otg_ulpi_create is defined in drivers/usb/otg/ulpi.c which depends on
CONFIG_USB_ULPI. So protect its usage by the same symbol. Moreover
mxc_ulpi_access_ops needs CONFIG_MXC_ULPI.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, linux-next breaks due to a typo introduced in commit
33c4d91928
This patch fixes it.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adds requirement for ADC on mc13783 and moves the spidev declaration
to marxbot file.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We have two mt9t031 cameras that have a muxed bus on the robot.
Only one is currently initialized because of limitations in
soc_camera that should be removed later.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We get rid of CTS/RTS lines on uart0 on our platform.
This is the port we use as main kernel console. We do not
want it to be blocking because of CTS/RTS signals, not allowing
the system to boot or print messages.
However we often use it with a bluetooth module needing CTS/RTS
lines as backup login in case of trouble. To be able to use it,
we assert CTS low so that the module can always send chars.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These gpios are exported to userspace and are here to be used as
a selector
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since all boards finally have this device
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Small confusion with our hardware engineer, the WP signal (RO) is
active low on our boards, the signal has to inverted.
This is a pretty straightforward patch, it could even go to -rc,
but if not, then push it for 2.6.32.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is used on all board of our system, so again this is done in the
mx31moboard.c file.
changes since v2: call to gpio_request added in platform code, and
moved device initialization in baseboard files.
changes since v1: pins are claimed in another patch
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to use the gpiolib, we now have to call gpio_request in
the plaform code since it is not done in iomux code anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This support both sdhc1 and sdhc2 with WP and CD for the marxbot and
devboard mx31moboard baseboards.
sdhc2 is present on both, but is not directly included in the
mx31moboard file because a third baseboard (not supported yet) without
sdhc2 is planned.
Changes since v1: removed pin initialization from init/exit function and
taken different comments into account
Changes since v2: pin initialiation now is done in another patch for all
current mx31moboard pins
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Changes since v1: all the pins needed for the drivers are claimed in
another patch
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As suggested by Sascha, here we setup all the pins that we are using in
the current (and currently reviewed) drivers for mx31moboard system.
changes since v1: changed I2C1 pin names
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Various improvements (includes in alphabetical order, platform devices
declaration order change, ...)
The pins now are claimed in a single function call from a main table for
every board for a better clarity and to adopt the current agreement for
mx31 devices.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows us to have more mapping functions for more than one
i.MX architecture in the kernel. As this is the earliest board
specific hook we have, also use it to set the cpu type.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On MX31 we can't do much without mapping the AIPS1/2 register space.
Move these mappings from individual boards to plat-mxc/mm.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the dma (ipu_dma) and fb devices for the mx31 for which drivers now are
available.
v2: merge the ipu and fb device in the same patch as suggested by Sascha
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This enables our mx31moboard to be used on the different baseboards that
we are developping according to the application needs. There are not
many differences between the boards for now, but when other peripherals
are available for mx31 the differences are going to grow.
v2: takes Sascha's comments into account
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This example takes advantage of the possibility to use tables of iomux
configs.
This is inspired from mx1-mx2 iomux code. It allows a better code
readability.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- rename mxc_clocks_init to architecture specific versions. This
allows us to have more than one architecture compiled in.
- call mxc_timer_init from clock initialisation instead from board
code
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Initial support for mx31moboard platfor with 3 serial ports
and NOR Flash
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
