Increase concatenated buffer from 8K to 32K to get better performance.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Protect rx_tickets and rx_packets[] lists with spinlocks to fix the
race condition for concurrent list operations. In iwmc3200wifi both
sdio_isr_worker and rx_worker workqueues can access the rx ticket
and packets lists at the same time under high rx load.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add event tracer for iwmc3200wifi driver. When enabled, all the
commands and responses between the driver and firmware (also
including Tx/Rx frames) will be recorded in the ftrace ring buffer.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use list_for_each_entry instead of list_for_each_entry_safe in
places iteration against list entry removal is not required.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to make sure we don't associate with APs on unallowed
channels (according to regulatory setting). This could happen
when the channel is not specified (auto-select) within the
connection request. In this case we get the AP's channel until
the firmware indicates the association succeeded later. We need
to verify the associated channel. If the channel is disabled by
regulatory, we have to disassociate with the AP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check successful completion of BSM loading. Give a chance to
load BSM again. If BSM loading is unsuccessful we should exit
and not initilize NIC. Before this checking even if the BSM loading failed
driver tries to initilize the NIC which should not be the case.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
4965 hardware has 7 queues reserved and the
remaining ones used for aggregation, 5000
and higher need to have 10 reserved. This
is not very clear in the code right now,
unfortunately.
Introduce a new IWL_TX_FIFO_UNUSED constant
and make the queue/FIFO mapping arrays able
to hold that value, and change the setup
code to reserve all queues in the arrays
(the queue number is the index) and use the
new unused constant to not map those queues
to any FIFO.
Additionally, clear up the AC/queue mapping
code to be more understandable. The mapping
is the identity mapping right now, but with
the mapping function I think it's easier to
understand what happens there.
Finally, HCCA isn't implemented at all and
I think newer microcode removed it, so let's
remove all mention of it in the code, some
comments remain for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add internal short scan support for 3945 NIC, This allows 3945 NIC
to support radio reset request like the other series of NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
small change to remove unnecessary "ret" parameter since it not being
used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
"internal_scan" debugfs function serves the same propose of mode "0" of
"force_reset" debugfs function. Remove it to avoid duplicate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_apm_stop_master and iwl_internal_short_hw_scan
are only used within iwlcore and thus do not need to be exported.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For later station notification support we would like WEP key setting to be
done synchronously always. Currently all places from which WEP key is set
can sleep, but the usage of sta_lock prevents it to do so. Modify the
locking to use priv->mutex instead and thus enable this call to sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
small code cleanup to remove un-necessary parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
These files are incompatible with some changes
I'm making, and don't really belong into sysfs
anyway as they can only be used for debugging.
Since writing them will probably crash the
firmware, keep only the reading part and move
them into debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since rfkill integration, mac80211 can no
longer add an interface while the hardware
is not ready, so STATUS_MODE_PENDING can
never be set.
Also, remove another superfluous channel
sanity check and return the commit_rxon
return value in case it failed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This code will never trigger, because when
we call this during interface start, neither
priv->vif nor priv->iw_mode conditions will
be true, and when it happens during reset
then priv->vif is also NULL. Also, in both
cases the same code will be executed as part
of iwl_bss_info_changed(), which contains a
copy of this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Only used on 3945, so it can be in the
3945-specific part of the data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Not all queues are mapped for frame transmission,
so saying "AC" is misleading. They are all mapped
to FIFOs, obviously, though, so use that term and
also say AC/CMD instead of just AC for the queue
type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_mac_beacon_update can only be called
when the operating mode is IBSS, so it
doesn't need to verify that again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 will always enforce using a channel
that the driver allowed for IBSS use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This variable is assigned a default value,
but then assigned zero as soon as mac80211
calls a change channel (which will happen
right after the hw is started) and after
that it never changes again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
With some of the new code in mac80211, public action
frames can be exchanged as non-injected frames even
while not associated.
Aside from that, dropping frames here is pointless
since we do deal with arbitrary frames that were
injected already, so let mac80211 make the decision
about which frames to allow or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_mac_reset_tsf will only ever be called in
IBSS mode, so checking for other modes is not
useful and the code that depends on that will
not be executed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 will not allow using channels not
marked as allowing IBSS for IBSS mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Updating the variables last_rx_rssi, last_tsf
and last_beacon_time needs a lot of code but
they are not actually used in iwlagn (only in
3945) so we can move them to the 3945 specific
data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since the ICT data is all AGN specific, it can
be the first data to create the _agn part of the
device-specific union in the priv struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
To be obviously correct, this patch only modifies
3945 files and the struct definition. A follow-up
patch will create the AGN part of the union.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
All the ICT ISR code is iwlagn specific, and doesn't
need to be in iwlcore. So create a new iwl-agn.h
header file that will hold agn specific function
declarations etc., and move the ICT code into a new
iwl-agn-ict.c file that is linked into iwlagn. This
also gets rid of exporting those symbols.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The AR_IMR_S2 register sometimes cannot be read correctly. Instead of a
valid value, 0xdeadbeef is returned. The driver has been observed
writing that value back to AR_IMR_S2 after changing a few bits.
Cache the register value in ah->imrs2_reg and always write chached value
to the register.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the workaround limiting chipset TX power to 12dB, instead
using the value configured by the mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable host TX rate control. The wl1271 firmware is already managing rate
control, so this eliminate unnecessary host processing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of managing the TX security sequence number as two variables, use
one 64 bit variable. This greatly simplifies the handling of the number.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the required block count calculation. Though it
introduces a division operator, it greatly simplifies the formula.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses a higher precision timer to synchronize with the firmware
clock. Improved precision is needed as on some platforms a jiffy may be up to
tens of milliseconds, and the required precision is closer to TU's.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements looped IRQ handling. In essence, if a new interrupt is
asserted by the FW while the host is processing the previous one, the host
will directly proceed processing the new IRQ without leaving the handling
function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't mask firmware interrupts while processing interrupts. This allows the
interrupt handler looping to work efficiently thus reducing interrupt
processing latency.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will ack RX frames read from the firmware in one single write,
instead of acking all the frames separately. This will reduce the amount of
required communication per frame.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the annoying and dmesg-flooding WLAN PSM entry/exit traces. Instead,
only output them if PSM traces are enabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue stopping/waking functionality was broken in a way that could
cause huge latencies in TX transfers and even cause the TX to stall in the
right circumstances. Correct these problems.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ad-hoc mode preventing mac80211 from properly
detecting other ad-hoc networks with the same SSID.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Fix a TX result overflow problem that was present in the TX path and visible
with at least linksys AP's (probably any AP with high throughput capability.)
- Optimize TX by writing FW trigger for a group of TX frames instead of
each and every frame.
- Slightly optimize the TX path code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most probably patch "wl1271: add most of the normal initialization commands
to PLT mode" enabled the RX path in firmware so that now driver received
frames and passed them to mac80211, which warned about them.
Workaround this by not retrieving frames from the hardware, just ignore them.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed two bugs causing problems when unloding wl1271 module. First was
missing sdio_set_drvdata call from the probe function, second was order
of function calls in the remove function.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed access to fw status register to use raw read instead of
translated addressing. On SDIO access by translated addressing was not
working and raw access is working also on SPI.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added initial implementation of SDIO interfacte to the wl1271 driver.
When selected, this adds new module called "wl1271_sdio".
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Divided wl1271 driver to wl1271 "core" and wl1271_spi modules in preparation
of integration of the SDIO implementation.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed wl1271_spi.h header as there's no more need to access functions
declared there outside of wl1271_spi.c. Also made those SPI access
functions static.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed the driver to use if_ops structure to abstract access to the IO
layer (SPI or SDIO).
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved wl1271 drivers probe, remove etc. functions and structres to
wl1271_spi.c from wl1271_main.c in preparation of implementing SDIO interface.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
P54 devices always generate a full tx_status report
(ACK, PSM, rate control, etc..) for every xmitted frame.
Therefore, I think The driver qualifies for the
REPORTS_TX_ACK_STATUS hardware feature flag.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_hw_register_timeout() was duplicated between phy.c and reset.c.
Since it is too big and too much used to be an inline function, move it
away from the ath5k.h header into reset.c. Remove _ATH5K_RESET and
_ATH5K_PHY defines.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust formatting of the affected lines to satisfy checkpatch.pl.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all unnecessary function declarations from ath5k.h. Comment out
unused functions. Remove ath5k_hw_get_tsf32(), which is too trivial to
be commented out. Make functions static if suggested by sparse. Make
ath5k_pm_ops static.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export rt2x00soc_probe from rt2x00soc as it is used in rt2800pci.
Otherwise loading rt2800pci gives "rt2800pci: Unknown symbol
rt2x00soc_probe".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the wireless summit in Portland we discussed a way of
loading firmware asynchronously from ->probe() before
registration to mac80211, in order to register with the
wireless subsystems with complete information in cases
where firmware is required to know parameters.
This is not yet the case in iwlwifi, but for some new
features we're working on it will be the case since
those will only be supported by new firmware images.
Hence, to start with, convert iwlwifi to load firmware
asynchronously from probe, unbinding the device when
firmware loading fails, and only registering with the
wireless subsystems after firmware has been loaded
successfully.
Future patches will hook into this to register the
new firmware capabilities, depending on the firmware
API version.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ar9170 to load firmware asynchronously
out of ->probe() and only register with mac80211 when
all firmware has been loaded successfully. If, on the
other hand, any firmware fails to load, it will now
unbind from the device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Compiling rt2800pci with CONFIG_RT2800PCI_SOC fails with "... rt2880pci.c:
error: incompatible type for argument 2 of 'rt2x00soc_probe'".
Fix this by using &rt2800pci_ops instead of rt2800pci_ops.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for CEIVA USB wireless adapters to the rt73usb driver.
Signed-off-by: Bryan Polk <sainth@eidolons.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first chunk fixes a debugging assert to print a warning about array underflows.
The second chunk corrects a potential array underflow. I also removed an assert
in the second chunk because it can no longer happen.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even if keylen == 0 is a bug and should not really happen, better avoid
possibility of passing bad value to firmware.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is no longer needed. I missed to remove this in
567ec874d1 ("net: convert multiple
drivers to use netdev_for_each_mc_addr, part6")
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tx/mcc polling, napi_complete() is being incorrectly called
before reaping tx completions. This can cause tx compl processing
to be scheduled on another cpu concurrently which can result in a panic.
This if fixed by calling napi complete() after tx/mcc compl processing
but before re-enabling interrupts (via a cq notify).
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sis190 devices don't report LinkChange, so do polling for
link status.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11926
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Resending with the proper subject. Sorry for the mess. ]
This patch is based on the RFC of Stanislaw Gruszka.
More specifically it fixes two possible races:
- One, described by Stanislaw, may lead to permanent disabling of the Tx
queue.
This is fixed by adding the smp_wmb() to propagate the BD consumer
change towards the memory.
- Second may lead to bnx2x_start_xmit() returning NETDEV_TX_BUSY.
This is fixed by taking a tx_lock() before rechecking the number of
available Tx BDs.
thanks,
vlad
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-pci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Enable NMI on all cpus on UV
vgaarb: Add user selectability of the number of GPUS in a system
vgaarb: Fix VGA arbiter to accept PCI domains other than 0
x86, uv: Update UV arch to target Legacy VGA I/O correctly.
pci: Update pci_set_vga_state() to call arch functions
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Enable L3 CID only on AMD
x86, cacheinfo: Remove NUMA dependency, fix for AMD Fam10h rev D1
x86, cpu: Print AMD virtualization features in /proc/cpuinfo
x86, cacheinfo: Calculate L3 indices
x86, cacheinfo: Add cache index disable sysfs attrs only to L3 caches
x86, cacheinfo: Fix disabling of L3 cache indices
intel-agp: Switch to wbinvd_on_all_cpus
x86, lib: Add wbinvd smp helpers
guest to remote communication with vhost net sometimes stops until
guest driver is restarted. This happens when we get guest kick precisely
when the backend send queue is full, as a result handle_tx() returns without
polling backend. This patch fixes this by restarting tx poll on this condition.
Signed-off-by: Sridhar Samudrala <samudrala@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Tom Lendacky <toml@us.ibm.com>
get_user_pages_fast returns number of pages on success, negative value
on failure, but never 0. Fix vhost code to match this logic.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vq log eventfd context pointer needs to be initialized, otherwise
operation may fail or oops if log is enabled but log eventfd not set by
userspace. When log_ctx for device is created, it is copied to the vq.
This reset was missing.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost was dong some complex math to get
offset to log at, and got it wrong by a couple of bytes,
while in fact it's simple: get address where we write,
subtract start of buffer, add log base.
Do it this way.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Apparently bogus mc address can break IPOIB multicast processing. Therefore
returning the check for addrlen back until this is resolved in bonding (I don't
see any other point from where mc address with non-dev->addr_len length can came
from).
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the VPD searching code is abstracted away, the outer loop used
to detect the read-only large resource data type section is useless.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the VPD searching code is abstracted away, the outer loop used
to detect the read-only large resource data type section is useless.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_info_keyword() helper function to
find information field keywords within read-only and read-write large
resource data type sections.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a preprocessor constant to describe the PCI VPD
information field header size and an inline function to extract the
size of the information field itself.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_tag() helper function to find VPD
resource data types in a buffer.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces more VPD preprocessor definitions to identify some
small and large resource data type item names. The patch then continues
to correct how the tg3 and bnx2 drivers search for the "read-only data"
large resource data type.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a preprocessor constant to describe the PCI VPD large
resource data type tag size and an inline function to extract the large
resource section size from the large resource data type tag.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (88 commits)
powerpc: Fix lwsync feature fixup vs. modules on 64-bit
powerpc: Convert pmc_owner_lock to raw_spinlock
powerpc: Convert die.lock to raw_spinlock
powerpc: Convert tlbivax_lock to raw_spinlock
powerpc: Convert mpic locks to raw_spinlock
powerpc: Convert pmac_pic_lock to raw_spinlock
powerpc: Convert big_irq_lock to raw_spinlock
powerpc: Convert feature_lock to raw_spinlock
powerpc: Convert i8259_lock to raw_spinlock
powerpc: Convert beat_htab_lock to raw_spinlock
powerpc: Convert confirm_error_lock to raw_spinlock
powerpc: Convert ipic_lock to raw_spinlock
powerpc: Convert native_tlbie_lock to raw_spinlock
powerpc: Convert beatic_irq_mask_lock to raw_spinlock
powerpc: Convert nv_lock to raw_spinlock
powerpc: Convert context_lock to raw_spinlock
powerpc/85xx: Add NOR, LEDs and PIB support for MPC8568E-MDS boards
powerpc/86xx: Enable VME driver on the GE SBC610
powerpc/86xx: Enable VME driver on the GE PPC9A
powerpc/86xx: Add MSI section to GE PPC9A DTS
...
Lots of changes. Remove volatile keywords. Take the advice in the comments
and change video_slot to slot_addr. Factor out fifteen or so "channel >>
8" shifts into three shifts higher up the call graph. Make
csc_setpalette() atomic, pass the correct color values. Check for
ioremap() failure. Add missing break statement, thus fixing 24 bit console
visual (blue background bug). Remove some uninformative printk() noise.
Add a description for powerbook 140/170 graphics.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cleanup whitespace and code style. Remove unused #includes and prototypes.
Remove obsolete, redundant or misleading comments. Remove dead code and
redundant initialisers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add the missing mac video modes for the Portrait and 12" RGB displays. The
specs come from the Mac LC III developer note.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The valkyriefb driver needs the CUDA to work in order to set the video
mode at boot. So initialise the device earlier, and bring the m68k code
closer to the powermac code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Valkyriefb and macfb will adopt the same card if they get the chance, so
remove valkyrie support from macfb. Also fix the "valkyriefb: can't do
832x624x8" problem reported by Raylynn Knight some time ago, by adding
vmode 13 support for CONFIG_MAC. Also add vmode 11 since that works too.
Make use of the monitor sense lines on 68k Macs too. Also some cleanups.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The valkyriefb driver assumes that this logic holds:
mac_vmode_to_var(X, cmode, &var);
mac_var_to_vmode(&var, &vmode, &cmode);
assert(vmode == X);
But it doesn't hold because mac_var_to_vmode() can return a mode with a
slower pixel clock, even when a match is available. So we end up with this
failure:
using video mode 11 and color mode 0.
valkyriefb: vmode 12 not valid.
valkyriefb: can't set default video mode
valkyriefb: vmode 12 not valid.
Rather than have mac_var_to_mode() return the first reasonable mode it
finds, have it return the mode that is closest to the requested one (or
the mode with the closest longer pixel clock period if there is no exact
match).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move platform device code from the drivers to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move platform device code from the driver to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add platform driver support to the pmac-zilog driver, for m68k macs.
Place the powermac-specific code inside #ifdef CONFIG_PPC_PMAC.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Adjust the platform device code to conform with the code style used in the
rest of this patch series. No need to name resources nor to register
devices which are not applicable.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Trivial patch which adds the __init macro to the module_init
function and all of its helper functions of drivers/char/vme_scc.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The debugfs support of the Marvell driver is buggy. It is limited to one
controller per system. Fix this by using the controller specific debugfs
directory as parent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make bcm203x_table also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of btmrvl_sdio.c driver.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On Alchemy the PCMCIA area lies at the end of the chips 36bit system bus
area. Currently, addresses at the far end of the 32bit area are assumed
to belong to the PCMCIA area and fixed up to the real 36bit address before
being passed to ioremap().
A previous commit enabled 64 bit physical size for the resource datatype on
Alchemy and this allows to use the correct 36bit addresses when registering
the PCMCIA sockets.
This patch removes the 32-to-36bit address fixup and registers the Alchemy
demo board pcmcia socket with the correct 36bit physical addresses.
Tested on DB1200, with a CF card (ide-cs driver) and a 3c589 PCMCIA ethernet
card.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/994/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we wait for the once-per-second cleanup to free transmit SKBs,
sockets with small transmit buffer sizes might spend most of their
time blocked waiting for the cleanup.
Normally we do a cleanup for each transmitted packet. We add a
watchdog type timer so that we also schedule a timeout for 150uS after
a packet is transmitted. The watchdog is reset for each transmitted
packet, so for high packet rates, it never expires. At these high
rates, the cleanups are done for each packet so the extra watchdog
initiated cleanups are neither needed nor triggered.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: netdev@vger.kernel.org
To: gregkh@suse.de
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/968/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This version has spelling and comment changes based on feedback from
Eric Dumazet.
Although the hardware supports a 4/8bit SD interface and the driver
unconditionally advertises all hardware caps to the MMC core, not all
datalines may actually be wired up. This patch introduces another
field to au1xmmc platform data allowing platforms to disable certain
advanced host controller features.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: linux-mmc@vger.kernel.org
CC: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes the ar7 clock code implement the Linux clk API. Drivers
using the various clocks available in the SoC are updated accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
To: linux-mips@linux-mips.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: netdev@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Octeon ethernet hardware can handle NETIF_F_SG, so we enable it.
A gather list of up to six fragments will fit in the SKB's CB
structure, so no extra memory is required. If a SKB has more than six
fragments, we must linearize it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the driver to be a reasonably well behaved NAPI citizen.
There is one NAPI instance per CPU shared between all input ports. As
receive backlog increases, NAPI is scheduled on additional CPUs.
Receive buffer refill code factored out so it can also be called from
the periodic timer. This is needed to recover from temporary buffer
starvation conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/839/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Stop the queue if too many packets are queued. Restart it from a high
resolution timer.
Rearrange and simplify locking and SKB freeing code
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/843/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After aligning the blocks returned by kmalloc, we need to save the original
pointer so they can be correctly freed.
There are no guarantees about the alignment of SKB data, so we need to
handle worst case alignment.
Since right shifts over subtraction have no distributive property, we need
to fix the back pointer calculation.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts the au1000-eth driver to become a full platform-driver
as it ought to be. We now pass PHY-speficic configurations through
platform_data but for compatibility the driver still assumes the default
settings (search for PHY1 on MAC0) when no platform_data is passed. Tested
on my MTX-1 board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/619/
Patchwork: http://patchwork.linux-mips.org/patch/963/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the devboard NOR MTD mapping driver with physmap-flash support.
Also honor the "swapboot" switch settings wrt. to the layout of the
NOR partitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Limit the amount of address space claimed for Alchemy serial ports to
0x1000. On the Au1300, ports are only 0x1000 apart, and the registers
only extend to 0x110 at most on all supported alchemy models.
On the Au1300 the autodetect logic no longer works and this makes it
necessary to specify the port type through platform data. Because of
this the MSR quirk needs to be moved outside the autoconfig() function
which will no longer be called when UPF_FIXED_TYPE is specified.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
- supports Db1000, DB/PB1100/1500/1550/1200.
- support for carddetect and statuschange IRQs.
- pcmcia socket mem/io/attr areas and irqs passed through
platform resource information.
- doesn't freeze system during card insertion/ejection like
the one it replaces.
- boardtype is automatically detected using BCSR ID register.
Run-tested on the DB1200.
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move TC_PRIO_CONTROL check and queue remapping into
ixgbe_select_queue(). Remapping queues after the qdisc
can result in the wrong qdisc queue being stopped with
netif_stop_subqueue(). Even if this is resolved and the
correct queue is stopped it can result in a queue being
blocked by TC_PRIO_CONTROL frames uneccesarily. Moving
this into the select_queue routine maintains alignment
between tx_rings and qdisc queues.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the register_netdevice() call fails, the newly allocated device is
not freed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e8469ed959c373c2ff9e6f488aa5a14971aebe1f
Author: Patrick McHardy <kaber@trash.net>
Date: Tue Feb 23 20:41:30 2010 +0100
Support specifying the initial device flags when creating a device though
rtnl_link. Devices allocated by rtnl_create_link() are marked as INITIALIZING
in order to surpress netlink registration notifications. To complete setup,
rtnl_configure_link() must be called, which performs the device flag changes
and invokes the deferred notifiers if everything went well.
Two examples:
# add macvlan to eth0
#
$ ip link add link eth0 up allmulticast on type macvlan
[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
link/ether 26:f8:84:02:f9:2a brd ff:ff:ff:ff:ff:ff
[ROUTE]ff00::/8 dev macvlan0 table local metric 256 mtu 1500 advmss 1440 hoplimit 0
[ROUTE]fe80::/64 dev macvlan0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0
[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500
link/ether 26:f8:84:02:f9:2a
[ADDR]11: macvlan0 inet6 fe80::24f8:84ff:fe02:f92a/64 scope link
valid_lft forever preferred_lft forever
[ROUTE]local fe80::24f8:84ff:fe02:f92a via :: dev lo table local proto none metric 0 mtu 16436 advmss 16376 hoplimit 0
[ROUTE]default via fe80::215:e9ff:fef0:10f8 dev macvlan0 proto kernel metric 1024 mtu 1500 advmss 1440 hoplimit 0
[NEIGH]fe80::215:e9ff:fef0:10f8 dev macvlan0 lladdr 00:15:e9:f0:10:f8 router STALE
[ROUTE]2001:6f8:974::/64 dev macvlan0 proto kernel metric 256 expires 0sec mtu 1500 advmss 1440 hoplimit 0
[PREFIX]prefix 2001:6f8:974::/64 dev macvlan0 onlink autoconf valid 14400 preferred 131084
[ADDR]11: macvlan0 inet6 2001:6f8:974:0:24f8:84ff:fe02:f92a/64 scope global dynamic
valid_lft 86399sec preferred_lft 14399sec
# add VLAN to eth1, eth1 is down
#
$ ip link add link eth1 up type vlan id 1000
RTNETLINK answers: Network is down
<no events>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC5121 FEC requeries 4-byte alignmnent for TX data buffers.
This patch is a work around that copies misaligned tx packets
to an aligned skb before sending.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the fs_enet driver to support MPC512x FEC.
Enable it with CONFIG_FS_ENET_MPC5121_FEC option.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
toshiba_acpi: Add full hotkey support
hp-wmi: Add support for tablet rotation key
dell-laptop: Add another Dell laptop to the DMI whitelist
classmate-laptop: use a single MODULE_DEVICE_TABLE to get correct aliases
dell-laptop: Pay attention to which devices the hardware switch controls
dell-laptop: Use buffer with 32-bit physical address
dell-laptop: Blacklist machines not supporting dell-laptop
dell-laptop: Block software state changes when rfkill hard blocked
dell-laptop: Fix small memory leak
dell-laptop: Fix platform device unregistration
dell-laptop: Update rfkill state on kill switch
compal-laptop: Replace sysfs support with rfkill support
compal-laptop: Add support for known Compal made Dell laptops
MAINTAINERS: update drivers/platform/x86 information
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (362 commits)
V4L-DVB: cx88-dvb: remove extra attribution for core
V4L/DVB: v4l: soc_camera: fix bound checking of mbus_fmt[] index
V4L/DVB: Add support for SMT7020 to cx88
V4L/DVB: radio-si470x: Use UTF-8 encoding on a comment
V4L/DVB: MAINTAINERS: Telegent tlg2300 section fix
V4L/DVB: gspca_stv06xx: Add support for camera button
V4L/DVB: gspca_ov519: add support for the button on ov511 based cams
V4L/DVB: gspca_ov519: Add support for the button on ov518 based cams
V4L/DVB: gspca_ov519: add support for the button on ov519 based cams
V4L/DVB: gspca_main: Fix a compile error when CONFIG_INPUT is not set
V4L/DVB: gspca_main: some input error handling fixes
V4L/DVB: gspca_main: Allow use of input device creation code for non int. inputs
V4L/DVB: gspca_pac7302: much improved exposure control
V4L/DVB: gspca_sonixb: Make sonixb driver handle pas106 and pas202 cameras
V4L/DVB: gspca_sonixb: pas106: fixup bright ctrl and add gain and exposure ctrls
V4L/DVB: Documentation: gspca.txt: update known mr97310a cams
V4L/DVB: gspca_mr97310a: add support for the Sakar 1638x CyberPix
V4L/DVB: gscpa_sonixb: limit ov7630 max framerate at 640x480
V4L/DVB: gspca_sonixb: pas202: fixup brightness ctrl and add gain and exposure ctrls
V4L/DVB: gscpa_sonixb: Differentiate between sensors with a coarse and fine expo ctrl
...
ULE (Unidirectional Lightweight Encapsulation RFC 4326) decapsulation
has a bug that causes endless loop when Payload Pointer of MPEG2-TS
frame is 182 or 183. Anyone who sends malicious MPEG2-TS frame will
cause the receiver of ULE SNDU to go into endless loop.
This patch was generated and tested against linux-2.6.32.9 and should
apply cleanly to linux-2.6.33 as well because there was only one typo
fix to dvb_net.c since v2.6.32.
This bug was brought to you by modern day Santa Claus who decided to
shower the satellite dish at Keio University with heavy snow causing
huge burst of errors. We, receiver end, received Santa Claus's gift in
the form of kernel bug.
Care has been taken not to introduce more bug by fixing this bug, but
please scrutinize the code for I always produces buggy code.
Signed-off-by: Ang Way Chuang <wcang79@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
sh: remove dead LED code for migo-r and ms7724se
sh: ecovec build fix for CONFIG_I2C=n
sh: ecovec r-standby support
sh: ms7724se r-standby support
sh: SH-Mobile R-standby register save/restore
clocksource: Fix up a registration/IRQ race in the sh drivers.
sh: ms7724: modify scan_timing for KEYSC
sh: ms7724: Add sh_sir support
sh: mach-ecovec24: Add sh_sir support
sh: wire up SET/GET_UNALIGN_CTL.
sh: allow alignment fault mode to be configured at kernel boot.
sh: sh7724: Update FSI/SPU2 clock
sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
sh: add sh7724 kick callback to clk_div4_table
sh: introduce struct clk_div4_table
sh: clock-cpg div4 set_rate() shift fix
sh: Turn on speculative return for SH7785 and SH7786
sh: Merge legacy and dynamic PMB modes.
sh: Use uncached I/O helpers in PMB setup.
sh: Provide uncached I/O helpers.
...
This makes the b43 driver just automatically fall back to PIO mode when
DMA doesn't work.
The driver already told the user to do it, so rather than have the user
reload the module with a new flag, just make the driver do it
automatically. We keep the message as an indication that something is
wrong, but now just automatically fall back to the hopefully working PIO
case.
(Some post-2.6.33 merge fixups by Larry Finger <Larry.Finger@lwfinger.net>
and yours truly... -- JWL)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While ath9k does not support RIFS yet, the ability to receive RIFS
frames is currently enabled for most chipsets in the initvals.
This is causing baseband related issues on AR9160 and AR9130 based
chipsets, which can lock up under certain conditions.
This patch fixes these issues by overriding the initvals, effectively
disabling RIFS for all affected chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch the prefix registers of all online CPUs are stored in the
the zcore dump header. This allows dump analysis tools to access the register
information that is stored in the prefix pages without using the System.map.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Flushing the dasd ccw request queue may stop the processing of the
block device request queue. Destroy partitions may wait for
outstanding requests and thus hang.
Swapping dasd_destroy_partitions and dasd_flush_request_queue so that
the request queue is empty before dasd_destroy_partitions is called.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The function dasd_device_from_cdev returns a reference to the dasd
device and increases the refcount by one. If an exception occurs,
the refcount was not decreased in all cases
e.g. in dasd_discipline_show.
Prevent the offline processing from hang by correcting two functions
to decrease the refcount even if an error occured.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setting a DASD online and offline in quick succession may cause
a kernel panic or let the chhccwdev command wait forever.
The Online process is split into two parts. After the first part
is finished the offline process may be called. This may result
in a situation where the second online processing part tries to
set the DASD offline as well.
Use a mutex to protect online and offline against each other.
Also correct some checking.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use asm offsets to make sure the offset defines to struct _lowcore and
its layout don't get out of sync.
Also add a BUILD_BUG_ON() which checks that the size of the structure
is sane.
And while being at it change those sites which use odd casts to access
the current lowcore. These should use S390_lowcore instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the MACHINE_IS_LPAR flag for code that should only be
executed if Linux is running in an LPAR.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove a memset hack that relied on the internal layout of the
qdio_irq struct and move the per device statistics data into an own
cache line to avoid cache line bashing between the inbound and the
outbound queue tasklets. Also reduce the number of allocated queues
from 32 to 4 which is the current maximum. That saves a cache line
in struct qdio_irq.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add counters for the number of processed SBALs. The numbers summarize
how many SBALs were processed at each queue scan and indicate the
utilization of the queue. Furthermore the number of unsuccessfull
queue scans, SBAL errors and the total number of processed
SBALs are accounted.
Also regroup struct qdio_q to move read-mostly and write-mostly data
into different cachelines.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove support to be able to dump 31 bit systems with a 64 bit dumper.
This is mostly useless since no distro ships 31 bit kernels together
with a 64 bit dumper.
We also get rid of a bit of hacky code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some parts of cio do not shift PAGE_DEFAULT_KEY correctly and end up
with an incorrect key in their data structures.
Since the default key is zero this doesn't really matter. However if
somebody would use key-controlled protection for debugging purposes
it would be quite helpful if all of this would work as expected.
Also remove a stale declaration.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ccw_device_pm_restore: trigger subchannel event to better handle
changes to the subchannel device.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Callers of ccw_device_notify could not distinguish between a driver
who has no notifier registered and a driver who doesn't want to keep
a device after a certain event. Change this by adding proper return
codes.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the potentially long blocking wait_event's used by the cio
settle mechanism interruptible.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To fetch a pending channel report word (crw) we use a kernel
thread which triggers stcrw and sleeps on a semaphore. The s390
machine check handler uses crw_handle_channel_report to handle
one crw if needed.
This patch replaces the semaphore with a waitqueue (to block the
kernel thread) and an atomic_t (to count the number of pending
requests).
By this we achieve the ability to force this thread to check for
a pending crw (independent on when it is triggered by the machine
check handler) and wait for this action to finish.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces a proc file cio_settle. A write request to
this file is blocked until all queued cio actions are handled.
This will allow userspace to wait for pending work affecting
device availability after changing cio_ignore or the hardware
configuration.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We used to maintain 2 singlethreaded workqueues for synchronization
and to trigger work from interrupt context. Since our latest cio
changes we only use one of these workqueues. So get rid of the
unused workqueue, rename the remaining one to "cio_work_q" and move
its ownership to the channel subsystem driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert netmask to __be32 and format it with %pI4
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Konrad Rzeszutek <ketuzsezr@darnok.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The ISA skeleton net driver has been obsolete and unmaintained for many
years. Any hardware remotely like ISA will use the platform API and
look much more like a PCI driver, and make much better use of netdev
APIs such as NAPI.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set power.async_suspend for all SCSI devices, targets and hosts, so
that they can be suspended and resumed in parallel with the main
suspend/resume thread and possibly with other devices they don't
depend on in a known way (i.e. devices which are not their parents or
children).
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1331) adds non-tree ordering constraints needed for
proper resume of PCI USB host controllers from hibernation. The main
issue is that non-high-speed devices must not be resumed before the
high-speed root hub, because it is the ehci_bus_resume() routine which
takes care of handing the device connection over to the companion
controller. If the device resume is attempted before the handover
then the device won't be found and it will be treated as though it had
disconnected.
The patch adds a new field to the usb_bus structure; for each
full/low-speed bus this field will contain a pointer to the companion
high-speed bus (if one exists). It is used during normal device
resume; if the hs_companion pointer isn't NULL then we wait for the
root-hub device on the hs_companion bus.
A secondary issue is that an EHCI controlller shouldn't be resumed
before any of its companions. On some machines I have observed
handovers failing if the companion controller is reinitialized after
the handover. Thus, the EHCI resume routine must wait for the
companion controllers to be resumed.
The patch also fixes a small bug in usb_hcd_pci_probe(); an error path
jumps to the wrong label, causing a memory leak.
[rjw: Fixed compilation for CONFIG_PM_SLEEP unset.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).
This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There are some dependencies between devices (in particular, between
EHCI USB controllers and their OHCI/UHCI siblings) which are not
reflected by the structure of the device tree. With synchronous
suspend and resume these dependencies are taken into accout
automatically, because the devices in question are always registered
in the right order, but to meet these constraints with asynchronous
suspend and resume the drivers of these devices will need to use
dpm_wait() in their suspend/resume routines, so introduce a helper
function allowing them to do that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It has been shown by testing that total device resume time can be
reduced significantly (by as much as 50% or more) if the async
threads executing some devices' resume routines are all started
before the main resume thread starts to handle the "synchronous"
devices.
This is a consequence of the fact that the slowest devices tend to be
located at the end of dpm_list, so their resume routines are started
very late. Consequently, they have to wait for all the preceding
"synchronous" devices before their resume routines can be started
by the main resume thread, even if they are "asynchronous". By
starting their async threads upfront we effectively move those
devices towards the beginning of dpm_list, without breaking their
ordering with respect to their parents and children. As a result,
their resume routines are started much earlier and we are able to
save much more device resume time this way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add configuration switch CONFIG_PM_ADVANCED_DEBUG for compiling in
extra PM debugging/testing code allowing one to access some
PM-related attributes of devices from the user space via sysfs.
If CONFIG_PM_ADVANCED_DEBUG is set, add sysfs attribute power/async
for every device allowing the user space to access the device's
power.async_suspend flag and modify it, if desired.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add sysfs attribute /sys/power/pm_async allowing the user space to
disable/enable asynchronous suspend/resume of devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Theoretically, the total time of system sleep transitions (suspend
to RAM, hibernation) can be reduced by running suspend and resume
callbacks of device drivers in parallel with each other. However,
there are dependencies between devices such that we're not allowed
to suspend the parent of a device before suspending the device
itself. Analogously, we're not allowed to resume a device before
resuming its parent.
The most straightforward way to take these dependencies into accout
is to start the async threads used for suspending and resuming
devices at the core level, so that async_schedule() is called for
each suspend and resume callback supposed to be executed
asynchronously.
For this purpose, introduce a new device flag, power.async_suspend,
used to mark the devices whose suspend and resume callbacks are to be
executed asynchronously (ie. in parallel with the main suspend/resume
thread and possibly in parallel with each other) and helper function
device_enable_async_suspend() allowing one to set power.async_suspend
for given device (power.async_suspend is unset by default for all
devices). For each device with the power.async_suspend flag set the
PM core will use async_schedule() to execute its suspend and resume
callbacks.
The async threads started for different devices as a result of
calling async_schedule() are synchronized with each other and with
the main suspend/resume thread with the help of completions, in the
following way:
(1) There is a completion, power.completion, for each device object.
(2) Each device's completion is reset before calling async_schedule()
for the device or, in the case of devices with the
power.async_suspend flags unset, before executing the device's
suspend and resume callbacks.
(3) During suspend, right before running the bus type, device type
and device class suspend callbacks for the device, the PM core
waits for the completions of all the device's children to be
completed.
(4) During resume, right before running the bus type, device type and
device class resume callbacks for the device, the PM core waits
for the completion of the device's parent to be completed.
(5) The PM core completes power.completion for each device right
after the bus type, device type and device class suspend (or
resume) callbacks executed for the device have returned.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add new device sysfs attribute, power/control, allowing the user
space to block the run-time power management of the devices. If this
attribute is set to "on", the driver of the device won't be able to power
manage it at run time (without breaking the rules) and the device will
always be in the full power state (except when the entire system goes
into a sleep state).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
This is not needed, since the function already do it. Also, it causes
a warning at the compilation, since a new var is declared in the middle
of the code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (48 commits)
x86/PCI: Prevent mmconfig memory corruption
ACPI: Use GPE reference counting to support shared GPEs
x86/PCI: use host bridge _CRS info by default on 2008 and newer machines
PCI: augment bus resource table with a list
PCI: add pci_bus_for_each_resource(), remove direct bus->resource[] refs
PCI: read bridge windows before filling in subtractive decode resources
PCI: split up pci_read_bridge_bases()
PCIe PME: use pci_pcie_cap()
PCI PM: Run-time callbacks for PCI bus type
PCIe PME: use pci_is_pcie()
PCI / ACPI / PM: Platform support for PCI PME wake-up
ACPI / ACPICA: Multiple system notify handlers per device
ACPI / PM: Add more run-time wake-up fields
ACPI: Use GPE reference counting to support shared GPEs
PCI PM: Make it possible to force using INTx for PCIe PME signaling
PCI PM: PCIe PME root port service driver
PCI PM: Add function for checking PME status of devices
PCI: mark is_pcie obsolete
PCI: set PCI_PREF_RANGE_TYPE_64 in pci_bridge_check_ranges
PCI: pciehp: second try to get big range for pcie devices
...
This patch adds support for the built-in dvb device
of a Samsung SMT7020s (x86 based STB) to the cx88 family.
Signed-off-by: Dirk Herrendoerfer <d.herrendoerfer@herrendoerfer.name>
Signed-off-by: Helmut Auer <helmut@helmutauer.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cosmetic patch corrects a wrong unicode "micro" character in a comment.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only tested with an stv6422 based cam, as that is the only stv06xx cam
I have with a button.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to hardware limitations this only works while the camera is
streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to hardware limitations this only works while the camera is
streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note due to hardware limitiations (no interrupt endpoint), this only works
when the camera is streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_main: Fix a compile error when CONFIG_INPUT is not set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2 small changes to input device error handling:
1) Make it fatal when we fail to create an input device (it is either this
or add checks for gspca_dev->input_dev being NULL in a lot of places)
2) Since we allow gspca_input_create_urb() to fail everywhere we call it,
and thus never check its return value, make it void.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow use of the gspca core input device creation code by subdrivers which
have non interrupt driven camera buttons.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My experience with fixing up the controls for the PAS sensors in
sonixb, has lead me to re-investigate the exposure control for the
pac7302. I've now found a regular exposure register in register bank 3
(which seems to be the sensor registers bank), and with this added a proper
fine grained exposure control. This patch also updates the do_autogain
function to work properly with this new finer grained control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the sonixb driver handle pas106 and pas202 cameras, when both it
and the sn9c102 driver are enabled in the kernel configuration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixup brightness ctrl and add gain and exposure ctrls for PAS106B sensors,
this allows enabling autogain (done), and makes the cam usable in low light
conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This camera has a sensor type we did not support sofar, this patch adds
support for the new sensor type found in the Sakar 1638x CyberPix.
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In 640x480, if the reg11 has less than 4, the image is
unstable (the bridge goes into a higher compression mode
which we have not reverse engineered yet).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixup brightness ctrl and add gain and exposure ctrls for PAS202BCB sensors,
this allows enabling autogain (done), and makes the cam usable in low light
conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some sensors only allow controlling the exposure by changing the clockdiv,
which means that exposure takes pretty large jumps (for example when going
from a div of 1 to 2, the exposure doubles). Use 2 different entries in
the controls array for these 2 different types of exposure (always
disabling one), and;
Add a new autogain algorithm for the coarse exposure case, which normally
changes the gain setting, only touching the exposure setting if the desired
luminance cannot be reached with gain, and after an exposure change once more
first tries gain, etc. Thus avoiding exposure changes, and the resulting
oscilation because of the huge steps these exposure controls take.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Leave bridge gain at 1.0 when we have a sensor gain, while at it also
change the bridge gain setting code to write both registers in one go
saving us a usb transaction.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixb: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gscpa_zc3xx: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gscpa_pac7311: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gscpa_pac207: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplify sensor detection a bit (share more of the code between cif and vga
cameras). Also remove an unnecessary write from zero_the_pointer().
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on experiments by Eric Wescott, edit the Sony GigaPocket (Kikyou)
card entry video and audio mux settings.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a slightly modified version of Eric Anderson's original patch
for the Sony Giga Pocket board. It has been updated to apply to the
latest ivtv driver version by Hans Verkuil <hverkuil@xs4all.nl> and
Andy Walls <awalls@radix.net>. Also Andy Walls modified the patch to
use a new Sony BTF-Pnx01Z tuner entry based on Eric Anderson's experimental
findings for the bandswitch.
>From Eric Anderson's original email:
1. The tuner on the card doesn't seem to match any standard
ones. I modified an existing tuner entry. Ideally a new tuner
entry should be created. (The only difference from the one I
modified is that the low-to-mid range frequency cut-off is
slightly different, as are the bit config settings.)
2. It wasn't obvious how to choose a second audio input other
than using "radio" as an option. Basically there's two GPIO
audio inputs. Using radio allowed me to avoid major restructuring
to the code. (perhaps other cards don't have this often...)
3. It's not clear that there's a mute setting that works. Not
sure why.
4. I haven't had a chance to test the two Svideo inputs. I set
them to COMPOSITE1 and SVIDEO2, but I'm not sure those are the
correct settings. The standard composite video inputs seem to work.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sony makes custome tuners for its GigaPocket line of ivtv based capture
cards. This adds an entry to the tuner-types list for such tuners.
Parameters are based on experiments by Eric Anderson <rico99@sbcglobal.net>.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ivtv_api_get_data() was performing more PCI MMIO than needed, resulting
often in it accounting for more than half the total time spent in
ivtv_irq_handler(). Now it only reads at most 7 of the 16 mailbox data words
over the PCI bus, and in some instances only 2 or 3 data words as needed.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enhancements to support DM365 ISP5 and VPSS module configuration.
Also cleaned up the driver by removing redundant variables.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the source file for ISIF driver on DM365. ISIF driver is equivalent
to CCDC driver on DM355 and DM644x. This driver is tested for YUV capture from
TVP514x driver. This patch contains the header files required for this driver.
Reviewed-by: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the header file for ISIF driver on DM365. ISIF driver is equivalent
to CCDC driver on DM355 and DM644x. This driver is tested for
YUV capture from TVP514x driver. This patch contains the header files required
for this driver.
Reviewed-by: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We know that the 300msec settling time after starting the digitizer is
only really needed when the digitizer is a SAA7115. So if we're not
using a SAA7115, skip the delay.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After implementing a 300msec wait between digitizer start and encoder
start, it has been determined that we don't need to wait quite as long
before configuring the encoder. This reduces the wait period from
100msec back to 50msec.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Martin Dauskardt <martin.dauskardt@gmx.de> has determined that the
encoder has a much better chance of starting cleanly if we
deliberately hold off starting it util the video digitizer has had a
chance to run for at least 300msec first. These changes implement an
enforced 300msec wait in the state machine that orchestrates streaming
start / stop.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the saa7111 driver was merged into saa7115 several bugs were introduced,
in particular with the saa7111a support as is used in the mxb.c driver.
This patch fixes the saa7111a support. This was tested with the mxb driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_register needs to be called before the i2c subdevs are loaded.
However, it was called afterwards in the saa7146 driver. This caused an oops
when loading the mxb and hexium drivers. The vv_init function is now split
into two: one registers the v4l2_device, the other does the rest of the
initialization. The three drivers that depend on this have been updated to
call the new vv_devinit function.
Thanks to Michael Hunold for reporting this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function return value wasn't checked due to a missing variable
assignment.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Asus EeePC T91 integrated webcam exposes a gain control in the
processing unit but stalls when the control is queried. Blacklist the
gain control for that camera.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When setting a control, the V4L2 specification requires drivers to
either clamp the control value to the [minimum, maximum] range or return
the -ERANGE error.
Fix the driver to clamp control values to the valid range in
uvc_ctrl_set() and make sure the value differs from the minimum by an
integer multiple of step.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2 specification states that out of bounds control values must
either be clamped to the valid range or result in a -ERANGE error code.
Fix the driver to return -ERANGE instead of -EINVAL when setting a menu
control to an invalid value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the UVC_GUID_FORMAT and UVC_GUID_ARGS macros with the new %pUl
printk format specifier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes timeout issues with some Logitech webcams. The timeout value
seems to match the one used in the Logitech Windows driver, so no
further increase should be necessary.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that volume values are always in the allowed range. Otherwise,
it would be possible to set other bits in the AUD_VOL_CTL register or to
get a wrong sign in the AUD_BAL_CTL register.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch addes timb-radio to all configurations of the timberdale MFD.
Connected to the FPGA is a TEF6862 tuner and a SAA7706H DSP, the I2C
board info of these devices is passed via the timb-radio platform data.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: sameo@linux.intel.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The parenthesis was misplaced, tmp is set to 0 or break occurs,
while debugging opera1_usb_i2c_msgxfer() retval was not shown.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
CC: Marco Gittler <g.marco@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A small mistake on the last patch broke demod s-code setup for
XC3028L (firmware 3.2 and upper). Fix it.
Thanks-to: Stefan Ringel <stefan.ringel@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
