Earlier revisions of the wm5110/8280 silicon require a slightly more
complex procedure to enable analogue inputs. This patch adds this into
the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduced by:
commit 8019ff6cfc
("regmap: Use reg_sequence for multi_reg_write / register_patch")
Interacting with:
commit d1acd31883
("ASoC: wm5110: Add special DRE on/off handling for the headphone path")
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we fail to add some DSPs or fail to add the controls we should call
wm_adsp2_codec_remove for all the cores we have already added. This
patch fixes this up on the wm5102 and wm5110.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For the best performance the headphone path enable/disable must be
handled specially for the situations of DRE on and DRE off.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Specifying unstable coefficients for the low/high pass filters can have
a severe impact on the audio. This patchs adds a stability check on the
coefficients written to the low/high pass filter block to prevent this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Specifying unstable coefficients for the EQ can have a severe impact on
the audio. This patchs adds a stability check on the coefficients
written to the EQ, for this it is necessary to merge the mode control
and the coefficients as some coefficients may only be unstable with a
certain mode setting so it is ideal if these are always updated in sync.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rate controls are codec-specific, it's not possible to
generically say what the range or the meaning of each control
is (or even if they exist at all) - that depends on the
particular codec.
This is currently being handled for Arizona codecs by putting
an Arizona-specific table of controls inside the wm_adsp driver.
This creates a dependency between wm_adsp and arizona.c, and is an
awkward solution if the ADSP is used in another family of codecs
Fix this by moving the Arizona-specific rate controls into the
Arizona codec drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have a codec_probe stage initialization in the wm_adsp
driver, we can make the wm_adsp driver create its own ALSA controls
instead of having that responsibility pushed to every codec driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the only init function in wm_adsp is called by the
codec driver early in its probe before the codec has been
registered with SOC.
This patch adds stubs for the codec_probe and codec_remove stages
and calls them from WM5102 and WM5110 codec drivers. This allows us
to hang anything that needs setup during the codec probe stage off
these functions without further modification of the codec drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In theory the ADSP driver should not need to know anything
about the codec it is part of. But the WM5102 needs DVFS
control based on ADSP clocking speed. This was being handled
by bundling part of the knowledge of this into the ADSP driver.
This change moves this handling out of the ADSP driver and
into the WM5102 driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to codec->dapm
with snd_soc_codec_get_dapm().
While we are at it also remove the duplicated initialization of
priv->core.arizona->dapm.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona codec drivers had an incorrect dB scaling for the
noise generator gain that started at 0dB and went upwards.
Actually the highest setting is 0dB.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Save a bit of scheduling by coalescing all the output power up delays
into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give the output disable sequence a chance to fully complete, otherwise
there is a danger we may remove the clock before it is finished
resulting in a pop noise. The delay for each output must be cumulative
and these are coalesced into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Different playback and capture bits-per-sample
are not supported on the AIFs
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
On the wm5110 CODEC both the left and right channel must be powered
when an output is being used as a mono output, although no audio is
routed to the right output channel. This patch adds additional DAPM
routes to link the right channel to the left in the case where an output
is marked as mono. Audio must always be brought in on the left channel
for mono operation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SOC_VALUE_ENUM, SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated
and merely an alias for SOC_ENUM, SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace
the deprecated macros so we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some thing Likes:
reproduce: make C=1 CF=-D__CHECK_ENDIAN__
sparse warnings: (new ones prefixed by >>)
>> sound/soc/codecs/wm8997.c:1084:15: sparse: symbol \
'wm8997_get_regmap' was not declared. Should it be static?
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are no OSR controls on outputs 1-4 on wm5110, however when these
were removed the ones on output 5 and 6 were also accidentally removed,
but those actually exist. This patch adds these controls back in.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that all users have been converted to regmap and the config.reg_bits
and config.val_bits can be setted by each user through regmap core API.
So these two params are redundant here.
Since the only control type that left is SND_SOC_REGMAP, so remove it. Drop
the control params and add struct regmap *regmap to simplify the code.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With the ongoing component-ization of the ASoC framework and the continuing
migration to using regmap for IO the control_data field of the snd_soc_codec
struct will eventually be removed. Prepare the wm5192, wm5110 and wm8997
drivers for this by using arizona->regmap instead of accessing the CODEC's
control_data field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The EQ coefficient binary controls overlapped with the volume controls
for the B4 and B5 volumes, which were controllable from either the
coefficient control or the volume control itself.
This patch adds controls for the mode and moves the coefficient control
to only cover the coefficients.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Latest evaluation of the the device has given some patch file additions
for improved performance.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Add controls to enable/disable the headphone short circuit protection of
the headphone outputs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for configuring the sample rate on the SYSCLK side of the
ASRC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently, the driver only supports configuration of the lower sample
rate (FSL) on the ISRCs. With the higher rate being fixed a SYSCLK, this
patch adds support for configuring the higher sample rate (FSH).
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Certain use-cases require the DRE to be disabled so expose controls for
the enables.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reported-by: Kyung-Kwee Ryu <kyung-kwee.ryu@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
When writing the patch write to the device asynchronously, allowing better
performance when used with a bus like SPI which supports this by
minimising the need to context switch back to the driver to get the
next bit of data.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
These are managed automatically in current revisions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the ISRCs that matches the current support on the w5102.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
