespace, then deleted the bogus chunks :-(
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CPUs come online only at init time (unless CONFIG_HOTPLUG_CPU is defined).
So, cpu_notifier functionality need to be available only at init time.
This patch makes register_cpu_notifier() available only at init time, unless
CONFIG_HOTPLUG_CPU is defined.
This patch exports register_cpu_notifier() and unregister_cpu_notifier() only
if CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to serialize access to the global rtc_idr even in this error path.
Signed-off-by: Sonny Rao <sonny@burdell.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two locking sets involved. One locks the board mappings and the
other is the tty open/close locking. The low level code was clearly
designed to be ported to OS's with spin locks already so pretty much comes
out in the wash
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Corey Minyard <minyard@acm.org>
The kthread used to speed up polling for IPMI was using udelay in its
busy-wait polling loop when the lower-level state machine told it to do a
short delay. This just used CPU and didn't help scheduling, thus causing
bad problems with other tasks. Call schedule() instead.
Signed-off-by: Corey Minyard <minyard@acm.org>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix TCSBRK comment to prevent confusion or accidental removal.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update two drivers to use poison.h.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Localize poison values into one header file for better documentation and
easier/quicker debugging and so that the same values won't be used for
multiple purposes.
Use these constants in core arch., mm, driver, and fs code.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Goto-san's patch, we can add new pgdat/node at runtime. I'm now
considering node-hot-add with cpu + memory on ACPI.
I found acpi container, which describes node, could evaluate cpu before
memory. This means cpu-hot-add occurs before memory hot add.
In most part, cpu-hot-add doesn't depend on node hot add. But register_cpu(),
which creates symbolic link from node to cpu, requires that node should be
onlined before register_cpu(). When a node is onlined, its pgdat should be
there.
This patch-set holds off creating symbolic link from node to cpu
until node is onlined.
This removes node arguments from register_cpu().
Now, register_cpu() requires 'struct node' as its argument. But the array of
struct node is now unified in driver/base/node.c now (By Goto's node hotplug
patch). We can get struct node in generic way. So, this argument is not
necessary now.
This patch also guarantees add cpu under node only when node is onlined. It
is necessary for node-hot-add vs. cpu-hot-add patch following this.
Moreover, register_cpu calculates cpu->node_id by cpu_to_node() without regard
to its 'struct node *root' argument. This patch removes it.
Also modify callers of register_cpu()/unregister_cpu, whose args are changed
by register-cpu-remove-node-struct patch.
[Brice.Goglin@ens-lyon.org: fix it]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When new node becomes enable by hot-add, new sysfs file must be created for
new node. So, if new node is enabled by add_memory(), register_one_node() is
called to create it. In addition, I386's arch_register_node() and a part of
register_nodes() of powerpc are consolidated to register_one_node() as a
generic_code().
This is tested by Tiger4(IPF) with node hot-plug emulation.
Signed-off-by: Keiichiro Tokunaga <tokuanga.keiich@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is to find node id from acpi's handle of memory_device in DSDT. _PXM for
the new node can be found by acpi_get_pxm() by using new memory's handle. So,
node id can be found by pxm_to_nid_map[].
This patch becomes simpler than v2 of node hot-add patch.
Because old add_memory() function doesn't have node id parameter.
So, kernel must find its handle by physical address via DSDT again.
But, v3 just give node id to add_memory() now.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name of old add_memory() to arch_add_memory. And use node id to
get pgdat for the node at NODE_DATA().
Note: Powerpc's old add_memory() is defined as __devinit. However,
add_memory() is usually called only after bootup.
I suppose it may be redundant. But, I'm not well known about powerpc.
So, I keep it. (But, __meminit is better at least.)
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When acpi_memory_device_init() is called at boottime to register struct
memory acpi_memory_device, acpi_bus_add() are called via
acpi_driver_attach().
But it also calls ops->start() function. It is called even if the memory
blocks are initialized at early boottime. In this case add_memory() return
-EEXIST, and the memory blocks becomes INVALID state even if it is normal.
This is patch to avoid calling add_memory() for already available memory.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch to call add_memroy() when notify reaches for new node's add
event.
When new node is added, notify of ACPI reaches container device which means
the node.
Container device driver calls acpi_bus_scan() to find and add belonging
devices (which means cpu, memory and so on). Its function calls add and
start function of belonging devices's driver.
Howevever, current memory hotplug driver just register add function to
create sysfs file for its memory. But, acpi_memory_enable_device() is not
called because it is considered just the case that notify reaches memory
device directly. So, if notify reaches container device nothing can call
add_memory().
This is a patch to create start function which calls add_memory().
add_memory() can be called by this when notify reaches container device.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current acpi memory hotplug just looks into the first entry of resources in
_CRS. But, _CRS can contain plural resources. So, if _CRS contains plural
resoureces, acpi memory hot add cannot add all memory.
With this patch, acpi memory hotplug can deal with Memory Device, whose
_CRS contains plural resources.
Tested on ia64 memory hotplug test envrionment (not emulation, uses alpha
version firmware which supports dynamic reconfiguration of NUMA.)
Note: Microsoft's Windows Server 2003 requires big (>4G)resoureces to be
divided into small (<4G) resources. looks crazy, but not invalid.
(See http://www.microsoft.com/whdc/system/pnppwr/hotadd/hotaddmem.mspx)
For this reason, a firmware vendor who supports Windows writes plural
resources in a _CRS even if they are contiguous.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a helper to asm/pdc.h to translate OS_ID values to strings
and use it in the pdc_stable driver.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
We were assigned an OS_ID of 0x0006. Consistently use OS_ID_LINUX
instead of using the magic number. Also update the OS_ID_ defines in
asm/pdc.h to reflect this.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
pdc_stable v0.30:
This patch introduces 3 more files to the /sys/firmware/stable tree:
- diagnostic, which contains a cryptic hex string
- osdep1, a 16 bytes os-dependent storage area always available
- osdep2, another os-dependent storage area which existence/size depends
on hversion.
This patch also adds code to setup the "Linux" signature in stable
storage. That is to say that starting with this patch, the kernel will
now sign its OSID (0x0006, thx LaMont) in Stable Storage upon boot,
whether pdc_stable is enabled or not.
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch removes a limitation of the original code, so that CHASSIS
codes can be sent to all machines. On machines with a LCD panel, this
code displays "INI" during bootup, "RUN" when the system is booted and
running, "FLT" when a panic occurs, etc.
This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS
This patch also adds minimalistic support for Chassis warnings, through
a proc entry '/proc/chassis', which will reflect the warnings status (PSU
or fans failure when they happen, NVRAM battery level and temperature
thresholds overflows).
This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS_WARN
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Some debugging code in sba_iommu.c should be testing ioc_needs_fdc,
not directly testing boot_cpu_data.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Clean up gcc 4.1 warnings noted by Joel Soete.
Kyle McMartin gets kudos for pointing out the issues.
Matthew Wilcox noticed sba_iommu was using open coded versions
of (read|write)X.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The other way round works not really well with boards which have a
static NAND chipselect.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Allow lseek(mtdchar_fd, 0, SEEK_END) to succeed, which currently fails
with EINVAL.
lseek(fd, 0, SEEK_END) should result into the same fileposition as
lseek(fd, 0, SEEK_SET) + read(fd, buf, length(fd))
Furthermore, lseek(fd, 0, SEEK_CUR) should return the current file position,
which in case of an encountered EOF should not result in EINVAL
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I was unable to compile ts7250.c after your refactor commit,
it's a typo probably.
-- ynezz
From: Petr Stetiar <ynezz@true.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It should be done before calling class_device_unregister() because
it will destroy the device and free memory if there are no other
references to the device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on an original patch from Ralf Baechle <ralf@linux-mips.org> and
Vivek Goyal <vgoyal@in.ibm.com>. This is needed in order to prepare for
changing the size of resources.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original post was incorrect as it didn't realize that we already had
a self-referenc due to device_initialize(), and we were really only
missing the put on our own reference. This was hidden by the other bug
which had the midlayer reusing stargets after they were already free,
which was doing too many puts on our rport.
Updating FC transport for:
- Add put in fc_rport_final_delete(), to release the rport.
Prior, we were leaving the rport with a reference, thus the shost
with references, etc. If the driver was unloaded, shosts and rports
remained, along with work threads, etc
- Fix fc_rport_create failure path - too many put's on parent
- Add commenting to easily track ref taking.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Updated patch to address comments from Pat Mansfield and Michael Reed:
Bumped max to 600 (10mins). Set default dev_loss_tmo to a value other
than the max (30s).
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In a prior posting to linux-scsi on the fc transport and workq
deadlocks, we noted a second error that did not have a patch:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114467847711383&w=2
- There's a deadlock where scsi_remove_target() has to sit behind
scsi_scan_target() due to contention over the scan_lock().
Subsequently we posted a request for comments about the deadlock:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114469358829500&w=2
This posting resolves the second error. Here's what we now understand,
and are implementing:
If the lldd deletes the rport while a scan is active, the sdev's queue
is blocked which stops the issuing of commands associated with the scan.
At this point, the scan stalls, and does so with the shost->scan_mutex held.
If, at this point, if any scan or delete request is made on the host, it
will stall waiting for the scan_mutex.
For the FC transport, we queue all delete work to a single workq.
So, things worked fine when competing with the scan, as long as the
target blocking the scan was the same target at the top of our delete
workq, as the delete workq routine always unblocked just prior to
requesting the delete. Unfortunately, if the top of our delete workq
was for a different target, we deadlock. Additionally, if the target
blocking scan returned, we were unblocking it in the scan workq routine,
which really won't execute until the existing stalled scan workq
completes (e.g. we're re-scheduling it while it is in the midst of its
execution).
This patch moves the unblock out of the workq routines and moves it to
the context that is scheduling the work. This ensures that at some point,
we will unblock the target that is blocking scan. Please note, however,
that the deadlock condition may still occur while it waits for the
transport to timeout an unblock on a target. Worst case, this is bounded
by the transport dev_loss_tmo (default: 30 seconds).
Finally, Michael Reed deserves the credit for the bulk of this patch,
analysis, and it's testing. Thank you for your help.
Note: The request for comments statements about the gross-ness of the
scan_mutex still stand.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This removes the duplicate functionality which had been added to
the lpfc driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The scsi midlayer portion of the patch
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a simple off-by-one error in the mtd physmap driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for both the S3C2412 and S3C2412 Samsung SoCs to
the increasingly mis-named s3c2410.c driver.
This currently only supports SLC ECCs, and a chip on nFCE0.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Wistron MS 2111 (aka Medion 'Titanium' MD 9783, aka ALDI PC,
aka Fujitsu-Siemens AMILO D7800, aka ...) has 5 extra buttons,
map them. Unfortunately we only have DMI data for the Medion
box.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
print kobj name in this message.
lenb changed to use printk.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The ASL Acquire operator (17.5.1 in ACPI 3.0 spec) is allowed to time out
and return True without acquiring the semaphore. There's no indication in
the spec that this is an actual error, so this message should be
debug-only, as the message for successful acquisition is.
This used to be an ACPI_DEBUG_PRINT, but it was mis-classified as
ACPI_DB_ERROR rather than ACPI_DB_MUTEX, so it got swept up in Thomas'
recent patch to enable ACPI error messages even without CONFIG_ACPI_DEBUG.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Symbols such as PCI_USES_IO, PCI_ADDR0, etc. originated from Donald
Becker's net driver template, but have been long unused. Remove.
In a few drivers, this allows the further eliminate of the pci_flags (or
just plain flags) member in the template driver probe structure.
Most of this logic is simply open-coded in most drivers, since it never
changes.
Made a few other cleanups while I was in there, too:
* constify, __devinitdata several PCI ID tables
* replace table terminating entries such as "{0,}," and "{NULL},"
with a more-clean "{ }".
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A card number is not unique enough. Instead, let the caller specify the
prefix of the status messages.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For most tuners the default TOP value is 0x10, regardless of TV norm.
So revert earlier change that sets the TOP value to 0x14 for PAL/SECAM.
This is incorrect.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Format description was cut off. It's been shortened.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the duplicate '(tda9887)' in these messages:
tda9887 8-0043 (tda9887): tda988[5/6/7] found @ 0x43 (tuner)
The same string is already printed as the prefix in this line.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
implemented VIDIOC_LOG_STATUS in the cx88-blackbird driver
to show the status of i2c clients and the cx23416 mpeg encoder.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement V4L2 driver for the Hauppauge PVR USB2 TV tuner.
The Hauppauge PVR USB2 is a USB connected TV tuner with an embedded
cx23416 hardware MPEG2 encoder. There are two major variants of this
device; this driver handles both. Any V4L2 application which
understands MPEG2 video stream data should be able to work with this
device.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* make eeprom size a variable, prepping for future patch
* eliminate unused PCI_xxx stuff left over from Becker driver template
* convert a few #defines to enum
* mark PCI table const, __devinitdata
* don't bother with named constant for PCI device id
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updates generic HDLC info page address, I should have done it
long time ago.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
dev_setup() is using the __initdata variables ax25_broadcast and
ax25_test.
Since the only caller of dev_setup() (setup_adapter()) is already
__init, the solution is to make dev_setup() __init, too.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
The phy ids used are taken from an driver that used a right shift of 4 to chop
off the revision number. This driver does not shift, so the id and mask
values are wrong and must be left shifted by 4 to actually detect the chips.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Acked-by: Andy Fleming <afleming@freescale.com>
[akpm: this is a previously-nacked patch, but the problem is real]
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure the driver's module owner field is
initialised for when this is being built and
loaded as a module.
Also change make the dm9000_tx_done function
static, as it is not exported elsewhere.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DM9000 initialisation sequence for the
hardware re-initialise the board spin-lock,
which is in my view wrong.
This patch removes the extra spin lock
initialisation
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DM9000 driver does not deal with the case
where there is no serial EEPROM to store the
configuration, and the bootloader has placed
an MAC address into the device already.
If there is no valid MAC in the EEPROM, read
the one already in the chip and check to see
if that one is valid.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current DM9000 driver cannot cope if it
is given more than 3 resources (for example, if
it is being passed an wake-up irq that it is
not using yet).
Check that we have been given at-least one IRQ
resource.
Also fix the minor type-casting for the case
of 2 resources.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ata_piix's Kconfig entry still refers only to ICH5, while it supports ICH6
through 8. This creates confusion with people who are looking to see
if their newer SATA enabled motherboards are supported. The
following patch makes this clear.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SATA controllers embedded in ATI IXPs seem to have broken
SATA_IRQ bit in their bmdma2 registers which is always stuck at 1.
This makes the driver believe that there has been a hotplug event and
freeze the port whenever there's an interrupt thus failing all
commands.
This patch disables SATA_IRQ for those controllers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cosmetic updates in libata-core.c.
* trim trailing whitespaces
* break lines which are over 80 column
* kill unnecessary braces
* make indentation consistent
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Andrew Morton <akpm@osdl.org>
Provide a module parameter to override the default 30-second-per-device SATA
probing timeout.
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_do_simple_cmd() and ata_flush_cache() global. These will be
used from libata-eh.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* the function has always returned AC_ERR_* masks not -errno but its
return type was int. Make return type unsigned int.
* don't print error message automatically. it's the caller's
responsibility.
* add header comment
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clear related EH action on device detach such that new device doesn't
receive EH actions scheduled for the old one.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement and use ata_eh_dev_action() which returns EH action mask for
a device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Partially revert 74d0a988d3:
[PATCH] PCI: Move various PCI IDs to header file
libata policy is to avoid use of named PCI device ID constants.
These are often single-use constants, which have little value over
direct numeric constants save for constant include/linux/pci_ids.h
patching/merging headaches.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- DMA CSR register is cleared by reading on omap1, but on
omap2 it is cleard by writing to it.
- DMA TOUT interrupt does not exist on omap24xx, rename it
- Add SECURE and MISALIGNED errors by default for omap24xx
- Add defines for external DMA request lines
Signed-off-by: Tony Lindgren <tony@atomide.com>
This may seem like a DILLIGAF, but after chatting with the F/W folks,
there is no harm in dropping the page calculation as denoted in the
enclosed patch for these older adapters in this new age of 4GB+ memory
sticks. Any resource optimization within the old-old-old adapters for
systems with less than 4G of memory is of little consequence. The
existing AAC_QUIRK_31BIT flag in linit.c should look after the rest of
the legacy hardware DMA limitations.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The scsi layer is already calling add_disk_randomness in scsi_end_request.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We currently stuff a truncated size into the geometry logic and return the
result which can produce bizarre reports for a 4Tb array. Since that
mapping logic isn't useful for disks that big don't try and map this way at
all.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix sparse warnings: use NULL instead of 0 for pointers:
drivers/scsi/lpfc/lpfc_els.c:827:56: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2781:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2782:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:951:21: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:956:20: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code incorrectly assigned it to the driver's
link-down-timeout value (a value in seconds).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also remove qla2xxx_probe_one/qla2xxx_remove_one stubs previously
used with external firmware module loaders.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As there is no point in failing the initialization process when
firmware informs the host software that it could not transition
beyond a CONFIG_WAIT nor WAIT_FOR_LOGIN state. Previous logic
would mark such conditions as a general *failure* and subsequently
tear-down the scsi-host during initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similar in form to QLogic's standard offering -- via
the 'extended_error_logging' module parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- macro usage statements should terminate with a ';'
- remove unused macros.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The host section of ISP24xx NVRAMs contain a new bit which
allows a user to selectively disable ports of an HBA. These
ports (hosts) will not be presented to the midlayer.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Defer firmware dump-data raw-to-textual conversion to
user-space.
- Add module parameter (ql2xallocfwdump) to allow for per-HBA
allocations of firmware dump memory.
- Dump request and response queue data as per firmware group
request.
- Add extended firmware trace support for ISP24XX/ISP54XX chips.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Bellon found a bug in my tlclk driver. Thanks!
I botch the register mask for store_received_ref_clk3a.
See http://download.intel.com/design/network/manuals/30412001.pdf
tables 124 and 136 for details.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
The changes in the tty handling contain a bug while accessing
the last byte in the skb. Since special sequence for control of
DTMF and FAX via ttyI* devices handled via this path, these services
do not work anymore.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've always found this flag confusing. Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.
Also fixes all drivers that use this flag.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was spotted by coverity #id 1300. Since the array has only four
elements, we should just use those four.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit c7b2eff059.
Hugh Dickins explains:
"It seems too little tested: "losetup -d /dev/loop0" fails with
EINVAL because nothing sets lo_thread; but even when you patch
loop_thread() to set lo->lo_thread = current, it can't survive
more than a few dozen iterations of the loop below (with a tmpfs
mounted on /tst):
j=0
cp /dev/zero /tst
while :
do
let j=j+1
echo "Doing pass $j"
losetup /dev/loop0 /tst/zero
mkfs -t ext2 -b 1024 /dev/loop0 >/dev/null 2>&1
mount -t ext2 /dev/loop0 /mnt
umount /mnt
losetup -d /dev/loop0
done
it collapses with failed ioctl then BUG_ON(!bio).
I think the original lo_done completion was more subtle and safe
than the kthread conversion has allowed for."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: trivial fixes in Makefile
kbuild: adding symbols in Kconfig and defconfig to TAGS
kbuild: replace abort() with exit(1)
kbuild: support for %.symtypes files
kbuild: fix silentoldconfig recursion
kbuild: add option for stripping modules while installing them
kbuild: kill some false positives from modpost
kbuild: export-symbol usage report generator
kbuild: fix make -rR breakage
kbuild: append -dirty for updated but uncommited changes
kbuild: append git revision for all untagged commits
kbuild: fix module.symvers parsing in modpost
kbuild: ignore make's built-in rules & variables
kbuild: bugfix with initramfs
kbuild: modpost build fix
kbuild: check license compatibility when building modules
kbuild: export-type enhancement to modpost.c
kbuild: add dependency on kernel.release to the package targets
kbuild: `make kernelrelease' speedup
kconfig: KCONFIG_OVERWRITECONFIG
...
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4227): Update this driver for recent header file movement.
V4L/DVB (4223): Add V4L2_CID_MPEG_STREAM_VBI_FMT control
V4L/DVB (4222): Always switch tuner mode when calling VIDIOC_S_FREQUENCY.
V4L/DVB (4221): Add HM12 YUV format define.
V4L/DVB (4219): Av7110: analog sound output of DVB-C rev 2.3
V4L/DVB (4217): Fix a misplaced closing bracket/else, which caused swzigzag not to be called
V4L/DVB (4215): Make VIDEO_CX88_BLACKBIRD a separate build option
V4L/DVB (4214): Make VIDEO_CX2341X a selectable build option
V4L/DVB (4213): Cx88: cleanups
V4L/DVB (4211): Fix an Oops for all fe that have get_frontend_algo == NULL
CC drivers/pci/msi-apic.o
In file included from include/asm/msi.h:11,
from drivers/pci/msi.h:71,
from drivers/pci/msi-apic.c:8:
include/asm/smp.h:103: error: syntax error before '->' token
akpm: nasty. It appears to be
static inline unsigned int cpu_mask_to_apicid(cpumask_t cpumask)
conflicting with include/asm-x86_64/mach_apic.h's
#define cpu_mask_to_apicid (genapic->cpu_mask_to_apicid)
And I don't know which patch in rc4-mm1 triggered this.
Fixing this in the .c file seems wrong.
Including asm/smp.h instead of linux/smp.h seems wrong too. Need that
.config.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During some profiling I noticed that default_idle causes a lot of
memory traffic. I think that is caused by the atomic operations
to clear/set the polling flag in thread_info. There is actually
no reason to make this atomic - only the idle thread does it
to itself, other CPUs only read it. So I moved it into ti->status.
Converted i386/x86-64/ia64 for now because that was the easiest
way to fix ACPI which also manipulates these flags in its idle
function.
Cc: Nick Piggin <npiggin@novell.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Rename the GART_IOMMU option to IOMMU to make clear it's not
just for AMD
- Rewrite the help text to better emphatise this fact
- Make it an embedded option because too many people get it wrong.
To my astonishment I discovered the aacraid driver tests this
symbol directly. This looks quite broken to me - it's an internal
implementation detail of the PCI DMA API. Can the maintainer
please clarify what this test was intended to do?
Cc: linux-scsi@vger.kernel.org
Cc: alan@redhat.com
Cc: markh@osdl.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Factor out the duplicated access/cache code into a single file
* Shared between i386/x86-64.
- Share flush code between AGP and IOMMU
* Fix a bug: AGP didn't wait for end of flush before
- Drop 8 northbridges limit and allocate dynamically
- Add lock to serialize AGP and IOMMU GART flushes
- Add PCI ID for next AMD northbridge
- Random related cleanups
The old K8 NUMA discovery code is unchanged. New systems
should all use SRAT for this.
Cc: "Navin Boppuri" <navin.boppuri@newisys.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC]: Add iomap interfaces.
[OPENPROM]: Rewrite driver to use in-kernel device tree.
[OPENPROMFS]: Rewrite using in-kernel device tree and seq_file.
[SPARC]: Add unique device_node IDs and a ".node" property.
[SPARC]: Add of_set_property() interface.
[SPARC64]: Export auxio_register to modules.
[SPARC64]: Add missing interfaces to dma-mapping.h
[SPARC64]: Export _PAGE_IE to modules.
[SPARC64]: Allow floppy driver to build modular.
[SPARC]: Export x_bus_type to modules.
[RIOWATCHDOG]: Fix the build.
[CPWATCHDOG]: Fix the build.
[PARPORT] sunbpp: Fix typo.
[MTD] sun_uflash: Port to new EBUS device layer.
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
[IOAT]: Do not dereference THIS_MODULE directly to set unsafe.
[NETROM]: Fix possible null pointer dereference.
[NET] netpoll: break recursive loop in netpoll rx path
[NET] netpoll: don't spin forever sending to stopped queues
[IRDA]: add some IBM think pads
[ATM]: atm/mpc.c warning fix
[NET]: skb_find_text ignores to argument
[NET]: make net/core/dev.c:netdev_nit static
[NET]: Fix GSO problems in dev_hard_start_xmit()
[NET]: Fix CHECKSUM_HW GSO problems.
[TIPC]: Fix incorrect correction to discovery timer frequency computation.
[TIPC]: Get rid of dynamically allocated arrays in broadcast code.
[TIPC]: Fixed link switchover bugs
[TIPC]: Enhanced & cleaned up system messages; fixed 2 obscure memory leaks.
[TIPC]: First phase of assert() cleanup
[TIPC]: Disallow config operations that aren't supported in certain modes.
[TIPC]: Fixed memory leak in tipc_link_send() when destination is unreachable
[TIPC]: Added missing warning for out-of-memory condition
[TIPC]: Withdrawing all names from nameless port now returns success, not error
[TIPC]: Optimized argument validation done by connect().
...
Usually we don't care much about 'gcc -W' warnings, but some of us do build
kernels that way to look for problems, and then the fewer warnings we have
to wade through the better. Especially when they are very easy and
non-intrusive to clean up. Which is the case for the following warnings
spewed by drivers/usb/storage/usb.h :
drivers/usb/storage/usb.h:163: warning: `inline' is not at beginning of
+declaration
drivers/usb/storage/usb.h:166: warning: `inline' is not at beginning of
+declaration
There's also some precedence for cleaning up these warnings. I've had
a few patches merged in the past that remove exactly this class of
warnings.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Make needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It appears in /sys/mdX/md/dev-YYY/state
and can be set or cleared by writing 'writemostly' or '-writemostly'
respectively.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The md/dev-XXX/state file can now be written:
"faulty" simulates an error on the device
"remove" removes the device from the array (if it is not busy)
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows the state of an md/array to be directly controlled via sysfs and
adds the ability to stop and array without tearing it down.
Array states/settings:
clear
No devices, no size, no level
Equivalent to STOP_ARRAY ioctl
inactive
May have some settings, but array is not active
all IO results in error
When written, doesn't tear down array, but just stops it
suspended (not supported yet)
All IO requests will block. The array can be reconfigured.
Writing this, if accepted, will block until array is quiescent
readonly
no resync can happen. no superblocks get written.
write requests fail
read-auto
like readonly, but behaves like 'clean' on a write request.
clean - no pending writes, but otherwise active.
When written to inactive array, starts without resync
If a write request arrives then
if metadata is known, mark 'dirty' and switch to 'active'.
if not known, block and switch to write-pending
If written to an active array that has pending writes, then fails.
active
fully active: IO and resync can be happening.
When written to inactive array, starts with resync
write-pending (not supported yet)
clean, but writes are blocked waiting for 'active' to be written.
active-idle
like active, but no writes have been seen for a while (100msec).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- record the 'event' count on each individual device (they
might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
block only needs to be updated to record a clean<->dirty
transition.
- Prefer odd event numbers for dirty states and even numbers
for clean states
- Using all the above, don't update the superblock on
a spare device if the update is just doing a clean-dirty
transition. To accomodate this, a transition from
dirty back to clean might now decrement the events counter
if nothing else has changed.
The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array has a bitmap, a device can be removed and re-added and only
blocks changes since the removal (as recorded in the bitmap) will be resynced.
It should be possible to do a similar thing to arrays without bitmaps. i.e.
if a device is removed and re-added and *no* changes have been made in the
interim, then the add should not require a resync.
This patch allows that option. This means that when assembling an array one
device at a time (e.g. during device discovery) the array can be enabled
read-only as soon as enough devices are available, but extra devices can still
be added without causing a resync.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As data_disks is *less* than raid_disks, the current test here is obviously
wrong. And as the difference is already available in conf->max_degraded, it
makes much more sense to use that.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RAID5 recently changed to RAID456
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was experimenting with Linux SW raid today and found a spelling error when
reading the help menus... (and fly spell found more).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The size calculation made assumtion which the new offset mode didn't
follow. This gets the size right in all cases.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix problems with new bmap based access to bitmap files.
1/ When not using a file based bitmap, attach a NULL list of buffers
to each page so the common free_buffer routine can cope.
2/ Use submit_bh to read as well as write, rather than vfs_read.
This makes read and write more symetric.
3/ sync the file before reading, to ensure that the page cache has no
dirty pages that might get written out later.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If md is asked to store a bitmap in a file, it tries to hold onto the page
cache pages for that file, manipulate them directly, and call a cocktail of
operations to write the file out. I don't believe this is a supportable
approach.
This patch changes the approach to use the same approach as swap files. i.e.
bmap is used to enumerate all the block address of parts of the file and we
write directly to those blocks of the device.
swapfile only uses parts of the file that provide a full pages at contiguous
addresses. We don't have that luxury so we have to cope with pages that are
non-contiguous in storage. To handle this we attach buffers to each page, and
store the addresses in those buffers.
With this approach the pagecache may contain data which is inconsistent with
what is on disk. To alleviate the problems this can cause, md invalidates the
pagecache when releasing the file. If the file is to be examined while the
array is active (a non-critical but occasionally useful function), O_DIRECT io
must be used. And new version of mdadm will have support for this.
This approach simplifies a lot of code:
- we no longer need to keep a list of pages which we need to wait for,
as the b_endio function can keep track of how many outstanding
writes there are. This saves a mempool.
- -EAGAIN returns from write_page are no longer possible (not sure if
they ever were actually).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap modifies i_writecount of a bitmap file to make sure that no-one else
writes to it. The reverting of the change is sometimes done twice, and there
is one error path where it is omitted.
This patch tidies that up.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bitmap_active is never called, and the BITMAP_ACTIVE flag is never users or
tested, so discard them both.
Also remove some out-of-date 'todo' comments.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap gets a collection of pages representing the bitmap when it
initialises the bitmap, and puts all the references when discarding the
bitmap.
It also occasionally takes extra references without any good reason, and
sometimes drops them ... though it doesn't always drop them, which can result
in a memory leak.
This patch removes the unnecessary 'get_page' calls, and the corresponding
'put_page' calls.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In particular, this means that we use 4 bits per page instead of a whole
unsigned long.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap has some attributes per-page. Handling of these attributes in
largely abstracted in set_page_attr and clear_page_attr. However
get_page_attr exposes the format used to store them. So prior to changing
that format, introduce test_page_attr instead of get_page_attr, and make
appropriate usage changes.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap currently has a separate thread to wait for writes to the bitmap
file to complete (as we cannot get a callback on that action).
However this isn't needed as bitmap_unplug is called from process context and
waits for the writeback thread to do it's work. The same result can be
achieved by doing the waiting directly in bitmap_unplug.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When "mdadm --grow /dev/mdX --bitmap=none" is used to remove a filebacked
bitmap, the bitmap was disconnected from the array, but the file wasn't closed
(until the array was stopped).
The file also wasn't closed if adding the bitmap file failed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... as raid5 sync_request is WAY too big.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the needlessly global md_print_devices() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The "industry standard" DDF format allows for a stripe/offset layout where
data is duplicated on different stripes. e.g.
A B C D
D A B C
E F G H
H E F G
(columns are drives, rows are stripes, LETTERS are chunks of data).
This is similar to raid10's 'far' mode, but not quite the same. So enhance
'far' mode with a 'far/offset' option which follows the layout of DDFs
stripe/offset.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For a while we have had checkpointing of resync. The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.
Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At shutdown, we switch all arrays to read-only, which creates a message for
every instantiated array, even those which aren't actually active.
So remove the message for non-active arrays.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a lot of commonality between raid5.c and raid6main.c. This patches
merges both into one module called raid456. This saves a lot of code, and
paves the way for online raid5->raid6 migrations.
There is still duplication, e.g. between handle_stripe5 and handle_stripe6.
This will probably be cleaned up later.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a md array has been idle (no writes) for 20msecs it is marked as 'clean'.
This delay turns out to be too short for some real workloads. So increase it
to 200msec (the time to update the metadata should be a tiny fraction of that)
and make it sysfs-configurable.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This warning was slightly useful back in 2.2 days, but is more an annoyance
now. It makes it awkward to add new ioctls (that we we are likely to do that
in the current climate, but it is possible).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The largest chunk size the code can support without substantial surgery is
2^30 bytes, so make that the limit instead of an arbitrary 4Meg. Some day,
the 'chunksize' should change to a sector-shift instead of a byte-count. Then
no limit would be needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent change made this goto unnecessary, so reformat the code to make it
clearer what is happening.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tidy device-mapper error messages to include context information
automatically.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If you misuse the device-mapper interface (or there's a bug in your userspace
tools) it's possible to end up with 'unlinked' mapped devices that cannot be
removed until you reboot (along with uninterruptible processes).
This patch prevents you from removing a device that is still open.
It introduces dm_lock_for_deletion() which is called when a device is about to
be removed to ensure that nothing has it open and nothing further can open it.
It uses a private open_count for this which also lets us remove one of the
problematic bdget_disk() calls elsewhere.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a library function dm_create_error_table() to create a table that rejects
any I/O sent to a device with EIO.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move definitions of core device-mapper functions for manipulating mapped
devices and their tables to <linux/device-mapper.h> advertising their
availability for use elsewhere in the kernel.
Protect the contents of device-mapper.h with ifdef __KERNEL__. And throw
in a few formatting clean-ups and extra comments.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merge dm_create() and dm_create_with_minor() by introducing the special value
DM_ANY_MINOR to request the allocation of the next available minor number.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Return sense if dm_split_args is called with a NULL input parameter.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kcopyd should accumulate errors - otherwise I/O failures may be ignored
unintentionally.
And invert 'success' (used in a future patch), using a more intuitive
!(read_err || write_err).
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a mirror is reduced in size, clear the part of the bitmap that is no
longer used.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the 'sizeof' in the region log bitmap size calculation: it's uint32_t, not
unsigned long - this breaks on some archs.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Refactor the code that creates the core and disk log contexts to avoid the
repeated allocation of clean_bits introduced by the last patch.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On-disk logs for dm-mirror devices are currently hard-coded to use 512 byte
hard-sector-sizes. This patch fixes dm-log so it will work with devices with
non-512-byte hard-sector-sizes.
To maintain full compatibility, instead of moving the clean-bits bitset to a
bitset, and enlarges the disk-header buffer to encompass both the header and
the bitset. The I/O routines for the bitset are removed, and the I/O routines
for the disk-header now also read/write the bitset.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The table is indexed from 0, so an index equal to t->num_targets should be
rejected.
(There is no code in the current tree that would exercise this bug.)
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The device-mapper core does not perform any remapping of bios before passing
them to the targets. If a particular mapping begins part-way into a device,
targets obtain the sector relative to the start of the mapping by subtracting
ti->begin.
The dm-raid1 target didn't do this everywhere: this patch fixes it, taking
care to subtract ti->begin exactly once for each bio.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In alloc_dev(), we register the device with the block layer and then continue
to initialize the device. But register_disk() makes the device available to
be opened before we have completed initialising it.
This patch moves the final bits of the initialization above the disk
registration.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The reference counting on dm-mod is zero if no mapped devices are open. This
is incorrect, and can lead to an oops if the module is unloaded while mapped
devices exist.
This patch claims a reference to the module whenever a device is created, and
drops it again when the device is freed.
Devices must be removed before dm-mod is unloaded.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To avoid races, _minor_lock must be held while changing mapped device
reference counts.
There are a few paths where a mapped_device pointer is returned before a
reference is taken. This patch fixes them.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a chicken and egg problem between the block layer and dm in which the
gendisk associated with a mapping keeps a reference-less pointer to the
mapped_device.
This patch uses a new flag DMF_FREEING to indicate when the mapped_device is
no longer valid. This is checked to prevent any attempt to open the device
from succeeding while the device is being destroyed.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While removing a device, another another thread might attempt to resurrect it.
This patch replaces the _minor_lock mutex with a spinlock and uses
atomic_dec_and_lock() to serialize reference counting in dm_put().
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
idr_pre_get() can sleep while allocating memory.
The next patch will change _minor_lock into a spinlock, so this patch moves
idr_pre_get() outside the lock in preparation.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One part of the system can attempt to use a mapped device before another has
finished initialising it or while it is being freed.
This patch introduces a place holder value, MINOR_ALLOCED, to mark the minor
as allocated but in a state where it can't be used, such as mid-allocation or
mid-free. At the end of the initialization, it replaces the place holder with
the pointer to the mapped_device, making it available to the rest of the dm
subsystem.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Persistent snapshots currently store a private copy of the chunk size.
Userspace also supplies the chunk size when loading a snapshot. Ensure
consistency by only storing the chunk_size in one place instead of two.
Currently the two sizes will differ if the chunk size supplied by userspace
does not match the chunk size an existing snapshot actually uses. Amongst
other problems, this causes an incorrect 'percentage full' to be reported.
The patch ensures consistency by only storing the chunk_size in one place,
removing it from struct pstore. Some initialisation is delayed until the
correct chunk_size is known. If read_header() discovers that the wrong chunk
size was supplied, the 'area' buffer (which the header already got read into)
is reinitialised to the correct size.
[akpm: too late for 2.6.17 - suitable for 2.6.17.x after it has settled]
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not mark sticon_startup() as __init
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not mark promcon_startup() and promcon_init_unimap() as __init
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- move register ioremap from newport_startup() to newport_console_init()
- fonts are freed multiple times, do it only once
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not mark mdacon_startup __init.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The class device "fbcon" does not need to be a device file. Do not create one
by passing a major and minor number of zero to
class_device_create()/destroy().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To enable this feature, CONFIG_VT_HW_CONSOLE_BINDING must be set to 'y'. This
feature will default to 'n' to minimize users accidentally corrupting their
virtual terminals.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add sysfs control to the VT layer. A new sysfs class, 'vtconsole', and class
devices 'vtcon[n]' are added. Each class device file has the following
attributes:
/sys/class/vtconsole/vtcon[n]/name - read-only attribute showing the
name of the current backend
/sys/class/vtconsole/vtcon[n]/bind - read/write attribute
where: 0 - backend is unbound/unbind backend from the VT layer
1 - backend is bound/bind backend to the VT layer
In addition, if any of the consoles are in KD_GRAPHICS mode, binding and
unbinding will not succeed. KD_GRAPHICS mode usually indicates that the
underlying console hardware is used for other purposes other than displaying
text (ie X). This feature should prevent binding/unbinding from interfering
with a graphics application using the VT.
[akpm@osdl.org: warning fixes]
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The control for binding/unbinding is moved from fbcon to the console layer.
Thus the fbcon sysfs attributes, attach and detach, are also gone.
1. Add a notifier event that tells fbcon if a framebuffer driver has been
unregistered. If no registered driver remains, fbcon will unregister
itself from the console layer.
2. Replaced calls to give_up_console() with unregister_con_driver().
3. Still use take_over_console() instead of register_con_driver() to
maintain compatibility
4. Respect the parameter first_fb_vc and last_fb_vc instead of using 0 and
MAX_NR_CONSOLES - 1. These parameters are settable by the user.
5. When fbcon is completely unbound from the console layer, fbcon will
also release (iow, decrement module reference counts to zero) all fbdev
drivers. In other words, a bind or unbind request from the console layer
will propagate down to the framebuffer drivers.
6. If fbcon is not bound to the console, it will ignore all notifier
events (except driver registration and unregistration) and all sysfs
requests.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The framebuffer console is now able to dynamically bind and unbind from the VT
console layer. Due to the way the VT console layer works, the drivers
themselves decide when to bind or unbind. However, it was decided that
binding must be controlled, not by the drivers themselves, but by the VT
console layer. With this, dynamic binding is possible for all VT console
drivers, not just fbcon.
Thus, the VT console layer will impose the following to all VT console
drivers:
- all registered VT console drivers will be entered in a private list
- drivers can register themselves to the VT console layer, but they cannot
decide when to bind or unbind. (Exception: To maintain backwards
compatibility, take_over_console() will automatically bind the driver after
registration.)
- drivers can remove themselves from the list by unregistering from the VT
console layer. A prerequisite for unregistration is that the driver must not
be bound.
The following functions are new in the vt.c:
register_con_driver() - public function, this function adds the VT console
driver to an internal list maintained by the VT console
bind_con_driver() - private function, it binds the driver to the console
take_over_console() is changed to call register_con_driver() followed by a
bind_con_driver(). This is the only time drivers can decide when to bind to
the VT layer. This is to maintain backwards compatibility.
unbind_con_driver() - private function, it unbinds the driver from its
console. The vacated consoles will be taken over by the default boot console
driver.
unregister_con_driver() - public function, removes the driver from the
internal list maintained by the VT console. It will only succeed if the
driver is currently unbound.
con_is_bound() checks if the driver is currently bound or not
give_up_console() is just a wrapper to unregister_con_driver().
There are also 3 additional functions meant to be called only by the tty layer
for sysfs control:
vt_bind() - calls bind_con_driver()
vt_unbind() - calls unbind_con_driver()
vt_show_drivers() - shows the list of registered drivers
Most VT console drivers will continue to work as is, but might have problems
when unbinding or binding which should be fixable with minimal changes.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the ability to detach and attach the framebuffer console to and from the
vt layer. This is done by echo'ing any value to sysfs attributes located in
class/graphics/fbcon. The two attributes are:
attach - bind fbcon to the vt layer
detach - unbind fbcon from the vt layer
Once fbcon is detached from the vt layer, fbcon can be unloaded if compiled as
a module. This feature is quite useful for developers who work on the
framebuffer or console subsystem. This is also useful for users who want to
go to text mode or graphics mode without having to reboot.
Directly unloading the fbcon module is not possible because the vt layer
increments the module reference count for all bound consoles. Detaching fbcon
decrements the module reference count to zero so unloading becomes possible.
Detaching fbcon may interfere with X and/or DRM.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To detach fbcon, it must also clean up all resources it allocated. This was
never done before because fbcon cannot be unloaded.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order for this feature to work, an interface will be needed. The most
appropriate is sysfs. However, the framebuffer console has no sysfs entry
yet. This will create a sysfs class device entry for fbcon under
/sys/class/graphics.
Add a class_device entry 'fbcon' under class 'graphics'. Console-specific
attributes which where previously under class/graphics/fb[x] are moved to
class/graphics/fbcon. These attributes, 'con_rotate' and 'con_rotate_all',
are also renamed to 'rotate' and 'rotate_all' respectively.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Detaching fbcon allows individual drivers to be unloaded. However several
drivers call pci_disable_device() upon exit. This function will disable the
BAR's which will kill VGA text mode and/or affect X/DRM.
To prevent this, remove calls to pci_disable_device() from several drivers.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To allow for detaching fbcon, it must be able to give up the console.
However, the function give_up_console() is plain broken. It just sets the
entries in the console driver map to NULL, it leaves the vt layer without a
console driver, and does not decrement the module reference count. Calling
give_up_console() is guaranteed to hang the machine..
To fix this problem, ensure that the virtual consoles are not left dangling
without a driver. All systems have a default boot driver (either vgacon or
dummycon) which is never unloaded. For those vt's that lost their driver, the
default boot driver is reassigned back to them.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of the limitations of the framebuffer console system is its inablity to
unload or detach itself from the console layer. And once it loads, it also
locks in framebuffer drivers preventing their unload. Although the con2fbmap
utility does provide a means to unload individual drivers, it requires that at
least one framebuffer driver is loaded for use by fbcon.
With this change, it is possible to detach fbcon from the console layer. If it
is detached, it will reattach the boot console driver (which is permanently
loaded) back to the console layer so the system can continue to work. As a
consequence, fbcon will also decrement its reference count of individual
framebuffer drivers, allowing all of these drivers to be unloaded even if
fbcon is still loaded.
Unless you use drivers that restores the display to text mode (rivafb and
i810fb, for example), detaching fbcon does require assistance from userspace
tools (ie, vbetools) for text mode to be restored completely. Without the
help of these tools, fbcon will leave the VGA console corrupted. The methods
that can be used will be described in Documentation/fb/fbcon.txt.
Because the vt layer also increments the module reference count for each
console driver, fbcon cannot be directly unloaded. It must be detached first
prior to unload.
Similarly, fbcon can be reattached to the console layer without having to
reload the module. A nice feature if fbcon is compiled statically.
Attaching and detaching fbcon is done via sysfs attributes. A class device
entry for fbcon is created in /sys/class/graphics. The two attributes that
controls this feature are detach and attach. Two other attributes that are
piggybacked under /sys/class/graphics/fb[n] that are fbcon-specific,
'con_rotate' and 'con_rotate_all' are moved to fbcon. They are renamed as
'rotate' and 'rotate_all' respectively.
Overall, this feature is a great help for developers working in the
framebuffer or console layer. There is not need to continually reboot the
kernel for every small change. It is also useful for regular users who wants
to choose between a graphical console or a text console without having to
reboot.
Example usage for x86:
/* start in text mode */
modprobe xxxfb
modprobe fbcon
/* graphical mode with fbcon using xxxfb */
echo 1 > /sys/class/graphics/fbcon/detach
/* back to text mode, will produce corrupt display unless vbetool is used */
rmmod xxxfb
modprobe yyyfb
/* back to graphical mode with fbcon using yyyfb */
Before trying out this feature, please read Documentation/fb/fbcon.txt.
This patch:
In order for fbcon to detach itself from the console layer, vgacon, which is a
boot console driver, must be fixed so it can retake the console multiple
times, not just during init. The following needs to be done:
- remove __init from the vgacon_startup, this is called again by
take_over_console().
- vc->rows and vc->cols are set manually by vgacon during init. After init,
vc_resize() can be used
- make sure the scrollback_buffer is not reallocated
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the sysfs description of a video mode such that modes are tagged with
their scan type, (p)rogessive, (i)nterlaced, (d)ouble scan. For example,
U:1920x1080i-50. This is useful to disambiguate some of the 'consumer' video
timings found in CEA-861 (especially those for EDTV).
Signed-off-by: Daniel R Thompson <daniel.thompson@st.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new framebuffer driver for the Intel Based macs. This
framebuffer is needed when booting from EFI to get something out the box.
[akpm: note: doesn't support modular building]
[akpm@osdl.org: cleanups]
Signed-off-by: Edgar Hucek <hostmaster@ed-soft.at>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the following warning:
WARNING: drivers/video/aty/atyfb.o - Section mismatch: reference to
.init.text:aty_init_cursor from .text between 'aty_init' (at offset 0x241d)
and 'atyfb_blank'
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Logo drawing crashes or produces a corrupt display if the logo width and
height are not equal. The dimensions are transposed prior to the actual
rotation and the width is used instead of the height in the actual rotation
code. These produce a corrupt image.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a fix for the most annoying problem that remained with neofb:
After "setterm -powersave powerdown" the console blanker will disable the
backlight after the given timeout expires. If this happens after the lid
has been shut, we read "LCD off" from the register and store that in the
driver. Once the lid is opened, the backlight turns on, but any key press
that would awaken the blanked console will switch the backlight off again.
The workaround so far was to use the "display config toggle" Fn key combo -
once if no external display is attached, otherwise as often as required to
restore the desired display setup.
The following patch fixes the issue at least for the LCD-only case, with no
external monitor attached. Other display setup permutations are pending
further testing, but so far I can guarantee at least no negative change in
behaviour, if any at all.
Signed-off-by: Christian Trefzer <ctrefzer@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_FB = m and CONFIG_{BACKLIGHT:LCD}_CLASS_DEVICE = y is possible
resulting in link errors. Fix by making backlight and lcd class also depend
on FB
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
regs.lcdcon1 was not updated on suspend. The result was a garbaged display on
resume. This bug was first noticed by Christer Weinigel. This patch is a
modified version of the one he sent to me.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delay the update of the visible framebuffer console until all other consoles
have been initialized in order to avoid losing information. This only seems
to be a problem with modules, not with built-in drivers.
Signed-off-by: David Hollister <david.hollister@amd.com>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- As per VESA specs, use the VGA registers to set the palette if the mode is
VGA compatible. Otherwise, use the protected mode interface.
- Make pmi_setpal default to 1
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the hardware palette cannot be accessed, make vesafb_setcolreg return a
nonzero value.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for Geforce 6100 and related chipsets (PCI device id 0x024x)
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- make firmware edid independent from framebuffer (No need to choose
framebuffer just to disable this option
- enable this option in X86_64
- check if VBE/DDC function is implemented before calling actual function
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A static pseudocolor visual with depth less than 4 does exist, so let's not
accidentally upscale the depth with this configuration
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set the appropriate acceleration flags so fbcon can choose the optimal
scrolling mode.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The drawing functions of atyfb is unecessary syncing the GPU which is
affecting performance. Remove the calls, any direct access by fbcon to the
framebuffer will always be preceeded by a call to atyfb_sync().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix image and color handling in atyfb_cursor()
- In the 2-bit scheme of the cursor image, just set the first bit to be
always zero (turn off transparency and/or XOR), and just do the masking
manually
- The cursor color is converted into 32-bit RGBA8888 using struct fb_cmap.
Each component in the cmap is u16 in size, so mask the upper 8 bits.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nVidia is churning out chipsets like there's no tomorrow. And even though the
pci_device_id table now has numerous entries, it is still not guaranteed that
all supported devices are included or will be included.
Fortunately, nvidiafb has chipset detection logic built in. So, change the
contents of the pci_device_id table so it will capture all nVidia devices of
the display class. Unsupported chipsets will then be filtered out by
nvidiafb's detection logic.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The EDID block should specify the display's operating limits (vertical and
horizontal sync ranges, and maximum dot clock). If not given by the EDID
block, the ranges are extrapolated from the modelist. However, the
computation used is only a rough approximation, and the resulting values may
not reflect the actual capability of the display. This problem is frequently
encountered when the EDID block has a single entry, the single mode entry will
fail validation.
To prevent this, calculate the values based on the same method used in
fb_validate_mode().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove unneeded duplicate #include's of the same header file.
In the case of fbmon.c linux/pci.h is now #include'd unconditional, but
this should be safe.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We had three (sic) VIDEO_SELECT options:
- two in drivers/video/Kconfig
- one in drivers/video/console/Kconfig
This patch removes the two options in drivers/video/Kconfig and also removes
the unneeded usage in drivers/video/sis/sis_main.c .
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add backlight intensity control to the LOCOMO lcd/backlight driver using the
backlight class and add basic power management support.
This is a reimplementation and improvement of patches by John Lenz and Pavel
Machek
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Rich (Bugzilla Bug 6417)
"if savage driver is used in x.org together with savagefb, it results in
seriously garbled and distorted screen - coupled with severe slowdowns."
This bug is the result of Xorg unable to handle savagefb altering the
hardware which results in X failing to start properly and/or failed console
switching.
Add savagefb_state_save and savagefb_state_restore. These hooks will only
save and restore the extended VGA registers. Standard VGA registers will be
left alone. This is enough to make savagefb play nicely with the latest
Xorg savage driver, and perhaps with savage DRI. (Transient screen artifacts
may appear before X loads and during console switches).
(Unfortunately, blanking the screen also leaves Xorg in a blanked state, so I
have to unblank the screen before Xorg loads. So I doubt if the transient
screen artifacts will be completely invisible but hopefully it will only be
for a shorter duration (not much).)
[akpm@osdl.org: cleanups]
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: <rich@hq.vsaa.lv>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allocate space for 2 register states: 'current' for the current state of
the hardware, and 'saved', to be used for restoring the hardware to a sane
state. This is in preparation for the addition of state save and restore
hooks to make savagefb work together with the latest Xorg savage driver.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver pdc202xx_old requires CONFIG_BLK_DEV_IDEDMA, so it's always
defined
Signed-off-by: Tobias Oed <tobiasoed@hotmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michal Piotrowski reported the following validator assert:
hdd: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdd: set_drive_speed_status: error=0xb4 { AbortedCommand LastFailedSense=0x0b }
============================
[ BUG: illegal lock usage! ]
----------------------------
illegal {in-hardirq-W} -> {hardirq-on-W} usage.
hdparm/1821 [HC0[0]:SC0[0]:HE1:SE1] takes:
(ide_lock){++..}, at: [<c0268388>] ide_dump_opcode+0x13/0x9b
[...]
stack backtrace:
[<c0104513>] show_trace+0x1b/0x20
[<c01045f1>] dump_stack+0x1f/0x24
[<c013976c>] print_usage_bug+0x1a5/0x1b1
[<c0139e90>] mark_lock+0x2ca/0x4f7
[<c013aa96>] __lockdep_acquire+0x47e/0xaa4
[<c013b536>] lockdep_acquire+0x67/0x7f
[<c030552d>] _spin_lock+0x24/0x32
[<c0268388>] ide_dump_opcode+0x13/0x9b
[<c02688b6>] ide_dump_status+0x4a6/0x4cc
[<c0267ae6>] ide_config_drive_speed+0x32a/0x33a
[<c0262dc5>] piix_tune_chipset+0x2ed/0x2f8
[<c0262e31>] piix_config_drive_xfer_rate+0x61/0xb5
[<c0263a82>] set_using_dma+0x2f/0x60
[<c0263bee>] ide_write_setting+0x4a/0xc3
[<c02647ca>] generic_ide_ioctl+0x8a/0x47f
[<f886003a>] idecd_ioctl+0xfd/0x133 [ide_cd]
[<c01f1fff>] blkdev_driver_ioctl+0x4b/0x5f
[<c01f2783>] blkdev_ioctl+0x770/0x7bd
[<c017dc0d>] block_ioctl+0x1f/0x21
[<c0189353>] do_ioctl+0x27/0x6e
[<c0189604>] vfs_ioctl+0x26a/0x280
[<c0189667>] sys_ioctl+0x4d/0x7e
[<c0305ed2>] sysenter_past_esp+0x63/0xa1
in ide_dump_opcode() takes the ide_lock in an irq-unsafe manner, i.e. this
function expects to be called with irqs disabled. But
ide_dump_ata[pi]_status() doesnt do that - it enables interrupts specifically.
That is a no-no - what guarantees that another IDE port couldnt generate an
IDE interrupt while we are dumping this error? The fix is to turn the
irq-enabling in these functions into irq-disabling.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the busproc from pdc202xx_old.c because:
- it handles the obsolete HDIO_TRISTATE_HWIF ioctl instead of the modern
HDIO_SET_BUSSTATE, so treats its argument wrong;
- I don't think that tristating both channels is good idea (probably can't
be done otherwise since there seems to be only single bit controlling this).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The function ide_timing_compute() fails to *actually* take drive's
specified minimum PIO/DMA cycle times into account -- when doing this, it
calls ide_timing_merge() on the 'struct ide_timing' argument which contains
garbage at the moment, and then ultimately destroys the read cycle time by
quantizing the ide_timing[] entry, instead of copying from that entry to
the argument structure, and only then doing a merge/quantize.
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During an STR resume cycle, the ide master disk times-out when there is
also a slave present (especially CD). Increasing the timeout in ide-io
from 10,000 to 100,000 fixes this problem.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This bit us a few kernels ago, and for some reason never made it's way
upstream.
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=144743
Kernel panic - not syncing: drivers/ide/pci/piix.c:231:
spin_lock(drivers/ide/ide.c:c03cef28) already locked by driver/ide/ide-iops.c/1153.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Dave Jones <davej@redhat.com>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove a call to hwif->tuneproc() on the error path of
config_chipset_for_dma(), as its single caller
(pdc202xx_config_drive_xfer_rate()) will do the call in that case.
Signed-off-by: Tobias Oed <tobiasoed@hotmail.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch to the common part of the Siemens Gigaset driver
prevents it from trying to send the +++ break sequence if the device has
been disconnected, and removes a couple of assignments which didn't have
any effect.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch to the Siemens Gigaset base driver adds graceful
recovery for some frequently encountered error conditions, by retrying
failed control requests (eg. stalled control pipe), and by closing and
reopening the AT command channel when it appears to be stuck.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes coverity bug #517.
Since IESIZE is greater than IESIZE_NI1 we might run past the end of
ielist_ni1. This fixes it by using the proper IESIZE_NI1 define.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I am getting more or less reproducible crashes from the CAPI subsystem
using the fcdsl driver:
Unable to handle kernel NULL pointer dereference at virtual address 00000010
printing eip:
c39bbca4
*pde = 00000000
Oops: 0000 [#1]
Modules linked in: netconsole capi capifs 3c59x mii fcdsl kernelcapi uhci_hcd usbcore ide_cd cdrom
CPU: 0
EIP: 0060:[<c39bbca4>] Tainted: P VLI
EFLAGS: 00010202 (2.6.16.11 #3)
EIP is at handle_minor_send+0x17a/0x241 [capi]
eax: c24abbc0 ebx: c0b4c980 ecx: 00000010 edx: 00000010
esi: c1679140 edi: c2783016 ebp: 0000c28d esp: c0327e24
ds: 007b es: 007b ss: 0068
Process swapper (pid: 0, threadinfo=c0326000 task=c02e1300)
Stack: <0>000005b4 c1679180 00000000 c28d0000 c1ce04e0 c2f69654 c221604e c1679140
c39bc19a 00000038 c20c0400 c075c560 c1f2f800 00000000 c01dc9b5 c1e96a40
c075c560 c2ed64c0 c1e96a40 c01dcd3b c2fb94e8 c075c560 c0327f00 c1e96a40
Call Trace:
[<c39bc19a>] capinc_tty_write+0xda/0xf3 [capi]
[<c01dc9b5>] ppp_sync_push+0x52/0xfe
[<c01dcd3b>] ppp_sync_send+0x1f5/0x204
[<c01d9bc1>] ppp_push+0x3e/0x9c
[<c01dacd4>] ppp_xmit_process+0x422/0x4cc
[<c01daf3f>] ppp_start_xmit+0x1c1/0x1f6
[<c0213ea5>] qdisc_restart+0xa7/0x135
[<c020b112>] dev_queue_xmit+0xba/0x19e
[<c0223f69>] ip_output+0x1eb/0x236
[<c0220907>] ip_forward+0x1c1/0x21a
[<c021fa6c>] ip_rcv+0x38e/0x3ea
[<c020b4c2>] netif_receive_skb+0x166/0x195
[<c020b55e>] process_backlog+0x6d/0xd2
[<c020a30f>] net_rx_action+0x6a/0xff
[<c0112909>] __do_softirq+0x35/0x7d
[<c0112973>] do_softirq+0x22/0x26
[<c0103a9d>] do_IRQ+0x1e/0x25
[<c010255a>] common_interrupt+0x1a/0x20
[<c01013c5>] default_idle+0x2b/0x53
[<c0101426>] cpu_idle+0x39/0x4e
[<c0328386>] start_kernel+0x20b/0x20d
Code: c0 e8 b3 b6 77 fc 85 c0 75 10 68 d8 c8 9b c3 e8 82 3d 75 fc 8b 43 60 5a eb 50 8d 56 50 c7 00 00 00 00 00 66 89 68 04 eb 02 89
ca <8b> 0a 85 c9 75 f8 89 02 89 da ff 46 54 8b 46 10 e8 30 79 fd ff
<0>Kernel panic - not syncing: Fatal exception in interrupt
That oops took me to the "ackqueue" implementation in capi.c. The crash
occured in capincci_add_ack() (auto-inlined by the compiler).
I read the code a bit and finally decided to replace the custom linked list
implementation (struct capiminor->ackqueue) by a struct list_head. That
did not solve the crash, but produced the following interresting oops:
Unable to handle kernel paging request at virtual address 00200200
printing eip:
c39bb1f5
*pde = 00000000
Oops: 0002 [#1]
Modules linked in: netconsole capi capifs 3c59x mii fcdsl kernelcapi uhci_hcd usbcore ide_cd cdrom
CPU: 0
EIP: 0060:[<c39bb1f5>] Tainted: P VLI
EFLAGS: 00010246 (2.6.16.11 #3)
EIP is at capiminor_del_ack+0x18/0x49 [capi]
eax: 00200200 ebx: c18d41a0 ecx: c1385620 edx: 00100100
esi: 0000d147 edi: 00001103 ebp: 0000d147 esp: c1093f3c
ds: 007b es: 007b ss: 0068
Process events/0 (pid: 3, threadinfo=c1092000 task=c1089030)
Stack: <0>c2a17580 c18d41a0 c39bbd16 00000038 c18d41e0 00000000 d147c640 c29e0b68
c29e0b90 00000212 c29e0b68 c39932b2 c29e0bb0 c10736a0 c0119ef0 c399326c
c10736a8 c10736a0 c10736b0 c0119f93 c011a06e 00000001 00000000 00000000
Call Trace:
[<c39bbd16>] handle_minor_send+0x1af/0x241 [capi]
[<c39932b2>] recv_handler+0x46/0x5f [kernelcapi]
[<c0119ef0>] run_workqueue+0x5e/0x8d
[<c399326c>] recv_handler+0x0/0x5f [kernelcapi]
[<c0119f93>] worker_thread+0x0/0x10b
[<c011a06e>] worker_thread+0xdb/0x10b
[<c010c998>] default_wake_function+0x0/0xc
[<c011c399>] kthread+0x90/0xbc
[<c011c309>] kthread+0x0/0xbc
[<c0100a65>] kernel_thread_helper+0x5/0xb
Code: 7e 02 89 ee 89 f0 5a f7 d0 c1 f8 1f 5b 21 f0 5e 5f 5d c3 56 53 8b 48 50 89 d6 89 c3 8b 11 eb 2f 66 39 71 08 75 25 8b 41 04 8b 11 <89> 10 89 42 04 c7 01 00 01 10 00 89 c8 c7 41 04 00 02 20 00 e8
The interresting part of it is the "virtual address 00200200", which is
LIST_POISON2. I thought about some race condition, but as this is an UP
system, it leads to questions on how it can happen. If we look at EFLAGS:
00010202, we see that interrupts are enabled at the time of the crash
(eflags & 0x200).
Finally, I don't understand all the capi code, but I think that
handle_minor_send() is racing somehow against capi_recv_message(), which
call both capiminor_del_ack(). So if an IRQ occurs in the middle of
capiminor_del_ack() and another instance of it is invoked, it leads to
linked list corruption.
I came up with the following patch. With this, I could not reproduce the
crash anymore. Clearly, this is not the correct fix for the issue. As this
seems to be some locking issue, there might be more locking issues in that
code. For example, doesn't the whole struct capiminor have to be locked
somehow?
Cc: Carsten Paeth <calle@calle.de>
Cc: Kai Germaschewski <kai.germaschewski@gmx.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a GTOD clocksource driver based on the Geode SCx200's Hi-Res Timer.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a CLOCKSOURCE_MASK macro to simplify initializing the mask for a struct
clocksource, and use it to replace literal mask constants in the various
clocksource drivers.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- written on init only, accessed for every timer read --> __read_mostly
- fix broken sentence
Signed-off-by: Andreas Mohr <andi@lisas.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As suggested by Roman Zippel, change clocksource functions to use
clocksource_xyz rather then xyz_clocksource to avoid polluting the
namespace.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the time sources for i386 (acpi_pm, cyclone, hpet, pit, and tsc).
With this patch, the conversion of the i386 arch to the generic timekeeping
code should be complete.
The patch should be fairly straight forward, only adding the new clocksources.
[hirofumi@mail.parknet.co.jp: acpi_pm cleanup]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As part of the i386 conversion to the generic timekeeping infrastructure, this
introduces a new tsc.c file. The code in this file replaces the TSC
initialization, management and access code currently in timer_tsc.c (which
will be removed) that we want to preserve.
The code also introduces the following functionality:
o tsc_khz: like cpu_khz but stores the TSC frequency on systems that do not
change TSC frequency w/ CPU frequency
o check/mark_tsc_unstable: accessor/modifier flag for TSC timekeeping
usability
o minor cleanups to calibration math.
This patch also includes a one line __cpuinitdata fix from Zwane Mwaikambo.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
John's about to nuke x86's monotonic clock without grepping for it first. The
patch lamely borrows the ppc64 code for x86.
hangcheck-timer shouldn't be doing it this way
a) HAVE_MONOTONIC should be CONFIG_MONOTONIC_CLOCK and it should be defined
in arch/xxx/Kconfig.
b) That ifdef tangle shouldn't be in hangcheck-timer.c. It should be using
arch-provided helper functions, which CONFIG_MONOTONIC_CLOCK-enabling
architectures implement in arch/something.c
Cc: john stultz <johnstul@us.ibm.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch series replaces the old non-generic Hardware Random Number
Generator support by a fully generic RNG API.
This makes it possible to register additional RNGs from modules. With this
patch series applied, Laptops with a bcm43xx chip (PowerBook) have a HW RNG
available now.
Additionally two new RNG drivers are added for the "ixp4xx" and "omap"
devices. (Written by Deepak Saxena). This patch series includes the old
patches by Deepak Saxena.
The old x86-rng driver has beed split.
The userspace RNG daemon can later be updated to select the RNG through
/sys/class/misc/hw_random/ for convenience. For now it is sufficient to use
cat and echo -n on the sysfs attributes.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.
Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B).
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Magic sysrq fails to work on many keyboards, particulary most of notebook
keyboards. This patch fixes it.
The idea is quite simple: Discard the SysRq break code if Alt is still being
held down. This way the broken keyboard can send the break code (or the user
with a normal keyboard can release the SysRq key) and the kernel waits until
the next key is pressed or the Alt key is released.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's a problem in drivers/bluetooth/dtl1_cs.c::dtl1_hci_send_frame()
If bt_skb_alloc() returns NULL, then skb_reserve(s, NSHL); will cause a
NULL pointer deref - ouch. If we can't allocate the resources we require
we need to tell the caller by returning -ENOMEM.
Found by the coverity checker as bug #409
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In a testament to the utter simplicity and logic of the English
language ;-), I found a single correct use - in kernel/panic.c - and
10-15 incorrect ones.
Signed-Off-By: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
We have to be able to remove SCSI devices even when they are suspended, so
QUIESCE -> CANCEL must be a legal state transition. This patch (as727)
adds the transition to the state machine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch simplifies "good_bytes" computation in sd_rw_intr().
sd: "good_bytes" computation is always done in terms of the resolution
of the device's medium, since after that it is the number of good bytes
we pass around and other layers/contexts (as opposed ot sd) can translate
that to their own resolution (block layer:512). It also makes
scsi_io_completion() processing more straightforward, eliminating the
3rd argument to the function.
It also fixes a couple of bugs like not checking return value,
using "break" instead of "return;", etc.
I've been running with this patch for some time now on a
test (do-it-all) system.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Even with the latest fixes aic79xx still occasionally triggers the
BUG_ON in slave_destroy. Rather than trying to figure out the various
levels of interaction here I've decided to remove the callback altogether.
The primary reason for the slave_alloc / slave_destroy is to keep an
index of pointers to the sdevs associated with a given target.
However, by changing the arguments to the affected functions slightly
it's possible to avoid the use of that index entirely.
The only performance penalty we'll incur is in writing the
information for /proc/scsi/XXX, as we'll have to recurse over all
available sdevs to find the correct ones. But I doubt that reading
from /proc is in any way time-critical.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to Anthony Cheung all HP XP arrays with "OPEN-"
types support REPORT_LUN. So there is no reason why we
shouldn't use it.
Signed-off-by: Anthony Cheung <anthony.cheung@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch adds support for a ZCR controller (Device ID : 0x413).
It also has a critical bug fix :
Disable controller interrupt before firing INIT cmd to FW. Interrupt
is enabled after required initialization is over. This is done to
ensure that driver is ready to handle interrupts when it is generated
by the controller.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While reviewing the IRQ autoprobing code i found the attached buglet.
probe_irq_on()/off() calls must always be in pairs, because the generic IRQ
code uses a global semaphore to serialize all autoprobing activites.
(which does make sense) The ARM code's probe_irq_*() implementation does
not do this, but if this driver is ever used on another platform, this bug
might bite.
(It probably does not trigger in practice, because a zero probing mask
returned should be rare - but still.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a condition where ibmvscsi treats a transport error as a
"busy" condition, so no errors were returned to the scsi mid-layer.
In a RAID environment this means that I/O hung rather than failing
over.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- add 'virtual_gb' parameter to simulate large storage
(by wrapping in dev_size_mb megabytes of actual ram)
- add 'no_lun_0' parameter to skip lun 0 on each target
(but still respond as required to INQUIRY + REPORT LUNS)
- add well know lu support
- add MODE SELECT commands support [pages: 0xa and 0x1c]
- add LOG SENSE command support [pages: 0xd and 0x2f]
- add READ CAPACITY (16) support
- increase number of mode pages supported (to read),
mainly transport specific (SAS) mode (sub)pages
- add more VPD pages and extend others, including
ATA information VPD page
- START STOP UNIT now maintains a state machine
- READ (16) and WRITE (16) cope with lbas larger
than 32 bits (needed for the 'virtual_gb' parameter)
- allow single command transfers up to 32 MB
- more precise error (sense data) messages
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
V4L2_CID_MPEG_STREAM_VBI_FMT controls if and how VBI data is embedded in
an MPEG stream. Currently only one format is supported: the format designed
for the ivtv driver. This should be extended with new standard formats
(such as defined for DVB) in the future.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes the weird and incorrect condition in VIDIOC_S_FREQUENCY.
The tuner should always be switched to the mode specified in the
v4l2_frequency struct. Much simpler and also corresponding to the
v4l2 specification.
The old condition made it impossible to switch from radio to
analog tv mode using VIDIOC_S_FREQUENCY. Instead the (tv) frequency would
be given to the radio tuner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for the msp34x5 audio dac. Analog sound output of
Technotrend DVB-C 2300 (aka Hauppauge Nexus-CA) works now.
Signed-off-by: Tim Kaiser <timkaiser@t-online.de>
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Oliver Endriss for spotting this.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch creates a new Kconfig menu option, entitled,
"Blackbird MPEG encoder support (cx2388x + cx23416)"
so that the cx88-blackbird mpeg encoder module can be
chosen separately.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx2341x mpeg encoder module is used by cx88-blackbird, pvrusb2 and
the external ivtv driver. This patch allows for cx2341x to be selected without
having to also select cx88-blackbird. This will be needed to build the external
ivtv driver or the standalone pvrusb2 driver against kernel 2.6.18
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Johannes Stezenbach for pointing it out
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
i386 assembly has more compact instructions for accessing 7-bit offsets.
So by moving the large members to the end of the structure we can save
quite a bit of code size. This patch shaves about 10% or 300 bytes off
the padlock-aes file.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Up until now algorithms have been happy to get a context pointer since
they know everything that's in the tfm already (e.g., alignment, block
size).
However, once we have parameterised algorithms, such information will
be specific to each tfm. So the algorithm API needs to be changed to
pass the tfm structure instead of the context pointer.
This patch is basically a text substitution. The only tricky bit is
the assembly routines that need to get the context pointer offset
through asm-offsets.h.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The 'private' member of struct input_dev is a void*, so no need to
cast it when assigning it to a struct iforce* variable.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the H-Wheel present on Microsoft Intellimouse 4.0
(AKA "tilt mouse")
Signed-off-by: Pozsar Balazs <pozsy@uhulinux.hu>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make atkbd report HANGEUL/HANJA keys by default and use correct scan
codes for these keys (they were swapped). Also make sure their scancodes
reported as EV_MSC/MSC_SCAN events.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix a mispelling of the korean alphabet name in the input subsystem.
See http://en.wikipedia.org/wiki/Hangeul#Names for more details.
KEY_HANGUEL left to not break people
Signed-off-by: Jerome Pinot <ngc891@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add an input device for the button and lid switch so that userspace gets
notified about the user pressing them via the standard input layer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Name, phys and uniq are quite often constant strings in moules implementing
particular input device. If a module unregisters input device and then gets
unloaded, the device could still be present in memory (pinned via sysfs),
but aforementioned members would point to some random memory. Set them all
to NULL when unregistering so sysfs handlers won't try dereferencing them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Change all sprintfs into snprintfs to make sure we won't stomp on
data adjacent to our buffers.
Noticed by Wouter Paesen <wouter@kangaroot.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Treat HW coordination as independent CPUs.
This enables per-cpu monintoring of P-states
http://bugzilla.kernel.org/show_bug.cgi?id=5737
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ColdFire serial driver support for the new 532x CPU family UARTs.
Patch submitted by Matt Waddel <Matt.Waddel@freescale.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Specify the struct mapping used on the new Freescale 532x CPU family's
FEC ethernet core.
Patch submitted by Matt Waddel <Matt.Waddel@freescale.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: iSER Kconfig and Makefile
IB/iser: iSER handling of memory for RDMA
IB/iser: iSER RDMA CM (CMA) and IB verbs interaction
IB/iser: iSER initiator iSCSI PDU and TX/RX
IB/iser: iSCSI iSER transport provider high level code
IB/iser: iSCSI iSER transport provider header file
IB/uverbs: Remove unnecessary list_del()s
IB/uverbs: Don't free wr list when it's known to be empty
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (51 commits)
nfs: remove nfs_put_link()
nfs-build-fix-99
git-nfs-build-fixes
Merge branch 'odirect'
NFS: alloc nfs_read/write_data as direct I/O is scheduled
NFS: Eliminate nfs_get_user_pages()
NFS: refactor nfs_direct_free_user_pages
NFS: remove user_addr, user_count, and pos from nfs_direct_req
NFS: "open code" the NFS direct write rescheduler
NFS: Separate functions for counting outstanding NFS direct I/Os
NLM: Fix reclaim races
NLM: sem to mutex conversion
locks.c: add the fl_owner to nlm_compare_locks
NFS: Display the chosen RPCSEC_GSS security flavour in /proc/mounts
NFS: Split fs/nfs/inode.c
NFS: Fix typo in nfs_do_clone_mount()
NFS: Fix compile errors introduced by referrals patches
NFSv4: Ensure that referral mounts bind to a reserved port
NFSv4: A root pathname is sent as a zero component4
NFSv4: Follow a referral
...
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (244 commits)
V4L/DVB (4210b): git-dvb: tea575x-tuner build fix
V4L/DVB (4210a): git-dvb versus matroxfb
V4L/DVB (4209): Added some BTTV PCI IDs for newer boards
Fixes some sync issues between V4L/DVB development and GIT
V4L/DVB (4206): Cx88-blackbird: always set encoder height based on tvnorm->id
V4L/DVB (4205): Merge tda9887 module into tuner.
V4L/DVB (4203): Explicitly set the enum values.
V4L/DVB (4202): allow selecting CX2341x port mode
V4L/DVB (4200): Disable bitrate_mode when encoding mpeg-1.
V4L/DVB (4199): Add cx2341x-specific control array to cx2341x.c
V4L/DVB (4198): Avoid newer usages of obsoleted experimental MPEGCOMP API
V4L/DVB (4197): Port new MPEG API to saa7134-empress with saa6752hs
V4L/DVB (4196): Port cx88-blackbird to the new MPEG API.
V4L/DVB (4193): Update cx2341x fw encoding API doc.
V4L/DVB (4192): Use control helpers for saa7115, cx25840, msp3400.
V4L/DVB (4191): Add CX2341X MPEG encoder module.
V4L/DVB (4190): Add helper functions for control processing to v4l2-common.
V4L/DVB (4189): Add videodev support for VIDIOC_S/G/TRY_EXT_CTRLS.
V4L/DVB (4188): Add new MPEG control/ioctl definitions to videodev2.h
V4L/DVB (4186): Add support for the DNTV Live! mini DVB-T card.
...
Add support for SyncLink GT2 adapter to driver.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix diagnostics error reporting that was being overwritten by incorrect use
of return codes from individual diagnostic functions.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add ability to return HDLC CRC to user application.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add custom HDLC idle pattern feature.
It allows the user to specify an arbitrary 8 or 16 bit repeating pattern on
the transmit data pin between HDLC frames.
In most cases the idle pattern is continuous ones or flags as supported by off
the shelf synchronous controllers and defined in the ISO3309 standard. Some
applications (radio/satellite modems, connections to legacy military hardware)
require non-standard patterns.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/net/irda/irda-usb.c: In function 'stir421x_patch_device':
drivers/net/irda/irda-usb.c:1108: warning: format '%u' expects type 'unsigned int', but argument 4 has type 'size_t'
Cc: Greg KH <greg@kroah.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add DMI interface functions to a new Firmware Interfaces chapter in the
kernel-api DocBook. Clean up kernel-doc in drivers/firmware/dmi_scan.c.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an LED trigger acts like a heart beat. This can be used as a
replacement of CONFIG_HEARTBEAT code exists in some arch's timer code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: "Nish Aravamudan" <nish.aravamudan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix memory leak caused by incorrect use of tty buffer facility. tty
buffers are allocated but never processed by call to tty_flip_buffer_push
so they accumulate on the full buffer list. Current code uses the buffers
as a temporary storage for data before passing it directly to the line
discipline.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make each one fit on a line so it's easier to read. I re-ordered
COMPAQ_CISSC/0x4091, which was out of order. I double-checked these, but it
would be good if you'd also check them to make sure I didn't miss any.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cciss is full of inconsistent style ("for (" vs. "for(", lines that end with
whitespace, lines beginning with a mix of spaces & tabs, etc).
This patch changes only whitespace.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Typical Linux style is "return -EINVAL", not "return(-EINVAL)".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a few spelling errors.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's easier to verify loop bounds if the array name is mentioned the for()
statement that steps through the array.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We already print "cciss: using DAC cycles" or similar for every adapter found:
why not just identify the device we're talking about and include other useful
information?
Jeff Garzik <jeff@garzik.org>:
Although this patch is correct, I would consider using dev_printk() rather
than referencing pci_name() in printk() arguments.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should call pci_request_regions() to claim all resources the device
decodes. Previously, we claimed only the I/O port range.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If something fails after we call pci_enable_device(), we should call
pci_disable_device() before returning the failure.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update loop.c to use a kthread instead of a deprecated kernel_thread for
loop devices.
[akpm@osdl.org: don't change the thread's name]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another bunch of checks in the char drivers .put_char() and .write()
routines, where tty can never be NULL. This patch removes these checks to
save some code. Coverity choked at those with the following bug ids:
isicom.c 767, 766
specialix.c 773, 774
synclink_cs.c 779, 781
synclink_gt.c 784, 785
synclinkmp.c 784, 785
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
coverity choked at another two !tty checks, in places where tty can
never be NULL. Since it removes some code we should remove
these checks. (Coverity ids #763,#762)
Signed-off-by Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
coverity choked at two !tty checks, in places where tty can never be NULL.
Since it removes some code we should remove these checks. (Coverity ids
#763,#762)
[akpm@osdl.org: even cleaner!]
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the error case, add_msg() gets called from timer functions, so should
be using GFP_ATOMIC instead of GFP_KERNEL.
Ref: http://bugzilla.kernel.org/show_bug.cgi?id=6659. Thanks to Christian
Werner <chw@ch-werner.de> for reporting, and for the initial fix.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Priority: not critical.
Mark 3 functions __init. Saves a little memory.
This makes these functions' calls to AdvWaitEEPCmd() (which is __init)
be clean (i.e., eliminates text -> init -> text call chain).
Fix multiple section mismatch warnings:
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet3550EEPConfig' (at offset 0x7a22) and 'AdvSet38C0800EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet3550EEPConfig' (at offset 0x7a4e) and 'AdvSet38C0800EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet3550EEPConfig' (at offset 0x7a79) and 'AdvSet38C0800EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet3550EEPConfig' (at offset 0x7aa2) and 'AdvSet38C0800EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet3550EEPConfig' (at offset 0x7abb) and 'AdvSet38C0800EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C0800EEPConfig' (at offset 0x7ae0) and 'AdvSet38C1600EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C0800EEPConfig' (at offset 0x7b0c) and 'AdvSet38C1600EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C0800EEPConfig' (at offset 0x7b37) and 'AdvSet38C1600EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C0800EEPConfig' (at offset 0x7b60) and 'AdvSet38C1600EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C0800EEPConfig' (at offset 0x7b79) and 'AdvSet38C1600EEPConfig'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C1600EEPConfig' (at offset 0x7b9e) and 'AdvExeScsiQueue'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C1600EEPConfig' (at offset 0x7bca) and 'AdvExeScsiQueue'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C1600EEPConfig' (at offset 0x7bf5) and 'AdvExeScsiQueue'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C1600EEPConfig' (at offset 0x7c1e) and 'AdvExeScsiQueue'
WARNING: drivers/scsi/advansys.o - Section mismatch: reference to .init.text: from .text between 'AdvSet38C1600EEPConfig' (at offset 0x7c37) and 'AdvExeScsiQueue'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Priority: tossup.
In theory some of these (previously) __init functions could be called
after init, but that problem has not been observed AFAIK.
There were 2 cases of cleanup_module() (module_exit) calling __init
functions (clear_requested_irq() & have_requested_irq()).
These are more serious, but still not observed AFAIK.
Fix sections mismatch:
WARNING: drivers/char/ip2/ip2main.o - Section mismatch: reference to .init.text: from .text between 'cleanup_module' (at offset 0x228b) and 'ip2_loadmain'
WARNING: drivers/char/ip2/ip2main.o - Section mismatch: reference to .init.text: from .text between 'cleanup_module' (at offset 0x22ae) and 'ip2_loadmain'
WARNING: drivers/char/ip2/ip2main.o - Section mismatch: reference to .init.text: from .text between 'ip2_loadmain' (at offset 0x2501) and 'set_irq'
WARNING: drivers/char/ip2/ip2main.o - Section mismatch: reference to .init.text: from .text between 'ip2_loadmain' (at offset 0x25de) and 'set_irq'
WARNING: drivers/char/ip2/ip2main.o - Section mismatch: reference to .init.text: from .text between 'ip2_loadmain' (at offset 0x2698) and 'set_irq'
WARNING: drivers/char/ip2/ip2main.o - Section mismatch: reference to .init.text: from .text between 'ip2_loadmain' (at offset 0x2922) and 'set_irq'
WARNING: drivers/char/ip2/ip2main.o - Section mismatch: reference to .init.text: from .text between 'ip2_loadmain' (at offset 0x299e) and 'set_irq'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Priority: not critical.
Make __mcdx_init() __init and static. Saves a little memory.
Fix section mismatch warning and make the function static while there:
WARNING: drivers/cdrom/mcdx.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x8be) and 'mcdx_transfer'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Priority: not critical.
Change 3 functions from __init to __devinit.
Could be an init/probe problem in theory, but not observed, so not
high priority IMO.
Fix section mismatch warnings:
WARNING: drivers/video/tridentfb.o - Section mismatch: reference to .init.text: from .text between 'trident_pci_probe' (at offset 0x1aad) and 'trident_pci_remove'
WARNING: drivers/video/tridentfb.o - Section mismatch: reference to .init.text: from .text between 'trident_pci_probe' (at offset 0x1b22) and 'trident_pci_remove'
WARNING: drivers/video/tridentfb.o - Section mismatch: reference to .init.text: from .text between 'trident_pci_probe' (at offset 0x1b31) and 'trident_pci_remove'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
netdev->set_config can be called at any time, so these references
to __initdata would be a real problem.
However, problem has not been observed AFAIK.
Fix section mismatch warnings:
WARNING: drivers/net/wan/sdla.o - Section mismatch: reference to .init.data: from .text between 'sdla_set_config' (at offset 0x1b8e) and 'sdla_stats'
WARNING: drivers/net/wan/sdla.o - Section mismatch: reference to .init.data: from .text between 'sdla_set_config' (at offset 0x1e76) and 'sdla_stats'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- whitespace fixes (80-col display)
- one unneeded cast of void*
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds support for the RTC integrated in the Atmel AT91RM9200 SoC.
Driver was originally written for 2.4 by Rick Bronson. Then converted to
2.6 ARM RTC API by Steven Scholz. Now converted to the RTC class model.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RTC: Add exported function rtc_year_days() to calculate the tm_yday value.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the v3020 RTC from EM Microelectronic.
The v3020 RTC is designed to be connected on a bus using only one data bit.
Since any data bit may be used, it is necessary to specify this to the
driver by passing a struct v3020_platform_data pointer (see
include/linux/rtc-v3020.h) to the driver.
Part of the following code comes from the kernel patchs produced by
Compulab for their products. The original file (available here:
http://raph.people.8d.com/misc/emv3020.c) was released under the terms of
the GPL license.
[akpm@osdl.org: cleanups]
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the MAX6902 SPI RTC chip. Tested on a pxa2xx cpu.
The compulab code comes from the kernel patch the produce for their
cn-x255 board. (inside a zip file on the
http://www.compulab.co.il/x255/html/x255-developer.htm)
The original file (drivers/char/max6902.c) was GPL, which is of course
an appropriate licence:
/*
* max6902.c
*
* Driver for MAX6902 RTC
*
* Copyright (C) 2004 Compulab Ltd.
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*
*/
For reference, you can get the original file here:
http://raph.people.8d.com/misc/max6902.c
[akpm@osdl.org: cleanups]
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A port of the driver for the pcf8583 i2c rtc controller to the generic RTC
framework by Alessandro Zummo. Based on
drivers/acorn/char/{pcf8583.[hc],i2c.c}. Hopefully, acorn can be converted
too to use this driver in the future.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Import genrtc's RTC UIE emulation (CONFIG_GEN_RTC_X) to rtc-dev driver with
slight adjustments/refinements. This makes UIE-less rtc drivers work
better with programs doing read/poll on /dev/rtc, such as hwclock. This
emulation should not harm rtc drivers with UIE support, since
rtc_dev_ioctl() calls underlaying rtc driver's ioctl() first.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is an "RTC-framework" driver for DS1307 and similar RTC chips,
It should be a full replacement for the existing ds1337.c driver (using the
older RTC glue), giving a net increase in the number of RTC chips that work
out-of-the-box. There's a whole cluster of RTCs that are very similar, but
the 1337 driver was a bit too picky to work with most of them.
Still no support for RTC alarm IRQs (on chips that support them).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Driver for the simple parallel port interface on the Asix AX88796 chip on
an platform_bus.
[akpm@osdl.org: x86_64 build fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do a *partial* CodingStyle cleanup, correct some spelling in printk()'s &&
convert C++ comments to C comments - in moxa driver.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Lots of people use this. Apparently RH has for over 18 months so lets
drop EXPERIMENTAL.
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
WARNING: drivers/block/cpqarray.o - Section mismatch: reference to .init.text: from .text between 'cpqarray_register_ctlr' (at offset 0xe98) and 'alloc_cpqarray_hba'
WARNING: drivers/block/cpqarray.o - Section mismatch: reference to .init.text: from .text between 'cpqarray_register_ctlr' (at offset 0xe9c) and 'alloc_cpqarray_hba'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch from Alan that fixes a real ide-cd.c regression causing
bogus "Media Check" failures for perfectly valid Fedora install ISOs, on
certain CD-ROM drives.
This is a forward port to 2.6.16 (from RHEL) of the minimal changes for the
end of media problem. It may not be sufficient for some controllers
(promise notably) and it does not touch the locking so the error path
locking is as horked as in mainstream.
From: Ingo Molnar <mingo@elte.hu>
I have ported the patch to 2.6.17-rc4 and tested it by provoking
end-of-media IO errors with an unaligned ISO image. Unlike the vanilla
kernel, the patched kernel interpreted the error condition correctly with
512 byte granularity:
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 04 fb 78 00 00 06 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 1306080
Buffer I/O error on device hdc, logical block 163260
Buffer I/O error on device hdc, logical block 163261
Buffer I/O error on device hdc, logical block 163262
the unpatched kernel produces an incorrect error dump:
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 1306080
Buffer I/O error on device hdc, logical block 163260
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 1306088
Buffer I/O error on device hdc, logical block 163261
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 1306096
Buffer I/O error on device hdc, logical block 163262
I do not have the right type of CD-ROM drive to reproduce the end-of-media
data corruption bug myself, but this same patch in RHEL solved it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Jens Axboe <axboe@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nbd abuses file header as a changelog (and obsolete one, too), and fails to
mention GPL. This fixes it.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: <Paul.Clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- proper prototypes for the following functions:
- ctrl_alt_del() (in include/linux/reboot.h)
- getrusage() (in include/linux/resource.h)
- make the following needlessly global functions static:
- kernel_restart_prepare()
- kernel_kexec()
[akpm@osdl.org: compile fix]
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a driver for the ARM PL031 RTC found on some ARM SOCs. The driver is
fairly trivial as the RTC only provides a read/write and alarm capability.
[akpm@osdl.org: compile fix]
Signed-off-by: Deepak <dsaxena@plexity.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In both the read and write cases it will return an error if
copy_{from/to}_user faults. However, I let the driver try to read/write as
much as it can just as it normally would , then finally it returns an error
if there was one. This was the most straight forward way to handle the
error , since there isn't a clear way to clean up the buffers on error .
I moved retval in idetape_chrdev_write() down into the actual code blocks
since it's really once used there, and it conflicted with my ret variable.
Fixes the following warning,
drivers/ide/ide-tape.c: In function âidetape_copy_stage_from_userâ:
drivers/ide/ide-tape.c:2662: warning: ignoring return value of âcopy_from_userâ, declared with attribute warn_unused_result
drivers/ide/ide-tape.c: In function âidetape_copy_stage_to_userâ:
drivers/ide/ide-tape.c:2689: warning: ignoring return value of âcopy_to_userâ, declared with attribute warn_unused_result
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
