Doing 'WARN_ON(preempt_count())' was horribly horribly wrong, and would
cause tons of warnings at bootup if PREEMPT was enabled because the
initcalls currently run with the kernel lock, which increments the
preempt count.
At the same time, the warning was also insufficient, since it didn't
check that interrupts were enabled.
The proper debug function to use for something that can sleep and wants
a warning if it's called in the wrong context is 'might_sleep()'.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a mutex to the e1000e driver that would help
catch any collisions of two e1000e threads accessing hardware
at the same time.
description and patch updated by Jesse
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the stats lock is left over from e1000, e1000e no longer
has the adjust tbi stats function that required the addition
of the stats lock to begin with.
adding a mutex to acquire_swflag helped catch this one too.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
thanks to tglx, we're finding some interesting reentrancy issues.
this patch removes the phy read from inside a spinlock, paving
the way for removing the spinlock completely. The phy read was
only feeding a statistic that wasn't used.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
e1000e was apparently calling two functions that attempted to reserve
the SWFLAG bit for exclusive (to hardware and firmware) access to
the PHY and NVM (aka eeprom). These accesses could possibly call
msleep to wait for the resource which is not allowed from interrupt
context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
in the process of debugging things, noticed that the swflag is not reset
by the driver after reset, and the swflag is probably not reset unless
management firmware clears it after 100ms.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set the hardware to ignore all write/erase cycles to the GbE region in
the ICHx NVM. This feature can be disabled by the WriteProtectNVM module
parameter (enabled by default) only after a hardware reset, but
the machine must be power cycled before trying to enable writes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: arjan@linux.intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enabling the MIB interrupts has proven to cause an
interrupt storm after 7 hours of run. We will make use of the
MIB interrupt once we have ANI supported added so for now
to cure this we disable the interrupt.
The interrupt storm can be seen as follows after 7 hours of run
as reported by Steven Noonan <steven@uplinklabs.net>:
18:28:38 sum 1106.00
18:28:39 sum 1037.62
18:28:40 sum 1069.00
18:28:41 sum 1167.00
18:28:42 sum 1155.00
18:28:43 sum 1339.00
18:28:44 sum 18355.00
18:28:45 sum 17845.45
18:28:46 sum 15285.00
18:28:47 sum 17511.00
18:28:48 sum 17568.69
18:28:49 sum 17704.04
18:28:50 sum 18566.67
18:28:51 sum 18913.13
at 18:28:44 the MIB interrupt kicked off and caused huge
latency which can be seen even on a video he submitted:
http://www.youtube.com/watch?v=4GeCx1gZMpA
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
akpm: taken from http://bugzilla.kernel.org/show_bug.cgi?id=11587
I bought the wifi dongle trust nw-3100 wich is in fact a zd1211rw. Its
hardware id was missing in the sources, adding it made it work flawlessly.
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Connectivtiy is lost after Group rekeying is done. The keytype
maintained by ath9k is reset when group key is updated. Though
sc_keytype can be reset only for broadcast key the proper fix
would be to use mac80211 provided key type from txinfo during
xmit and get rid of sc_keytype from ath9k ath_softc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Tested-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix deadlock on RTNL between bcast join comp and ipoib_stop()
RDMA/nes: Fix client side QP destroy
IB/mlx4: Fix up fast register page list format
mlx4_core: Set RAE and init mtt_sz field in FRMR MPT entries
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
e100: Use pci_pme_active to clear PME_Status and disable PME#
e1000: prevent corruption of EEPROM/NVM
forcedeth: call restore mac addr in nv_shutdown path
bnx2: Promote vector field in bnx2_irq structure from u16 to unsigned int
sctp: Fix oops when INIT-ACK indicates that peer doesn't support AUTH
sctp: do not enable peer features if we can't do them.
sctp: set the skb->ip_summed correctly when sending over loopback.
udp: Fix rcv socket locking
Currently e100 uses pci_enable_wake() to clear pending wake-up events
and disable PME# during intitialization, but that function is not
suitable for this purpose, because it immediately returns error code
if device_may_wakeup() returns false for given device.
Make e100 use pci_pme_active(), which carries out exactly the
required operations, instead.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Andrey reports e1000 corruption, and that a patch in vmware's ESX fixed
it.
The EEPROM corruption is triggered by concurrent access of the EEPROM
read/write. Putting a lock around it solve the problem.
[akpm@linux-foundation.org: use DEFINE_SPINLOCK to avoid confusing lockdep]
Signed-off-by: Christopher Li <chrisl@vmware.com>
Reported-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Zach Amsden <zach@vmware.com>
Cc: Pratap Subrahmanyam <pratap@vmware.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
after
| commit f735a2a1a4
| Author: Tobias Diedrich <ranma+kernel@tdiedrich.de>
| Date: Sun May 18 15:02:37 2008 +0200
|
| [netdrvr] forcedeth: setup wake-on-lan before shutting down
|
| When hibernating in 'shutdown' mode, after saving the image the suspend hook
| is not called again.
| However, if the device is in promiscous mode, wake-on-lan will not work.
| This adds a shutdown hook to setup wake-on-lan before the final shutdown.
|
| Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
| Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
my servers with nvidia ck804 and mcp55 will reverse mac address with kexec.
it turns out that we need to restore the mac addr in nv_shutdown().
[akpm@linux-foundation.org: fix typo in printk]
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bnx2 driver stores/uses the irq value from the pci_dev internally.
But when it stores the irq value, it has been performing an
integer demotion. Because of the recent changes made to
arch/x86/kernel/io_apic.c, the new method in creating the irq value
(using build_irq_for_pci_dev()) has exposed this bug on x86 systems.
Because of this demotion when calling request_irq() from
bnx2_request_irq(), the driver would get a return code of -EINVAL.
This is because the kernel could not find the requested irq descriptor.
By storing the irq value properly, the kernel can find the correct
irq descriptor and the bnx2 driver can operate normally.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes kernel regression for 2.6.27-rc in
http://bugzilla.kernel.org/show_bug.cgi?id=11547
The change to split 8390 into old isa and non-isa versions
overlooked this driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit bc19d6e0b7, which as
Larry Finger reports causes the radio LED on his system to no longer
respond to rfkill switch events.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Requested-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Byte swap the addresses in the page list for fast register work requests
to big endian to match what the HCA expectx. Also, the addresses must
have the "present" bit set so that the HCA knows it can access them.
Otherwise the HCA will fault the first time it accesses the memory
region.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The reset_task function in the niu driver does not reset the tx and rx
buffers properly. This leads to panic on reset. This patch is a
modified implementation of the previously posted fix.
Signed-off-by: Santwona Behera <santwona.behera@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use TX control flag IEEE80211_TX_CTL_ASSIGN_SEQ as a request to update
the seq# for the frames. This will likely require some further cleanup
to get seq# correctly for Beacons vs. other frames and also potentially
for multiple BSSes. Anyway, this is better than ending up sending out
most frames with seq# 0.
(This is a backport of patch w/ same title already in net-next-2.6.
It is verified to fix http://bugzilla.kernel.org/show_bug.cgi?id=11394
and it should be acceptable for -rc due to the driver being new
in 2.6.27.)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix regression tracked as http://bugzilla.kernel.org/show_bug.cgi?id=11361
and caused by commit f735a2a1a4 ("[netdrvr]
forcedeth: setup wake-on-lan before shutting down") that makes network
adapters integrated into the NVidia MCP55 chipsets fail to work in kexeced
kernels. The problem appears to be that if the adapter is put into D3_hot
during ->shutdown(), it cannot be brought back into D0 after kexec (ref.
http://marc.info/?l=linux-kernel&m=121900062814967&w=4). Therefore, only
put forcedeth into D3 during ->shutdown() if the system is to be powered
off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2x: Accessing un-mapped page
ath9k: Fix TX control flag use for no ACK and RTS/CTS
ath9k: Fix TX status reporting
iwlwifi: fix STATUS_EXIT_PENDING is not set on pci_remove
iwlwifi: call apm stop on exit
iwlwifi: fix Tx cmd memory allocation failure handling
iwlwifi: fix rx_chain computation
iwlwifi: fix station mimo power save values
iwlwifi: remove false rxon if rx chain changes
iwlwifi: fix hidden ssid discovery in passive channels
iwlwifi: W/A for the TSF correction in IBSS
netxen: Remove workaround for chipset quirk
pcnet-cs, axnet_cs: add new IDs, remove dup ID with less info
ixgbe: initialize interrupt throttle rate
net/usb/pegasus: avoid hundreds of diagnostics
tipc: Don't use structure names which easily globally conflict.
The allocated RX buffer size was 64 bytes bigger than the PCI mapped
size with no good reason. If the packet was actually using the buffer up
to its limit and if the last 64 bytes of the buffer crossed 4KB boundary
then an unmapped PCI page was accessed. The fix is to use only one
parameter for the buffer size - there is no need to differentiate
between the buffer size and the PCI mapping size since the extra 64
bytes can actually be used by the FW to align the Ethernet payload to
64 bytes.
Also updating the driver version and date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets STATUS_EXIT_PENDING on pci_remove. Otherwise
iwl4965_down may fail to uninitialize the driver.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch calls apm stop on exit and suspend. Without this patch
hardware consumes power even after driver is removed or suspended.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch "iwlwifi: do not use GFP_DMA in iwl_tx_queue_init" removes
GFP_DMA from allocation tx command buffers. GFP_DMA allows allocation
only for memory under 16M which causes allocation problems
suspend/resume flows.
Using kmalloc is temporal solution and some consistent/coherent
allocation schema will be more correct. Since iwlwifi hardware
supports 64bit address this solution should work on x86 (32 and
64bit) for now.
This patch fixes memory freeing problem in the previous patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes rx_chain computation. The code that adjusts number of
rx chains to number supported by HW was missing. Miss configuration
causes firmware error. Note: iwlwifi supports HW with up to 3 RX
chains (2x2, 2x3, 1x2, and 3x3 MIMO). This patch also simplifies the
whole RX chain computation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the wrong use MIMO power save values. Our TX was
configured with our MIMO power save values instead of peer's MIMO power
save values, this may affect connectivity. The peer STA/AP may not sense
our traffic at all as it doesn't have all RX chains opened.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx chain might change during power save transitions but it doesn't
require sending Full-ROXN command to the firmware. Full-RXON requires
reconnection to an AP and thus affects user experience. The patch
avoids the Full-RXON by removing the rx_chain modification check in
iwl_full_rxon_required function.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables sending of direct probes on passive channels, as long as
traffic was detected on that channel. This enables connectivity to
hidden/non broadcasting SSIDs APs on passive channels. Note 5000 HW
declares all 5.2 spectrum as passive.
Signed-off-by: Cahill Ben <ben.m.cahill@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a W/A for the TSF sync issue in IBSS merging. HW is not
capable to sync TSF (it's constantly little behind). This creates
constant IBSS merging upon reception of each beacon, adding and removing
station which in turn creates above 50% packet loss and thus dramatically
degrade the throughput. The W/A simply stops the driver from declaring it
has a reliable TSF value and thus eliminates IBSS merging.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove chipset-specific quirk workaround; the workaround caused
unrecoverable DMA lockups when the driver was loaded following a
PXE boot.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This commit dropped the setting of the default interrupt throttle rate.
commit 021230d40a
Author: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Date: Mon Mar 3 15:03:45 2008 -0800
ixgbe: Introduce MSI-X queue vector code
The following patch adds it back. Without this the default value of 0
causes the performance of this card to be awful. Restoring these to the
default values yields much better performance.
This regression has been around since 2.6.25.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org [2.6.25 and later]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make the "pegasus" driver scream less loudly in the face of
problems as it initializes, avoiding hundreds of messages:
- ratelimit some key error messages
- avoid some spurious diagnostics caused by strange codeflow
And fix one instance of goofy indentation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipsec: Fix deadlock in xfrm_state management.
ipv: Re-enable IP when MTU > 68
net/xfrm: Use an IS_ERR test rather than a NULL test
ath9: Fix ath_rx_flush_tid() for IRQs disabled kernel warning message.
ath9k: Incorrect key used when group and pairwise ciphers are different.
rt2x00: Compiler warning unmasked by fix of BUILD_BUG_ON
mac80211: Fix debugfs union misuse and pointer corruption
wireless/libertas/if_cs.c: fix memory leaks
orinoco: Multicast to the specified addresses
iwlwifi: fix 64bit platform firmware loading
iwlwifi: fix apm_stop (wrong bit polarity for FLAG_INIT_DONE)
iwlwifi: workaround interrupt handling no some platforms
iwlwifi: do not use GFP_DMA in iwl_tx_queue_init
net/wireless/Kconfig: clarify the description for CONFIG_WIRELESS_EXT_SYSFS
net: Unbreak userspace usage of linux/mroute.h
pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock()
ipv6: When we droped a packet, we should return NET_RX_DROP instead of 0
This patch addresses an issue with the locking order. ath_rx_flush_tid()
uses spin_lock/unlock_bh when IRQs are disabled in sta_notify by mac80211.
As node clean up is still pending with ath9k and this problematic portion
of the code is expected to change anyway, thinking of a proper fix may not
be worthwhile. So having this interim fix helps the users to get rid of the
kernel warning message.
Pasted the kernel warning message for reference.
kernel: ath0: No ProbeResp from current AP 00:1b:11:60:7a:3d - assume out of range
kernel: ------------[ cut here ]------------
kernel: WARNING: at kernel/softirq.c:136 local_bh_enable+0x3c/0xab()
kernel: Pid: 1029, comm: ath9k Not tainted 2.6.27-rc4-wt-w1fi-wl
kernel:
kernel: Call Trace:
kernel: [<ffffffff802278d8>] warn_on_slowpath+0x51/0x77
kernel: [<ffffffff80224c51>] check_preempt_wakeup+0xf3/0x123
kernel: [<ffffffff80239658>] autoremove_wake_function+0x9/0x2e
kernel: [<ffffffff8022c281>] local_bh_enable+0x3c/0xab
kernel: [<ffffffffa01ab75a>] ath_rx_node_cleanup+0x38/0x6e [ath9k]
kernel: [<ffffffffa01b2280>] ath_node_detach+0x3b/0xb6 [ath9k]
kernel: [<ffffffffa01ab09f>] ath9k_sta_notify+0x12b/0x165 [ath9k]
kernel: [<ffffffff802366cf>] queue_work+0x1d/0x49
kernel: [<ffffffffa018c3fc>] add_todo+0x70/0x99 [mac80211]
kernel: [<ffffffffa017de76>] __sta_info_unlink+0x16b/0x19e [mac80211]
kernel: [<ffffffffa017e6ed>] sta_info_unlink+0x18/0x43 [mac80211]
kernel: [<ffffffffa0182732>] ieee80211_associated+0xaa/0x16d [mac80211]
kernel: [<ffffffffa0184a1a>] ieee80211_sta_work+0x4fb/0x6b4 [mac80211]
kernel: [<ffffffff80469c58>] thread_return+0x30/0xa9
kernel: [<ffffffffa018451f>] ieee80211_sta_work+0x0/0x6b4 [mac80211]
kernel: [<ffffffff802362c2>] run_workqueue+0xb1/0x17a
kernel: [<ffffffff80236be9>] worker_thread+0xd0/0xdb
kernel: [<ffffffff8023964f>] autoremove_wake_function+0x0/0x2e
kernel: [<ffffffff80236b19>] worker_thread+0x0/0xdb
kernel: [<ffffffff8023954a>] kthread+0x47/0x75
kernel: [<ffffffff80223121>] schedule_tail+0x18/0x50
kernel: [<ffffffff8020bc49>] child_rip+0xa/0x11
kernel: [<ffffffff80239503>] kthread+0x0/0x75
kernel: [<ffffffff8020bc3f>] child_rip+0x0/0x11
kernel:
kernel: ---[ end trace e9bb5da661055827 ]---
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updating sc_keytype multiple times when groupwise and pairwise
ciphers are different results in incorrect pairwise key type
assumed for TX control and normal ping fails. This works fine
for cases where both groupwise and pairwise ciphers are same.
Also use mac80211 provided enums for key length calculation.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A "Set" to a sign-bit in an "&" operation causes a compiler warning.
Make calculations unsigned.
[ The warning was masked by the old definition of BUILD_BUG_ON() ]
Also remove __builtin_constant_p from FIELD_CHECK since BUILD_BUG_ON
no longer permits non-const values.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The leak in if_cs_prog_helper() is obvious.
It looks a bit as if not freeing "fw" in if_cs_prog_real() was done
intentionally, but I'm not seeing why it shouldn't be freed.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multicasting the driver sets the number of group addresses using
the count from the previous set multicast command. In general this means
you have to set the multicast addresses twice to get the behaviour you
want.
If we were multicasting, and reduce the number of addresses we are
multicasting to, then the driver would write uninitialised data from the
stack into the group addresses to multicast to.
Only write the multicast addresses we have specifically set.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes loading firmware from memory above 32bit.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Marcel Holtmann <holtmann@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes CSR_GP_CNTRL_REG_FLAG_INIT_DONE was set instead of
cleared which disabled moving device to D0U state.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
