None of the drives I have follows what the standard says about
transfer chunk size. Of the four SATA and six PATA ATAPI devices
tested, four ignore transfer chunk size completely and the ones which
honor it don't behave according to the spec when it's odd.
According to the spec, transfer chunk size can be odd if the amount of
data to transfer equals or is smaller than the chunk size and the
device can indicate the same odd number and transfer the whole thing
at one go with a pad byte appended. However, in reality, none of the
drives I have does that. They all indicate and transfer even number
of bytes one byte shorter than the chunk size first; then indicate and
transfer two bytes, which is clearly out of spec.
In addition to unnecessary second PIO data phase, this also creates a
weird problem when combined with SATA controllers which perform PIO
via DMA. Some of these controllers use actualy number of bytes
received to update DMA pointer so chunks which are sized 4n + 2 makes
DMA pointer off by two bytes. This causes data corruption and buffer
overruns.
This patch rounds nbytes up to the nearest even number such that ATAPI
devices don't split data transfer for the last odd byte. This
shouldn't confuse controllers which depend on transfer chunk size as
devices will report the rounded-up number, actually transfer that much
and padding buffer is there to receive them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While adding sg chaining support to iSER, a "for" loop was replaced
with a "for_each_sg" loop. The "for" loop included the incrementation
of 2 variables. Only one of them is incremented in the current
"for_each_sg" loop. This caused iSER to think that all data is
unaligned, and all data was copied to aligned buffers.
This patch increments the missing counter inside the "for_each_sg"
loop whenever necessary.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrong choice of port number caused modify_qp() to fail -- fixed.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Accidently I reversed the order of pci_save_state and
pci_set_power_state in .suspend()/.resume() callbacks
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
smc911x_set_multicast_list fails to fill out the multicast hash table
correctly; Bit 1 was used rather than bit 5 to decide if the lower or
upper register should be used.
The function is at the same time cleaned up by calling ether_crc rather
than using it's own bit reversal table.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Marvell Yukon XL chipset appears to have a hardware glitch
where it will repeat the checksum of the last packet. Of course, this is
timing sensitive and only happens sometimes...
More info: http://bugzilla.kernel.org/show_bug.cgi?id=9381
As a workaround just disable hardware checksumming by default on
this chip version. The earlier workaround for PCIX, dual port
was also on Yukon XL so don't need to disable checksumming there.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent driver from brawly logging packet checksum errors.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using own tx_packets counter instead of firmware counters.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x_local pointer in smc911x_rcv is only used in the SMC_USE_DMA
case. Move it under the #ifdef so GCC doesn't generate a warning in the
non-DMA case.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
elif defined(CONFIG_*) should be used instead of elif CONFIG_*
so GCC doesn't give warnings about undefined symbols when the config
option is disabled.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The amd8111e network driver was broken by
bea3348eef, which makes the driver
call napi_enable() and napi_disable() even if the driver had been
configured without CONFIG_AMD8111E_NAPI, and thus
netif_napi_add() had not been called on initialization.
This triggers a BUG in napi_enable().
This patch fixes the problem. Please apply.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A printk in the error handling code of dm9601.c was missing a newline.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a long boot delay in the forcedeth driver. During initialization, the
timeout for the handshake between mgmt unit and driver can be very long.
The patch reduces the timeout by eliminating a extra loop around the
timeout logic.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9308
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Alex Howells <astinus@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds new device ids and features for mcp79 devices into the
forcedeth driver.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It's a bad idea to call flush_scheduled_work from within a
netdev->stop because the linkwatch will occasionally take the
rtnl lock from a workqueue context, and thus that can deadlock.
This reworks things a bit in that area to avoid the problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a card has no IRQ then pass no interrupt handler but allow polled
usage.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hopefully there is a better long term solution but for now lets favour
reliability.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sil24 unnecessarily used LIBATA_MAX_PRD and ATAPI sg table was short
by one entry which might cause very obscure problems. This patch
updates sg table sizing such that
* One full page is used for PRB + sg table. On 4k page,
this results in 253 sg's.
* Make ATAPI sg block properly sized.
* Make build fail if command block size doesn't equal PAGE_SIZE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are two bugs in disabled port handling.
* test in PORT_PATA0 is reversed
* ->prereset should return -ENOENT for disabled ports not 0
The first bug makes the PATA channel considered disabled but the
second bug saves the day by returning 0. The net result is that cable
is always left at ATA_CBL_UNKNOWN. This results in false 80c
configuration and thus transfer errors.
This patch fixes both bugs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since writing to two reserved bits ain't much of a housekeeping, I think it's
time we get rid of the custom error handler in this driver. ;-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, gpio_keys.c assumes the GPIOs to be already properly configured;
this patch changes gpio-keys to perform explicit calls to gpio_request() and
gpio_configure_input().
This matches the behaviour of leds-gpio.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When booting under Microsoft Virtual Machine, the noloop quirk is
needed, otherwise PS/2 mouse is not properly detected.
Reported-by: Lawrence Steeger <vendor@russte.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We know exactly what IRQ we are using, so synchronize_irq()
suits much better. Plus synchronize_sched() will not work
for us in -rt kernels.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mattia Dongili <malattia@linux.it>
Properly set up parent on input devices registered by sonypi.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mattia Dongili <malattia@linux.it>
Properly set up parent on input devices registered by sony-laptop.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mattia Dongili <malattia@linux.it>
Move the code which marks the minor number as free to mmc_blk_put() so
that it happens on the final close() (or removal), instead of doing it
at removal even when the device is still logically open.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is possible to handle arbitrary block sizes with tifm card reader by
conditionally switching to PIO in case such block has to be delivered. At
the beginning of each request, DMA is either disabled (non-power-of-2 block
size) or set to load time user preference.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cards have been reported to signal that they're ready prematurely.
Checking both the busy bit and card state solves the issue.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers fail to send confirmation GPE after address or data write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e736), which did only read address.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9327
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Tested-by: Mats Johannesson
Signed-off-by: Len Brown <len.brown@intel.com>
Sometimes it is usefull to see raw protocol dump.
Uncomment '#define DEBUG' at the beginning of file to make EC
really verbose.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
When checking the states passed in, mlx4_qp_modify() accidentally checks
cur_state twice rather than checking cur_state and new_state. Fix this
to make sure that both values are in-bounds.
Since these values may be passed in from userspace, this bug results in
userspace being able to trigger an oops.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: stable <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error codes for ib_post_send(), ib_post_recv(), and ib_post_srq_recv()
were inconsistent. Use EINVAL for too many SGEs and ENOMEM for too many
WRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The wrong offset was being returned to libipathverbs so that when
ibv_modify_srq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the code which frees the partially allocated QP
resources if there was an error while creating the QP. In particular,
the QPN wasn't deallocated and the QP wasn't removed from the hash
table.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The wrong offset was being returned to libipathverbs so that when
ibv_resize_cq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make sure all subchannel handling is done on the slow path workqueue
so that we don't have races between an old subchannel unregistering
and a new subchannel with the same name registering.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Modify the sense id channel program to allow device sensing of pav
alias devices which belong to a base device with ungrouped paths.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9355
cpuidle always used to fallback to C2 if there is some bm activity while
entering C3. But, presence of C2 is not always guaranteed. Change cpuidle
algorithm to detect a safe_state to fallback in case of bm_activity and
use that state instead of C2.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Port 2aa44d0567
(sched: sched_clock_idle_[sleep|wakeup]_event()) to cpuidle.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Port 18eab85503
(Enable C3 even when PM2_control is zero) to cpuidle.
Without this patch, some systems will notice a regression
when enabling CPU_IDLE -- C3 would no longer be available.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
set_ibm_param() could OOPS with a NULL pointer derreference if one did not give
any values for a module parameter it handles. This would, of course, cause all
sort of trouble for future modprobing and require a reboot to clean up
properly.
Fix it by returning -EINVAL if no values are given for the parameter, and also
avoid any nastyness from BUG_ON while at it.
How to reproduce: modprobe thinkpad-acpi brightness
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Tested-by: Mike Kershaw <dragorn@kismetwireless.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce new ACPI_PROCFS_POWER (default Yes) config option and move
procfs code in battery, ac, and sbs drivers under it.
This is done to allow ACPI_PROCFS to be default No.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
In order to be able to write the value "100"
to /proc/acpi/video/.../brightness, we have to allocate 5 bytes:
4 characters will be written (1, 0, 0 plus null byte),
and 1 byte should be buffer for a terminating NULL character.
http://bugzilla.kernel.org/show_bug.cgi?id=9278
Signed-off-by: Danny Baumann <dannybaumann@web.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some controllers fail to send confirmation GPE after address write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e736), which did only read address.
http://bugzilla.kernel.org/show_bug.cgi?id=9327
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ICH8 and 9 use two SFF controllers to show 6 SATA ports. The first
controllre hosts the first 4 ports while the second one hosts the last
2. The PCS register of the first controller encompasses the first
four ports or all six ports depending on configuration while PCS of
the second controller controls the last two ports. Using 0xf for the
first controller and 0x3 for the second controller always result in
the correct configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ICH8M on apple macbook pro occasionally locks up completely during PCS
initialization if ports other than the first one are enabled. Add a
separate controller ID and only enable the first port.
tj: commit description added and patch updated to fit with the
previous controller ID update.
Signed-off-by: Thomas Rohwer <tr@tng.de>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Move piix_pata_mwdma to top, rename ich9_2port_sata to ich8_2port_sata
for consistency and use automatically incremented values instead of
assigning fixed values to ease adding new controller IDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Sebastian Kemper reported that issuing CD/DVD commands under libata is
not fully compatible with ide-scsi. In particular, the
GPCMD_SET_STREAMING was being rejected at the host level in some
instances.
The reason is that libata-scsi insists upon the cmd_len field exactly
matching the SCSI opcode being issued, whereas ide-scsi tolerates
12-byte commands contained within a 16-byte (cmd_len) CDB.
There doesn't seem to be a good reason for us to not be compatible
there, so here is a patch to fix libata-scsi to permit SCSI opcodes so
long as they fit within whatever size CDB is provided.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Per Mark's comments, maybe all ATAPI tape drives need ATA_HORKAGE_STUCK_ERR.
This patch applys ATA_HORKAGE_STUCK_ERR for all ATAPI tape drives.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
After an error condition, some ATAPI tape drives set DRQ=1 together
with ERR=1 when asking the host to transfer the CDB of the next packet
command (i.e. request sense). This patch, a revised version of
Alan/Mark's previous patch, adds ATA_HORKAGE_STUCK_ERR to workaround
the problem by ignoring the ERR bit and proceed sending the CDB.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Satellite U205 has alternate product name where the satellite part is
all capatalized. Add it to the blacklist.
This is reported by Ross Patterson in kernel bugzilla bug #7780.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ross Patterson <me@rpatterson.net>
The usb max packet size won't change during the
device's presence. We should store it in a
variable inside rt2x00dev and use that.
This should also fix a division error when the
device is being hot-unplugged while a frame is
being send out.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The virtio code never hooked through the ->remove callback. Although
noone supports device removal at the moment, this code is already
needed for module unloading.
This of course also revealed bugs in virtio_blk, virtio_net and lguest
unloading paths.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
drivers/acpi/sbs.c: In function acpi_battery_add:
drivers/acpi/sbs.c:811: warning: ignoring return value of device_create_file,
declared with attribute warn_unused_result
Additional cleanups:
* use struct acpi_battery in acpi_battery_remove() to clean up function
calls, just like acpi_battery_add() already does.
* put braces around unregister call, as it depends on dev being not NULL.
* remove unneeded braces
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Add throttling control via MSR when T-states uses
the FixHW Control Status registers.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously _PDC was evaluated later, and thus we'd not get
the chance to tell the BIOS that we can suport FixedHW registers (MSRs)
and the BIOS would always ask us to use System I/O access
for throttling.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_TSS was erroneously ignored, in favor of the FADT.
When TSS is used, the access width is included in the PTC control/status
register. So it is unnecessary that the access bit width is multiplied by 8.
At the same time the bit_offset should be considered for system I/O Access.
It should be checked the bit_width and bit_offset of PTC regsiter in order to
avoid the failure of system I/O access. It means that bit_width plus
bit_offset can't be greater than 32.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change the function interface for throttling control via PTC.
The following functions are concerned:
acpi_read_throttling_status()
acpi_write_throttling_state()
acpi_get_throttling_value()
acpi_get_throttling_state()
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Factor out legacy FADT.duty_width code
and run it only in the non _TSS case.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We've run into BIOS that hand us 4-bit access width requests
for T-state control when the code expected only multipls of 8-bits.
Round up.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When a T-state limit change notification is received,
Linux must evaluate _TPC and change its current
T-state immediately to comply with the new limit.
Previously, Linux would notice the new limit
only upon the next throttling change.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: Fix NULL pointer dereference in nf_nat_move_storage()
[SUNHME]: VLAN support for sunhme
[CHELSIO]: Fix skb->dev setting.
[NETFILTER]: fix compat_nf_sockopt typo
[INET]: Fix potential kfree on vmalloc-ed area of request_sock_queue
[VIA_VELOCITY]: Don't oops on MTU change.
iwl4965: fix not correctly dealing with hotunplug
rt2x00: Fix chipset revision validation
iwl3945: place CCK rates in front of OFDM for supported rates
mac80211: Fix queuing of scan containing a SSID
This patch enables VLAN support on sunhme by increasing BMAC_TXMAX/BMAC_RXMAX
and allocating extra space via skb_put for the VLAN header.
Signed-off-by: Chris Poon <dev-null@telus.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_type_trans() now sets skb->dev. Access skb->def after it gets
set.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c/eeprom: Recognize VGN as a valid Sony Vaio name prefix
i2c/eeprom: Hide Sony Vaio serial numbers
i2c-pasemi: Fix NACK detection
i2c-pasemi: Replace obsolete "driverfs" reference with "sysfs"
i2c: Make i2c_check_addr static
i2c-dev: Unbound new-style i2c clients aren't busy
i2c-dev: "how does it work" comments
Recent (i.e. 2005 and later) Sony Vaio laptops have names beginning
with VGN rather than PCG. Update the eeprom driver so that it
recognizes these.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sysfs interface to DMI data takes care to not make the system
serial number and UUID world-readable, presumably due to privacy
concerns. For consistency, we should not let the eeprom driver
export these same strings to the world on Sony Vaio laptops.
Instead, only make them readable by root, as we already do for BIOS
passwords.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Turns out we don't actually check the status to see if there was a
device out there to talk to, just if we had a timeout when doing so.
Add the proper check, so we don't falsly think there are devices
on the bus that are not there, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_check_addr is only used inside i2c-core now, so we can make it
static and stop exporting it. Thanks to David Brownell for noticing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let i2c-dev deal properly with new-style i2c clients. Instead of
considering them always busy, it needs to check wether a driver is
bound to them or not.
This is still not completely correct, as the client could become
busy later, but the same problem already existed before new-style
clients were introduced. We'll want to fix it someday.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
This adds some "how does this work" comments to the i2c-dev driver,
plus separators between the three main components:
- The parallel list of i2c_adapters ("i2c_dev_list"), each of which
gets a "struct i2c_dev" and a /dev/i2c-X character special file.
- An i2cdev_driver gets adapter add/remove notifications, which are
used to maintain that list of adapters.
- Special file operations, which let userspace talk either directly to
the adapter (for i2c_msg operations) or through cached addressing info
using an anonymous i2c_client (never registered anywhere).
Plus there's the usual module load/unload record keeping.
After making sense of this code, I think that the anonymous i2c_client
is pretty shady. But since it's never registered, using this code with
a system set up for "new style" I2C drivers is no more complicated than
always using the I2C_SLAVE_FORCE ioctl (instead of I2C_SLAVE).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This reverts commit 7fb7ac2411.
Heikki Orsila reports that it causes a regression:
"Doing
nc host port < /dev/zero
on a sending machine (not skge) to an skge machine that is receiving:
nc -l -p port >/dev/null
with ~60 MiB/s speed, causes the interface go malfunct. A slow
transfer doesn't cause a problem."
See
http://bugzilla.kernel.org/show_bug.cgi?id=9321
for some more information.
There is a workaround (also reported by Heikki):
"After some fiddling, I noticed that not changing the register write
order on patch:
+ skge_write32(hw, RB_ADDR(q, RB_END), end);
skge_write32(hw, RB_ADDR(q, RB_WP), start);
skge_write32(hw, RB_ADDR(q, RB_RP), start);
- skge_write32(hw, RB_ADDR(q, RB_END), end);
fixes the visible effect.. Possibly not the root cause of the
problem, but changing the order back fixes networking here."
but that has yet to be ack'ed or tested more widely, so the whole
problem-causing commit gets reverted until this is resolved properly.
Bisected-and-requested-by: Heikki Orsila <shdl@zakalwe.fi>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple mtu change when device is down.
Fix http://bugzilla.kernel.org/show_bug.cgi?id=9382.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Fix thinko in QP destroy (incorrect bitmap_free)
RDMA/cxgb3: Set the max_qp_init_rd_atom attribute in query_device
IB/ehca: Fix static rate calculation
IB/ehca: Return physical link information in query_port()
IB/ipath: Fix race with ACK retry timeout list management
IB/ipath: Fix memory leak in ipath_resize_cq() if copy_to_user() fails
mlx4_core: Fix possible bad free in mlx4_buf_free()
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: rt_check_expire() can take a long time, add a cond_resched()
[ISDN] sc: Really, really fix warning
[ISDN] sc: Fix sndpkt to have the correct number of arguments
[TCP] FRTO: Clear frto_highmark only after process_frto that uses it
[NET]: Remove notifier block from chain when register_netdevice_notifier fails
[FS_ENET]: Fix module build.
[TCP]: Make sure write_queue_from does not begin with NULL ptr
[TCP]: Fix size calculation in sk_stream_alloc_pskb
[S2IO]: Fixed memory leak when MSI-X vector allocation fails
[BONDING]: Fix resource use after free
[SYSCTL]: Fix warning for token-ring from sysctl checker
[NET] random : secure_tcp_sequence_number should not assume CONFIG_KTIME_SCALAR
[IWLWIFI]: Not correctly dealing with hotunplug.
[TCP] FRTO: Plug potential LOST-bit leak
[TCP] FRTO: Limit snd_cwnd if TCP was application limited
[E1000]: Fix schedule while atomic when called from mii-tool.
[NETX]: Fix build failure added by 2.6.24 statistics cleanup.
[EP93xx_ETH]: Build fix after 2.6.24 NAPI changes.
[PKT_SCHED]: Check subqueue status before calling hard_start_xmit
Declare mac using DECLARE_MAC_BUF for use when calling print_mac().
This fixes compile error where mac was undeclared.
Also, remove unused variable i.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New and improved serial driver for CRISv10, take three, with improvements
suggested by Jiri Slaby.
- Call wait_event_interruptible with a _correct_ and sensible condition.
- Removed superfluous test of info->flags & ASYNC_CLOSING, since that is done
by wait_event_interruptible.
- Moved common code for deregistering DMA and IRQ to deinit_port function.
- Use setup_timer when initializing flush_timer.
- Convert bit-field for uses_dma_in and uses_dma_out to regular bytes.
- Removed CVS tags.
- Removed defines and comments for CRIS_BUF_SIZE and TTY_THRESHOLD_THROTTLE
(no longer used).
- Cleaned up code to pass checkpatch.
- Add crisv10.h header file.
- Merge of CRISv10 from Axis internal CVS.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New (updated) version of ethernet driver for cris v10.
- First steps to simplify and make the MII code more similar
between the etrax100 and etraxfs ports.
- Start the transmit queue before enabling tx interrupts
to avoid race with the first frame.
- Flip the comparition statement to stick to physical addresses
to avoid phys_to_virt mapping a potential null pointer.
This was not an error but the change simplifies debugging
of address-space mappings.
- Made myPrevRxDesc local to e100_rx since it was only used there.
Fixed out of memory handling in e100_rx. If dev_alloc_skb() fails
persistently the system is hosed anyway but at least it won't
loop in an interrupt handler.
- Correct some code formatting issues.
- Add defines SET_ETH_ENABLE_LEDS, SET_ETH_DISABLE_LEDS
and SET_ETH_AUTONEG used in new cris v10 ethernet driver.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arm:
drivers/scsi/aic94xx/aic94xx_sds.c:381:1: warning: "FLASH_SIZE" redefined
In file included from include/asm/arch/irqs.h:22,
from include/asm/irq.h:4,
from include/asm/hardirq.h:6,
from include/linux/hardirq.h:7,
from include/asm-generic/local.h:5,
from include/asm/local.h:1,
from include/linux/module.h:19,
from include/linux/device.h:21,
from include/linux/pci.h:52,
from drivers/scsi/aic94xx/aic94xx_sds.c:28:
include/asm/arch/platform.h:444:1: warning: this is the location of the previous definition
Cc: Gilbert Wu <gilbert_wu@adaptec.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove redundant code leading to NULL ptr deref and let terminal config
settings take place in the proper initialization path in
usb_console_setup().
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: <lucy@keyspan.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check if AC state has changed across resume and notify userspace if so.
Fixes "[2.6.24-rc1 regression] AC adapter state does not change after resume"
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not provide /proc/acpi/ac_adapter if ACPI_PROCFS is not defined. This
eliminates duplicated power adapters in HAL and makes it consistent with
battery module
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make 'default_mode' and 'default_var' be __initdata.
Fixes these section warnings:
WARNING: vmlinux.o(.data+0x128e0): Section mismatch: reference to .init.data:default_mode_CRT (between 'default_mode' and 'default_var')
WARNING: vmlinux.o(.data+0x128e4): Section mismatch: reference to .init.data:default_var_CRT (between 'default_var' and 'dev_attr_size')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have seen ramdisk based install systems, where some pages of mapped
libraries and programs were suddendly zeroed under memory pressure. This
should not happen, as the ramdisk avoids freeing its pages by keeping them
dirty all the time.
It turns out that there is a case, where the VM makes a ramdisk page clean,
without telling the ramdisk driver. On memory pressure shrink_zone runs
and it starts to run shrink_active_list. There is a check for
buffer_heads_over_limit, and if true, pagevec_strip is called.
pagevec_strip calls try_to_release_page. If the mapping has no releasepage
callback, try_to_free_buffers is called. try_to_free_buffers has now a
special logic for some file systems to make a dirty page clean, if all
buffers are clean. Thats what happened in our test case.
The simplest solution is to provide a noop-releasepage callback for the
ramdisk driver. This avoids try_to_free_buffers for ramdisk pages.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tle62x0 driver was ignoring all read errors. This patch makes it
pass such errors up the stack, instead of returning bogus data.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"Luming Yu" <luming.yu@gmail.com> says:
There is a "ttyS1 irq is -1" problem observed on tiger4 which cause the
serial port broken.
It is because that there is __no__ ACPI IRQ resource assigned for the
serial port. So the value of the IRQ for the port is never changed since it
got initialized to -1.
If PNP supplies a valid IRQ, use it. Otherwise, leave port.irq == 0, which
means "no IRQ" to the serial core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yu Luming <luming.yu@intel.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i5000_edac driver's PCI registration structure has the name
""i5000_edac"" (with extra set of double-quotes) which is probably not
intentional. Get rid of __stringify.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Firmware like PNPBIOS or ACPI can report the address space consumed by the
RTC. The actual space consumed may be less than the size (RTC_IO_EXTENT)
assumed by the RTC driver.
The PNP core doesn't request resources yet, but I'd like to make it do so.
If/when it does, the RTC_IO_EXTENT request may fail, which prevents the RTC
driver from loading.
Since we only use the RTC index and data registers at RTC_PORT(0) and
RTC_PORT(1), we can fall back to requesting just enough space for those.
If the PNP core requests resources, this results in typical I/O port usage
like this:
0070-0073 : 00:06 <-- PNP device 00:06 responds to 70-73
0070-0071 : rtc <-- RTC driver uses only 70-71
instead of the current:
0070-0077 : rtc <-- RTC_IO_EXTENT == 8
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The misc_register() error path always released an I/O port region,
even if the region was memory-mapped (only mips uses memory-mapped RTC,
as far as I can see).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for version 2 of the ioatdma device. This device handles
the descriptor chain and DCA services slightly differently:
- Instead of moving the dma descriptors between a busy and an idle chain,
this new version uses a single circular chain so that we don't have
rewrite the next_descriptor pointers as we add new requests, and the
device doesn't need to re-read the last descriptor.
- The new device has the DCA tags defined internally instead of needing
them defined statically.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<debug output from Joel's system>
handling stripe 7629696, state=0x14 cnt=1, pd_idx=2 ops=0:0:0
check 5: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800ffcffcc0 written 0000000000000000
check 4: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800fdd4e360 written 0000000000000000
check 3: state 0x1 toread 0000000000000000 read 0000000000000000 write 0000000000000000 written 0000000000000000
check 2: state 0x1 toread 0000000000000000 read 0000000000000000 write 0000000000000000 written 0000000000000000
check 1: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800ff517e40 written 0000000000000000
check 0: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800fd4cae60 written 0000000000000000
locked=4 uptodate=2 to_read=0 to_write=4 failed=0 failed_num=0
for sector 7629696, rmw=0 rcw=0
</debug>
These blocks were prepared to be written out, but were never handled in
ops_run_biodrain(), so they remain locked forever. The operations flags
are all clear which means handle_stripe() thinks nothing else needs to be
done.
This state suggests that the STRIPE_OP_PREXOR bit was sampled 'set' when it
should not have been. This patch cleans up cases where the code looks at
sh->ops.pending when it should be looking at the consistent stack-based
snapshot of the operations flags.
Report from Joel:
Resync done. Patch fix this bug.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Joel Bertrand <joel.bertrand@systella.fr>
Cc: <stable@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove annoying build warnings about unused variables in atmel_serial,
which afflict both AT91 and AVR32 builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a DMA device is unregistered, its reference count is decremented twice
for each channel: Once dma_class_dev_release() and once in
dma_chan_cleanup(). This may result in the DMA device driver's remove()
function completing before all channels have been cleaned up, causing lots
of use-after-free fun.
Fix it by incrementing the device's reference count twice for each
channel during registration.
[dan.j.williams@intel.com: kill unnecessary client refcounting]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move pci_dev_put outside the loops in which it occurs. Within the loop,
pci_dev_put is done implicitly by pci_get_device.
The problem was detected using the following semantic patch, and corrected
by hand.
@@
expression dev;
expression E;
@@
- pci_dev_put(dev)
... when != dev = E
- pci_get_device(...,dev)
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pf driver for parallel port floppy drives seems to be broken. At least
with Imation SuperDisk with EPAT chip, the driver calls pi_connect() and
pi_disconnect after each transferred sector. At least with EPAT, this
operation is very expensive - causes drive recalibration. Thus, transferring
even a single byte (dd if=/dev/pf0 of=/dev/null bs=1 count=1) takes 20
seconds, making the driver useless.
The pf_next_buf() function seems to be broken as it returns 1 always (except
when pf_run is non-zero), causing the loop in do_pf_read_drq (and
do_pf_write_drq) to be executed only once.
The following patch fixes this problem. It also fixes swapped descriptions in
pf_lock() function and removes DBMSG macro, which seems useless.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some error paths in txx9spi_probe wrongly return 0. This patch fixes them by
using the devres interfaces.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After 49dce689ad, device_for_each_child
iteration hits the master device itself. Do not call spi_unregister_device()
for the master device.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zillions of people are getting my-battery-monitor-doesnt-work problems
(including me).
Lessen the damage by making ACPI_PROCFS default to on.
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following is an extra entry to enable the touch screen on the new LG
C1 EXPRESS DUAL machine.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the possible usage of a negative value as an array
index spotted by the Coverity checker.
sisfb_validate_mode() could return a negative error code and we must check for
that prior to using its return value as an array index.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A relatively recent version of the Geode LX datasheet listed the wrong
address for one of the MSRs that controls TFT panels, resulting in
breakage. This patch corrects the MSR address.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Attached patch fixes two compilation problems of s1d13xxxfb.c:
- Fixes outdated dbg() message to fix compilation error with debugging enabled.
- Do not read kernel command line options when compiled as module.
Signed-off-by: Stanislav Brabec <utx@penguin.cz>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instruction pointer returned by profile_pc() can be a random value. This
break the assumption than we can safely set struct op_sample.eip field to a
magic value to signal to the per-cpu buffer reader side special event like
task switch ending up in a segfault in get_task_mm() when profile_pc()
return ~0UL. Fixed by sanitizing the sampled eip and reject/log invalid
eip.
Problem reported by Sami Farin, patch tested by him.
Signed-off-by: Philippe Elie <phil.el@wanadoo.fr>
Tested-by: Sami Farin <safari-kernel@safari.iki.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Variables that are only used in #ifdef CONFIG_X86 should also only be
declared there.
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
chipsfb uses PCI interfaces and should depend on PCI.
CC drivers/video/chipsfb.o
drivers/video/chipsfb.c: In function 'chipsfb_pci_init':
drivers/video/chipsfb.c:378: error: implicit declaration of function 'pci_request_region'
drivers/video/chipsfb.c:435: error: implicit declaration of function 'pci_release_region'
make[2]: *** [drivers/video/chipsfb.o] Error 1
make[1]: *** [drivers/video] Error 2
make: *** [drivers] Error 2
!CONFIG_PCI causes the build to fail.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When PCMCIA_DEBUG is set, cm40x0_cs.c and cm4000_cs.c don't build because the
definition of reader_to_dev uses a non-existent handle field of the struct
pcmcia_device in the call to handle_to_dev. As handle_to_dev works on struct
pcmcia_device, the fix is quite trivial.
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size argument passed to memset is wrong.
Signed-off-by Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size passed to memset is wrong.
Signed-off-by Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the NVRAM on DS1307 and DS1338 chips, like several of the
other drivers do for such combination RTC-and-NVRAM chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several of the RTC drivers are exporting binary "nvram" files in sysfs. Such
NVRAM (or on many systems, EEPROM) data is often initialized during system
manufacture to hold data about identity (serial numbers, Ethernet addresses,
etc), configuration, calibration, and so forth.
This patch improves integrity and security of those files:
- Correctly initializes the size in one of the two cases where
that was not yet being done.
- Improves system security/integrity by making this state not
be world-writable by default.
Letting arbitrary userspace code mangle such state by default is at least Not
A Good Thing; and it could sometimes be worse, depending on the particular
data that might be corrupted. (I disregard the paranoiac "don't let anyone
read it either" approach. Anyone storing passwords in such memory doesn't
really care about security.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Torsten Ertbjerg Rasmussen <tr@newtec.dk>
Cc: Mark Zhan <rongkai.zhan@windriver.com>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC "hctosys" mechanism expects that RTC clock will use UTC, not local
time (e.g. PST). Say so in Kconfig and in the kernel message.
(Strictly speaking, the RTC clock should be tracking the POSIX epoch. That's
not worth going into here. Goofing timezones means clocks are wrong by many
hours; the POSIX-v-UTC differences just cost seconds.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interrupt handler returns IRQ_NONE if it detects that the device
is gone. That's incorrect because the device may have raised the interrupt.
Not acknowledging it may trigger the spurious interrupt detection and kill
drivers sharing the interrupt line.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The validation of the chipset revision was broken
since for rt2500usb and rt73usb different registers
should be read. When rt2500usb was loaded for a rt73
device it would false think the chipset was correct
because the wrong register was read and validated.
This has been fixed by expanding the check to also
see if the first 4 bits of the revision is not-0
(When reading the wrong register offset the returned
value is usually 0 which can be interpreted as invalid)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes association failure (reason = 18) bug by arranging CCK
rates before OFDM rates. This patch will register with mac80211 the
modified rate arrangement with CCK rate first. Change rate scale algorithm
also to deal with rate change. Fix Txpower and rate Table commands to be
constructed correctly after rearrangement.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/isdn/sc/shmem.o
drivers/isdn/sc/shmem.c: In function ‘memcpy_toshmem’:
drivers/isdn/sc/shmem.c:53: warning: passing argument 1 of ‘memcpy_toio’ makes pointer from integer without a cast
Commit 9317d4313e:
ISDN/sc: fix longstanding warning
claimed to fix it, but it didn't.
[ Changed the "void *" to be "void __iomem *" -DaveM ]
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Acked-by:Karsten Keil <kkeilæsuse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
isdn_if.writebuf_skb has an additional ack flag argument which
was missing from sndpkt leading to the following warning:
CC [M] drivers/isdn/sc/init.o
drivers/isdn/sc/init.c: In function ‘sc_init’:
drivers/isdn/sc/init.c:281: warning: assignment from incompatible pointer type
Note that this doesn't actually do anything with the flag, it
just fixes the warning (and probably accessing the last argument).
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If fs_enet is build as module, on PPC_CPM_NEW_BINDING platforms
mii-fec/mii-bitbang should be build as module, as well. On other
platforms, mii-fec/mii-bitbang must be included into the main module.
Otherwise some symbols remain undefined. Additionally, fs_enet uses
libphy, so add a select PHYLIB.
Building modules, stage 2.
MODPOST 5 modules
ERROR: "fs_scc_ops" [drivers/net/fs_enet/fs_enet.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_safe() only protects list from list alterations
performed by the same thread. One still needs to implement
proper locking when list is being accessed from several threads.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If input_register_device() fails input_free_device() must
be called to release memory allocated for the device.
Also consolidate error handling in acpi_bus_video_add()
and handle input_allocate_device() failures.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Properly set up parent on input device registered by the video driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix thinko in commit eaf559bf ("mlx4_core: Don't free special QPs in
QP number bitmap"). The old commit had the logic exactly backwards
and ended up freeing *only* special QPs, which not only left the
original bug in place but also introduced the problem that the QP
number bitmap would get full after a while.
Found by Dotan Barak of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Fixed memory leak by freeing MSI-X local entry memories when vector allocation
fails in s2io_add_isr.
- Added two utility functions remove_msix_isr and remove_inta_isr to eliminate
code duplication.
- Incorporated following review comments from Jeff
- Removed redundant stats->mem_freed and synchronize_irq call
- do_rem_msix_isr is renamed as remove_msix_isr
- do_rem_inta_isr is renamed as remove_inta_isr
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bond_destroy and bond_free_all to not reference the struct
net_device after calling unregister_netdevice.
Bug and offending change reported by Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 32 bits machines but i386 dont have CONFIG_KTIME_SCALAR. On these
machines, ktime.tv64 is more than 4 times the (correct) result given
by ktime_to_ns()
Again on these machines, using ktime_get_real().tv64 >> 6 give a
32bits rollover every 64 seconds, which is not wanted (less than the
120 s MSL)
Using ktime_to_ns() is the portable way to get nsecs from a ktime, and
have correct code.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes no sense to enable interrupts if a device has been unplugged.
In addition if in doubt IRQ_HANDLED should be returned.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii-tool can cause the driver to call msleep during nway reset,
bugzilla.kernel.org bug 8430. Fix by simply calling reinit_locked
outside of the spinlock, which is safe from ethtool, so it should be
safe from here.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by rmk from kautobuild output:
drivers/net/netx-eth.c: In function 'netx_eth_hard_start_xmit':
drivers/net/netx-eth.c:131: error: 'dev' undeclared (first use in this function)
drivers/net/netx-eth.c:131: error: (Each undeclared identifier is reported only once
drivers/net/netx-eth.c:131: error: for each function it appears in.)
drivers/net/netx-eth.c: In function 'netx_eth_receive':
drivers/net/netx-eth.c:158: error: 'dev' undeclared (first use in this function)
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by rmk from kautobuild output:
drivers/net/arm/ep93xx_eth.c:420: error: implicit declaration of function '__netif_rx_schedule_prep'
Signed-off-by: David S. Miller <davem@davemloft.net>
The device attribute max_qp_init_rd_atom is not getting set in cxgb3's
query_device method. Version 1.0.4 of librdmacm now validates the
user's requested initiator and responder resources against the max
supported by the device. Since iw_cxgb3 wasn't setting this attribute
(and it defaulted to 0), all rdma_connect()s fail if there are
initiator resources requested by the app. Fix this by setting the
correct value in iwch_query_device().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPD (inter-packet delay) formula was a little off and assumed a
fixed physical link rate; fix the formula and query the actual
physical link rate, now that we can get it. Also, refactor the
calculation into a common function ehca_calc_ipd() and use that
instead of duplicating code.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Newer firmware versions return physical port information to the
partition, so hand that information to the consumer if it's present.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When an ACK is received, the QP is removed from the timeout list and
then if there are still pending send WQEs, the QP is put back on the
timeout list. It is possible that another post send has put the QP on
the timeout list thus, a check needs to be made before trying to do it
again or the list is corrupted.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When mlx4_buf_free() is called from the error path of
mlx4_buf_alloc(), it may be passed a buffer structure that does not
have all pages filled in. Add a check for NULL to mlx4_buf_free() so
we avoid passing NULL to dma_free_coherent() (which will crash).
Signed-off-by: Ali Ayoub <ali@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix ide-cris, cs5530, sc1200 and sis5513 host drivers to just return instead
of OOPS-ing for unsupported modes in ->set_dma_mode methods.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use drive->select.all for REQ_TYPE_ATA_TASK requests in execute_drive_cmd()
(the obsolete bits 7 and 5 of the Device register need to be set).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We can skip conservative PIO "downgrade" (PIO3 becomes PIO2 etc.) on PMAC.
Problem reported by Mikael.
Cc: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
LILO version 16 was released on 26-02-1995 (sic), so telling people to not use
older versions no longer has any value.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make sure to not clear the other IDE channel's interrupt when clearing an IDE
interrupt via the MRDMODE register.
Thanks to Bart for finding a coding mistake.
Bart:
This fixes regression from commit 66602c83dc
("cmd64x: use interrupt status from MRDMODE register (take 2)").
Extra thanks to Martin for reporting and bisecting the issue.
From: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Martin Rogge <marogge@onlinehome.de>
Tested-by: Milan Kocian <milon@wq.cz>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: (i5k_amb) Convert macros to C functions
hwmon: (w83781d) Add missing curly braces
hwmon: (abituguru3) Identify ABit IP35 Pro as such
hwmon: (f75375s) pwmX_mode sysfs files writable for f75375 variant
hwmon: (f75375s) On n2100 systems, set fans to full speed on boot
hwmon: (f75375s) Allow setting up fans with platform_data
hwmon: (f75375s) Add new style bindings
hwmon: (lm70) Convert semaphore to mutex
hwmon: (applesmc) Add support for Mac Pro 2 x Quad-Core
hwmon: (abituguru3) Add support for 2 new motherboards
hwmon: (ibmpex) Change printk to dev_{info,err} macros
hwmon: (i5k_amb) New memory temperature sensor driver
hwmon: (f75375s) fix pwm mode setting
hwmon: (ibmpex.c) fix NULL dereference
hwmon: (sis5595) Split sis5595_attributes_opt
hwmon: (sis5595) Add individual alarm files
hwmon: (w83627hf) push nr+1 offset into *_REG_FAN macros and simplify
hwmon: (w83627hf) hoist nr-1 offset out of show-store-temp-X
hwmon: Add power meter spec to Documentation/hwmon/sysfs-interface
get_property() should not call battery_update(), it also should call
get_status() only if battery is present to avoid cycle and oops.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Acked-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch reverts Eric's commit 2b008b0a8e
It diets .text & .data section of the kernel if CONFIG_NET_NS is not set.
This is safe after list operations cleanup.
Signed-of-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect length for strncat by replacing it with strlcat
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
With '<=' tick can be incremented up to 26, The last loop is redundant
since even when 'softstate' becomes 'STATE_READY', 'if (tick > 25)'
will still cause the function to return -1,
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.86
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the PHY type reported through ethtool for copper
devices from MII to TP. The latter is more accurate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the A1 revision of 5784, 5764, and 5761, and applies all
previous bugfixes. In places where the list of devices gets too long,
the patch uses a new TG3_FLG3_5761_5784_AX_FIXES flag instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous devices hardcoded the PCI Maximum Read Request Size to 4K. To
better comply with the PCI spec, the hardware now defaults the MRRS to
512 bytes. This will yield poor driver performance if left untouched.
This patch increases the MRRS to 4K on driver initialization.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal hardware timers become inaccurate after link events. Clock
frequency switches performed by the CPMU fail to adjust timer
prescalers. The fix is to detect core clock frequency changes during
link events and adjust the timer prescalers accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most 5784 / 5764 LED modes do not work as expected because of a hardware
bug. This patch forces the LED mode to be in MAC LED mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New CPMU devices contend with the GPHY for power management. The GPHY
autopowerdown feature is enabled by default in the PHY and thus needs to
be disabled after every PHY reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the LINK_SPEED mode to the list of CPMU modes that can
cause the loopback tests to fail. These bugs are planned to be fixed in
future revisions of the chip, so the patch qualifies the fixes as such.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer devices contain bootcode in the chip's private ROM area. This
bootcode is called selfboot. Selfboot can be patched in the device's
NVRAM and the patches can have several formats. In one particular
format, the checksum calculation needs to be slightly modified. This
patch adjusts the NVRAM test code for that case, and add support for the
missing formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
