Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.
Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.
Tested on BeagleBoard rev C2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* 'perf-counters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-perf: (31 commits)
perf_counter tools: Give perf top inherit option
perf_counter tools: Fix vmlinux symbol generation breakage
perf_counter: Detect debugfs location
perf_counter: Add tracepoint support to perf list, perf stat
perf symbol: C++ demangling
perf: avoid structure size confusion by using a fixed size
perf_counter: Fix throttle/unthrottle event logging
perf_counter: Improve perf stat and perf record option parsing
perf_counter: PERF_SAMPLE_ID and inherited counters
perf_counter: Plug more stack leaks
perf: Fix stack data leak
perf_counter: Remove unused variables
perf_counter: Make call graph option consistent
perf_counter: Add perf record option to log addresses
perf_counter: Log vfork as a fork event
perf_counter: Synthesize VDSO mmap event
perf_counter: Make sure we dont leak kernel memory to userspace
perf_counter tools: Fix index boundary check
perf_counter: Fix the tracepoint channel to perfcounters
perf_counter, x86: Extend perf_counter Pentium M support
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (21 commits)
Blackfin: define HARDIRQ_BITS again for now
arch/blackfin: Add kmalloc NULL tests
Blackfin: add CPLB entries for Core B on-chip L1 SRAM regions
Blackfin: work around anomaly 05000189
Blackfin: drop per-cpu loops_per_jiffy tracking
Blackfin: fix bugs in GPIO resume code
Blackfin: bf537-stamp: fix irq decl for AD7142
Blackfin: fix handling of IPEND in interrupt context save
Blackfin: drop duplicate runtime checking of anomaly 05000448
Blackfin: fix incomplete renaming of the bfin-twi-lcd driver
Blackfin: fix wrong CTS inversion
Blackfin: update handling of anomaly 364 (wrong rev id in BF527-0.1)
Blackfin: fix early_dma_memcpy() handling of busy channels
Blackfin: handle BF561 Core B memory regions better when SMP=n
Blackfin: fix miscompilation in lshrdi3
Blackfin: fix silent crash when no uClinux MTD filesystem exists
Blackfin: restore exception banner when dumping crash info
Blackfin: work around anomaly 05000281
Blackfin: update anomaly lists to match latest sheets/usage
Blackfin: drop dead flash_probe call
...
The Blackfin serial headers were inverting the CTS value leading to wrong
handling of the CTS line which broke CTS/RTS handling completely.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix i2c_board_info definitions - we were defining the 'type' field
of these structures twice since the first argument of I2C_BOARD_INFO
sets this field. Move the second definition into I2C_BOARD_INFO().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
The BSS section macros in vmlinux.lds.h currently place the .sbss
input section outside the bounds of [__bss_start, __bss_end]. On all
architectures except for microblaze that handle both .sbss and
__bss_start/__bss_end, this is wrong: the .sbss input section is
within the range [__bss_start, __bss_end]. Relatedly, the example
code at the top of the file actually has __bss_start/__bss_end defined
twice; I believe the right fix here is to define them in the
BSS_SECTION macro but not in the BSS macro.
Another problem with the current macros is that several
architectures have an ALIGN(4) or some other small number just before
__bss_stop in their linker scripts. The BSS_SECTION macro currently
hardcodes this to 4; while it should really be an argument. It also
ignores its sbss_align argument; fix that.
mn10300 is the only user at present of any of the macros touched by
this patch. It looks like mn10300 actually was incorrectly converted
to use the new BSS() macro (the alignment of 4 prior to conversion was
a __bss_stop alignment, but the argument to the BSS macro is a start
alignment). So fix this as well.
I'd like acks from Sam and David on this one. Also CCing Paul, since
he has a patch from me which will need to be updated to use
BSS_SECTION(0, PAGE_SIZE, 4) once this gets merged.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/fyu/linux-2.6:
Revert "Neither asm/types.h nor linux/types.h is required for arch/ia64/include/asm/fpu.h"
Add dma_debug_init() for ia64
Fix ia64 compilation IS_ERR and PTE_ERR errors.
asm/fpu.h uses the __IA64_UL macro which is declared in asm/types.h, so
this include is really required. Without it, GNU libc fails to build.
This reverts commit 2678c07b07.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
The commit 9916219579 was supposed to
add CONFIG_DMA_API_DEBUG support to IA64 however I forgot to add
dma_debug_init().
Signed-off-by: fujita <fujita@tulip.osrg.net>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
When building ia64 kernel with CONFIG_XEN_SYS_HYPERVISOR, compiler reports
errors:
drivers/xen/sys-hypervisor.c: In function ‘uuid_show’:
drivers/xen/sys-hypervisor.c:125: error: implicit declaration of function ‘IS_ERR’
drivers/xen/sys-hypervisor.c:126: error: implicit declaration of function ‘PTR_ERR’
This patch fixes the errors.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
Removed the LBD support that isn't of any use right now at least,
then remove remnants of the TCM config flags that somehow crept
in by mistake (not yet merged patch for 2.6.32) and then the usual
defconfig noise from updated menus.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid the following:
[ 0.012093] WARNING: at arch/x86/kernel/apic/apic.c:249 native_apic_write_dummy+0x2f/0x40()
Rather than chase each new cpuid-detected feature, just lie about the highest
valid CPUID so this code is never run.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The default values of HARDIRQ_BITS and PREEMPT_BITS in common code leads to
build failure:
In file included from include/linux/interrupt.h:12,
from include/linux/kernel_stat.h:8,
from arch/blackfin/kernel/asm-offsets.c:32:
include/linux/hardirq.h:66:2: error: #error PREEMPT_ACTIVE is too low!
So until that gets resolved, just declare our own default value again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Check that the result of kmalloc is not NULL before passing it to other
functions.
In the first two cases, the new code returns -ENOMEM, which seems
compatible with what is done for similar functions for other architectures.
In the last two cases, the new code fails silently, ie just returns,
because the function has void return type.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin SMP port was missing CPLB entries for Core B on-chip L1 SRAM
regions. Any code that attempted to use these would wrongly crash due to
a CPLB miss.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Similar to anomaly 05000281 but not as bad, we cannot return to the
instruction causing a fault otherwise we'll trigger a second false
exception. The system can still recover, but it isn't correct.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On Blackfin SMP, a per-cpu loops_per_jiffy is pointless since both cores
always run at the same CCLK. In addition, the current implementation has
flaws since the main consumer for loops_per_jiffy (asm/delay.h) uses the
global kernel loops_per_jiffy and not the per_cpu one. So punt all of the
per-cpu handling and go back to the global shared one.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Change the bfin_gpio_pm_hibernate_restore() function to:
1) AND restored DATA with DIR (not OR) to get correct final state
2) Restore DATA before setting DIR to avoid glitches
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The AD7142 add-on card hooks the IRQ line up to PG5, not PF5.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The interrupt context save logic incorrectly stored the address of the
IPEND register rather than its value due to a missing dereference. While
we're here, also enable this code for all kernel debugging scenarios and
not just when KGDB is enabled.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We already catch this anomaly at compile time, and the runtime version is
such that it ends up checking on all parts rather than just the ones that
might actually have it.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The sed used to rename the bfin-twi-lcd only replaced the first instance
rather than all which led to the resources not being enabled when the
driver was built as a module.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin serial headers were inverting the CTS value leading to wrong
handling of the CTS line which broke CTS/RTS handling completely.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This anomaly only applies to the BF527-0.1, not the BF526-0.1, and not any
other revision of the BF527. So make sure we don't go returning 0xffff
for other cases.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The early logic to locate a free DMA channel and then set it up was broken
in a few ways that only manifested itself when we needed to set up more
than 2 on chip SRAM regions (most board defaults setup 1 or 2). First, we
checked the wrong status register (the destination gets updated, not the
source) and second, we did the ssync before rather than after resetting a
DMA config register.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than assume Core B is always run with caches turned on, let people
load into any of the on-chip memory regions. It is their business how the
SRAM/Cache regions are utilized, so don't prevent them from being able to
load into them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The code used in the Blackfin lshrdi3 utilizes gcc constructs. However,
the structures declared don't line up with the code gcc generates, so
under certain optimizations, we get bad code and things crap out in fun
random ways. So rather than trying to maintain different gcc definitions
ourselves, just use the ones available in gcclib.h.
URL: http://blackfin.uclinux.org/gf/tracker/5286
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since we need to relocate the attached filesystem with the uClinux MTD map
(to handle some anomalies), we need to know its real filesize. If we boot
a kernel without a filesystem actually attached, we end up blindly reading
and copying garbage (since there is no magic value to detect validity).
Often times this results in an early crash and no output. So add a few
basic sanity checks before operating on things to catch the majority of
cases.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Previous unification code put the exception banner behind the "is oops"
logic when it should have been printed all the time.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add missing anomaly workaround for anomaly 05000281 - we can't return to
instructions which cause hardware errors otherwise we trigger the error
again which means we go into an infinite loop of handling, returning, and
retriggering. This work around confuses gdb when the error occurs as the
PC will seemed to have moved, so a better long term fix will need to be
figured out, but for now this is better than an infinite crash loop.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There are no CONFIG_{BLK,CHR}_DEV_FLASH Kconfig options, and there is no
flash_probe() function, so not really sure what this code is all about.
Seems to be dead code that stretches way back to the start of the Blackfin
port.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Improve the assembly with a few explanatory comments and use symbolic
defines rather than numeric values for bit positions.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When moving load_up_altivec to vector.S a typo in a comment caused a
thinko setting the wrong variable.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On booke processors, gdb is seeing spurious SIGTRAPs when setting a
watchpoint.
user_disable_single_step() simply quits when the DAC is non-zero. It should
be clearing the DBCR0_IC and DBCR0_BT bits from the dbcr0 register and
TIF_SINGLESTEP from the thread flag.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
when building 32-bit, I see this ..
arch/x86/kernel/pvclock.c:63:7: warning: "__x86_64__" is not defined
Signed-off-by: Dave Jones <davej@redhat.com>
LKML-Reference: <20090713201437.GA12165@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The variable apic_numaq placed in noninit section references the
function wakeup_secondary_cpu_via_nmi(), which is in __cpuinit
section. Thus causes a section mismatch warning. To avoid such
mismatch we mark apic_numaq as __refdata.
We were warned by the following warning:
WARNING: arch/x86/kernel/built-in.o(.data+0x932c): Section mismatch in
reference from the variable apic_numaq to the function
.cpuinit.text:wakeup_secondary_cpu_via_nmi()
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <b9df5fa10907120407p6b4f67dtf4d563155488188a@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The variable apic_es7000_cluster references the function __cpuinit
wakeup_secondary_cpu_via_mip() from a noninit section. So we've been
warned by the following warning. To avoid possible collision between
init/noninit, its best to mark the variable as __refdata.
We were warned by the following warning:
LD arch/x86/kernel/apic/built-in.o
WARNING: arch/x86/kernel/apic/built-in.o(.data+0x198c): Section
mismatch in reference from the variable apic_es7000_cluster to the
function .cpuinit.text:wakeup_secondary_cpu_via_mip()
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <b9df5fa10907120404k6279a10ch5e9682432272706f@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I've attached a patch to remove the Pentium M special casing of
EMON and as noticed at least with my Pentium M the hardware PMU
now works:
Performance counter stats for '/bin/ls /var/tmp':
1.809988 task-clock-msecs # 0.125 CPUs
1 context-switches # 0.001 M/sec
0 CPU-migrations # 0.000 M/sec
224 page-faults # 0.124 M/sec
1425648 cycles # 787.656 M/sec
912755 instructions # 0.640 IPC
Vince suggested that this code was trying to address erratum
Y17 in Pentium-M's:
http://download.intel.com/support/processors/mobile/pm/sb/25266532.pdf
But that erratum (related to IA32_MISC_ENABLES.7) does not
affect perfcounters as we dont use this toggle to disable RDPMC
and WRMSR/RDMSR access to performance counters. We keep cr4's
bit 8 (X86_CR4_PCE) clear so unprivileged RDPMC access is not
allowed anyway.
Cc: Vince Weaver <vince@deater.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@googlemail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The name size limit is gone from the driver-core, the BUS_ID_SIZE
value will be removed.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
