When File Storage gadget receives SET CONFIGURATION request it tries
to cancel all pending transfers. If some request is in progress,
gadget waits for its completion. This commit allows gadget to dequeue
invalid requests in progress left after reset.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Reviewed-by: Kyoungil Kim<ki0351.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following should be done for requests after endpoint stall
condition is cleared:
1) 'in progress' request (if any) should be completed since
Tx FIFO was flushed;
2) next request from queue (if any) should be started.
This commit does that.
Additionally set/clear stall condition code is fixed.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Reviewed-by: Kyoungil Kim<ki0351.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UDC driver does not need to generate reply to host if request is
delivered to gadget. This is gadget's responsibility. This commit
fixes that.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Reviewed-by: Kyoungil Kim<ki0351.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit does the following:
1) clears all pending interrupts before unmasking;
2) clears interrupts as soon as possible to avoid missing
next coming that may occur during handling;
3) removes ineffective interrupt cleaning code.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Reviewed-by: Kyoungil Kim<ki0351.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extend the FSL UDC driver to support MPC5121E DR USB Controller
operation in device mode. Add MPC5121E specific init/uninit
at probe and remove and isolate system interface register accesses
when running on MPC5121E SoC, as these registers are not available
on this platform. This patch relies on previous patch for supporting
big endian registers and descriptors access in the FSL UDC driver.
Additionally support endpoint FIFO status operation by providing
appropriate callback in endpoint ops structure.
Also flush cache for the req buffer used for GetStatus reply.
Without this, the correct reply to an endpoint GetStatus
is written to 'req', but doesn't make it out to the USB bus
since the buffer hasn't been flushed. This would cause the
USBCV Halt Endpoint test to fail (according to changelog in
Freescale LTIB driver code).
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some SoCs, the USB controller registers and descriptors can be big
or little endian, depending on the version of the chip. In order to be
able to run the same kernel binary on different versions of an SoC, the
BE/LE decision must be made at run time. Provide appropriate register
and descriptor accessors which are configurable at run time using the
configuration flags from fsl_usb2_platform_data data structure.
This is in preparation for adding support for MPC5121E DR USB2 Controller
to the FSL UDC driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit fixes an embarrassing bug in the "storage_common:
use kstrto*()" patch which caused fsg_store_ro() to return
zero instead of the length of the consumed buffer.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the_controller is allocated in dummy_hcd_probe() and is NULL if the
allocation failed. The probe function of the udc driver is dereferencing
this pointer and fault.
Alan Stern suggested to abort the dummy_hcd driver probing so the module
is not loaded. The is abort-on-error has been also added to the udc
driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_printer reqiured "set interface" request from host. Not all hosts send
this request. This patch enable the interface when it get "set
configuration" request from host.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stripping the direction bit off will produce an
invalid descriptor.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current code doesn't set it, so linux complains about
it when connected, and ignores the device:
[104611.068082] usb 1-5: new high speed USB device using ehci_hcd and address 127
[104611.088368] usb 1-5: Invalid ep0 maxpacket: 0
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current code returns 0 even if it can't handle the request.
This leads to timeouts when an unhandled request is sent:
Bus 001 Device 003: ID 0525:c0de Netchip Technology, Inc.
Device Descriptor:
[..]
can't get device qualifier: Connection timed out
[..]
change the code to return EOPNOTSUPP in such cases.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 806e8f8fcc.
To quote Alan Stern:
The necessity for this patch has been under discussion.
It turns out the UDC that Mian has been working on and Felipe's
UDC have contradictory requirements. Mian's UDC driver wants a
bulk-OUT transfer length to be shorter than the maxpacket size
if a short packet is expected, whereas Felipe's UDC hardware
always needs bulk-OUT transfer lengths to be evenly divisible by
the maxpacket size.
Mian has agreed to go back over the driver to resolve this
conflict. This means we probably will not want this patch after
all. (In fact, we may ultimately decide to change the gadget
framework to require that bulk-OUT transfer lengths _always_ be
divisible by the maxpacket size -- only the g_file_storage and
g_mass_storage gadgets would need to be changed.)
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit replaces the usage of strict_strtoul() (which
became deprecated after commit 33ee3b2e) with kstrtouint().
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we don't need Write access then attempt to open backing file in Read Only
mode instead of bailing out too soon.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ep0 request tag was not recorded thus resulting in phase
problems while sending status/response in handle_execption() handler.
This was resulting in MSC compliance test failures with USBCV tool.
With this patch, the Bulk-Only Mass storage RESET request is
handled correctly and the MSC compliance tests pass.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1455) removes the extra padding sent by g_file_storage
and g_mass_storage when the gadget wants to send less data than
requested by the host and isn't allowed to halt the bulk-IN endpoint.
Although the Bulk-Only Transport specification requires the padding to
be present, it isn't truly needed since the transfer will be terminated
by a short packet anyway. Furthermore, many existing devices don't
bother to send any padding.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-By: Michal Nazarewicz <mina86@mina86.com>
CC: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mass-storage and file-storage gadgets align the length to maximum-packet-size
when preparing the request to receive CBW. This is unnecessary and prevents the
controller driver from knowing that a short-packet is expected.
It is incorrect to set short_not_ok when preparing the request to receive CBW.
CBW will be a short-packet so short_not_ok must not be set.
This makes bh->bulk_out_intended_length unnecessary so it is also removed.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver did not take the zero flag in the USB request. If the
request length is the same as the endpoint's maxpacket, an additional
ZLP with no data has to be transmitted.
The method used here is inspired to what is done in fsl_udc_core.c
(and pxa27x_udc.c and at91_udc.c) where this is supported.
There already was a discussion about this topic with people from
Keymile, and I propose here a better implementation:
http://thread.gmane.org/gmane.linux.usb.general/38951
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was an unlock missing on the error path.
Also I did a small cleanup by changing ep->dev->lock for just dev->lock.
They're the same lock, but dev->lock is shorter and that's how it is
used for the spin_unlock_irqrestore() call.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During processing of bunch of eem frames if "echo" command is found
skb is cloned and the cloned version should be used to send reply.
Unfortunately, the data of the original skb were actually used and
the cloned skb is never freed.
Using the cloned skb and freeing the skb in the completion callback
for usb request.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because the disconnect function in the composite driver will call spin_lock,
this driver has to call spin_unlock before calling driver->disconnet().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ep_read() acquires data->lock mutex in get_ready_ep() and releases it on
all paths except for one: when usb_endpoint_xfer_isoc() failed. The
patch adds mutex_unlock(&data->lock) at that path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop handling gpio-vbus internally. All boards that depended on this
functionality have been converted to use gpio-vbus tranceiver. All
new boards can use it right from the start. Drop unused code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Update the USB core to deal with USB 3.0 hubs. These hubs have a slightly
different hub descriptor than USB 2.0 hubs, with a fixed (rather than
variable length) size. Change the USB core's hub descriptor to have a
union for the last fields that differ. Change the host controller drivers
that access those last fields (DeviceRemovable and PortPowerCtrlMask) to
use the union.
Translate the new version of the hub port status field into the old
version that khubd understands. (Note: we need to fix it to translate the
roothub's port status once we stop converting it to USB 2.0 hub status
internally.)
Add new code to handle link state change status. Send out new control
messages that are needed for USB 3.0 hubs, like Set Hub Depth.
This patch is a modified version of the original patch submitted by John
Youn. It's updated to reflect the removal of the "bitmap" #define, and
change the hub descriptor accesses of a couple new host controller
drivers.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Using a #define to redefine a common variable name is a bad thing,
especially when the #define is in a header. include/linux/usb/hcd.h
redefined bitmap to DeviceRemovable to avoid typing a long field in the
hub descriptor. This has unintended side effects for files like
drivers/usb/core/devio.c that include that file, since another header
included after hcd.h has different variables named bitmap.
Remove the bitmap #define and replace instances of it in the host
controller code. Cleanup the spaces around function calls and square
brackets while we're at it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
file.
This patch adds support for using a GPIO to control the pullup state to the udc
driver, so the boards can use a common implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is used across all MSM SoCs. Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
is_iso variable is not used anywhere, remove it
Signed-off-by: Huzaifa Sidhpurwala <huzaifas@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver was taking max() of a size_t and u32 which causes complaint
about comparison of different types.
Stumbled on this accidently in my config, never used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is similar to what we already do in cdc-phonet.c in the same
situation. pskb_pull() refuses to work with HIGHMEM, even if it is
known that the socket buffer is entirely in "low" memory.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of users of of_platform_driver in drivers/usb. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When USB CV MSC tests are run on f_mass_storage gadget
Bulk Only Mass Storage Reset fails since req->length
is set to USB_BUFSIZ=1024 in composite_setup().
Initialize req->length to zero to fix this.
Signed-off-by: Maulik Mankad <maulik@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is similar to what we already do in cdc-phonet.c in the same
situation.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement the test modes mentioned in 7.1.20 section of USB 2.0
specification. High-speed capable devices must support these test
modes to facilitate compliance testing.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for remote wakeup. The following things
are handled:
- Process SET_FEATURE/CLEAR_FEATURE control requests sent by host
for enabling/disabling remote wakeup feature.
- Report remote wakeup enable status in response to GET_STATUS
control request.
- Implement wakeup method defined in usb_gadget_ops for initiating
remote wakeup.
- Notify gadget driver about suspend and resume.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Chipidea USB controller provides a means (Add dTD TripWire semaphore)
for safely adding a new dTD to an active endpoint's linked list. Make
use of this feature to improve performance. Dynamically allocate and
free dTD for supporting zero length packet termination. Honor
no_interrupt flag set by gadget drivers.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
