The return statement at the last line of a void function
is not necessary.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) remove mwifiex_alloc_fill_wait_queue() and
mwifiex_request_ioctl()
2) avoid dynamic allocation of wait queue
3) remove unnecessary mwifiex_error_code macros that
were used mainly by the wait queue status code
4) remove some abstraction functions
5) split mwifiex_prepare_cmd() to mwifiex_send_cmd_async()
and mwifiex_send_sync() to handle asynchronous and
synchronous commands respectively
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two variants of AR5312 dual-band devices, one single-radio
and the other one dual-radio. On the dual-radio board, the first MAC
only supports 5 GHz, even though it has a dual-band PHY. The 2.4 GHz
part of this phy is used in pass-through mode, connecting the second
MAC with the second PHY.
Disable 2.4 GHz for the first MAC on an AR5312, but only if the board
configuration indicates a dual-radio device.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EEPROM version 5.0 adds a new field for disabling AES support, having
an older version means that AES is present. This patch fixes hw AES
crypto support on AR5312 boards, which have an older EEPROM version.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AHB, the calibration data usually does not contain a valid MAC address,
the correct MAC address is stored in the board config.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct is not used in any common code, and moving it out of
the ath header makes it easier to add more driver specific ops.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a dual-radio dual-band AR5312 device, the calibration data is shared
between the 5 GHz and the 2.4 GHz radio/MAC.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Request a re-configuration of Beacon related timers
on the receipt of the first Beacon frame has to be set only
for station mode. Setting beacon sync for IBSS is causing
wrong beacon slot selection on beacon generation.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, you get this:
CC [M] drivers/net/wireless/ath/ath9k/hif_usb.o
drivers/net/wireless/ath/ath9k/hif_usb.c: In function ‘ath9k_skb_queue_complete’:
drivers/net/wireless/ath/ath9k/hif_usb.c:230:12: error: expected expression before ‘do’
make[2]: *** [drivers/net/wireless/ath/ath9k/hif_usb.o] Error 1
make[1]: *** [drivers/net/wireless/ath/ath9k] Error 2
make: *** [drivers/net/wireless/ath/] Error 2
The TX_STAT_INC macro should probably be changed to accomodate such
usage, although using a trinary operator in place of an if-else seems
questionable to me anyway.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
New debugfs files:
<debugfs_root>/ath9k_htc/<phy#>/tgt_int_stats
<debugfs_root>/ath9k_htc/<phy#>/tgt_tx_stats
<debugfs_root>/ath9k_htc/<phy#>/tgt_rx_stats
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission needs to involve as little latency
as possible after receiving a SWBA event from the target.
Since packets are buffered to use TX stream mode, beacon
frames sometimes gets queued up and are not sent out immediately.
Fix this by decoupling management frame transmission from the
normal data path and send them out immediately.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally, a WMI event would arrive ahead of the TX
URB completion handler. Discarding these events would exhaust
the available TX slots, so handle them by running a timer
cleaning up such events. Also, timeout packets for which TX
completion events have not arrived.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the infrastructure is in place, process WMI
TX status events and complete packets.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station entry is removed, there could still be
pending packets destined for that station in the HIF layer.
Sending these to the target is not necessary, so drain them
in the driver itself.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point in looping over all the endpoints,
since the HIF layer uses the start/stop APIs only
for the TX pipe. Simplify the API accordingly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing a channel set or a reset operation the pending
frames queued up for transmission have to be flushed and
sent to mac80211. Fixing this has to be done in two separate
steps:
* Flush queued frames and kill the URB TX completion handler.
* Complete all the frames that in the TX pending queue.
This patch adds proper support for draining and all the callsites
namely, channel change/reset/idle/stop are fixed. A separate queue
is used for handling failed frames.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maintain a bitmap of slots for transmission and update
the cookie field for every packet with the slot value.
This value would be used for matching packets when TX
completion processing is added.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to do endpoint header removal in the ISR.
Also, this is needed when TX slot management is added later on.
Use a helper function to strip the driver header.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new routine that takes an endpoint explicitly is
introduced. The normal htc_send() now retrieves the endpoint
from the packet's private data. This would be useful
in TX completion when the endpoint ID would be required.
While at it, use a helper function to map the queue to endpoint.
Data/mgmt/beacon packets use htc_send(), while WMI comamnds
pass the endpoint to HTC.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle queue start/stop properly by maintaining
a counter to check if the pending frame count has
exceeded the threshold. Otherwise, packets would be
dropped needlessly. While at it, use a simple flag
to track queue status and use helper functions too.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using a single URB for receiving WMI events is
insufficient, increase it to 64 to not lose
WMI events in high throughput situations.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This event will be generated by the target for packet completions.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new cookie field that would be filled by the host.
This can be used to match the TX status WMI event with
the appropriate packet.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current max queue length of 1024 is quite large
and unnecessary. 256 suffices well enough even for high
throughput situations.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For all packets sent through the USB_WLAN_TX_PIPE endpoint,
the private area of the SKB's tx_info can be used to store
driver-specific information. For packets sent through USB_REG_OUT_PIPE,
this will not make a difference since they are routed through a
separate routine that doesn't access the private region.
This would help in situations where TX information is required
in the URB callback.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the received SKB could be equal to
HTC_RX_FRAME_HEADER_SIZE in case of packets with phy/crc errors,
in which case they are dropped without being processed.
Fix this check so that the error counters are updated correctly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a queue to handle WMI events and schedule a tasklet
to process the events. This fixes the race between the
WMI event ISR and the SWBA tasklet when the arrival of
WMI events in quick succession could overwrite the SWBA
data before the tasklet from a previous iteration could
have been scheduled. Also, drain the WMI queue properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transmission of beacons becomes erratic when TX load
is high, since the latency involved in the generation
of a SWBA interrupt on the target to the actual sending
of a beacon is quite high for USB devices.
Fix this by adjusting the beacon response time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the CAB endpoint to send buffered multicast or
broadcast frames after each SWBA event.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set operating parameters (cwmin, cwmax) for the beacon queue
in AP mode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi-interface mode, beacons/probe responses that are
sent out must have their timestamp field updated. Calculate
the TSF adjustment value for each beaconing interface and set it
in the frame properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission is now handled through a slot mechanism.
This allows multiple beaconing interfaces to be be present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Match the beacon header with that of the firmware.
Also, the firmware reports the TSF for an SWBA, so
store it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, update the wiphy information and use the correct
device pointer when registering. This would fix ethtool.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the new FW requires backward incompatible host driver changes,
rename the FW to allow older driver versions to work with the
older FW.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the AR7010 devices supoprted by ath9k_htc are based
on version v1.1, so remove support for v1.0.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, ampdu stream is created on the first qos packet to an
HT sta. The overhead of setting up the BA session may not be
justified if the outgoing packet rate is minimal (e.g., ping). So
we only allow ampdu streams after seeing a critical number of
packets in an arbitrary one-second interval.
Based on work by Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k only available in menuconfig if PCI bus
support is enabled. However the driver is required for
the built-in wireless MACs of the Atheros AR9130/AR9132
SoCs. These SoCs have no PCI controller, the wireless
MAC is connected to the AHB bus on them.
Introduce separated config options for the supported
buses, in order to allow building of ath9h without PCI
bus support.
As a bonus, this patch removes the cross-reference of
the ATHEROS_AR71XX option which is not present in the
kernel.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not need to enable all the interrupts in mwl8k_probe_hw.
We need to enable only MWL8K_A2H_INT_OPC_DONE interrupt for sending
commands to the firmware. Keep the other interrupts masked in
mwl8k_probe_hw. Also, in mwl8k_start, where we expect other interrupts,
enable only those interrupts we are interested in.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->tx_power_next is not initialized to max supported power,
but instead default value is used, what cause errors like
[ 58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14.
[ 58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22).
if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Comment the use of local variables to reduce the number of load/store
operations on uncached memory, in hopes of not losing this optimization
accidentally in the future.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the device id in the platform driver is hardcoded to an id
which is specific to AR9130/AR9132 SOCs as it supports only wmac (wireless mac)
of these SOCs. But this needs to be dynamic when we want to support different
wmac of SOCs. So add id_table to driver to make it extendable to more SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtl8192ce does not initialize the LED correctly.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check whether index is within bounds before testing the element
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check whether index is within bounds before testing the element
Both spurChans arrays in modalHeader5G and modalHeader2G have 5 elements,
AR_EEPROM_MODAL_SPURS is defined 5. So unless a break occurs, in the
last iteration (i=5) we tried to access spurChansPtr[5] before testing
whether i was within bounds. Fix this.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the rx/tx tasklet is pending, new unnecessary interrupts may arrive.
Decrease the load by temporarily disabling the interrupts until the tasklet
has completed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pointers to the debugfs entries do not need to be saved, because they
will be recursively removed when the wiphy is unregistered.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reusing the configured retry counts from the skb cb is more efficient than
reloading the data from uncached memory.
Replace ts_longretry (unused) with ts_final_retry which contains the retry
count for the final rate only
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ACCESS_ONCE to reduce the number of redundant loads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ACCESS_ONCE to reduce the number of variable reloads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is no longer necessary for preparing mac80211 tx status
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use local variables to reduce the number of load/store operations on uncached
memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the slot time based on the mac80211 short slot vs long slot setting
instead of just forcing long slot for all CCK-enabled channels.
This slightly improves 802.11g mode performance in in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k uses 8 usec as a sifs time, extracted from the initvals, whereas the
standard requires a sifs time of 10. The difference originates from the fact
that the SIFS register has an offset of 2 usec.
Fix the SIFS time definition to use the standard value of 10 usec and subtract
2 usecs when writing the SIFS register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Subtract the difference in preamble duration (in usec) from the value
returned by ieee80211_generic_frame_duration.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During normal operation, minstrel was showing suspicious EWMA probabilities
exceeding 100%. It looks like the tx status reporting in ath5k was not
properly clearing the rate index for rates which were never attempted.
This is caused by uninitialized stale data in the on-stack tx status
information, which is reused when more frames are received.
To fix this, rely on ts->ts_final_idx to select the last attempted rate,
instead of checking whether ts->ts_rate is set.
Additionally, the conversion from the driver rate index back to the
mac80211 rate index can be dropped, as the mac80211 tx status will still
have the original rate index which was used to set up the descriptor.
Additionally, one more inaccuracy was fixed - the final rate attempt
count only needs to be increased by one if the transmission attempt was
successful.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k driver does kmalloc allocations for pcal info in a loop.
But, if one fails it was simply returning -ENOMEM without freeing
already allocated memory. This patch corrects that oversight.
Reported-by: Eugene A. Shatokhin <dame_eugene@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Fix checkpatch errors and warnings comprising of indent errors, spaces and
__packed warnings. Also fix 'make C = 2' warnings.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Older versions have not been sold and the driver does not explicitly
check for them anyway, so we can simply ignore the macRev here.
Reduces ath9k_hw size on mips by more than 2 KB.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update Tx gain 23 for all tx gain table.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export RSSI information from all the control and extension
channel chains to debugfs. Also add rx antenna information
to debugfs. This will be useful for debugging purpose.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl4965_rate_control_register() prints a message at KERN_ERR level. It
looks like it's just a debugging message, so pr_err() seems to be
overdone. But none of the similar functions in drivers/net/wireless
print a message, so let's just drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rx should only be enabled after enough rx buffers have been given to the
hardware, however ath_rx_buf_link was calling ath9k_hw_rxena after every
single added buffer.
Fix this by calling ath9k_hw_rxena directly from the rx tasklet after
completion instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I can't find any valid reason for not setting the ATH9K_RX_FILTER_PSPOLL
flag on older hardware and neither the documentation nor the reference
code mention any reason for excluding older hardware here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having separate key information definitions for
each type of key, a common key information bitmap is used.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before calling host_to_card() to send the cmd to firmware,
we use skb_push() to add 4 bytes SDIO interface header at
the start of the data buffer. Since cmd_skb data structure
will be re-used at a later time, we need to restore its
headroom by removing the 4 bytes header.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.
The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.
The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function returns true if there is atleast one frame
in any one of the tx queues.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the correct module name and device interface so that
ethtool can display the proper values.
The firmware version will be fixed later on when the FW
can actually report a version. :)
Reported-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Tested-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.
This typically shows up in the kernel log with messages like these:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]
When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.
This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, IWLWIFI_LEGACY has to be selected independently before the
drivers are made available.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This patch fixes a very serious off-by-one bug in
the driver, which could leave the device in an
unresponsive state.
The problem was that the extra_len variable [used to
reserve extra scratch buffer space for the firmware]
was left uninitialized. Because p54_assign_address
later needs the value to reserve additional space,
the resulting frame could be to big for the small
device's memory window and everything would
immediately come to a grinding halt.
Reference: https://bugs.launchpad.net/bugs/722185
Cc: <stable@kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jason Conti <jason.conti@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These missing chip wakeups mainly cause crashes on AR5416 cards in MIPS
boards, but have also been reported to cause radio stability issues on
AR9285.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we maintain API properly, then there isn't
really a reason to warn about this since we'll
just be adding things that are safe to ignore,
so downgrade the warning to debug info level.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There's no need to keep both normal and BT statistics
versions around all the time in memory when we only
use a subset of both. So keep only the subsets that
we need in memory, depending on the debug config).
Also, in doing so, we can remove all the calls to
iwl_bt_statistics() in the driver as we'll just
access the copied statistics now.
Finally, also remove this call from the one place
where it might still be needed and automatically
detect what kind of statistics the device is sending
based on their size. This way, we don't need to keep
track of which devices do what any more, which is
good since this is subject to change based on the
ucode version (as some ucode even for non-BT devices
will in fact use BT statistics).
Warn upon encountering a statistics command from the
ucode that isn't known, so we will find such issues
earlier in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If change_interface gets invoked during a firmware
restart, it may crash; prevent that from happening
by checking if ctx->vif is assigned.
Additionally, in my initial commit I forgot to set
the vif->p2p variable correctly, so fix that too.
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The microcode may sometimes reject TX frames when
on a radar channel even after we associated as it
clears information during association and needs to
receive a new beacon before allowing that channel
again. This manifests itself as a TX status value
of TX_STATUS_FAIL_PASSIVE_NO_RX. So in this case,
stop the corresponding queue and give the frame
back to mac80211 for retransmission. We start the
queue again when a beacon from the AP is received
which will make the regulatory enforcement in the
device allow transmitting again.
Signed-off-by: Garen Tamrazian <garenx.tamrazian@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
define of firmware filenames use extra macro to build the files name.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This generates a massive reduction in module size:
with debug:
text data bss dec hex filename
670300 13136 420 683856 a6f50 iwlagn.ko (before)
388347 13136 408 401891 621e3 iwlagn.ko (after)
without debug:
text data bss dec hex filename
528575 13072 420 542067 84573 iwlagn.ko (before)
294192 13072 408 307672 4b1d8 iwlagn.ko (after)
This also removes all the IO debug functionality since
it can easily be replaced by tracing, and makes the
code unnecessarily complex.
I haven't done any CPU utilisation measurements, but
given that the hotpaths don't use much IO it is not
likely to have a negative impact; in fact, the size
reduction will reduce cache pressure which possibly
improves performance.
Finally, an unused function or two were removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ISR (interrupt service routine) ops are now
no longer necessary since they are the same for
all devices this driver now handles.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never use the value in alloc_rxb_page,
so there's no point in keeping it either.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rev_id variable is only printed, we
don't need to store it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw_rev variable is used only during init,
so there's no need to keep it around.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable is never used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Again, a 4965 specific code path that we no
longer need in iwlagn.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We know after loading the ucode whether it will
support PAN or not, so we can also initialise
the cmd_queue variable much earlier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices newer than 4965 don't actually send
two different versions of the ALIVE command,
so we always had a bug here since before this
patch we copy more data than we got. Remove
the iwl_init_alive_resp struct and don't use
it.
Since we also really don't need to track all
the data received in ALIVE as we only use the
error and log event tables later, we can also
save space by just keeping those and not more
data around in memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch left a message talking about
bootstrap, but that's clearly bogus.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some new devices and microcode files will a greater
variety of features, so the TLV-per-feature approach
we took before will quickly make things harder to
manage and increase the file size.
Add a new TLV that has feature flags. Currently, it
will contain:
1) a PAN feature flag, which moves from a separate
TLV
2) a new BT stats bit that indicates whether the
microcode image uses bluetooth statistics
3) a new MFP flag for management frame protection
which can be enabled once the device/microcode
supports it
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In alive notify, we should check return code instead of assume everything ok
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was used only on 4965 in conjunction with
the bootstrap ucode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ucode restart has to take into account a number
of things, like clearing the HCMD_ACTIVE and other
status bits, and waking up the wait_command_queue.
Currently, however, there are a number of places
that neither do that, nor actually set the FW error
bit that leads to proper restart handling, which
means that in those cases things will probably just
hang completely.
To clean this up, make all ucode restart go through
a single function, except for the cases where it's
called during firmware loading.
Also fix a bug in wimax coexist restart avoidance,
it needs to first clear the status bits (and it has
to clear the HCMD_ACTIVE one as well) and then wake
up anything waiting on wait_command_queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only 4965 had a bootstrap microcode image, so
the agn driver can completely ignore that and
we can remove some code from it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we loaded a ucode, there's no point in
checking any one that is present, we know
which one is supposed to be present so also
verify that it is exactly the right one.
That also simplifies the code and makes it
faster since it doesn't have to check all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in iwlcore_verify_inst_sparse really
doesn't need to keep track of the number of
errors it encountered since a single one is
fatal.
Also, the code in iwl_verify_inst_full is just
used to print out some things, so rename it to
iwl_print_inst and don't give it a return code
and just make it print out the values.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In alive notification call, return the status from iwl_send_calib_results()
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of places just use a variable to return
it right away, which is useless, so let's remove
the variables there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All agn devices behave the same, so there's no
need to go through function pointers for any
of the ucode loading functionality.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that these handlers are no longer shared
between 4965 and agn, they can be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver was split, a bunch of definitions
for the 3945 and 4965 devices stayed around, but
they're now useless so remove (some of) them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some code was removed, but a variable it used
and that is now unused stayed around, kill it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of configuring tx power unconditionally, check for
IEEE80211_CONF_CHANGE_POWER and configure it only when stack
sets this flag
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current ath9k code does not handle beacon timers on opmode
specific. One such example is that a STA beacon config overwrites
already configured AP vif's beacon timers during scan.
On multi station vif case, configure beacon timers beased
on primary vif selected. This also helps while moving back
to single STA vif from multi STA vifs, where the power save
is enabled and hw has to be reconfigured with proper
beacon and bssid/aid. Otherwise connection poll will be triggered
so frequently due to beacon loss.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now bssid/aid is overridden with recently changed vif's
bss config. This may cause improper beacon updation due to
bssid/aid mismatch. On station mode, select an associated
sta vif as primary vif and configure that vif's bss into hw.
Update the primary vif on interface change and bss info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused bssid from ath_vif and set av_bslot on beacon
alloc/return.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The present check denies the IBSS interface addtion if we
already have any other vifs. But it fails to deny interface
addition if IBSS was already present.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Nokia N900 the wl1251 consumes the most power when the interface is up
but not associated to access point (that supports PSM). In terms of battery
current consumption, the consumption is ~180 mA higher when the interface is
up but not associated and only ~5 mA higher when associated compared to
interface down and driver not loaded cases.
This patch adds support for the mac80211 idle notifications. Chip is put into
idle very much the same way when entering into PSM by utilizing the Extreme
Low Power (ELP) mode. I.e. idle is entered by setting necessary conditions
in wl1251_ps_set_mode followed by a call to wl1251_ps_elp_sleep.
It seems it is just enough the authorize ELP mode followed by
CMD_DISCONNECT (thanks to Kalle Valo about the idea to use it).
Without disconnect command the chip remains somewhat active and stays
consuming ~20 mA. Idle mode is left by same way than PSM. The wl1251_join
call is used to revert the CMD_DISCONNECT. Without it association to AP
doesn't work when trying second time.
With this patch the interface up but not associated case the battery current
consumption is less than 1 mA higher compared to interface down case.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFC for WL1251 idle mode support brought a few issues that are worth to
update before adding the idle mode support.
Since the idle mode can reuse the code that is now used in Power Save Mode
(PSM), the flag psm in struct wl1251 is changed to variable station_mode
to be able to distinguish between PSM and idle modes.
As the station mode is different than the power power save mode command
that is sent to chip, the enum wl1251_cmd_ps_mod values are used only when
communicating with the chip and new enum wl1251_station_mode values are used
inside the driver.
Confusing comment about psm and elp relation is removed since the PSM is
actually activated by putting the chip into Entreme Low Power (ELP) mode.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With compat-wireless CR* macros in zd_usb.h conflict with CR macros in
include/asm-generic/termbits.h. So rename CR* macros to ZD_CR*.
Conversion was done with using sed and then 'over 80 character line'
checkpatch.pl warnings and comment indents were fixed.
Reported-by: Walter Goldens <goldenstranger@yahoo.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the beacon timers are global, the individual vif type should not
be used to determine the beacon timer configuration mode, use the
global opmode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent cleanups in the beacon code fixed SWBA backoff calculation,
however it did not remove a line of code that worked around the issues
from the earlier version of the code.
After the cleanup, the initial TSF based slot calculation now always
returns 0 instead of ATH_BCBUF-1, so the previous hack that reversed the
slot order needs to be removed, as ad-hoc mode does not use staggered
beacons.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When testing wpa_supplicant with 'nl80211' driver to connect
to an AP with WPA/WPA2 security, we notice the followings:
1) add_key is called firstly with the key from cfg80211
2) set_defaut_key is called next
set_default_key() is specific to WEP keys and should not be
called in case of WPA/WPA2 security. The set_default_key()
won't be called if wpa_supplicant uses "-Dwext" option,
but it's been called if "-Dnl80211" option is specified.
We can fix this issue by adding a check to return from
set_default_key() if WEP key is not configured.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We now use priv->mutex to serialize sync command, remove old
priv->sync_cmd_mutex and add assertion that priv->mutex must be locked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check status bits with mutex taken, because when we wait for mutex
unlock, status can change. Patch should also make remaining sync
commands be send with priv->mutex taken. That will prevent execute
these commands when we are currently reset firmware, what could
possibly cause troubles.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We mark command as huge by using meta->flags from other (non huge) command,
but flags can be possibly overridden, when non huge command is enqueued,
what can lead to:
WARNING: at lib/dma-debug.c:696 dma_debug_device_change+0x1a3/0x1f0()
DMA-API: device driver has pending DMA allocations while released from device [count=1]
To fix introduce additional CMD_MAPPED to mark command as mapped and
serialize iwl_enqueue_hcmd() with iwl_tx_cmd_complete() using
hcmd_lock. Serialization will also fix possible race conditions,
because q->read_ptr, q->write_ptr are modified/used in parallel.
On the way fix whitespace.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Culler reported a problem with his AR9170 device:
> ath: EEPROM regdomain: 0x5c
> ath: EEPROM indicates we should expect a direct regpair map
> ath: invalid regulatory domain/country code 0x5c
> ath: Invalid EEPROM contents
It turned out that the regdomain 'APL7_FCCA' was not mapped yet.
According to Luis R. Rodriguez [Atheros' engineer] APL7 maps to
FCC_CTL and FCCA maps to FCC_CTL as well, so the attached patch
should be correct.
Cc: <stable@kernel.org>
Reported-by: Joe Culler <joe.culler@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the mwl8k driver attempts and fails to switch from sta to ap
firmware (or vice-versa) in the mwl8k_add_interface routine, the
mwl8k_stop routine will be called. This routine must not attempt
to free the irq if it was not requested.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least EEPROM version 0x11A has the wrong
number of chains programmed into it for some
reason, so we need to override in the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These macros are leftover of previous cleanup patches.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct mwifiex_802_11_fixed_ies is not necessary.
struct mwifiex_event_wep_icv_err is not used any more.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove redundant structures and unused macros
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These definitions are no longer used after previous cleanups.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The radio_on variable is defined but never used.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace them with NL80211_AUTHTYPE_ macros
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace them with NL80211_IFTYPE_ macros
Also remove redundant functions mwifiex_drv_get_mode()
and mwifiex_bss_ioctl_mode().
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We already tell mac80211 to stop the queue when we hit a certain
threshold. Hence, it shouldn't happen at all that a frame gets queued
for tx on a full queue. Add an error message for this case.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some clients seem to rely upon the reception of BlockAckReqs to flush
their rx reorder buffer. In order to fix aggregation for these clients
rt2x00 should send a BlockAckReq if the transmission of an AMPDU
subframe fails.
Introduce a new flag TXDONE_AMPDU to indicate that this is an AMPDU
subframe and pass IEEE80211_TX_STAT_AMPDU_NO_BACK to mac80211 if an
AMPDU subframe failed during transmission.
This fixes aggregation problems with Intel 5100 Windows STAs (and maybe
others as well).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STBC transmissions rt2x00 used the number of RxSTBC streams the
destination STA indicates in its HT capabilities as STBC value in
the TXWI.
However, the legacy drivers and our own comment in rt2800.h suggest
that the STBC field in the TXWI only allows a value of 0 or 1.
The values 2 and 3 are reserved (probably for future devices).
And indeed, STBC transmissions to STAs indicating more then 1
RxSTBC stream fail when the STBC field is set to something >1.
Fix this by only setting the STBC field to 1 when STBC should be
used.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 devices should adjust their tx power in accordance with the
eeproms temperature calibration values. Add a new driver callback
gain_calibration that is called every 4 seconds.
The rt2800 gain calibration routine simply runs the tx power
configuration that takes care of calculating the temperature
compensation delta.
We don't need to synchronize the calls to rt2800_config_txpower
as they should all happen from mac80211's single threaded workqueue.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit d1c3a37cee ("mac80211:
clarify alignment docs, fix up alignment") removed the requirement
for a 4-byte aligned payload rt2x00queue_align_payload is obsolete
as mac80211 will align the payload when it passes the frame to the
net stack.
As a result we can remove the call to rt2x00queue_align_payload in the
rx path and since that's the last user we can remove
rt2x00queue_align_payload altogether.
One advantage is that we save some alignment operations for frames
that don't need to be aligned (for example beause they are not passed
to the net stack).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the indention in rt2800_compesate_txpower and also fix a typo in
the function name rt2800_compesate_txpower -> rt2800_compensate_txpower.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the HT40 tx power compensation value was calculated for each
rate. However, the calculation is independent of the tx rate and as such
can be precalculated and just passed in for each rate.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the HT40 check inside the calculation function to make it easier
for a later cleanup.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can simply check if the driver registered the watchdog callback.
There's no need to have an additional flag for that.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the tx status fifo size as 512 calculate it based
on the number of tx queues and the number of entries per queue. Also
round the size up to a power of 2 as kfifo would otherwise round it
down.
On rt2800pci this will increase the kfifo size from 512 bytes to 1024
bytes which is then able to hold the tx status for all entries in all
tx queues.
Furthermore, if the number of tx queues or tx entries changes in the
future (use of the MGMT queue for example) the kfifo size doesn't need
to be updated.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of reporting an unlimited number of tx status reports to
mac80211 stop after 16 frames and reschedule the tx status tasklet.
This allows other tasklets to be run inbetween.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of receiving an unlimited number of frames, stop after 16
entries and reschedule the rxdone tasklet. This allows other tasklets
to be run inbetween.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some unused variables and correct spelling errors.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw_dot_11n_dev_cap reported by firmware hw_spec
has different format than the 11n capabilities.
Hence a lot of SET_ and RESET_ bit operation macros
were used to convert the dev_cap format to 11n
capability format. However the locally defined 11n
ht_cap macros are not necessary as we can use
IEEE80211_HT_CAP_ macros directly.
The 32-bit dev_cap bitmap is added as comment to
explain the mapping between firmware and 11n spec.
Some unused macros and unnecessary adapter variables
are also removed.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and SHORT_SLOT_TIME_ENABLED.
Use WLAN_CAPABILITY_SHORT_SLOT_TIME instead.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex_set_encrypt_mode()
mwifiex_set_auth_mode()
mwifiex_set_auth()
These functions are confusing and misleading.
And they are really not needed at all.
Some unused definitions are also removed.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'iw list' is sufficient to retrieve the information which
was displayed by these functions.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is nowhere used.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This does not seems to be used anywhere so remove it.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of these devices have appeared "in the wild", and apparently
the Windows driver is perfectly happy to support this EEPROM version.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
{rx,tx}done_work's are only initialized for usb devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@kernel.org
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some compiler/architecture combinations generate some warnings that are
not seen on my main system. Two of the "warnings" about unitialized variables
are really bugs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: <stable@kernel.org>
Reported-by: Mark Davis [via p54/devices wiki]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were allocating the size of the NVS file struct and not checking
whether the length of the buffer passed was correct before copying it
into the allocated memory. This is a security hole because buffer
overflows can occur if the userspace passes a bigger file than what is
expected.
With this patch, we check if the size of the data passed from
userspace matches the size required.
This bug was introduced in 2.6.36.
Cc: stable@kernel.org
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2.6.38 added WARN_ON(in_irq) in del_timer_sync that triggers on zd1211rw when
reseting rx idle timer in urb completion handler.
Move timer reseting to tasklet.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes the bogus flag introduced by upstream commit
eefdbec1ea. Old code had buffer length check
that new code tried to handle with URB_SHORT_NOT_OK flag. With USB debugging
enabled bogus flag caused usb_submit_urb fail.
Remove URB_SHORT_NOT_OK flag and add buffer length check to urb completion
handler.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32092
Reported-by: Jonathan Callen <abcd@gentoo.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The phy information print during driver init time doesn't show
the numeric part of the chip name properly for AR9485. This patch
addresses this issue by adding the string to the respective array.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MODULE_AUTHOR() macro in the main module (wl12xx) has been updated
to reflect one of the author's new email address, but the wl12xx_spi
and wl12xx_sdio modules haven't been updated. This patches updates
them.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On error path kfree() should get pointer to memory allocated by
kmalloc() not the address of variable holding it (which is on stack).
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for the USB ethernet devices suggests that
only some devices are supposed to use usb0 as the network interface
name instead of eth0. The logic used there, and documented in
Kconfig for CDC is that eth0 will be used when the mac address
is a globally assigned one, but usb0 is used for the locally
managed range that is typically used on point-to-point links.
Unfortunately, this has caused a lot of pain on the smsc95xx
device that is used on the popular pandaboard without an
EEPROM to store the MAC address, which causes the driver to
call random_ether_address().
Obviously, there should be a proper MAC addressed assigned to
the device, and discussions are ongoing about how to solve
this, but this patch at least makes sure that the default
interface naming gets a little saner and matches what the
user can expect based on the documentation, including for
new devices.
The approach taken here is to flag whether a device might be a
point-to-point link with the new FLAG_POINTTOPOINT setting in
the usbnet driver_info. A driver can set both FLAG_POINTTOPOINT
and FLAG_ETHER if it is not sure (e.g. cdc_ether), or just one
of the two. The usbnet framework only looks at the MAC address
for device naming if both flags are set, otherwise it trusts the
flag.
Signed-off-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Tested-by: Andy Green <andy.green@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have CONFIG_ARCH_DMA_ADDR_T_64BIT. We can fix the hacky
dma_addr_t size test cleanly.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should reduce the number of reserved completion queues from the total
number of entries. Since the queue size is power of two, not reducing the
reserved entries, caused a double queue size, which may lead to allocation
failures in some cases.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of allocation failure, tried to use the promiscuous QP
entry that was previously freed.
Now freeing this entry only in case we will not put it back to the list
of promiscuous entries.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has the same purpose (and value) as ah->config.max_txtrig_level
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the number of tx queue, the number of keycache entries depends
on the chip and shouldn't be messed with based on EEPROM data.
Remove this field and stick to using AR_KEYTABLE_SIZE
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only used in one place, and the device id check that it's based on
can be moved there as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains a field that can restrict the number of hardware queues,
however this is not only useless (all the known chips contain the same
number of hardware queues), but also potentially dangerous in case of a
misprogrammed EEPROM (could trigger driver crashes), so let's just ignore
it completely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RF_BANK_SETUP, REG_WRITE_RF_ARRAY and REG_WRITE_ARRAY are way too big,
so they shouldn't be inlined at every single callsite, especially since they
can easily be turned into real functions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's easier to read and it slightly decreases code size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the number of calls to register ops. On MIPS this reduces the
ath9k_hw binary size from 321k down to 310k
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this change, loading the address to a register read/write function
costs only one pointer dereference instead of two. On MIPS this reduces
ath9k_hw binary size from 326k down to 321k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for using RSN IBSS with ath9k. For now, this uses software
crypto for group addressed frames in RSN IBSS, but that may be
optimized in the future by extending the key cache design to support
per-STA RX GTK.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stuck beacon detection is supposed to trigger when 9 consecutive beacons
could not be sent by the hardware. When the driver runs only one active
AP mode interface, it still configures the hardware beacon timer for
4 (ATH_BCBUF) beacon slots slots, which causes stuck beacon detection
to be reset if ath9k_hw_stoptxdma clears the stuck frames between
SWBA intervals.
Fix this by not resetting the missed beacon count for empty slots and
multiplying the threshold not by the maximum number of beacon slots
but by the configured number of beacon interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Single missed (i.e. not transmitted) beacons in AP mode are not very rare
and not necessarily an indicator of strong interference, so only trigger
noise floor recalibration when multiple consecutive beacons could not
be transmitted.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP mode beacon timers in ath9k are configured in milliseconds, which breaks
when increasing ATH_BCBUF to 8 instead of 4 (due to rounding errors).
Since the hardware timers are actually configured in microseconds, it's
better to let the driver use that unit directly.
To be able to do that, the beacon interval parameter abuse for passing
certain flags needs to be removed. This is easy to do, because those flags
are completely unnecessary anyway. ATH9K_BEACON_ENA is ignored,
ATH9K_BEACON_RESET_TSF can be replaced with calling ath9k_hw_reset_tsf
from the driver directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for suspend/resume in if_spi.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver adds WiFi support for Marvell 802.11n based chipsets
with SDIO interface. Currently only SD8787 is supported. More
chipsets will be supported later.
drivers/net/wireless/mwifiex/
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Ramesh Radhakrishnan <rramesh@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only AR9485 1.1 was sold. This debloats the driver by ~14 KiB.
text data bss dec hex filename
300413 624 1056 302093 49c0d drivers/net/wireless/ath/ath9k/ath9k_hw.ko
text data bss dec hex filename
310285 624 1056 311965 4c29d drivers/net/wireless/ath/ath9k/ath9k_hw-old.ko
$ du -b ath9k_hw*
6210541 ath9k_hw.ko
6225089 ath9k_hw-old.ko
Cc: Bill Wu <bill.wu@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Forbes Tsai <Forbes.Tsai@Atheros.com>
Cc: Jesmine Chen <jesmine.chen@atheros.com>
Cc: Marvian Chen <Hou-hua.Chen@Atheros.com>
Cc: Vivek Natarajan <vivek.natarajan@atheros.com>
Cc: Bernadette Yetso <bernadette.yetso@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Acked-by: Yi-Chen Su <yi-chen.su@atheros.com>
Acked-by: Jeffrey Chung <jeffrey.chung@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This workaround called ath_txq_schedule whenever there were still pending
frames for a queue, but the queue depth was zero. Because of its its high
false positive probability (e.g. with paused TIDs) and because it is in
the way of other pending work (AP powersave fixes), it is better to remove
this code entirely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most AR9100 devices already have a chainmask of 7 (three antennas), however
on the ones that don't (rx and tx chainmask set to 5), problems with IQ
mismatch calibration have been observed.
This shows up as tx queue hangs (and subsequent hardware resets) if traffic
is sent during this type of calibration.
Forcing the rx chainmask to 7 fixes the calibration issues with no apparent
negative side effects on throughput and stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes interop issues with aggregation in combination with multi-BSSID
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some devices the correct MAC address is not in the EEPROM data, but
stored somewhere else.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices control antenna settings or other things through GPIO pins
of the wireless interface. Add a debugfs interface for changing those
and keeping them set across card resets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the ath9k debugfs directory is cleaned up by debugfs_remove_recursive,
there's no point in checking the return code of every single debugfs create
line.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Queue ADDBA requests in respective data queues to avoid ADDBA
requests and the the related data packets (to the same ra/tid)
queued in the hardware to be sent out asynchronously.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the outgoing packet rate to a particular HT station is <=6.5
Mbps, do not attempt to create an ampdu. Also, if the outgoing
rate is legacy rate, do not create an ampdu.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an ampdu stream is on, if the firmware rate adaptation
logic decides that the outgoing packet rate to the station needs
to go below 6.5Mbps (non HT rate), it sends an event indicating that
the ampdu stream needs to be destroyed. Handle this event in the driver
and destroy the ampdu stream so that the rate can go below 6.5Mbps
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specifically, handle ampdu_action and attempt to start a BA
session on receiving the first qos packet from mac80211 for
transmission to a HT sta. While the BA session is being created,
all the packets belonging to that stream will be dropped to
prevent sequence number mismatch at the recipient.
Contains contributions from:
Yogesh Powar <yogeshp@marvell.com>
Pradeep Nemavat <pnemavat@marvell.com>
Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In particular, we can now add, start, lookup, and remove streams.
Based on work by Nishant Sarmukadam <nishants@marvell.com> and
Pradeep Nemavat <pnemavat@marvell.com>.
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We now have two different kinds of queues. And the number of
AMPDU queues may vary. So we must be clear about which queues we
are dealing with. Note that when we report the number of queues
to mac80211, we only report the WMM queues.
Based on work by Yogesh Powar <yogeshp@marvell.com>.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware APIv2 adds the following enhancements:
-- capabilities are reported by the firmware
-- API supports up to 8 dedicated AMPDU streams
-- optional packet timestamping and expiration can be enabled.
Specifically, packets that are queued in firmware for longer
than 500ms will be dropped if this option is used.
Based on work by "Nishant Sarmukadam" <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specifically, APIv2 will specify a variable number of AMPDU
queues in the MWL8K_CMD_GET_HW_SPEC. So init the tx queues after
MWL8K_CMD_GET_HW_SPEC for ap fw.
Also, we make it safe to deinit queues that have not been init'd.
This happens if the mwl8k_get_hw_spec_ap routine fails, for
example.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fine-tuning register write operation and avoid unnecessay
delays for ath9k_htc driver, saves hw reset time which
improves scanning time and also solves one of the following
scenario.
Sometimes the ACK is sent by STA for assoc response is not
seen at AP side. So the AP continues to send retry assoc
responses. At the STA side, since the assoc response was
already forwarded to mac80211, it proceeded to channel change
which in turns does chip reset.
In most of the cases the chip reset was completed before
max retries are reached at AP side. Hence STA can able to ACK
the retried frames again. But in clear environment these retries
are completed within shortspan of time.
Since ath9k_htc consumes more time for hw reset, this latency
is causing dissociation by AP due to max reties are reached.
This issue was originally reported with Cisco Aironet 1250 AP
in HT40 mode in noise free environment.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By enabling buffered register write for ath9k_htc driver
avoids unnecessary dissociation while rekeying phase under
heavy traffic exchange.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing adc gain calibration for AR9287 chips is causing
throughput drops in HT40 mode. Remove ADC Gain from supported
calibration list.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We initialize exit_pending twice. It's the second initialization which
is correct. That was added in d745d472af "iwlwifi: cancel scan when
down the device".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We leak in some error paths of drivers/net/atlx/atl2.c:atl2_set_eeprom().
The memory allocated to 'eeprom_buff' is not freed when we return -EIO.
This patch fixes that up and also removes a pointless explicit cast.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a driver for the CDC Ethernet part of this modem. The
device's ID is blacklisted in cdc_ether.c and is white-listed in
this new driver because of the quirks needed to make it useful.
The modem's firmware exposes a CDC ACM port for modem control and a
CDC Ethernet port for network data. The descriptors look fine but
both ports actually are some sort of multiplexers requiring non-
standard headers added/removed from every packet or they get
ignored. All information is based on a usb traffic log from a
Windows machine.
On the Verizon 4G network I've seen speeds up to 1.1MB/s so far with
this driver, a speed-o-meter site reports 16.2Mbps/10.5Mbps.
Userspace scripts are required to talk to the CDC ACM port.
Signed-off-by: Andrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function phy_attach_direct attaches the phy and calls phy_init_hw.
phy_init_hw can fail, but the phy is still marked as attached. Successive
calls to phy_attach_direct will fail because the phy is busy.
[ 1.020000] eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:00, irq=-1)
[ 1.030000] eth1: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, irq=-1)
[ 2.050000] Sending DHCP requests .
[ 3.020000] PHY: 1:00 - Link is Up - 100/Full
[ 5.110000] ..... timed out!
[ 87.660000] IP-Config: Reopening network devices...
[ 88.190000] FEC: MDIO read timeout
[ 88.190000] eth0: could not attach to PHY
[ 88.190000] IP-Config: Failed to open eth0
[ 88.210000] FEC: MDIO read timeout
[ 88.210000] eth1: could not attach to PHY
[ 88.210000] IP-Config: Failed to open eth1
[ 88.220000] IP-Config: No network devices available.
[ 88.220000] Freeing init memory: 6968K
[...]
starting network interfaces...
ip: RTNETLINK answers: File exists
[ 94.000000] net eth0: PHY already attached
[ 94.010000] eth0: could not attach to PHY
ip: SIOCSIFFLAGS: Device or resource busy
This patch adds phy_detach to clean up if phy_init_hw fails.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
via-ircc has been passing a NULL pointer to DMA allocation functions,
which is completely invalid and results in a BUG on PowerPC. Now
that we always have the device pointer available, pass it in.
Reference: http://bugs.debian.org/619450
Reported-by: Andrew Buckeridge <andrewb@bgc.com.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Andrew Buckeridge <andrewb@bgc.com.au> [against 2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
via-ircc still maintains its own array of device pointers in Linux 2.4
style. Worse, it always uses index 0, so it will crash if there are
multiple suitable devices in the system.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If change_interface gets invoked during a firmware
restart, it may crash; prevent that from happening
by checking if ctx->vif is assigned.
Additionally, in my initial commit I forgot to set
the vif->p2p variable correctly, so fix that too.
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some clients seem to rely upon the reception of BlockAckReqs to flush
their rx reorder buffer. In order to fix aggregation for these clients
carl9170 should set IEEE80211_TX_STAT_AMPDU_NO_BACK to generate a
BlockAckReq if the transmission of an AMPDU subframe fails.
This fixes aggregation problems with Intel 5100 Windows STAs (and maybe
others as well).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After new NetworkManager 0.8.996 changes, hardware scanning is causing
microcode errors as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=683571
and sometimes kernel crashes:
https://bugzilla.redhat.com/show_bug.cgi?id=688252
Also with hw scan there are very bad performance on some systems
as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=671366
Since Intel no longer supports 3945, there is no chance to get proper
firmware fixes, we need workaround problems by disable hardware scanning
by default.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Software scanning can be used for workaround some performance problems,
so do not deprecate it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'irq-final-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (111 commits)
gpio: ab8500: Mark broken
genirq: Remove move_*irq leftovers
genirq: Remove compat code
drivers: Final irq namespace conversion
mn10300: Use generic show_interrupts()
mn10300: Cleanup irq_desc access
mn10300: Convert genirq namespace
frv: Use generic show_interrupts()
frv: Convert genirq namespace
frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
frv: Convert cpu irq_chip to new functions
frv: Convert mb93493 irq_chip to new functions
frv: Convert mb93093 irq_chip to new function
frv: Convert mb93091 irq_chip to new functions
frv: Fix typo from __do_IRQ overhaul
frv: Remove stale irq_chip.end
m68k: Convert irq function namespace
xen: Use new irq_move functions
xen: Cleanup genirq namespace
unicore32: Use generic show_interrupts()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
xfrm: Restrict extended sequence numbers to esp
xfrm: Check for esn buffer len in xfrm_new_ae
xfrm: Assign esn pointers when cloning a state
xfrm: Move the test on replay window size into the replay check functions
netdev: bfin_mac: document TE setting in RMII modes
drivers net: Fix declaration ordering in inline functions.
cxgb3: Apply interrupt coalescing settings to all queues
net: Always allocate at least 16 skb frags regardless of page size
ipv4: Don't ip_rt_put() an error pointer in RAW sockets.
net: fix ethtool->set_flags not intended -EINVAL return value
mlx4_en: Fix loss of promiscuity
tg3: Fix inline keyword usage
tg3: use <linux/io.h> and <linux/uaccess.h> instead <asm/io.h> and <asm/uaccess.h>
net: use CHECKSUM_NONE instead of magic number
Net / jme: Do not use legacy PCI power management
myri10ge: small rx_done refactoring
bridge: notify applications if address of bridge device changes
ipv4: Fix IP timestamp option (IPOPT_TS_PRESPEC) handling in ip_options_echo()
can: c_can: Fix tx_bytes accounting
can: c_can_platform: fix irq check in probe
...
The current code sometimes generates build warnings due to how it checks
the silicon revision, so clean it up and properly document things.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct usage should be "static inline void" instead of "static void inline"
Signed-off-by: G.Balaji <balajig81@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the performance of different receive interrupt
coalescing settings on a single stream TCP benchmark, I noticed two
very different results. With rx-usecs=50, most of the time a
connection would hit 8280 Mbps but once in a while it would hit
9330 Mbps.
It turns out we are only applying the interrupt coalescing settings
to the first queue and whenever the rx hash would direct us onto
that queue we ran faster.
With this patch applied and rx-usecs=50, I get 9330 Mbps
consistently.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the chip is still asleep when ath9k_start is called,
ath9k_hw_configpcipowersave can trigger a data bus error.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After commit d5dbda2380 "ethtool: Add
support for vlan accleration.", drivers that have NETIF_F_HW_VLAN_TX,
and/or NETIF_F_HW_VLAN_RX feature, but do not allow enable/disable vlan
acceleration via ethtool set_flags, always return -EINVAL from that
function. Fix by returning -EINVAL only if requested features do not
match current settings and can not be changed by driver.
Change any driver that define ethtool->set_flags to use
ethtool_invalid_flags() to avoid similar problems in the future
(also on drivers that do not have the problem).
Tested with modified (to reproduce this bug) myri10ge driver.
Cc: stable@kernel.org # 2.6.37+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4_en driver uses the combination stop_port/start_port
in a number of places. Unfortunately that causes any promiscuous
mode settings on the hardware to be lost.
This patch fixes that problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct usage is "static inline void" not "static void inline".
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is proper style to include linux/foo.h instead asm/foo.h if both exist
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two places in the kernel were doing skb->ip_summed = 0.
Change both to skb->ip_summed = CHECKSUM_NONE, which is more readable.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The jme driver uses the legacy PCI power management, so it has to do
some PCI-specific things in its ->suspend() and ->resume() callbacks,
which isn't necessary and should better be done by the PCI
sybsystem-level power management code. It also doesn't use device
wakeup flags correctly.
Convert jme to the new PCI power management framework and make it
let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid theoretical race condition regarding accessing dev->features
NETIF_F_LRO flag, which is illustrated below.
CPU1 CPU2
myri10ge_clean_rx_done(): myri10ge_set_flags():
or
myri10ge_set_rx_csum():
if (dev->features & NETIF_F_LRO)
setup lro
dev->features |= NETIF_F_LRO
or
dev->features &= ~NETIF_F_LRO;
if (dev->features & NETIF_F_LRO)
flush lro
On the way reduce myri10ge_rx_done() number of arguments and calls by
moving mgp->small_bytes check into that function. That reduce code size
from:
text data bss dec hex filename
36644 248 100 36992 9080 drivers/net/myri10ge/myri10ge.o
to:
text data bss dec hex filename
36037 247 100 36384 8e20 drivers/net/myri10ge/myri10ge.o
on my i686 system, what should also make myri10ge_clean_rx_done()
being faster.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current SocketCAN implementation for the Bosch c_can cell doesn't
account the TX bytes correctly, because it calls
c_can_inval_msg_object() (which clears the msg ctrl register) before
reading the DLC value:
for (/* nix */; (priv->tx_next - priv->tx_echo) > 0; priv->tx_echo++) {
msg_obj_no = get_tx_echo_msg_obj(priv);
c_can_inval_msg_object(dev, 0, msg_obj_no);
val = c_can_read_reg32(priv, &priv->regs->txrqst1);
if (!(val & (1 << msg_obj_no))) {
can_get_echo_skb(dev,
msg_obj_no - C_CAN_MSG_OBJ_TX_FIRST);
stats->tx_bytes += priv->read_reg(priv,
&priv->regs->ifregs[0].msg_cntrl)
& IF_MCONT_DLC_MASK;
stats->tx_packets++;
}
}
So, we will always read 0 for the DLC value and "ifconfig" will report
*0* TX Bytes.
The fix is quite easy: Just move c_can_inval_msg_object() to the end of
the if() statement. So:
* We only call c_can_inval_msg_object() if the message was
actually transmitted
* We read out the DLC value _before_ clearing the msg ctrl
register
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the check in the probe function whether a IRQ was supplied
to the driver. The original driver check the irq "struct resource *" against
<= 0. Use "platform_get_irq" instead.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables the one shot mode, until the driver has been fixed and
tested to support it.
> I'm quite sure I've seen a situation where msg_obj 17 "seemed" to be
> pending, while msg_obj 18 and 19 already have been transmitted. But
> in that case, I enabled ONESHOT for the can interface, which enables
> the DA mode (automatic retransmission is disabled).
Reported-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
route: Take the right src and dst addresses in ip_route_newports
ipv4: Fix nexthop caching wrt. scoping.
ipv4: Invalidate nexthop cache nh_saddr more correctly.
net: fix pch_gbe section mismatch warning
ipv4: fix fib metrics
mlx4_en: Removing HW info from ethtool -i report.
net_sched: fix THROTTLED/RUNNING race
drivers/net/a2065.c: Convert release_resource to release_region/release_mem_region
drivers/net/ariadne.c: Convert release_resource to release_region/release_mem_region
bonding: fix rx_handler locking
myri10ge: fix rmmod crash
mlx4_en: updated driver version to 1.5.4.1
mlx4_en: Using blue flame support
mlx4_core: reserve UARs for userspace consumers
mlx4_core: maintain available field in bitmap allocator
mlx4: Add blue flame support for kernel consumers
mlx4_en: Enabling new steering
mlx4: Add support for promiscuous mode in the new steering model.
mlx4: generalization of multicast steering.
mlx4_en: Reporting HW revision in ethtool -i
...
This gives much better performance at fast 3x3 rates (up to ~160 Mbps).
The scheduler will still make most decisions about batch size based on
available packets and RX parameters.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Throughout the code we use rate_n_flags & 0xff to extract the lower byte
of the rate_n_flags u32 that contains the information about the rate.
Add a #define and remove the use of the magic number.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since the driver split, there's no need for no_agg_framecnt_info since
all devices have this set to false. Secondly, the compressed block ack
handling code was broken. Fix this.
(1) A shift less than zero simply implies that the buffer wrapped, this
is expected. Remove the incorrect comment.
(2) The (agg->frame_count > (64-sh)) condition can happen if the last
frame is dropped. E.g., if I send 7 frames and the 6th is received but
the 7th is lost, the other side may only shift the window 6, not 7
frames since the last bit is a 0. This is perfectly fine behavior and
doesn't invalidate the feedback.
(3) Store the feedback from a Compressed BA in the first newly received
frame, rather than the start of the window. This way it will get
processed by the rate selection code. Feedback stored in a non-received
frame is likely to get overwritten by the retransmission.
This is based on the approach taken by minstrel_ht.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When filling out its rate scale table, iwlwifi repeats the first HT rate
IWL_HT_NUMBER_TRY times. The hardware scheduler will stop using
aggregation for any frame that fails LINK_QUAL_AGG_DISABLE_START_DEF
times. Currently, both these constants equal 3.
If iwlwifi probes a faster rate than the link supports, all frames in a
(potentially tens of frames large) batch will fail IWL_HT_NUMBER_TRY
times. Because this happens to be as large as
LINK_QUAL_AGG_DISABLE_START_DEF, all frames will then be sent
individually. This leads to a short, but performance-degrading window
where the legacy stop-and-wait MAC takes over.
Bounding the initial rate by (LINK_QUAL_AGG_DISABLE_START_DEF-1)
attempts makes the third try use a lower rate and hence more be likely
to succeed. This somewhat mitigates the above described behavior.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlagn's hardware scheduler needs to be set up
with the right aggregation frame limit and
buffer sizes. To achieve this, we need to move
the hardware queue setup to when the session
becomes operational.
Tested-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since the driver split, there's no need for
function pointers any more for aggregation
queue setup and teardown as all devices now
share the same code. Simplify this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Fix section mismatch warning by renaming the pci_driver variable to a
recognized (whitelisted) name.
WARNING: drivers/net/pch_gbe/pch_gbe.o(.data+0x1f8): Section mismatch in reference from the variable pch_gbe_pcidev to the variable .devinit.rodata:pch_gbe_pcidev_id
The variable pch_gbe_pcidev references
the variable __devinitconst pch_gbe_pcidev_id
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoiding abuse of ethtool_drvinfo.driver field.
HW specific info can be retrieved using lspci.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Increase DMA max_segment_size on Mellanox hardware
IB/mad: Improve an error message so error code is included
RDMA/nes: Don't print success message at level KERN_ERR
RDMA/addr: Fix return of uninitialized ret value
IB/srp: try to use larger FMR sizes to cover our mappings
IB/srp: add support for indirect tables that don't fit in SRP_CMD
IB/srp: rework mapping engine to use multiple FMR entries
IB/srp: allow sg_tablesize to be set for each target
IB/srp: move IB CM setup completion into its own function
IB/srp: always avoid non-zero offsets into an FMR
Subsystem initialization sequence modified to support presence of multiple
RapidIO controllers in the system. The new sequence is compatible with
initialization of PCI devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Add an option to include RapidIO support if the PCI is available.
2. Add FSL_RIO configuration option to enable controller selection.
3. Add RapidIO support option into x86 and MIPS architectures.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Request_mem_region should be used with release_mem_region, not
release_resource.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,E;
@@
*x = request_mem_region(...)
... when != release_mem_region(x)
when != x = E
* release_resource(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request_mem_region should be used with release_mem_region, not
release_resource.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,E;
@@
*x = request_mem_region(...)
... when != release_mem_region(x)
when != x = E
* release_resource(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prevents possible race between bond_enslave and bond_handle_frame
as reported by Nicolas by moving rx_handler register/unregister.
slave->bond is added to hold pointer to master bonding sructure. That
way dev->master is no longer used in bond_handler_frame.
Also, this removes "BUG: scheduling while atomic" message
Reported-by: Nicolas de Pesloüan <nicolas.2p.debian@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Tested-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rmmod myri10ge crash at free_netdev() -> netif_napi_del(), because napi
structures are already deallocated. To fix call netif_napi_del() before
kfree() at myri10ge_free_slices().
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doorbell is used according to usage of BlueFlame.
For Blue Flame to work in Ethernet mode QP number should have 0
at bits 6,7.
Allocating range of QPs accordingly.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not allow a kernel consumer to allocate a UAR to serve for blue flame if the
number of available UARs gets below MLX4_NUM_RESERVED_UARS (currently 8). This
will allow userspace apps to open a device file and run things like
ibv_devinfo.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlx4_bitmap_avail() to give the number of available resources. We want to
use this as a hint to whether to allocate a resources or not. This patch is
introduced to be used with allocation blue flame registers.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using blue flame can improve latency by allowing the HW to more efficiently
access the WQE. This patch presents two functions that are used to allocate or
release HW resources for using blue flame; the caller need to supply a struct
mlx4_bf object when allocating resources. Consumers that make use of this API
should post doorbells to the UAR object pointed by the initialized struct
mlx4_bf;
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4_en module now uses the new steering mechanism.
The RX packets are now steered through the MCG table instead
of Mac table for unicast, and default entry for multicast.
The feature is enabled through INIT_HCA
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Ethernet mode only,
When we want to register QP as promiscuous, it must be added to all the
existing steering entries and also to the default one.
The promiscuous QP might also be on of "real" QPs,
which means we need to monitor every entry to avoid duplicates and ensure
we close an entry when all it has is promiscuous QPs.
Same mechanism both for unicast and multicast.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW revision is derived from device ID and rev id.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver queries the FW for WOL support.
Ethtool get/set_wol is implemented accordingly.
Only magic packets are supported at the time.
Signed-off-by: Igor Yarovinsky <igory@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each RX ring will have its own interrupt vector, and TX rings will share one
(we mostly use polling for TX completions).
The vectors are assigned first time device is opened, and its name includes
the interface name and ring number.
Signed-off-by: Markuze Alex <markuze@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a pool of MSI-X vectors and EQs that can be used explicitly by mlx4_core
customers (mlx4_ib, mlx4_en). The consumers will assign their own names to the
interrupt vectors. Those vectors are not opened at mlx4 device initialization,
opened by demand.
Changed the max number of possible EQs according to the new scheme, no longer relies on
on number of cores.
The new functionality is exposed through mlx4_assign_eq() and mlx4_release_eq().
Customers that do not use the new API will get completion vectors as before.
Signed-off-by: Markuze Alex <markuze@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reseting the module parameters each ifup or mtu change,
they are being set once at device initialization
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 86271e460a introduced a
regression that caused mac80211 queues in stopped state.
ath_drain_all_txq is called in driver flush which would reset
the stopped flag and the mac80211 queues were never started
after that. iperf traffic is completely stalled due to this issue.
Restart the mac80211 queues in driver flush only if the txqs were
drained.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent tx status optimization in mac80211, we bail out as
and and when invalid rate index is found. So the behavior of resetting
rate idx to -1 and count to 0 has changed for the rate indexes that
were not part of the driver's retry series.
This has resulted in ath9k using incorrect rate table index which
caused the system to panic. Ideally ath9k need to loop only for the
indexes that were part of the retry series and so simply use hw->max_rates
as the loop counter.
Pasted the stack trace of the panic issue for reference.
[ 754.093192] BUG: unable to handle kernel paging request at ffff88046a9025b0
[ 754.093256] IP: [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
[ 754.094888] Call Trace:
[ 754.094903] <IRQ>
[ 754.094928] [<ffffffffa051f883>] ieee80211_tx_status+0x203/0x9e0 [mac80211]
[ 754.094975] [<ffffffffa053e305>] ? __ieee80211_wake_queue+0x125/0x140 [mac80211]
[ 754.095017] [<ffffffffa02e66c9>] ath_tx_complete_buf+0x1b9/0x370 [ath9k]
[ 754.095054] [<ffffffffa02e6fcf>] ath_tx_complete_aggr+0x51f/0xb50 [ath9k]
[ 754.095098] [<ffffffffa05382a3>] ? ieee80211_prepare_and_rx_handle+0x173/0xab0 [mac80211]
[ 754.095148] [<ffffffff81350e62>] ? _raw_spin_unlock_irqrestore+0x32/0x40
[ 754.095186] [<ffffffffa02e9735>] ath_tx_tasklet+0x365/0x4b0 [ath9k]
[ 754.095224] [<ffffffff8107a2a2>] ? clockevents_program_event+0x62/0xa0
[ 754.095261] [<ffffffffa02e2628>] ath9k_tasklet+0x168/0x1c0 [ath9k]
[ 754.095298] [<ffffffff8105599b>] tasklet_action+0x6b/0xe0
[ 754.095331] [<ffffffff81056278>] __do_softirq+0x98/0x120
[ 754.095361] [<ffffffff8100cd5c>] call_softirq+0x1c/0x30
[ 754.095393] [<ffffffff8100efb5>] do_softirq+0x65/0xa0
[ 754.095423] [<ffffffff810563fd>] irq_exit+0x8d/0x90
[ 754.095453] [<ffffffff8100ebc1>] do_IRQ+0x61/0xe0
[ 754.095482] [<ffffffff81351413>] ret_from_intr+0x0/0x15
[ 754.095513] <EOI>
[ 754.095531] [<ffffffff81014375>] ? native_sched_clock+0x15/0x70
[ 754.096475] [<ffffffffa02bcfa6>] ? acpi_idle_enter_bm+0x24d/0x285 [processor]
[ 754.096475] [<ffffffffa02bcf9f>] ? acpi_idle_enter_bm+0x246/0x285 [processor]
[ 754.096475] [<ffffffff8127fab2>] cpuidle_idle_call+0x82/0x100
[ 754.096475] [<ffffffff8100a236>] cpu_idle+0xa6/0xf0
[ 754.096475] [<ffffffff81339bc1>] rest_init+0x91/0xa0
[ 754.096475] [<ffffffff814efccd>] start_kernel+0x3fd/0x408
[ 754.096475] [<ffffffff814ef347>] x86_64_start_reservations+0x132/0x136
[ 754.096475] [<ffffffff814ef451>] x86_64_start_kernel+0x106/0x115
[ 754.096475] RIP [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On hardware busy the scan request pointer should be cleared, as higher
levels will release. This avoids a crash when that pointer is
erroneously used later.
Signed-off-by: Joseph J. Gunn <armadefuego@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearly a mistake, since pointers won't suddenly
change their value...
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With recent changes to the driver(switch to new cpdma layer),
the support for buffer descriptor address translation logic
is broken. This affects platforms where the physical address of
the descriptors as seen by the DMA engine is different from the
physical address.
Original Patch adding translation logic support:
Commit: ad021ae886
Signed-off-by: Sriramakrishnan A G <srk@ti.com>
Tested-By: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SR-IOV is enabled by firmware, even if it is not enabled in the PCI
capability, TX pushes using write-combining may be corrupted.
We want to know whether it is enabled before mapping the NIC
registers, and even if PCI extended capabilities are not accessible.
Therefore, we look for the MSI capability, which is removed if SR-IOV
is enabled.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Instead of always creating a huge (268K) deflate_workspace with the
maximum compression parameters (windowBits=15, memLevel=8), allow the
caller to obtain a smaller workspace by specifying smaller parameter
values.
For example, when capturing oops and panic reports to a medium with
limited capacity, such as NVRAM, compression may be the only way to
capture the whole report. In this case, a small workspace (24K works
fine) is a win, whether you allocate the workspace when you need it (i.e.,
during an oops or panic) or at boot time.
I've verified that this patch works with all accepted values of windowBits
(positive and negative), memLevel, and compression level.
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By default, each device is assumed to be able only handle 64 KB chunks
during DMA. By giving the segment size a larger value, the block layer
will coalesce more S/G entries together for SRP, allowing larger
requests with the same sg_tablesize setting. The block layer is the
only direct user of it, though a few IOMMU drivers reference it as
well for their *_map_sg coalescing code. pci-gart_64 on x86, and a
smattering on on sparc, powerpc, and ia64.
Since other IB protocols could potentially see larger segments with
this, let's check those:
- iSER is fine, because you limit your maximum request size to 512
KB, so we'll never overrun the page vector in struct iser_page_vec
(128 entries currently). It is independent of the DMA segment size,
and handles multi-page segments already.
- IPoIB is fine, as it maps each page individually, and doesn't use
ib_dma_map_sg().
- RDS appears to do the right thing and has no dependencies on DMA
segment size, but I don't claim to have done a complete audit.
- NFSoRDMA and 9p are OK -- they do not use ib_dma_map_sg(), so they
doesn't care about the coalescing.
- Lustre's ko2iblnd does not care about coalescing -- it properly
walks the returned sg list.
This patch ups the value on Mellanox hardware to 1 GB, which matches
reported firmware limits on mlx4.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
IPVS: Use global mutex in ip_vs_app.c
ipvs: fix a typo in __ip_vs_control_init()
veth: Fix the byte counters
net ipv6: Fix duplicate /proc/sys/net/ipv6/neigh directory entries.
macvlan: Fix use after free of struct macvlan_port.
net: fix incorrect spelling in drop monitor protocol
can: c_can: Do basic c_can configuration _before_ enabling the interrupts
net/appletalk: fix atalk_release use after free
ipx: fix ipx_release()
snmp: SNMP_UPD_PO_STATS_BH() always called from softirq
l2tp: fix possible oops on l2tp_eth module unload
xfrm: Fix initialize repl field of struct xfrm_state
netfilter: ipt_CLUSTERIP: fix buffer overflow
netfilter: xtables: fix reentrancy
netfilter: ipset: fix checking the type revision at create command
netfilter: ipset: fix address ranges at hash:*port* types
niu: Rename NIU parent platform device name to fix conflict.
r8169: fix a bug in rtl8169_init_phy()
bonding: fix a typo in a comment
ftmac100: use resource_size()
...
Commit 44540960 "veth: move loopback logic to common location" introduced
a bug in the packet counters. I don't understand why that happened as it
is not explained in the comments and the mut check in dev_forward_skb
retains the assumption that skb->len is the total length of the packet.
I just measured this emperically by setting up a veth pair between two
noop network namespaces setting and attempting a telnet connection between
the two. I saw three packets in each direction and the byte counters were
exactly 14*3 = 42 bytes high in each direction. I got the actual
packet lengths with tcpdump.
So remove the extra ETH_HLEN from the veth byte count totals.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the macvlan driver was extended to call unregisgter_netdevice_queue
in 23289a37e2, a use after free of struct
macvlan_port was introduced. The code in dellink relied on unregister_netdevice
actually unregistering the net device so it would be safe to free macvlan_port.
Since unregister_netdevice_queue can just queue up the unregister instead of
performing the unregiser immediately we free the macvlan_port too soon and
then the code in macvlan_stop removes the macaddress for the set of macaddress
to listen for and uses memory that has already been freed.
To fix this add a reference count to track when it is safe to free the macvlan_port
and move the call of macvlan_port_destroy into macvlan_uninit which is guaranteed
to be called after the final macvlan_port_close.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I ran into some trouble while testing the SocketCAN driver for the BOSCH
C_CAN controller. The interface is not correctly initialized, if I put
some CAN traffic on the line, _while_ the interface is being started
(which means: the interface doesn't come up correcty, if there's some RX
traffic while doing 'ifconfig can0 up').
The current implementation enables the controller interrupts _before_
doing the basic c_can configuration. I think, this should be done the
other way round.
The patch below fixes things for me.
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were found using the following semantic match:
// <smpl>
@@expression E1; type T;@@
* memset(E1, ... * sizeof(T) * ..., ...);
// </smpl>
Also take this opportunity to remove the unnecessary void* casts.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add unknown Toshiba device, mentioned in rt3572sta sources, under
CONFIG_RT2800USB_UNKNOWN
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 2L Central Europe BV 8070 under CONFIG_RT2800USB_UNKNOWN
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Planex Communications, Inc. RT8070 under CONFIG_RT2800USB_UNKNOWN
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ID for Asus USB-N11 Wi-FI adapter. Tested by me.
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing an entry from the scan_list should be performed while holding
the lock.
Signed-off-by: Joseph J. Gunn <armadefuego@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should unlock here instead of returning -EINVAL directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
commit 54405cde76 (r8169: support control of advertising.)
introduced a bug in rtl8169_init_phy()
Reported-and-tested-by: Piotr Hosowicz <piotr@hosowicz.com>
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by:: Oliver Neukum <oliver@neukum.org>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Anca Emanuel <anca.emanuel@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the OF device driver bits were converted over to the platform
device infrastructure in commit 74888760d4
("dt/net: Eliminate users of of_platform_{,un}register_driver") we
inadvertantly created probing problems in the OF case.
The NIU driver creates a dummy platform device to represent the
board that contains one or more child NIU devices. Unfortunately
we use the same name, "niu", as the OF device driver itself uses.
The result is that we try to probe the dummy "niu" parent device we
create, and since it has a NULL ofdevice pointer etc. everything
explodes:
[783019.128243] niu: niu.c:v1.1 (Apr 22, 2010)
[783019.128810] Unable to handle kernel NULL pointer dereference
[783019.128949] tsk->{mm,active_mm}->context = 000000000000039e
[783019.129078] tsk->{mm,active_mm}->pgd = fffff803afc5a000
[783019.129206] \|/ ____ \|/
[783019.129213] "@'/ .. \`@"
[783019.129220] /_| \__/ |_\
[783019.129226] \__U_/
[783019.129378] modprobe(2004): Oops [#1]
[783019.129423] TSTATE: 0000000011001602 TPC: 0000000010052ff8 TNPC: 000000000061bbb4 Y: 00000000 Not tainted
[783019.129542] TPC: <niu_of_probe+0x3c/0x2dc [niu]>
[783019.129624] g0: 8080000000000000 g1: 0000000000000000 g2: 0000000010056000 g3: 0000000000000002
[783019.129733] g4: fffff803fc1da0c0 g5: fffff800441e2000 g6: fffff803fba84000 g7: 0000000000000000
[783019.129842] o0: fffff803fe7df010 o1: 0000000010055700 o2: 0000000000000000 o3: fffff803fbacaca0
[783019.129951] o4: 0000000000000080 o5: 0000000000777908 sp: fffff803fba866e1 ret_pc: 0000000010052ff4
[783019.130083] RPC: <niu_of_probe+0x38/0x2dc [niu]>
[783019.130165] l0: fffff803fe7df010 l1: fffff803fbacafc0 l2: fffff803fbacaca0 l3: ffffffffffffffed
[783019.130273] l4: 0000000000000000 l5: 000000007fffffff l6: fffff803fba86f40 l7: 0000000000000001
[783019.130382] i0: fffff803fe7df000 i1: fffff803fc20aba0 i2: 0000000000000000 i3: 0000000000000001
[783019.130490] i4: 0000000000000000 i5: 0000000000000000 i6: fffff803fba867a1 i7: 000000000062038c
[783019.130614] I7: <platform_drv_probe+0xc/0x20>
Fix by simply renaming the parent device to "niu-board".
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 54405cde76 (r8169: support control of advertising.)
introduced a bug in rtl8169_init_phy()
Reported-by: Piotr Hosowicz <piotr@hosowicz.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Anca Emanuel <anca.emanuel@gmail.com>
Tested-by: Piotr Hosowicz <piotr@hosowicz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calculation is off-by-one. It should be "end - start + 1". This
patch fixes it to use resource_size() instead. Oddly, the code already
uses resource size correctly a couple lines earlier when it calls
request_mem_region() for this memory.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As specified by errata eTSEC49 of MPC8548 and errata eTSEC12 of MPC83xx,
older revisions of gianfar controllers will be unable to calculate a TCP/UDP
packet checksum for some alignments of the appropriate FCB. This patch checks
for FCB alignment on such controllers and falls back to software checksumming
if the alignment is known to be bad.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (27 commits)
arch/tile: support newer binutils assembler shift semantics
arch/tile: fix deadlock bugs in rwlock implementation
drivers/edac: provide support for tile architecture
tile on-chip network driver: sync up with latest fixes
arch/tile: support 4KB page size as well as 64KB
arch/tile: add some more VMSPLIT options and use consistent naming
arch/tile: fix some comments and whitespace
arch/tile: export some additional module symbols
arch/tile: enhance existing finv_buffer_remote() routine
arch/tile: fix two bugs in the backtracer code
arch/tile: use extended assembly to inline __mb_incoherent()
arch/tile: use a cleaner technique to enable interrupt for cpu_idle()
arch/tile: sync up with <arch/sim.h> and <arch/sim_def.h> changes
arch/tile: fix reversed test of strict_strtol() return value
arch/tile: avoid a simulator warning during bootup
arch/tile: export <asm/hardwall.h> to userspace
arch/tile: warn and retry if an IPI is not accepted by the target cpu
arch/tile: stop disabling INTCTRL_1 interrupts during hypervisor downcalls
arch/tile: fix __ndelay etc to work better
arch/tile: bug fix: exec'ed task thought it was still single-stepping
...
Fix up trivial conflict in arch/tile/kernel/vmlinux.lds.S (percpu
alignment vs section naming convention fix)
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
* 'config' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
BKL: That's all, folks
fs/locks.c: Remove stale FIXME left over from BKL conversion
ipx: remove the BKL
appletalk: remove the BKL
x25: remove the BKL
ufs: remove the BKL
hpfs: remove the BKL
drivers: remove extraneous includes of smp_lock.h
tracing: don't trace the BKL
adfs: remove the big kernel lock
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1480 commits)
bonding: enable netpoll without checking link status
xfrm: Refcount destination entry on xfrm_lookup
net: introduce rx_handler results and logic around that
bonding: get rid of IFF_SLAVE_INACTIVE netdev->priv_flag
bonding: wrap slave state work
net: get rid of multiple bond-related netdevice->priv_flags
bonding: register slave pointer for rx_handler
be2net: Bump up the version number
be2net: Copyright notice change. Update to Emulex instead of ServerEngines
e1000e: fix kconfig for crc32 dependency
netfilter ebtables: fix xt_AUDIT to work with ebtables
xen network backend driver
bonding: Improve syslog message at device creation time
bonding: Call netif_carrier_off after register_netdevice
bonding: Incorrect TX queue offset
net_sched: fix ip_tos2prio
xfrm: fix __xfrm_route_forward()
be2net: Fix UDP packet detected status in RX compl
Phonet: fix aligned-mode pipe socket buffer header reserve
netxen: support for GbE port settings
...
Fix up conflicts in drivers/staging/brcm80211/brcmsmac/wl_mac80211.c
with the staging updates.
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
