Use reserve_memtype and free_memtype wrappers for /dev/mem mmaps. The memtype
is slightly complicated here, given that we have to support existing X mappings.
We fallback on UC_MINUS for that.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce phys_mem_access_prot_allowed(), which checks whether the mapping
is possible, without any conflicts and returns success or failure based on that.
phys_mem_access_prot() by itself does not allow failure case. This ability
to return error is needed for PAT where we may have aliasing conflicts.
x86 setup __HAVE_PHYS_MEM_ACCESS_PROT and move x86 specific code out of
/dev/mem into arch specific area.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add xlate and unxlate around /dev/mem read/write. This sets up the mapping
that can be used for /dev/mem read and write without aliasing worries.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Earlier patch that introduced CONFIG_NONPROMISC_DEVMEM, did the
range_is_allowed() check only for read and write. Add range_is_allowed()
check to mmap of /dev/mem as well.
Changes the paramaters of range_is_allowed() to pfn and size to handle
more than 32 bits of physical address on 32 bit arch cleanly.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch introduces a restriction on /dev/mem: Only non-memory can be
read or written unless the newly introduced config option is set.
The X server needs access to /dev/mem for the PCI space, but it doesn't need
access to memory; both the file permissions and SELinux permissions of /dev/mem
just make X effectively super-super powerful. With the exception of the
BIOS area, there's just no valid app that uses /dev/mem on actual memory.
Other popular users of /dev/mem are rootkits and the like.
(note: mmap access of memory via /dev/mem was already not allowed since
a really long time)
People who want to use /dev/mem for kernel debugging can enable the config
option.
The restrictions of this patch have been in the Fedora and RHEL kernels for
at least 4 years without any problems.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Stephen Rothwell noticed that:
Commit 2be621498d ("x86: dma-ops on highmem
fix") in Linus' tree introduced a new warning (noticed in the x86_64
allmodconfig build of linux-next):
drivers/pci/intel-iommu.c:2240: warning: initialization from incompatible pointer type
Which points at an instance of map_single that needs updating.
Fix it to the new prototype.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based addressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.
This code updates the of_serial driver to handle the reg-offset
and reg-shift properties to enable this core to be used.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (452 commits)
V4L/DVB (7731): tuner-xc2028: fix signal strength calculus
V4L/DVB (7730): tuner-xc2028: Fix SCODE load for MTS firmwares
V4L/DVB (7729): Fix VIDIOCGAP corruption in ivtv
V4L/DVB (7728): tea5761: bugzilla #10462: tea5761 autodetection code were broken
V4L/DVB (7726): cx23885: Enable cx23417 support on the HVR1800
V4L/DVB (7725): cx23885: Add generic cx23417 hardware encoder support
V4L/DVB (7723): pvrusb2: Clean up input selection list generation in V4L interface
V4L/DVB (7722): pvrusb2: Implement FM radio support for Gotview USB2.0 DVD 2
V4L/DVB (7721): pvrusb2: Restructure cx23416 firmware loading to have a common exit point
V4L/DVB (7720): pvrusb2: Fix bad error code on cx23416 firmware load failure
V4L/DVB (7719): pvrusb2: Implement input selection enforcement
V4L/DVB (7718): pvrusb2-dvb: update Kbuild selections
V4L/DVB (7717): pvrusb2-dvb: add DVB-T support for Hauppauge pvrusb2 model 73xxx
V4L/DVB (7716): pvrusb2: clean up global functions
V4L/DVB (7715): pvrusb2: Clean out all use of __FUNCTION__
V4L/DVB (7714): pvrusb2: Fix hang on module removal
V4L/DVB (7713): pvrusb2: Implement cleaner DVB kernel thread shutdown
V4L/DVB (7712): pvrusb2: Close connect/disconnect race
V4L/DVB (7711): pvrusb2: Fix race on module unload
V4L/DVB (7710): pvrusb2: Implement critical digital streaming quirk for onair devices
...
The UCB1400 driver IRQ probe code fails to find an interrupt if all
the interrupts in the range 0-31 are nonprobe-able. This patch
removes the check of the return value so interrupts above 31 can be
detected.
Tested on InHand Fingertip4 PXA270 board.
Signed-off-by: Vernon Sauder <vsauder@inhand.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The mouse button emulation calls input device methods from an input
device. This causes funny lock nesting which is harmless as each
device has its own locks.
Give the nesting device its own lock classes so that lockdep will not
consider them the same.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix incorrect length argument for strncpy and strncat by replacing them with
strlcpy and strlcat
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since 43cc71eed1, the platform modalias
is prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable
"input" platform drivers, to re-enable auto loading.
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are different tables for MTS firmwares. This should be taken into
account while selecting the proper firmware.
While at tuner-xc2028.h, improve some comments.
Thanks to Edward J. Sheldrake <ejs1920@yahoo.co.uk> for helping to
diagnose such troubles with PAL/I standard.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frank Bennett reported that ivtv was causing skype to crash. With help
from one of their developers he showed it was a kernel problem.
VIDIOCGCAP copies a name into a fixed length buffer - ivtv uses names
that are too long and does not truncate them so corrupts a few bytes of
the app data area.
Possibly the names also want trimming but for now this should fix the
corruption case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx23885: Enable cx23417 support on the HVR1800
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change how list of possible pvrusb2 inputs is generated to include
only those interfaces that make sense for the interface instance.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These changes are required with the addition of digital television support
for the Hauppauge HVR1900 & HVR1950, the OnAir Creator and Sasem USB HDTV
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following cleanups:
- make the following needlessly global function static:
- pvr2_hdw_set_cur_freq()
- #if 0 the following unused global functions:
- pvr2_hdw_get_state_name()
- pvr2_hdw_get_debug_info_unlocked()
- pvr2_hdw_get_debug_info_locked()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently the kernel developers no longer consider it proper
etiquette to use __FUNCTION__; everyone must instead use __func__
(even though it breaks with older compilers). And worse still, actual
effort is being expended to sweep this change throughout the kernel
source tree. Don't these people have better things to do? So...
Completely clean out all use of __FUNCTION__ from the pvrusb2 driver
(it was just in the sysfs interface). I'm not going to use __func__
either. So there.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver was getting had by this scenario:
1. Task A calls kthread_stop() for task B.
2. Before exiting, then Task B calls kthread_stop() for task C.
The problem is, kthread_stop() wants to allocate an internal resource
to itself (i.e. acquire a lock), which won't be released until
kthread_stop() returns. But kthread_stop() won't return until task B
is dead. But task B won't die until it finishes its call to
kthread_stop() for task C, and that will block waiting on the resource
already allocated inside task A. Deadlock.
With the pvrusb2 driver, task A is the caller to pvr_exit(), task B is
the control thread run inside of pvrusb2-context.c, and task C is any
worker thread run inside of pvrusb2-hdw.c.
This problem got introduced by the previous threading setup change,
which was itself an attempt to fix a module tear-down race (which it
actually did fix). The lesson here is that a task being waited on as
part of a kthread_stop() simply cannot be allow to also issue a
kthread_stop() - or we make sure not to issue the enclosing
kthread_stop() until we know that the inner kthread_stop() has
completed first. The solution for the pvrusb2 driver is some hackish
code which changes the main control thread tear down into a two step
process. This then makes it possible to delay issuing the
kthread_stop() on the control thread until after we know that
everything has been torn down first. (And yes, we really need that
kthread_stop() because it's the only way to safely guarantee that a
module-referencing kernel thread has safely returned back out of the
module before we finally remove the module.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Earlier fix to handle DVB feed thread aborts was overly-aggressive.
We can take better advantage of what kthread_stop() can do. This
change simplifies things.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If a disconnect happens before initialization is completed, the
pvrusb2 driver can accidentally touch dangling pointers. The whole
initialization function must be protected by the big_lock, and once
inside that lock, the initialization function should abort if it is
discovered that a disconnect has already taken place.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver - for basically forever - was not enforcing a
proper module tear-down. Kernel threads are used inside the driver
and all must be gone before the module can be safely removed. This
changeset reimplements a chunk of pvrusb2-context.c to enforce this
correctly. Unfortunately this is not a simple fix. The new
implementation also cuts back on kernel thread usage; instead of there
being 1 control thread per instance now it's just 1 control thread
shared by all instances. (By dropping to a single thread then the
module exit function can block on its shutdown and the thread itself
can monitor and cleanly shut down all of the other instances first.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement timed measurement of encoder operation for the first time it
is run. This allows the driver to note when the encoder has been run
successfully for at least 1/4 second. On top of that implement
various bits to ensure that the encoder has been run once before
digital streaming for OnAir devices. This is done via several core
state machine tweaks.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some tuners seem to not work in digital mode unless the encoder is
healthy. Implement a device attribute to represent this flag and
modify the core state machines to enforce this requirement.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the device fails to stream, the feed thread will block forever
waiting for buffers. But while in this state it was not looking for
an exit condition from the driver DVB interface. This caused the
thread to jam. Implement a new stop flag (which will be set
appropriately) to tell the thread to stop.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the DVB interface is not compiled, the pvr2_dvb_props struct is
not available - so it really should be ifdef'ed out as well. This
didn't cause an error because in this context its usage was as an
opaque pointer. But it really shouldn't be present at all if DVB is
not enabled.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The commands to start / stop USB streaming for an analog device are
fairly standard, owing to the fact that all supported devices
apparently started from the same common reference design. However
with digital mode, the commands seem to vary by vendor. This change
makes that variance more explicit. It also cleans up a related
problem for OnAir devices which prevented digital mode from working at
all.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Numerous places in the driver need to issue simple commands to the FX2
microcontroller (e.g. only 1 or 2 bytes, no reply needed). Previously
each place that did this, had to take lock, set up a central buffer,
and call the function to perform the handshake. This change puts
these steps into a single spot. This also has the effect of removing
the need to mess with the control lock from numerous places in the
code.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement a mechanism in the pvrusb2 driver for gathering statistics
on the stream buffering, including bytes transferred, buffers handled,
buffers in flight, etc. This is useful for debugging certain classes
of streaming issues and for determining if the buffer pool size is
generally correct for the driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Don't trigger a pathway state change if it's already been triggered
(eliminates some wasted processing and some debug output noise)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move pvr2_dvb_adapter usage out of the pvrusb2 driver core - it's
really private to the pvrusb2-dvb module and nothing outside of the
dvb implementation should care about it. Creation / destruction of
the pvr2_dvb_adapter instance is now contained entirely within
pvrusb2-dvb.c.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the end we'd like the dvb interface to always be present - even for
analog devices (via the mpeg encoder). However right now pvrusb2-dvb
won't operate correctly if the hardware doesn't have a digital tuner,
so don't initialize the DVB interface unless we know we have a digital
tuner.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Other pvrusb2-dvb changes have made the digital_up flag obsolete. So
kill it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than making an explicit call to tear down the pvrusb2-dvb
module, use the callback in the pvr2_channel structure. This has the
advantage that now tear-down only happens when it makes sense. The
previous implementation had scenarios where it was possible for the
tear-down call to happen without a prior initialization.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Eliminate the need for a separate pvr2_dvb_fh; since in the DVB
context there can only ever be a single instance then there is no need
for a separate instance to handle streaming state. This simplifies
the module. Also move streaming start/stop out of the feed thread and
into the driver's main context - which makes it possible for streaming
start up failures to be detected by the DVB core.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2-dvb feed thread cannot be allowed to exit by itself
without first waiting for kthread_should_stop() to return true.
Otherwise the driver will have a dangling task_struct context, which
will cause a very nasty kernel oops.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
start work on streaming / buffer handling code to feed the software demux
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This function is just a skeleton for now -
a placeholder to remind us to fix it.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add basic framework for the DVB API. This is enough to control the
tuner & demod of the digital frontend, but the stream & buffer handling
is still missing.
Additional note from Mike Isely <isely@pobox.com> - also, since these
changes are still very experimental arrange for DVB changes to be
compiled in via new CONFIG_VIDEO_PVRUSB2_DVB option, for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are two conditions, reported by saa7134 that indicates that the I2C bus
is busy: TO_SCL and TO_ARB.
On both states, it needs to wait for I2C release, before using the bus.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
DVB-T mode is now supported using the DiBcom dib7000p demodulator
and the Xceive xc3028L silicon tuner. Analog mode is not supported.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This allows future drivers to select the most appropriate output mode.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the pxa-camera driver has a bug, visible when the user requests
more than 2 video buffers. When the third buffer is queued, it is not
appended to the DMA-descriptor list of the second buffer, but is again
appended to the first buffer. Fix it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
FIFO overruns are not seldom on PXA camera interface FIFOs. Handle them by
dropping the corrupted frame, waiting for the next start-of-frame, and
restarting capture.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for YUV packed and planar capture for pxa_camera.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This obviously redundant return has been in the driver from the very first
version. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert meye to use video_ioctl2
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Activy budget card with BSBE1 tuner, subsystem id 0x1131:0x4f60.
Low band and DiSEqC support should work now (BSBE1 and BSRU6 tuner).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reworked the BSBE1 tuner support in bsbe1.h to follow
the ALPS-recommended parameters more closely.
Tested with BSBE1-based Activy cards and TT DVB-S rev 2.3.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implementation of DMX_SET_BUFFER_SIZE for dvr.
Synchronization of the code of DMX_SET_BUFFER_SIZE for demux and dvr.
Signed-off-by: Andrea Odetti <mariofutire@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the bug in DMX_SET_BUFFER_SIZE for the demux.
Basically it resets read and write pointers to 0 in case they are
beyond the new size of the buffer.
Signed-off-by: Andrea Odetti <mariofutire@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the tuner work with transonders providing higher
symbol rates.
It was contributed by Oliver Endriss.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch replaces the c++ style comments.
No functional changes
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some DVB-S boards, i.e. with the SD1878 tuner, use a 4 MHz reference frequency.
This reqires a different setup of the clock PLL.
This patch adds an enum to the tda10086_config struct and sets the proper
values for the boards.
This patch also fixes the DVB-S section of the MD7134_BRIDGE_2
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tuner-xc2028.c
- Drop the severity level of the xc3028 version reporting, since it's
only of interest to developers and user's don't need to have it show up
in their dmesg output every time they change the channel.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-core.c
- Drop the severity level of the "urb resubmit failed" to debug, since it
occurs every time a stream disconnects, which fills the dmesg log
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes several issues on SCODE:
1) The extracting tool weren't generating the proper tags for SCODE. This
has almost no effect, since those tags shouldn't be used;
2) DIBCOM52 were using a wrong IF. It should be 5200, instead of 5700;
3) seek_firmware were wanting an exact match for firmware type. This is
wrong. As result, no SCODE firmware were loaded;
4) A few files were including the wrong file for seeking demod firmwares;
5) XC3028_FE_DEFAULT can be used, if user doesn't want to load a firmware.
However, this weren't documentated. This feature require more testing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For boards that require the avcore (cx25840) to be active, ensure
it gets loaded.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for DVB-T mode only, analog is not supported.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx25840: Ensure GPIO2 is correctly set for cx23885/7/8 based products.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for DVB-T mode only, analog mode is not supported.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding support for the NXP TDA10048HN DVB OFDM demodulator
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The current code creates a bogus DEVPATH:
/devices/pci0000:00/0000:00:1d.0/usb1/1-2/video4linux/video0
while it should be:
/devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.0/video4linux/video0
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
consolidate au8522_qam256_mse2snr_lookup, au8522_qam64_mse2snr_lookup and
au8522_vsb_mse2snr_lookup into a single function, au8522_mse2snr_lookup.
Pass the mse2snr table into au8522_mse2snr_lookup depending on the
modulation type.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add function au8522_read_mse, which will be used to compute snr
TO DO: mse2snr
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ucblocks are reported in separate registers for vsb & qam
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_AU0828 should select DVB_AU8522 and DVB_TUNER_XC5000 if !DVB_FE_CUSTOMIZE
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Avoid an oops if the board is not fully defined.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Including support for the AU0828 USB Bridge.
Including support for the AU8522 ATSC/QAM Demodulator.
Including support for the AU8522 ATSC/QAM Demodulator.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver should be switched to digital mode, when trying to access the
frontend or when streaming.
This patch provides the correct code to support this feature.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before this patch, HVR900/HVR950 were incorreclty going back to analog. The
result is that only digital were working.
This patch provides the proper setup for analog/digital and tuner callback.
It also properly resets analog into a sane state at open().
Thanks to Steven Toth <stoth@linuxtv.org> and Michael Krufky <mkrufky@linuxtv.org>
for helping to set the proper parameters to GPO/GPIO em2883 ports.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, all registers will follow the same convension:
EM28XX_R<reg_number>_<reg_name>
This allows to associate a register with its value, and also with a canonical
name. Also, registers that are specific to a given chip were renamed accordingly,
as EM2800_foo (for 2800 only registers) or EM2880_foo (for registers that started
to appear on em2880).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before this patch, registers 0x04 and 0x08 were referenced by its value. This is
bad, since makes harder for someone to understand what this is doing.
This patch renames those two registers into an appropriate name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx.h contains lots of different stuff inside. The better is to break it on
some files.
This patch removes the register names, moving them to a separate file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is more conservative than just removing the msleep() from
em28xx_write_regs_req(), since some old hardware may still need it.
So, it will remove the sleep time only for those chips where this
removal were tested.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-core.c:
- Remove sleep in i2c message routine which slows down i2c by a factor
10x. Load time for BASE firmware went from 13s to .973s
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-dvb.c:
- Remove unneeded xc3028_ctrl structure. The driver automatically preserves
the previous value
tuner-xc2028.c:
- Make the return type for xc2028_get_reg signed, since all of the callers
are looking for "< 0" to detect errors.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
xc3028_sleep function is being used with a different meaning. This
should be called only before doing S1/S3 sleep.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Modifies em28xx-dvb not to use videobuf-dvb, but instead to include the code
for registering dvb devices locally and use the URB management code in the
em28xx driver directly. DVB data streaming should now work.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move the URB setup and management code to em28xx-core.c and generalise
it slighlty so that the DVB code can use it.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c:
- Fix reversed val/rst values in both analog_gpio and digital_gpio
vectors
- Fix crash that would was occurring during every analog startup
while looping over gpio_ctl
- Remove what appears to be a redundant setting of gpio_ctl->val
- Don't use OREN538 demodulation for the HVR-950 (prevents ATSC
scanning from working)
em28xx-dvb.c:
- Tuner should be in digital mode when issuing the reset
- Add copyright
- Change struct definition (corresponds to fix in em28xx-cards.c for
gpio_ctl looping)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Devin Heitmueller <devin.heitmueller@gmail.com> and Aidan
Thornton" <makosoft@googlemail.com> for pointing some errors with the
previous scenario.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds DVB support for Hauppauge HVR950.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for getting those values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx based devices with xc3028 may require some specific gpio values.
This patch adds a generic handling for such values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds em28xx-dvb. This driver is highly based on cx88-dvb and
saa7134-dvb.
This code currently loads and unloads successfully. However, some
changes are needed to properly support the mpeg streams and to setup
em28xx to work on DVB mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@ change_compare_np @
expression E;
@@
(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)
@ include depends on change_compare_np @
@@
@ no_include depends on !include && change_compare_np @
@@
#include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The patch extends the default keymap of FlyVIdeo2000 IR remote control so that
this remote may also serve movie & music players in a better way.
I bought a SAA7130 TV tuner with a remote control having 3 additional button
as the default layout, exactly as:
1) labeled "<<<" : key code 0x19, may be used as "backward"in MPlayer,XMMS etc
2) labeled ">>>" : key code 0x1f, may be used as "forward"...
3) not labeled : key code 0x0a, may be used as "pause"...
Once have added these code definitions to the kernel, me got all these
operations available for viewing movies & listening music.
Signed-off-by : Ivan Bobyr <brefi@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch modifies Dmitri's original ibmcam driver for Linux to improve
support for the IBM PC Camera Pro. It may also offer improved support for
other models classified by the driver as 'Model 3', such as the IBM PC Camera
Pro Max.
See http://auricle.dyndns.org/xvp610/
Signed-off-by: David Hilvert <dhilvert@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes zoran checks for VIDEO_V4L2, since this API is always
present, when V4L is selected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Observation one: ->write_proc and ->data assignments aren't needed. Removed.
Observation two: codecs lists are unprotected. Patch doesn't fix this.
Observation three:
/proc/videocodecs printout is done to temporary _global_ buffer which
is freed in between. Consequently, two users hitting this file can
screwup each other.
Steps to reproduce:
modprobe videocodec
while true; do cat /proc/videocodecs &>/dev/null; done &
while true; do cat /proc/videocodecs &>/dev/null; done &
The fix is switching to seq_files, this removes code, especially some
line-length "logic".
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the leak of the bttv_fh structure allocated in radio_open which
was introduced by commit 5cd3955cb8.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to the patch order change, pvrusb2 were broken. So, changeset
4c3b01f711 were applied at mainstream to fix.
After the pvrusb2 changes, this patch is no longer required and should be
reverted.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patches adds support for the SkyStar2 rev2.7 with the PN1010/ITD1000 Frontend.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support is prepared, but the CX24113-driver .c-file is missing. After sorting out the NDA problems, the file will be there immediatly.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a setting to config struct for inversion of lnb-voltage.
Needed for support of Avermedia A700 cards.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Do not hardcode xtal frequency but allow different values
for future zl10313 support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correct the frequency of the emitted diseqc signal to 22kHz.
Adds sleep(100) to wait for message to be transmitted.
For now the only user of mt312 is b2c2-flexcop, and it
does overwrite all diseqc related functions with own code.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change type of buffer variables from void* to u8* to save some casts.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This device is a clone of the PN1010 used by SkyStar2 rev2.7 .
This patch adds support for the flexcop-device and makes the driver look a little bit nicer.
It needs to be checked whether the driver is still ok for the budget-cards.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removes some fields from data structs.
There are some fields that are just caching some calculus for buffer
size. The calculus were moved to the places it were needed and the now
unused fields were removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf-dvb were still using a function that were videobuf-dma-sg
dependent. This patch creates a generic handler for this function. This
way, videobuf-dvb can now work with all videobuf implementations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes three related issues and a fourth trivial one:
- Use buffers even if no-one's currently waiting for them (fixes
underrun issues);
- Don't return incomplete/mangled frames at the start of streaming and
in the case of buffer underruns;
- Fix an issue which could cause the driver to write to a buffer that's
been freed after videobuf_queue_cancel is called (exposed by the
previous two fixes - for some reason, ignoring buffers that weren't
being waited on worked around the issue);
- Fix a bug which could cause only one field to be filled in the first
buffer (or first few buffers) after streaming is started.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are some cases where nobody is waiting for a buffer. Due to the
lack of check, if you try to abort the userspace app, machine were
hanging, since IRQ were trying to use a buffer that were disallocated.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A spinlock is necessary for queue_cancel to work with every driver in the tree.
Otherwise a race exists between IRQ handlers removing buffers from the queue
and queue_cancel invalidating the queue.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before the patch, there were a risk of freeing and unmapping userspace memory,
while there were pending requests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, vidioc_s_fmt_cap is allowed even if streaming is running on some
other fh. This is likely to cause issues.
Block use of vidioc_s_fmt_cap if someone else has claimed access to the device.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were a small bug on videobuf-vmalloc that were preventing STREAMOFF to
work. The issue is that vmalloc'ed mmaped memory should only be freed after
being sure that there aren't any mmap usage. Otherwise, the memory remap will
stop working, and the userspace won't receive any frames.
This bug were affecting some userspace applications, like tvtime.
After this patch, tvtime started to work again with the drivers that use
videobuf-vmalloc.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were some bugs on videobuf-vmalloc.
Basically, remap were called with a wrong parameter. Due to that, a later remap
were needed, generating the need of some hacks on videobuf-vmalloc and
videobuf-core.
This patch fixes the remap and removes the hacks.
TODO:
- V4L2_MEMORY_USERPTR is not implemented yet. This method should be
properly implemented, in order to work with a few userspace applications.
- The driver also doesn't implement V4L2_MEMORY_OVERLAY. This method is used
only by a few applications, and are becaming obsolete, due to the increment
of cpu performance. So, most apps prefer to retrieve data to an internal
buffer, doing some processing like de-interlacing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I did notice a possible memory leak since iolock is could possibly be
called before a buffer has been freed.
This ensure s_fmt isn't called while the queue is busy thereby avoiding
iolock on already allocated buffers.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove dead code;
- Fix a few CodingStyle issues;
- Prints frame number, if debug is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Aborting buffer_filled if no-one's waiting on the waitqueue probably isn't
what we want, since just because no-one's waiting for it now doesn't mean they
wouldn't dequeue it in time. (vivi gets away with this, possibly because it
can fill each buffer much faster.)
- The first BUG_ON(lencopy <= 0); really isn't worth causing a kernel panic
over, especially since there are some reasons why it could trigger in normal use.
- The top and botom frames are actually the wrong way around.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The last videobuf changes introduced several CodingStyle errors. Fixes all those
errors, as reported by checkpatch.pl
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It fixes a couple of minor bugs, comments out a bogus BUG_ON, sets fh->type
correctly, uses dev->width and dev->height for now, and adds a missing spinlock
init (nasty - caused a system lockup). It also adds some debug code which
probably isn't all that useful. I haven't tested this version of the patch yet,
though, so I'm not sure what you can expect if you try it.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The usage of videobuf-vmalloc allows to cleanup em28xx logic.
Also, it reduced its size by about 5.42% on i386 arch (and about 7.5% on x86_64):
39113 4876 40 44029 abfd old/em28xx.ko
36731 4868 40 41639 a2a7 /home/v4l/master/v4l/em28xx.ko
Also, the preliminary tests, made on a single core 1.5 MHz Centrino showed
that CPU usage reduced from 42%-75% to 28%-33% (reports from "top") command.
A test with time command presented an even better result:
This is the performance tests I did, running code_example to get 1,000 frames
@29.995 Hz (about 35 seconds of stream), tested on a i386 machine, running at
1,5GHz:
The old driver:
$ time -f "%E: %Us User time, %Ss Kernel time, %P CPU used" ./capture_example
0:34.21: 8.22s User time, 25.16s Kernel time, 97% CPU used
The videobuf-based driver:
$ time -f "%E: %Us User time, %Ss Kernel time, %P CPU used" ./capture_example
0:35.36: 0.01s User time, 0.05s Kernel time, 0% CPU used
Conclusion:
The time consumption to receive the stream where reduced from about 33.38
seconds to 0.05 seconds.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The adapter_nr module options can be used to allocate static adapter
numbers on a driver level. It avoids problems with changing DVB apapter
numbers after warm/cold boot or device unplugging and repluging.
Each driver holds DVB_MAX_ADAPTER long array of the preferred order of
adapter numbers.
options dvb-usb-dib0700 adapter_nr=7,6,5,4,3,2,1,0 would result in a
reversed allocation of adapter numbers.
With adapter_nr=2,5 it tries first to get adapter number 2 and 5. If
both are already in use it will allocate the lowest free adapter number.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be>
Acked-by: Hermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If frontend is not attached, both cx88-dvb and saa7134-dvb don't
register DVB. However, dvb unregister were inconditionally called.
Due to that, an OOPS is generated.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added the last remaining out-of-tree kernel driver from the ivtv project.
The saa717x is used in several Japanese cards and a Russian card. The
driver is not complete in that only NTSC is supported and no PAL/SECAM.
Hopefully this will be added in the future.
Signed-off-by: Takahiro Adachi <tadachi@tadachi-net.com>
Signed-off-by: Kyuma Ohta <whatisthis@jcom.home.ne.jp>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement support for Fujitsu Siemens DVB-T Activy Budget, sub-system id 0x1131:0x5f61.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Quoting the commit introducing reinitialise_demod (3984 / by adq):
"These cards [KNC1 DVBT and DVBC] need special handling for CI - reinitialising the frontend
device when the CI module is reset."
Apparently my 1894:0010 also needs that fix, because once you initialise CI/CAM you lose lock.
Signed-off-by: Christoph Pfister <pfister@linuxtv.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The current ci implementation doesn't accept 0xff when reading data bytes (address == 0),
thus breaks cams which report a buffer size of 0x--ff like my orion one.
Remove the 0xff check altogether, because validation is really the job of a higher layer.
Signed-off-by: Christoph Pfister <pfister@linuxtv.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for composite and s-video inputs on
Avermedia DVB-S Pro and DVB-S Hybrid+FM cards
(both labled A700) to the saa7134 driver.
XC2028 support for Hybrid+FM is still missing.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Hermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch adds complete remote control support for Powercolor Real
Angel 330.
Signed-off-by: Daniel Fraga <fragabr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch fixes gpio references for Powercolor Real Angel 330.
Signed-off-by: Daniel Fraga <fragabr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__PRETTY_FUNCTION__ has no sense in C lang context. Rename it as __func__
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All drivers should provide a spinlock to be used in videobuf operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Reviewed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Function pointers and the driver owner are not expected to change
throughout soc-camera host's life. Extract them into an operations struct.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a waitqueue to wait on when there are no buffers in the buffer queue.
DQBUF waits on this queue without holding vb_lock to allow a QBUF to happen.
Once a buffer has been queued we recheck that the queue is still streaming and
wait on the new buffer's waitqueue while holding the vb_lock. The driver
should come along in a timely manner and put the buffer into its next state
finishing the DQBUF.
By implementing this waitqueue it also brings the videobuf DQBUF up to spec and
it now blocks on O_NONBLOCK even when no buffers have been queued via QBUF:
"By default VIDIOC_DQBUF blocks when no buffer is in the outgoing queue."
- V4L2 spec
Signed-off-by: Brandon Philips <bphilips@suse.de>
CC: Trent Piepho <xyzzy@speakeasy.org>
CC: Carl Karsten <carl@personnelware.com>
CC: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
vivi previously had a very complex queuing system and held spinlocks while
doing copy_to_user, kmalloc, etc. This caused the driver to easily deadlock
when a multi-threaded application used it and revealed bugs in videobuf too.
This replaces the copy_to_user with memcpy since we were never copying to user
space addresses. And makes the kmalloc atomic.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
vivi currently doesn't have the infrastructure to handle being opened more than
one time and will crash if it is. So, make it openable only once.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the buf_release on vm_close because it will lead to a buffer being
released multiple times since all buffers are already freed under the two
possible cases: device close or STREAMOFF.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The waitqueues must be woken up every time state changes.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tuner-simple is the only module that uses tuner-types - these will be
merged to a single module in the future. For now, build both of them
if TUNER_SIMPLE is selected.
This fixes the following build warning, if tuner-simple is selected
without tuner-types:
WARNING: "tuner_count" [tuner-simple.ko] undefined!
WARNING: "tuners" [tuner-simple.ko] undefined!
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Show IF level and rf agc top settings in standard map dumps.
Dump standard map during attach if DBG_MAP or DBG_ADV is set.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the needlessly global sn9c102_i2c_try_write() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
CC: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a proper prototype for zr36016_write() in
drivers/media/video/zoran_card.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Detect Leadtek Winfast USB DTV Dongle with ID of 0x6f01
Signed-off-by: Darryl Green <darryl.green@aanet.com.au>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Alexander Simon found out that the Terratec Cinergy T USB XXS is just a clone of another DiB7070P-based device.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch enables support for repeating last event when a key is holded
down with dib0700 devices. It works with rc5 and nec remotes.
It also fixes an annoying bug that floods kernel log with "Unknown key"
messages after each keypress. This happened because the driver was not
resetting infrared register after each poll so it kept polling last key
even if nothing was being pressed. Fixing this, (calling rc_setup after
each poll), permits to implement key repeat.
Signed-off-by: Filippo Argiolas <filippo.argiolas at gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for Technotrend connect S-2400.
Signed-off-by: Andre Weidemann <Andre.Weidemann@web.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To support a new device based on CX24123 (using the CX24113-tuner) the following was done:
- added two parameters to de-select the internal PLL-driver (for CX24108) and a AGC-function callback.
- added a virtual i2c-adapter which allow simple access behind the i2c-gate
- cleanup up some code
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To prepare the support for new device to the flexcop-family some preparation and cleanups was done + some saneness:
- created an i2c-adapter for each i2c-port available. Easier usage for devices with several device on different i2c-busses
- initialize i2c before doing the eeprom read
- changed the way to attach the different frontends, easier to read now
- enabled support for i2c-devices having no register address (1-byte access)
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An enabled color killer will not degrade picture quality for color
input signals, only suppress bogus color information on
black-and-white input. Therefore enable it by default.
Signed-off-by: Frej Drejhammar <frej.drejhammar@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to timf <timf@iinet.net.au>, "Richard (MQ)" <osl2008@googlemail.com> and
gian luca rasponi <lucarasp@inwind.it> for their tests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx2388x family has a color killer. This patch implements the
V4L2_CID_COLOR_KILLER control for the cx2388x family. By default the
color killer is disabled, as in previous versions of the driver.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An enabled chroma AGC will not degrade picture quality if enabled on a
color PAL or NTSC signal with nominal signal levels. It will give a
significant color reproduction improvement if the chroma signals
diverge from nominal levels. Therefore enable chroma AGC by default
for PAL and NTSC standards.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx2388x family has support for chroma AGC. This patch implements a
the V4L2_CID_CHROMA_AGC control for the cx2388x family. By default
chroma AGC is disabled, as in previous versions of the driver.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the IR worker is not stopped before the removal of the cx88xx module,
an OOPS may occur, because the worker function cx88_ir_work gets called.
So stop the ir worker.
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This board has a s5h1409 demod, plus a xc30x8 tuner (probably, xc3018).
This patch adds proper support for radio, video, s-video, composite and ATSC.
However, support for radio and video depends on having s5h1409 i2c gate open,
otherwise, xc30x8 chip won't be visible.
For a better support, some rework is needed on cx88 driver, to allow adding
xc30x8 to i2c bus without sending i2c 0 byte reading to 0xc2 address.
Thanks to Vanessa Ezekowitz <vanessaezekowitz@gmail.com> for helping to figure
out the proper parameters for s5h1409 and the GPIO pins used by each
configuration.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix use of a non-int (size_t) being passed in a printf width field.
This benign issue has apparently been around for a long time, but went
undetected until now.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update Kconfig for the hybrid devices recently converted
to use tuner-simple rather than dvb-pll.
dvb-bt8xx no longer uses dvb-pll at all, so remove all
references to dvb-pll within that driver.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following build error:
In file included from dvb-bt8xx.c:35:
dvb-bt8xx.h:42:26: error: tuner-simple.h: No such file or directory
dvb-bt8xx.c: In function 'frontend_init':
dvb-bt8xx.c:612: error: 'simple_tuner_attach' undeclared (first use in this function)
dvb-bt8xx.c:612: error: (Each undeclared identifier is reported only once
dvb-bt8xx.c:612: error: for each function it appears in.)
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of '__a'
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:612: warning: cast from pointer to integer of different size
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:612: warning: cast from pointer to integer of different size
dvb-bt8xx.c:612: error: called object '__a' is not a function
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of '__a'
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:696: warning: cast from pointer to integer of different size
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:696: warning: cast from pointer to integer of different size
dvb-bt8xx.c:696: error: called object '__a' is not a function
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are a number of different firmware versions and variants, shipped
together with boards.
This patch adds an extra parameter to the tuner-xc2028 to allow specifying for
an specific firmware name to be loaded. This helps to test for a firmware that
better fits some board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Force the main pll charge pump or cal pll charge pump to source current
to the main pll loop filter or cal pll loop filter, respectively.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Set rfagc to high speed mode before setting the pll.
Set rfagc to normal speed mode at the end of the function.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
allow device-specific configuration of rf agc rf top and if top
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The internal calibration signal must be set on the cal pll.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Both the tda18271 c1 and c2 parts only need EP3 through MD3 to be written for
the image rejection calibration's low band initialization.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ability to select RF input was a supported feature only available on
Philips TUV1236d and Philips FCV1236d.
This feature, along with support for the tuners that used it,
was moved into the tuner-simple module.
This can now be removed from dvb-pll.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
remove #if 0'd support for:
Philips TUV1236D
Philips TD1316
Philips FMD1216ME
LG TDVS-H06xF
Philips FCV1236D
Thomson FE6600
Microtune 4042 FI5
Thomson dtt761x
Support for these tuners has been moved into the 'tuner-simple' module.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb and saa7134-dvb to use tuner-simple instead of dvb-pll
for Philips TUV1236D
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert saa7134-dvb to use tuner-simple instead of dvb-pll for Philips TD1316
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cxusb, cx88-dvb and saa7134-dvb to use tuner-simple instead of
dvb-pll for Philips FMD1216ME
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb, dvb-bt8xx, b2c2-flexcop, cxusb and cx23885 to use
tuner-simple instead of dvb-pll for LG TDVS-H06xF
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert dvb-bt8xx to use tuner-simple instead of dvb-pll for Philips FCV1236D
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb to use tuner-simple instead of dvb-pll for Thomson FE6600
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb to use tuner-simple instead of dvb-pll for Microtune 4042 FI5
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert cx88-dvb to use tuner-simple instead of dvb-pll for Thomson DTT 761X
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add module options to tuner-simple, called "atv_input" and "dtv_input"
to specify which rf input to use on devices with multiple rf inputs.
If the module option is not specified, then the driver will autoselect
the rf input, as per previous behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes several kernel oops, when unplugging device while it is in
use:
Basically the patch delays freeing of the internal variables in
si470x_usb_driver_disconnect, until the the last user closed the device in
si470x_fops_release. This was implemented a while ago with the help of Oliver
Neukum.
I tested the patch five times (unplugging while in use) without oops coming
from the radio-si470x driver anymore. A remaining oops was coming from the
usbaudio driver, but this is someone else task. Hopefully this fixed all
unplugging issues.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The video_dev parameter, on tuner-xc2028 were used to pass i2c private data to
tuner_callback. Since the driver already have a pointer to i2c_adap->algo_data,
uses this instead.
This parameter were used also as a magic number to idenfity if two drivers are
trying to register the same xc3028 tuner. This occurs with boards with DVB
support, where both DVB and V4L drivers will share the same tuner.
Instead of using the algo_data as a private number, after this patch, the
driver will use i2c_adap->dev, with seems more consistent.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds a consistency check to avoid OOPS, if tuner_callback priv argument is
NULL. Also, simplifies callback codes on cx88.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ISL6405 LNB supply is used on several Creatix / Medion cards. But only
the MD8800 needs its second section. So don't start it unless it is needed.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes reported problems when trying to add a 9th device into a
system.
Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner refactoring broke support of tuners with LNA configurations 1 and 2
for both, analog TV and DVB-T.
Additionally, this patch initializes the saa713x gpios defined by the gpiomask
at driver init to avoid undefined stated at dvb.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are some restrictions:
- The 2nd DVB-S section will only work if the 1st is configured for DVB-S too.
so "options saa7134-dvb use_frontend=0,1" won't work.
- Currently it is not possible to set the higher LNB supply voltages, so
14V instead of 13V in the 2nd section.
- It is not possibe to turn off the 2nd LNB supply independently.
This comes from the problem that the 2nd section can't access the i2c interface
of the LNB supply chip.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
