Properly report aborted commands.
Also don't access cmdinfo after kicking task management,
it may not be valid any more once it returns.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate one tag for task management functions and
use it properly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device with an isochronous endpoint is behind a hub plugged into
the Intel Panther Point xHCI host controller, and the driver submits
multiple frames per URB, the xHCI driver will set the Block Event
Interrupt (BEI) flag on all but the last TD for the URB. This causes
the host controller to place an event on the event ring, but not send an
interrupt. When the last TD for the URB completes, BEI is cleared, and
we get an interrupt for the whole URB.
However, under a Panther Point xHCI host controller, if the parent hub
is unplugged when one or more events from transfers with BEI set are on
the event ring, a port status change event is placed on the event ring,
but no interrupt is generated. This means URBs stop completing, and the
USB device disconnect is not noticed. Something like a USB headset will
cause mplayer to hang when the device is disconnected.
If another transfer is sent (such as running `sudo lsusb -v`), the next
transfer event seems to "unstick" the event ring, the xHCI driver gets
an interrupt, and the disconnect is reported to the USB core.
The fix is not to use the BEI flag under the Panther Point xHCI host.
This will impact power consumption and system responsiveness, because
the xHCI driver will receive an interrupt for every frame in all
isochronous URBs instead of once per URB.
Intel chipset developers confirm that this bug will be hit if the BEI
flag is used on any endpoint, not just ones that are behind a hub.
This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
PHY_CLK_VALID bit doesn't work properly with UTMI PHY.
e.g. This bit is always zero on P5040, etc.
There is no need to check this bit for UTMI PHY, just keep
checking for ULPI PHY to prevent system hanging.
This patch should be squashed into previous commit 3735ba8db8
"powerpc/usb: fix bug of CPU hang when missing USB PHY clock"
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIAO/DIYGADGET USB Multi-Protocol Adapter (TUMPA) is an FTDI FT2232H
based device which provides an easily accessible JTAG, SPI, I2C, serial
breakout.
http://www.diygadget.com/tiao-usb-multi-protocol-adapter-jtag-spi-i2c-serial.htmlhttp://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User%27s_Manual
FTDI FT2232H provides two serial channels (A and B), but on the TUMPA
channel A is dedicated to JTAG/SPI while channel B can be used for
UART/RS-232: use the ftdi_jtag_quirk to expose only channel B as
a usb-serial interface to userspace.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ca9c9d0c92.
Rafael wants more time to work on the user api to handle port power
issues, so let's just revert the sysfs changes for now.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's out-dated for the tty-layer stuff, and would require a bunch of
work. That's not really a big deal, the big issue is that there is no
company contact for the hardware, so questions we have about it (like
why isn't this just handled by the cdc-acm driver instead?) go
unanswered.
So drop the driver. If someone comes along to help answer the
questions, we can easily revert this and fix up the code.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rob Duncan <rob.duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 71c731a: usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware
when extracting DMI strings (vendor or product_name) to mark them as quirk
we may get NULL pointer in case of non-x86 systems which won't define
CONFIG_DMI. Hence susbsequent strstr() calls crash while driver probing.
So, returning 'false' here in case we get a NULL vendor or product_name.
This is tested with ARM (exynos) system.
This patch should be backported to stable kernels as old as 3.6, that
contain the commit 71c731a296 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Sebastian Gottschall (DD-WRT) <s.gottschall@dd-wrt.com>
Cc: stable@vger.kernel.org
The Intel XHCI specification says that after clearing the run/stop bit
the controller may take up to 16ms to halt. We've seen a device take
14ms, which with the current timeout of 10ms causes the kernel to
abort the suspend. Increasing the timeout to the recommended value
fixes the problem.
This patch should be backported to kernels as old as 2.6.37, that
contain the commit 5535b1d5f8 "USB: xHCI:
PCI power management implementation".
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
We need to call scsi_get_host_dev(sh) but we never use the return
nor do we have any reason to check it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for USB controller version 2.4
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The three Pantech devices UML190 (106c:3716), UML290 (106c:3718) and
P4200 (106c:3721) all use the same subclasses to identify vendor
specific functions. Replace the existing device specific entries
with generic vendor matching, adding support for the P4200.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1606) converts two warning messages in the ehci-hcd
driver to debug messages, and adds a little extra information to each.
The log messages occur when an EHCI controller takes too long (more
than 20 ms) to turn its async or periodic schedule on or off. If this
happens at all, it's liable to happen quite often and there's no point
spamming the system log with these warnings. Furthermore, there's
nothing much we can do about it when the problem happens.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Thomas Voegtle <tv@lio96.de>
Cc: stable <stable@vger.kernel.org> # [3.6]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1605) removes a useless test from the EHCI debugfs
code. There's no point checking whether p.qh is non-NULL; we already
know it is and in any case it gets dereferenced aerlier in the
function.
The useless test was identified by smatch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I fixed up all of the #ifdef stuff, so remove the comment saying it
still needs to be removed.
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rob Duncan <rob.duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQU4miAAoJEMhvYp4jgsXi1vMH/A4JJXe24cyo31rHJspZDSFg
nnCbnGKfDEOIHwLA8C3OeJuhswMlP/vWlGC512QXL8903XpZ2VJe63f2CLo1mN7Z
hg3JPWrp2VXZ/bqdMnUcw2CtlylrhyG9MUPapkcp+5Agjz2lwaJtRNL6LRRQX4Ei
cWjsJtaFpRj1QraFna0hpTQNO640je6s1rAIJl6eNOuX08l12ZAGDUA+IUUsa1cA
0OGeOAjH6gmkpMI89j1VPPKVRLHIdP4QcxmAZCHJ2LtvylyrlmYskctpAYibobvt
JPLnZgzMFAegnWtJhOYodhBJlfyypEeh2fsZVyDPowqRz9vaAWRjs6u/I4GYaME=
=HR3H
-----END PGP SIGNATURE-----
Merge tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux into next/multiplatform
Enable initial ARM multi-platform support for highbank, mvebu,
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
By Rob Herring (18) and Arnd Bergmann (1)
via Rob Herring
* tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux:
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
ARM: orion: move custom gpio functions to orion-gpio.h
ARM: shmobile: move custom gpio functions to sh-gpio.h
ARM: pxa: use gpio_to_irq for sharppm_sl
net: pxaficp_ir: add irq resources
usb: pxa27x_udc: remove IRQ_USB define
staging: ste_rmi4: remove gpio.h include
Conflicts due to addition of bcm2835 and removal of pnx4008 in:
arch/arm/Kconfig
arch/arm/Makefile
Conflicts due to new dtb targets, moved to arch/arm/boot/dts/Makefile in:
arch/arm/mach-imx/Makefile.boot
arch/arm/mach-mxs/Makefile.boot
arch/arm/mach-tegra/Makefile.boot
Signed-off-by: Olof Johansson <olof@lixom.net>
acpi_get_physical_device_location()'s 2nd argument has been changed
in ACPI implementaion, so need a follow-on change in
usb_acpi_check_pld().
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=TZVo
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
This branch contains mostly scripted changes to make omap
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
* tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_core_44xx.h local
ARM: OMAP2+: Make ctrl_module_core_44xx.h local
ARM: OMAP2+: Make board-rx51.h local
...
This branch mainly removes dead code following the removal of all board
files. The removals depend on various changes in other branches, so they
are all merged together and form the basis of this branch, as enumerated
below.
Finally, there are no remaining users of pinconf-tegra.h outside the
pinctrl subsystem, so that header is incorporated into an existing file
there. This reduces the number of headers in mach-tegra/include, and so
helps move towards single zImage.
This branch is based on tegra-for-3.7-cleanup, followed by a merge of
tegra-for-3.7-board-removal, followed by a merge of
tegra-for-3.7-common-clk, followed by a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git xceiv-for-v3.7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ltZ+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup2
ARM: tegra: second round of cleanups
This branch mainly removes dead code following the removal of all board
files. The removals depend on various changes in other branches, so they
are all merged together and form the basis of this branch, as enumerated
below.
Finally, there are no remaining users of pinconf-tegra.h outside the
pinctrl subsystem, so that header is incorporated into an existing file
there. This reduces the number of headers in mach-tegra/include, and so
helps move towards single zImage.
This branch is based on tegra-for-3.7-cleanup, followed by a merge of
tegra-for-3.7-board-removal, followed by a merge of
tegra-for-3.7-common-clk, followed by a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb.git xceiv-for-v3.7
By Stephen Warren (16) and others
via Stephen Warren
* tag 'tegra-for-3.7-cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (29 commits)
pinctrl: tegra: move pinconf-tegra.h content into drivers/pinctrl
ARM: tegra: delete unused headers
ARM: tegra: remove useless includes of <mach/*.h>
ARM: tegra: remove dead code
ARM: dt: tegra: harmony: configure power off
ARM: dt: tegra: harmony: add regulators
ARM: tegra: remove board (but not DT) support for Harmony
ARM: tegra: remove board (but not DT) support for Paz00
ARM: tegra: remove board (but not DT) support for TrimSlice
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
...
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/qVp
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into next/cleanup2
usb: xceiv: patches for v3.7 merge window
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
* tag 'xceiv-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: otg: mxs-phy: Fix mx23 operation
usb: dwc3: add basic PHY support
usb: dwc3: exynos: add nop transceiver support
usb: dwc3: omap: add nop transceiver support
usb: dwc3: pci: add nop transceiver support
usb: otg: move the dereference below the NULL test
arm: omap: phy: remove unused functions from omap-phy-internal.c
usb: twl4030: Add device tree support for twl4030 usb
usb: twl6030: Add dt support for twl6030 usb
usb: otg: make twl6030_usb as a comparator driver to omap_usb2
usb: phy: add a new driver for omap usb2 phy
usb: phy: fix build break
usb: move phy driver from mach-tegra to drivers/usb
usb: otg: Move phy interface to separate file.
usb: phy: isp1301: Remove unused static array and define
usb: phy: mv_u3d: Add usb phy driver for mv_u3d
usb: otg: Remove the unneeded NULL check
usb: xceiv: nop: let it work as USB2 and USB3 phy
usb: xceiv: create nop-usb-xceiv.h and avoid pollution on otg.h
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
We are moving omap2+ to use the device tree based pinctrl-single.c
and will be removing the old mux framework. This will remove the
omap1 specific parts from plat-omap.
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-pcmcia@lists.infradead.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Tony Lindgren <tony@atomide.com>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the samsung include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the orion include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
As reported by Fengguang:
FYI, coccinelle warns about
drivers/usb/serial/usb-serial.c:1415:3-51: code aligned with following code on line 1416
vim +1415 drivers/usb/serial/usb-serial.c
1412 /* we only set the reset_resume field if the serial_driver has one */
1413 for (sd = serial_drivers; *sd; ++sd) {
1414 if ((*sd)->reset_resume)
> 1415 udriver->reset_resume = usb_serial_reset_resume;
> 1416 break;
1417 }
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: stable <stable@vger.kernel.org> [3.5]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds new functions to upload firmware to the controller. The
drivers currently using ezusb are adapted to use these new functions.
This also fixes a bug occuring during firmware loading in the
whiteheat-driver:
The driver iterates over an ihex-formatted firmware using ++ on a "const
struct ihex_binrec*" which leads to faulty results, because ihex data is
read as length. The function "ihex_next_binrec(record)" has so be used
to work correctly
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Patch adds support for the newer Cypress FX2LP. It also adapts
three drivers currently using ezusb to the interface change. (whiteheat
and keyspan[_pda])
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like for the in-tree early console debug port driver, the
hypervisor - when using a debug port based console - also needs to be
told about controller resets, so it can suppress using and then
re-initialize the debug port accordingly.
Other than the in-tree driver, the hypervisor driver actually cares
about doing this only for the device where the debug is port actually
in use, i.e. it needs to be told the coordinates of the device being
reset (quite obviously, leveraging the addition done for that would
likely benefit the in-tree driver too).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves to using pr_info() where needed instead of a "raw" printk()
call, making the whole driver more unified.
It also cleans up my email address in the MODULE_AUTHOR field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver should not be sending any printk() messages when it is
loaded, as no other USB serial driver does. This fixes that, and also
removes the useless version number from the driver.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was calling printk() directly at startup, which is just
noise. Switch over to using pr_info() where needed, and get rid of the
totally useless version number that had never ever been incremented.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should be calling dev_err() instead of printk(KERN_INFO...) so this
change fixes that up properly.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These somehow got missed previously (as they weren't calling dbg(), but
rather printk() directly), so move over to using dev_dbg() as we never
want to see startup messages unless debugging is enabled.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't be telling the syslog that the driver was loaded, the majority of
the usb-serial drivers do not, so this one shouldn't either.
Also remove the pointless driver version information.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err() like the rest of that function does, and the rest of the
driver does, to properly show what device and driver caused the problem.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No one needs to know that the driver is loaded (almost all other USB
serial drivers are now quiet), so just load quietly.
Also remove unused, and unneeded version information from the driver,
that was pointless.
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code shouldn't be calling printk(), no one needs to know this debug
message, the return code is good enough.
Cc: "René Bürgel" <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try
to use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I forgot to remove an unused variable.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Support Department <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: "Bjørn Mork" <bjorn@mork.no>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Wang YanQing <Udknight@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Mark Ferrell <mferrell@uplogix.com>
CC: Donald Lee <donald@asix.com.tw>
CC: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Lonnie Mendez <dignome@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should use dev_dbg() for usb_serial_debug_data() like all of the rest
of the usb-serial drivers use, so remove the debug parameter as it's not
needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Neil Zhang <zhangwm@marvell.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a driver for the Vizzini USB to serial device.
It looks to be copied from cdc-acm, and probably can be cleaned up a lot
more. Also, there's some odd "try to grab another interface" that is
probably wrong. And, if this really is a cdc-acm device, it probably
should just be a quirk of the cdc-acm device, but I can't figure that
out, and people have been using this driver for a long time now. So
merge it to let people use their hardware and clean it up over time.
Driver written by Rob Duncan but cleaned up and forward ported to the
latest kernel tree by me.
Cc: Rob Duncan <rob.duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every fabric driver has to supply a se_tfo->set_fabric_sense_len()
method, just so iSCSI can return an offset of 2. However, every fabric
driver is already allocating a sense buffer and passing it into the
target core, either via transport_init_se_cmd() or target_submit_cmd().
So instead of having iSCSI pass the start of its sense buffer into the
core and then later tell the core to skip the first 2 bytes, it seems
easier for iSCSI just to do the offset of 2 when it passes the sense
buffer into the core. Then we can drop the se_tfo->set_fabric_sense_len()
everywhere, and just add a couple of lines of code to iSCSI to set the
sense data length to the beginning of the buffer right before it sends
it over the network.
(nab: Remove .set_fabric_sense_len usage from tcm_qla2xxx_npiv_ops +
change transport_get_sense_buffer to follow v3.6-rc6 code w/o
->set_fabric_sense_len usage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are no callers of se_tfo->get_fabric_sense_len(), so we should
stop having every fabric driver implement it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
retval is 0, and carefully assigned - and tested as non zero.
This is not useful. While we are at it remove some other bogus initialisation
in the function
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This part of the tty tree (unfortunately with all the preceding patches
as well) is a dependency for some of the OMAP cleanups, so we've pulled
it in as a dependency based on agreement with Greg.
Signed-off-by: Olof Johansson <olof@lixom.net>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I accidentally caused some compiler warnings, that were correct in
pointing out problems, so fix them up now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the keyspan
driver and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Mark Ferrell <mferrell@uplogix.com>
CC: Donald Lee <donald@asix.com.tw>
CC: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: "Bjørn Mork" <bjorn@mork.no>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: "Bjørn Mork" <bjorn@mork.no>
CC: Dan Williams <dcbw@redhat.com>
CC: Thomas Tuttle <ttuttle@chromium.org>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
