The only difference was the inline assembly, so move that into
asm/msr.h and merge with the i386 version.
This adds some missing sysfs support code to x86-64.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Being the foundation for reliable stack unwinding, this fixes CFI unwind
annotations in many low-level x86_64 routines, plus a config option
(available to all architectures, and also present in the previously sent
patch adding such annotations to i386 code) to enable them separatly
rather than only along with adding full debug information.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently just defined to their non range parts.
Pointed out by John Linville
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They should be identical in the kernel now, but this
makes it consistent with other code.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Needed for some newer Opteron systems with E stepping and memory
relocation enabled. The node addresses are different in lower
bits now so the nodemap hash function needs to be enlarged.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The generic TLB flush functions kept upto 506 pages per
CPU to avoid too frequent IPIs.
This value was done for the L1 cache of older x86 CPUs,
but with modern CPUs it does not make much sense anymore.
TLB flushing is slow enough that using the L2 cache is fine.
This patch increases the flush array on x86-64 to cache
5350 pages. That is roughly 20MB with 4K pages. It speeds
up large munmaps in multithreaded processes on SMP considerably.
The cost is roughly 42k of memory per CPU, which is reasonable.
I only increased it on x86-64 for now, but it would probably
make sense to increase it everywhere. Embedded architectures
with SMP may keep it smaller to save some memory per CPU.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
asm-x86-64/timex.h does not reference CONFIG constants.
Do not need to include config.h.
Signed-off-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of using a global spinlock to protect the state
of the remote TLB flush use a lock and state for each sending CPU.
To tell the receiver where to look for the state use 8 different
call vectors. Each CPU uses a specific vector to trigger flushes on other
CPUs. Depending on the received vector the target CPUs look into
the right per cpu variable for the flush data.
When the system has more than 8 CPUs they are hashed to the 8 available
vectors. The limited global vector space forces us to this right now.
In future when interrupts are split into per CPU domains this could be
fixed, at the cost of needing more IPIs in flat mode.
Also some minor cleanup in the smp flush code and remove some outdated
debug code.
Requires patch to move cpu_possible_map setup earlier.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The FLATMEM people added it, but there doesn't seem a good reason
because end_pfn is identical.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_DMA_BUS_IS_PHYS has to be zero even when the GART IOMMU is disabled
and the swiotlb is used. Otherwise the block layer does unnecessary
double bouncing.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In particular on systems where the local APIC space and node space
is very different from the Linux CPU number space.
Previously the older NUMA setup code directly parsing the K8
northbridge registers had some issues on 8 socket or dual core
systems. This patch fixes them.
This is mainly done by fixing some confusion between Linux
CPU numbers and local APIC ids. We now pass the local APIC IDs
to later code, which avoids mismatches.
Also add some heuristics to detect cases where the Hypertransport
nodeids and the local APIC IDs don't match, but are shifted
by a constant offset.
This is still all quite hackish, hopefully BIOS writers fill
in correct SRATs instead.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do that later when the CPU boots. SRAT just stores the APIC<->Node
mapping node. This fixes problems on systems where the order
of SRAT entries does not match the MADT.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was just needed for the Numasaurus, which fortunately
doesn't support x86-64 CPUs.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No x86-64 chipset has this bug
Generated code doesn't change because it was always disabled.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
get_cpu_vendor() no longer has any users in other files.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (written by me and also containing many suggestions of Arjan van
de Ven) does a major cleanup of the spinlock code. It does the following
things:
- consolidates and enhances the spinlock/rwlock debugging code
- simplifies the asm/spinlock.h files
- encapsulates the raw spinlock type and moves generic spinlock
features (such as ->break_lock) into the generic code.
- cleans up the spinlock code hierarchy to get rid of the spaghetti.
Most notably there's now only a single variant of the debugging code,
located in lib/spinlock_debug.c. (previously we had one SMP debugging
variant per architecture, plus a separate generic one for UP builds)
Also, i've enhanced the rwlock debugging facility, it will now track
write-owners. There is new spinlock-owner/CPU-tracking on SMP builds too.
All locks have lockup detection now, which will work for both soft and hard
spin/rwlock lockups.
The arch-level include files now only contain the minimally necessary
subset of the spinlock code - all the rest that can be generalized now
lives in the generic headers:
include/asm-i386/spinlock_types.h | 16
include/asm-x86_64/spinlock_types.h | 16
I have also split up the various spinlock variants into separate files,
making it easier to see which does what. The new layout is:
SMP | UP
----------------------------|-----------------------------------
asm/spinlock_types_smp.h | linux/spinlock_types_up.h
linux/spinlock_types.h | linux/spinlock_types.h
asm/spinlock_smp.h | linux/spinlock_up.h
linux/spinlock_api_smp.h | linux/spinlock_api_up.h
linux/spinlock.h | linux/spinlock.h
/*
* here's the role of the various spinlock/rwlock related include files:
*
* on SMP builds:
*
* asm/spinlock_types.h: contains the raw_spinlock_t/raw_rwlock_t and the
* initializers
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* asm/spinlock.h: contains the __raw_spin_*()/etc. lowlevel
* implementations, mostly inline assembly code
*
* (also included on UP-debug builds:)
*
* linux/spinlock_api_smp.h:
* contains the prototypes for the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*
* on UP builds:
*
* linux/spinlock_type_up.h:
* contains the generic, simplified UP spinlock type.
* (which is an empty structure on non-debug builds)
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* linux/spinlock_up.h:
* contains the __raw_spin_*()/etc. version of UP
* builds. (which are NOPs on non-debug, non-preempt
* builds)
*
* (included on UP-non-debug builds:)
*
* linux/spinlock_api_up.h:
* builds the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*/
All SMP and UP architectures are converted by this patch.
arm, i386, ia64, ppc, ppc64, s390/s390x, x64 was build-tested via
crosscompilers. m32r, mips, sh, sparc, have not been tested yet, but should
be mostly fine.
From: Grant Grundler <grundler@parisc-linux.org>
Booted and lightly tested on a500-44 (64-bit, SMP kernel, dual CPU).
Builds 32-bit SMP kernel (not booted or tested). I did not try to build
non-SMP kernels. That should be trivial to fix up later if necessary.
I converted bit ops atomic_hash lock to raw_spinlock_t. Doing so avoids
some ugly nesting of linux/*.h and asm/*.h files. Those particular locks
are well tested and contained entirely inside arch specific code. I do NOT
expect any new issues to arise with them.
If someone does ever need to use debug/metrics with them, then they will
need to unravel this hairball between spinlocks, atomic ops, and bit ops
that exist only because parisc has exactly one atomic instruction: LDCW
(load and clear word).
From: "Luck, Tony" <tony.luck@intel.com>
ia64 fix
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjanv@infradead.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Mikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The function prototype for handle_IRQ_event() in a few architctures is not
needed because they use GENERIC_HARDIRQ.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch just gathers together all the struct flock definitions except
xtensa into asm-generic/fcntl.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch puts the most popular of each fcntl operation/flag into
asm-generic/fcntl.h and cleans up the arch files.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch puts the most popular of each open flag into asm-generic/fcntl.h
and cleans up the arch files.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This set of patches creates asm-generic/fcntl.h and consolidates as much as
possible from the asm-*/fcntl.h files into it.
This patch just gathers all the identical bits of the asm-*/fcntl.h files into
asm-generic/fcntl.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
unused and useless..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The size of auxiliary vector is fixed at 42 in linux/sched.h. But it isn't
very obvious when looking at linux/elf.h. This patch adds AT_VECTOR_SIZE
so that we can change it if necessary when a new vector is added.
Because of include file ordering problems, doing this necessitated the
extraction of the AT_* symbols into a standalone header file.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When I first wrote the compat layer patches, I was somewhat cavalier about
the definition of compat_uid_t and compat_gid_t (or maybe I just
misunderstood :-)). This patch makes the compat types much more consistent
with the types we are being compatible with and hopefully will fix a few
bugs along the way.
compat type type in compat arch
__compat_[ug]id_t __kernel_[ug]id_t
__compat_[ug]id32_t __kernel_[ug]id32_t
compat_[ug]id_t [ug]id_t
The difference is that compat_uid_t is always 32 bits (for the archs we
care about) but __compat_uid_t may be 16 bits on some.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ATM pthread_cond_signal is unnecessarily slow, because it wakes one waiter
(which at least on UP usually means an immediate context switch to one of
the waiter threads). This waiter wakes up and after a few instructions it
attempts to acquire the cv internal lock, but that lock is still held by
the thread calling pthread_cond_signal. So it goes to sleep and eventually
the signalling thread is scheduled in, unlocks the internal lock and wakes
the waiter again.
Now, before 2003-09-21 NPTL was using FUTEX_REQUEUE in pthread_cond_signal
to avoid this performance issue, but it was removed when locks were
redesigned to the 3 state scheme (unlocked, locked uncontended, locked
contended).
Following scenario shows why simply using FUTEX_REQUEUE in
pthread_cond_signal together with using lll_mutex_unlock_force in place of
lll_mutex_unlock is not enough and probably why it has been disabled at
that time:
The number is value in cv->__data.__lock.
thr1 thr2 thr3
0 pthread_cond_wait
1 lll_mutex_lock (cv->__data.__lock)
0 lll_mutex_unlock (cv->__data.__lock)
0 lll_futex_wait (&cv->__data.__futex, futexval)
0 pthread_cond_signal
1 lll_mutex_lock (cv->__data.__lock)
1 pthread_cond_signal
2 lll_mutex_lock (cv->__data.__lock)
2 lll_futex_wait (&cv->__data.__lock, 2)
2 lll_futex_requeue (&cv->__data.__futex, 0, 1, &cv->__data.__lock)
# FUTEX_REQUEUE, not FUTEX_CMP_REQUEUE
2 lll_mutex_unlock_force (cv->__data.__lock)
0 cv->__data.__lock = 0
0 lll_futex_wake (&cv->__data.__lock, 1)
1 lll_mutex_lock (cv->__data.__lock)
0 lll_mutex_unlock (cv->__data.__lock)
# Here, lll_mutex_unlock doesn't know there are threads waiting
# on the internal cv's lock
Now, I believe it is possible to use FUTEX_REQUEUE in pthread_cond_signal,
but it will cost us not one, but 2 extra syscalls and, what's worse, one of
these extra syscalls will be done for every single waiting loop in
pthread_cond_*wait.
We would need to use lll_mutex_unlock_force in pthread_cond_signal after
requeue and lll_mutex_cond_lock in pthread_cond_*wait after lll_futex_wait.
Another alternative is to do the unlocking pthread_cond_signal needs to do
(the lock can't be unlocked before lll_futex_wake, as that is racy) in the
kernel.
I have implemented both variants, futex-requeue-glibc.patch is the first
one and futex-wake_op{,-glibc}.patch is the unlocking inside of the kernel.
The kernel interface allows userland to specify how exactly an unlocking
operation should look like (some atomic arithmetic operation with optional
constant argument and comparison of the previous futex value with another
constant).
It has been implemented just for ppc*, x86_64 and i?86, for other
architectures I'm including just a stub header which can be used as a
starting point by maintainers to write support for their arches and ATM
will just return -ENOSYS for FUTEX_WAKE_OP. The requeue patch has been
(lightly) tested just on x86_64, the wake_op patch on ppc64 kernel running
32-bit and 64-bit NPTL and x86_64 kernel running 32-bit and 64-bit NPTL.
With the following benchmark on UP x86-64 I get:
for i in nptl-orig nptl-requeue nptl-wake_op; do echo time elf/ld.so --library-path .:$i /tmp/bench; \
for j in 1 2; do echo ( time elf/ld.so --library-path .:$i /tmp/bench ) 2>&1; done; done
time elf/ld.so --library-path .:nptl-orig /tmp/bench
real 0m0.655s user 0m0.253s sys 0m0.403s
real 0m0.657s user 0m0.269s sys 0m0.388s
time elf/ld.so --library-path .:nptl-requeue /tmp/bench
real 0m0.496s user 0m0.225s sys 0m0.271s
real 0m0.531s user 0m0.242s sys 0m0.288s
time elf/ld.so --library-path .:nptl-wake_op /tmp/bench
real 0m0.380s user 0m0.176s sys 0m0.204s
real 0m0.382s user 0m0.175s sys 0m0.207s
The benchmark is at:
http://sourceware.org/ml/libc-alpha/2005-03/txt00001.txt
Older futex-requeue-glibc.patch version is at:
http://sourceware.org/ml/libc-alpha/2005-03/txt00002.txt
Older futex-wake_op-glibc.patch version is at:
http://sourceware.org/ml/libc-alpha/2005-03/txt00003.txt
Will post a new version (just x86-64 fixes so that the patch
applies against pthread_cond_signal.S) to libc-hacker ml soon.
Attached is the kernel FUTEX_WAKE_OP patch as well as a simple-minded
testcase that will not test the atomicity of the operation, but at least
check if the threads that should have been woken up are woken up and
whether the arithmetic operation in the kernel gave the expected results.
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Jamie Lokier <jamie@shareable.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a multi-part message in MIME format. If the cpu lacks 3DNOW
feature, we can use a normal prefetcht0 instruction instead of NOP5.
"prefetchw (%rxx)" and "prefetcht0 (%rxx)" have the same length, ranging
from 3 to 5 bytes depending on the register. So this patch even helps
AMD64, shortening the length of the code.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 arch cleanup. Introduce the serialize macro to serialize processor
state. Why the microcode update needs it I am not quite sure, since wrmsr()
is already a serializing instruction, but it is a microcode update, so I will
keep the semantic the same, since this could be a timing workaround. As far
as I can tell, this has always been there since the original microcode update
source.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Any architecture that has hardware updated A/D bits that require
synchronization against other processors during PTE operations can benefit
from doing non-atomic PTE updates during address space destruction.
Originally done on i386, now ported to x86_64.
Doing a read/write pair instead of an xchg() operation saves the implicit
lock, which turns out to be a big win on 32-bit (esp w PAE).
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is used only in slab.c and each architecture gets to define whcih
underlying type is to be used.
Seems a bit silly - move it to slab.c and use the same type for all
architectures: unsigned int.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I don't think we need to call hugetlb_clean_stale_pgtable() anymore
in 2.6.13 because of the rework with free_pgtables(). It now collect
all the pte page at the time of munmap. It used to only collect page
table pages when entire one pgd can be freed and left with staled pte
pages. Not anymore with 2.6.13. This function will never be called
and We should turn it into a BUG_ON.
I also spotted two problems here, not Adam's fault :-)
(1) in huge_pte_alloc(), it looks like a bug to me that pud is not
checked before calling pmd_alloc()
(2) in hugetlb_clean_stale_pgtable(), it also missed a call to
pmd_free_tlb. I think a tlb flush is required to flush the mapping
for the page table itself when we clear out the pmd pointing to a
pte page. However, since hugetlb_clean_stale_pgtable() is never
called, so it won't trigger the bug.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a macro pte_huge(pte) for i386/x86_64 which is needed by a
patch later in the series. Instead of repeating (_PAGE_PRESENT |
_PAGE_PSE), I've added __LARGE_PTE to i386 to match x86_64.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: <linux-mm@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
_PAGE_FILE does not indicate whether a file is in page / swap cache, it is
set just for non-linear PTE's. Correct the comment for i386, x86_64, UML.
Also clearify _PAGE_NONE.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Someone mentioned that almost all the architectures used basically the same
implementation of get_order. This patch consolidates them into
asm-generic/page.h and includes that in the appropriate places. The
exceptions are ia64 and ppc which have their own (presumably optimised)
versions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some nodes can have large holes on x86-64.
This fixes problems with the VM allowing too many dirty pages because it
overestimates the number of available RAM in a node. In extreme cases you
can end up with all RAM filled with dirty pages which can lead to deadlocks
and other nasty behaviour.
This patch just tells the VM about the known holes from e820. Reserved
(like the kernel text or mem_map) is still not taken into account, but that
should be only a few percent error now.
Small detail is that the flat setup uses the NUMA free_area_init_node() now
too because it offers more flexibility.
(akpm: lotsa thanks to Martin for working this problem out)
Cc: Martin Bligh <mbligh@mbligh.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete the ability to build an ACPI kernel that does
not include PCI support. When such a machine is created
and it requires a tuned kernel, send a patch.
http://bugzilla.kernel.org/show_bug.cgi?id=1364
Signed-off-by: Len Brown <len.brown@intel.com>
Chuck Ebbert noticed that the desc_empty macro is incorrect. Fix it.
Thankfully, this is not used as a security check, but it can falsely
overwrite TLS segments with carefully chosen base / limits. I do not
believe this is an issue in practice, but it is a kernel bug.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@osdl.org>
[ x86-64 had the same problem, and the same fix. Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commits
71db63acff
[PATCH] increase PCIBIOS_MIN_IO on x86
and
0b2bfb4e7f
ACPI: increase PCIBIOS_MIN_IO on x86
since Lukas Sandströ<lukass@etek.chalmers.se> reports that this breaks
his on-board nvidia audio.
We should re-visit this later. For now we revert the change
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a number of x86 laptops that have some non-PCI IO ports
in the 0x1000-0x1fff range, and it's quite hard to control the correct
order of resource allocation between PCI and other subsystems controlling
these ports. Especially with modular kernel.
So just increase PCIBIOS_MIN_IO to 0x4000 to prevent any new PCI
resource allocations in the problematic range (this limitation must
apply _only_ to the root bus resources - see Linus' change in
pci_bus_alloc_resource). As PCIBIOS_MIN_IO and PCIBIOS_MIN_CARDBUS_IO
are the same now on i386 and x86-64, we can remove the latter.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sync_tsc was using smp_call_function to ask the boot processor to report
it's tsc value. smp_call_function performs an IPI_send_allbutself which is
a broadcast ipi. There is a window during processor startup during which
the target cpu has started and before it has initialized it's interrupt
vectors so it can properly process an interrupt. Receveing an interrupt
during that window will triple fault the cpu and do other nasty things.
Why cli does not protect us from that is beyond me.
The simple fix is to match ia64 and provide a smp_call_function_single.
Which avoids the broadcast and is more efficient.
This certainly fixes the problem of getting stuck on boot which was
very easy to trigger on my SMP Hyperthreaded Xeon, and I think
it fixes it for the right reasons.
Minor changes by AK
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the standard hardware page table manipulation macros.
This is possible now that linux works with all 4 levels
of the page tables.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch eliminates the GCC4 warning on the x86_64 platform:
kernel/sched.c:1824: warning: control may reach end of non-void function
'sched_find_first_bit' being inlined.
The change follows the lead of others, i.e. it is guaranteed that at least
one of b[0], b[1], or b[2] will have a bit set and evaluate to true. That
being said, GCC4.0.0 notices that the code flow does not return anything if
b[0], b[1] and b[2] are not true. Since we know better, if it's not b[0] or
b[1], it has to be b[2].
Signed-off-by: Jesse Millan <jessem@cs.pdx.edu>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This avoids some potential stack overflows with very deep softirq callchains.
i386 does this too.
TOADD CFI annotation
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This avoids confusing the disassembler. Costs 2 bytes per BUG.
Thanks to Suresh Siddha and Jan Beulich for suggesting suitable instructions.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Harmless because the kernel didn't use it. Noticed by Travis Betak
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Were either outdated or misleading.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor cleanup.
Move things into their include files, remove obsolete includes, fix
indentation, remove obsolete special cases etc.
I also added the per cpu section to asm-generic/sections.h and fixed
init/main.c to use it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes it slightly more efficient.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is not safe to call set_cpus_allowed() in interrupt
context and disabling the apics is complicated code.
So unconditionally skip machine_shutdown in machine_emergency_reboot
on x86_64.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the kernel is working well and we want to restart cleanly
kernel_restart is the function to use. But in many instances
the kernel wants to reboot when thing are expected to be working
very badly such as from panic or a software watchdog handler.
This patch adds the function emergency_restart() so that
callers can be clear what semantics they expect when calling
restart. emergency_restart() is expected to be callable
from interrupt context and possibly reliable in even more
trying circumstances.
This is an initial generic implementation for all architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add inotify syscall entries to x86-64.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: John McCutchan <ttb@tentacle.dhs.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
http://bugme.osdl.org/show_bug.cgi?id=4016
Written-by: David Shaohua Li <shaohua.li@intel.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There has been some discuss about solving the SMP MTRR suspend/resume
breakage, but I didn't find a patch for it. This is an intent for it. The
basic idea is moving mtrr initializing into cpu_identify for all APs (so it
works for cpu hotplug). For BP, restore_processor_state is responsible for
restoring MTRR.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove legacy ISA serial ports for Accent, Boca, Fourport, Hub6 and MCA
from the architecture specific serial.h include.
The only ports which remain in asm-*/serial.h are the platform specific
entries. These should really be converted by platform maintainers to
use a platform device, such as can be found in
arch/arm/mach-footbridge/isa.c
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With CONFIG_PCI=n:
In file included from include/linux/pci.h:917,
from lib/iomap.c:6:
include/asm/pci.h:104: warning: `enum pci_dma_burst_strategy' declared inside parameter list
include/asm/pci.h:104: warning: its scope is only this definition or declaration, which is probably not what you want.
include/asm/pci.h: In function `pci_dma_burst_advice':
include/asm/pci.h:106: dereferencing pointer to incomplete type
include/asm/pci.h:106: `PCI_DMA_BURST_INFINITY' undeclared (first use in this function)
include/asm/pci.h:106: (Each undeclared identifier is reported only once
include/asm/pci.h:106: for each function it appears in.)
make[1]: *** [lib/iomap.o] Error 1
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After seeing, at best, "guesses" as to the following kind
of information in several drivers, I decided that we really
need a way for platforms to specifically give advice in this
area for what works best with their PCI controller implementation.
Basically, this new interface gives DMA bursting advice on
PCI. There are three forms of the advice:
1) Burst as much as possible, it is not necessary to end bursts
on some particular boundary for best performance.
2) Burst on some byte count multiple. A DMA burst to some multiple of
number of bytes may be done, but it is important to end the burst
on an exact multiple for best performance.
The best example of this I am aware of are the PPC64 PCI
controllers, where if you end a burst mid-cacheline then
chip has to refetch the data and the IOMMU translations
which hurts performance a lot.
3) Burst on a single byte count multiple. Bursts shall end
exactly on the next multiple boundary for best performance.
Sparc64 and Alpha's PCI controllers operate this way. They
disconnect any device which tries to burst across a cacheline
boundary.
Actually, newer sparc64 PCI controllers do not have this behavior.
That is why the "pdev" is passed into the interface, so I can
add code later to check which PCI controller the system is using
and give advice accordingly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I believe at least for seccomp it's worth to turn off the tsc, not just for
HT but for the L2 cache too. So it's up to you, either you turn it off
completely (which isn't very nice IMHO) or I recommend to apply this below
patch.
This has been tested successfully on x86-64 against current cogito
repository (i686 compiles so I didn't bother testing ;). People selling
the cpu through cpushare may appreciate this bit for a peace of mind.
There's no way to get any timing info anymore with this applied
(gettimeofday is forbidden of course). The seccomp environment is
completely deterministic so it can't be allowed to get timing info, it has
to be deterministic so in the future I can enable a computing mode that
does a parallel computing for each task with server side transparent
checkpointing and verification that the output is the same from all the 2/3
seller computers for each task, without the buyer even noticing (for now
the verification is left to the buyer client side and there's no
checkpointing, since that would require more kernel changes to track the
dirty bits but it'll be easy to extend once the basic mode is finished).
Eliminating a cold-cache read of the cr4 global variable will save one
cacheline during the tlb flush while making the code per-cpu-safe at the
same time. Thanks to Mikael Pettersson for noticing the tlb flush wasn't
per-cpu-safe.
The global tlb flush can run from irq (IPI calling do_flush_tlb_all) but
it'll be transparent to the switch_to code since the IPI won't make any
change to the cr4 contents from the point of view of the interrupted code
and since it's now all per-cpu stuff, it will not race. So no need to
disable irqs in switch_to slow path.
Signed-off-by: Andrea Arcangeli <andrea@cpushare.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the CFQ io scheduler to the new time sliced design (cfq
v3). It provides full process fairness, while giving excellent
aggregate system throughput even for many competing processes. It
supports io priorities, either inherited from the cpu nice value or set
directly with the ioprio_get/set syscalls. The latter closely mimic
set/getpriority.
This import is based on my latest from -mm.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch exports kexec global variable "crash_notes" to user space
through sysfs as kernel attribute in /sys/kernel.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the x86_64 implementation of machine kexec. 32bit compatibility
support has been implemented, and machine_kexec has been enhanced to not care
about the changing internal kernel paget table structures.
From: Alexander Nyberg <alexn@dsv.su.se>
build fix
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For one kernel to report a crash another kernel has created we need
to have 2 kernels loaded simultaneously in memory. To accomplish this
the two kernels need to built to run at different physical addresses.
This patch adds the CONFIG_PHYSICAL_START option to the x86_64 kernel
so we can do just that. You need to know what you are doing and
the ramifications are before changing this value, and most users
won't care so I have made it depend on CONFIG_EMBEDDED
bzImage kernels will work and run at a different address when compiled
with this option but they will still load at 1MB. If you need a kernel
loaded at a different address as well you need to boot a vmlinux.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When coming out of apic mode attempt to set the appropriate
apic back into virtual wire mode. This improves on previous versions
of this patch by by never setting bot the local apic and the ioapic
into veritual wire mode.
This code looks at data from the mptable to see if an ioapic has
an ExtInt input to make this decision. A future improvement
is to figure out which apic or ioapic was in virtual wire mode
at boot time and to remember it. That is potentially a more accurate
method, of selecting which apic to place in virutal wire mode.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Maciej W. Rozycki" <macro@linux-mips.org>
Rename APIC_MODE_EXINT to APIC_MODE_EXTINT - I think it should be named
after what the mode is called in documentation.
From: "Eric W. Biederman" <ebiederm@lnxi.com>
I have reduced this patch to just the name change in the header. And
integrated the changes into the patches that add those
lines. Otherwise I ran into some ugly dependencies.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do some basic initial tuning.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reimplement the balance on exec balancing to be sched-domains aware. Use this
to also do balance on fork balancing. Make x86_64 do balance on fork over the
NUMA domain.
The problem that the non sched domains aware blancing became apparent on dual
core, multi socket opterons. What we want is for the new tasks to be sent to
a different socket, but more often than not, we would first load up our
sibling core, or fill two cores of a single remote socket before selecting a
new one.
This gives large improvements to STREAM on such systems.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the very aggressive idle stuff that has recently gone into 2.6 - it is
going against the direction we are trying to go. Hopefully we can regain
performance through other methods.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do CPU load averaging over a number of different intervals. Allow each
interval to be chosen by sending a parameter to source_load and target_load.
0 is instantaneous, idx > 0 returns a decaying average with the most recent
sample weighted at 2^(idx-1). To a maximum of 3 (could be easily increased).
So generally a higher number will result in more conservative balancing.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.12-rc6-mm1 has a few remaining synchronize_kernel()s, some (but not
all) in comments. This patch changes these synchronize_kernel() calls (and
comments) to synchronize_rcu() or synchronize_sched() as follows:
- arch/x86_64/kernel/mce.c mce_read(): change to synchronize_sched() to
handle races with machine-check exceptions (synchronize_rcu() would not cut
it given RCU implementations intended for hardcore realtime use.
- drivers/input/serio/i8042.c i8042_stop(): change to synchronize_sched() to
handle races with i8042_interrupt() interrupt handler. Again,
synchronize_rcu() would not cut it given RCU implementations intended for
hardcore realtime use.
- include/*/kdebug.h comments: change to synchronize_sched() to handle races
with NMIs. As before, synchronize_rcu() would not cut it...
- include/linux/list.h comment: change to synchronize_rcu(), since this
comment is for list_del_rcu().
- security/keys/key.c unregister_key_type(): change to synchronize_rcu(),
since this is interacting with RCU read side.
- security/keys/process_keys.c install_session_keyring(): change to
synchronize_rcu(), since this is interacting with RCU read side.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes register saving so that each register is only saved once,
and adds missing saving of %cr8 on x86-64. Some reordering so that
save/restore is more logical/safer (segment registers should be restored
after gdt).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Broadcast IPI's provide un-expected behaviour for cpu hotplug. CPU's in
offline state also end up receiving the IPI. Once the cpus become online they
receive these stale IPI's which are bad and introduce unexpected behaviour.
This is easily avoided by not sending a broadcast and addressing just the
CPU's in online map. Doing prelim cycle counts it appears there is no big
overhead and numbers seem around 0x3000-0x3900 on an average on x86 and x86_64
systems with CPUS running 3G, both for broadcast and mask version of the
API's.
The shortcuts are useful only for flat mode (where the perf shows no
degradation), and in cluster mode, its unicast anyway. Its simpler to just
not use broadcast anymore.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Experimental CPU hotplug patch for x86_64
-----------------------------------------
This supports logical CPU online and offline.
- Test with maxcpus=1, and then kick other cpu's off to test if init code
is all cleaned up. CONFIG_SCHED_SMT works as well.
- idle threads are forked on demand from keventd threads for clean startup
TBD:
1. Not tested on a real NUMA machine (tested with numa=fake=2)
2. Handle ACPI pieces for physical hotplug support.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Shaohua.li<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is based on work by Carlos O'Donell and Matthew Wilcox. It
introduces/updates the compat_time_t type and uses it for compat siginfo
structures. I have built this on ppc64 and x86_64.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix (in the architectures I'm actually building for) the UP definition of
per_cpu so that the cpu specified may be any expression, not just an
identifier or a suffix expression.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch adds the x86_64 architecture specific implementation
for function return probes.
Function return probes is a mechanism built on top of kprobes that allows
a caller to register a handler to be called when a given function exits.
For example, to instrument the return path of sys_mkdir:
static int sys_mkdir_exit(struct kretprobe_instance *i, struct pt_regs *regs)
{
printk("sys_mkdir exited\n");
return 0;
}
static struct kretprobe return_probe = {
.handler = sys_mkdir_exit,
};
<inside setup function>
return_probe.kp.addr = (kprobe_opcode_t *) kallsyms_lookup_name("sys_mkdir");
if (register_kretprobe(&return_probe)) {
printk(KERN_DEBUG "Unable to register return probe!\n");
/* do error path */
}
<inside cleanup function>
unregister_kretprobe(&return_probe);
The way this works is that:
* At system initialization time, kernel/kprobes.c installs a kprobe
on a function called kretprobe_trampoline() that is implemented in
the arch/x86_64/kernel/kprobes.c (More on this later)
* When a return probe is registered using register_kretprobe(),
kernel/kprobes.c will install a kprobe on the first instruction of the
targeted function with the pre handler set to arch_prepare_kretprobe()
which is implemented in arch/x86_64/kernel/kprobes.c.
* arch_prepare_kretprobe() will prepare a kretprobe instance that stores:
- nodes for hanging this instance in an empty or free list
- a pointer to the return probe
- the original return address
- a pointer to the stack address
With all this stowed away, arch_prepare_kretprobe() then sets the return
address for the targeted function to a special trampoline function called
kretprobe_trampoline() implemented in arch/x86_64/kernel/kprobes.c
* The kprobe completes as normal, with control passing back to the target
function that executes as normal, and eventually returns to our trampoline
function.
* Since a kprobe was installed on kretprobe_trampoline() during system
initialization, control passes back to kprobes via the architecture
specific function trampoline_probe_handler() which will lookup the
instance in an hlist maintained by kernel/kprobes.c, and then call
the handler function.
* When trampoline_probe_handler() is done, the kprobes infrastructure
single steps the original instruction (in this case just a top), and
then calls trampoline_post_handler(). trampoline_post_handler() then
looks up the instance again, puts the instance back on the free list,
and then makes a long jump back to the original return instruction.
So to recap, to instrument the exit path of a function this implementation
will cause four interruptions:
- A breakpoint at the very beginning of the function allowing us to
switch out the return address
- A single step interruption to execute the original instruction that
we replaced with the break instruction (normal kprobe flow)
- A breakpoint in the trampoline function where our instrumented function
returned to
- A single step interruption to execute the original instruction that
we replaced with the break instruction (normal kprobe flow)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The preempt_count member of struct thread_info is currently either defined
as int, unsigned int or __s32 depending on arch. This patch makes the type
of preempt_count an int on all archs.
Having preempt_count be an unsigned type prevents the catching of
preempt_count < 0 bugs, and using int on some archs and __s32 on others is
not exactely "neat" - much nicer when it's just int all over.
A previous version of this patch was already ACK'ed by Robert Love, and the
only change in this version of the patch compared to the one he ACK'ed is
that this one also makes sure the preempt_count member is consistently
commented.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add 2 macros to set and get debugreg on x86_64. This is useful for Xen
because it will need only to redefine each macro to a hypervisor call.
Signed-off-by: Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk>
Cc: Ian Pratt <m+Ian.Pratt@cl.cam.ac.uk>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename user_mode to user_mode_vm and add a user_mode macro similar to the
x86-64 one.
This is useful for Xen because the linux xen kernel does not runs on the same
priviledge that a vanilla linux kernel, and with this we just need to redefine
user_mode().
Signed-off-by: Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk>
Cc: Ian Pratt <m+Ian.Pratt@cl.cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the timer frequency selectable. The timer interrupt may cause bus
and memory contention in large NUMA systems since the interrupt occurs
on each processor HZ times per second.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define pcibus_to_node to be able to figure out which NUMA node contains a
given PCI device. This defines pcibus_to_node(bus) in
include/linux/topology.h and adjusts the macros for i386 and x86_64 that
already provided a way to determine the cpumask of a pci device.
x86_64 was changed to not build an array of cpumasks anymore. Instead an
array of nodes is build which can be used to generate the cpumask via
node_to_cpumask.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Issue:
Current tsc based delay_calibration can result in significant errors in
loops_per_jiffy count when the platform events like SMIs
(System Management Interrupts that are non-maskable) are present. This could
lead to potential kernel panic(). This issue is becoming more visible with 2.6
kernel (as default HZ is 1000) and on platforms with higher SMI handling
latencies. During the boot time, SMIs are mostly used by BIOS (for things
like legacy keyboard emulation).
Description:
The psuedocode for current delay calibration with tsc based delay looks like
(0) Estimate a value for loops_per_jiffy
(1) While (loops_per_jiffy estimate is accurate enough)
(2) wait for jiffy transition (jiffy1)
(3) Note down current tsc (tsc1)
(4) loop until tsc becomes tsc1 + loops_per_jiffy
(5) check whether jiffy changed since jiffy1 or not and refine
loops_per_jiffy estimate
Consider the following cases
Case 1:
If SMIs happen between (2) and (3) above, we can end up with a
loops_per_jiffy value that is too low. This results in shorted delays and
kernel can panic () during boot (Mostly at IOAPIC timer initialization
timer_irq_works() as we don't have enough timer interrupts in a specified
interval).
Case 2:
If SMIs happen between (3) and (4) above, then we can end up with a
loops_per_jiffy value that is too high. And with current i386 code, too
high lpj value (greater than 17M) can result in a overflow in
delay.c:__const_udelay() again resulting in shorter delay and panic().
Solution:
The patch below makes the calibration routine aware of asynchronous events
like SMIs. We increase the delay calibration time and also identify any
significant errors (greater than 12.5%) in the calibration and notify it to
user.
Patch below changes both i386 and x86-64 architectures to use this
new and improved calibrate_delay_direct() routine.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds in the necessary support for sparsemem such that x86-64
kernels may use sparsemem as an alternative to discontigmem for NUMA
kernels. Note that this does no preclude one from continuing to build NUMA
kernels using discontigmem, but merely allows the option to build NUMA
kernels with sparsemem.
Interestingly, the use of sparsemem in lieu of discontigmem in NUMA kernels
results in reduced text size for otherwise equivalent kernels as shown in
the example builds below:
text data bss dec hex filename
2371036 765884 1237108 4374028 42be0c vmlinux.discontig
2366549 776484 1302772 4445805 43d66d vmlinux.sparse
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to use the alternative sparsemem implmentation for NUMA kernels,
we need to reorganize the config options. This patch effectively abstracts
out the CONFIG_DISCONTIGMEM options to CONFIG_NUMA in most cases. Thus,
the discontigmem implementation may be employed as always, but the
sparsemem implementation may be used alternatively.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch effectively eliminates direct use of pgdat->node_mem_map outside
of the DISCONTIG code. On a flat memory system, these fields aren't
currently used, neither are they on a sparsemem system.
There was also a node_mem_map(nid) macro on many architectures. Its use
along with the use of ->node_mem_map itself was not consistent. It has
been removed in favor of two new, more explicit, arch-independent macros:
pgdat_page_nr(pgdat, pagenr)
nid_page_nr(nid, pagenr)
I called them "pgdat" and "nid" because we overload the term "node" to mean
"NUMA node", "DISCONTIG node" or "pg_data_t" in very confusing ways. I
believe the newer names are much clearer.
These macros can be overridden in the sparsemem case with a theoretically
slower operation using node_start_pfn and pfn_to_page(), instead. We could
make this the only behavior if people want, but I don't want to change too
much at once. One thing at a time.
This patch removes more code than it adds.
Compile tested on alpha, alpha discontig, arm, arm-discontig, i386, i386
generic, NUMAQ, Summit, ppc64, ppc64 discontig, and x86_64. Full list
here: http://sr71.net/patches/2.6.12/2.6.12-rc1-mhp2/configs/
Boot tested on NUMAQ, x86 SMP and ppc64 power4/5 LPARs.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin J. Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of the code in arch/*/mm/hugetlbpage.c is quite similar. This patch
attempts to consolidate a lot of the code across the arch's, putting the
combined version in mm/hugetlb.c. There are a couple of uglyish hacks in
order to covert all the hugepage archs, but the result is a very large
reduction in the total amount of code. It also means things like hugepage
lazy allocation could be implemented in one place, instead of six.
Tested, at least a little, on ppc64, i386 and x86_64.
Notes:
- this patch changes the meaning of set_huge_pte() to be more
analagous to set_pte()
- does SH4 need s special huge_ptep_get_and_clear()??
Acked-by: William Lee Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements a number of smp_processor_id() cleanup ideas that
Arjan van de Ven and I came up with.
The previous __smp_processor_id/_smp_processor_id/smp_processor_id API
spaghetti was hard to follow both on the implementational and on the
usage side.
Some of the complexity arose from picking wrong names, some of the
complexity comes from the fact that not all architectures defined
__smp_processor_id.
In the new code, there are two externally visible symbols:
- smp_processor_id(): debug variant.
- raw_smp_processor_id(): nondebug variant. Replaces all existing
uses of _smp_processor_id() and __smp_processor_id(). Defined
by every SMP architecture in include/asm-*/smp.h.
There is one new internal symbol, dependent on DEBUG_PREEMPT:
- debug_smp_processor_id(): internal debug variant, mapped to
smp_processor_id().
Also, i moved debug_smp_processor_id() from lib/kernel_lock.c into a new
lib/smp_processor_id.c file. All related comments got updated and/or
clarified.
I have build/boot tested the following 8 .config combinations on x86:
{SMP,UP} x {PREEMPT,!PREEMPT} x {DEBUG_PREEMPT,!DEBUG_PREEMPT}
I have also build/boot tested x64 on UP/PREEMPT/DEBUG_PREEMPT. (Other
architectures are untested, but should work just fine.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Appended patch will setup compatibility mode TASK_SIZE properly. This will
fix atleast three known bugs that can be encountered while running
compatibility mode apps.
a) A malicious 32bit app can have an elf section at 0xffffe000. During
exec of this app, we will have a memory leak as insert_vm_struct() is
not checking for return value in syscall32_setup_pages() and thus not
freeing the vma allocated for the vsyscall page. And instead of exec
failing (as it has addresses > TASK_SIZE), we were allowing it to
succeed previously.
b) With a 32bit app, hugetlb_get_unmapped_area/arch_get_unmapped_area
may return addresses beyond 32bits, ultimately causing corruption
because of wrap-around and resulting in SEGFAULT, instead of returning
ENOMEM.
c) 32bit app doing this below mmap will now fail.
mmap((void *)(0xFFFFE000UL), 0x10000UL, PROT_READ|PROT_WRITE,
MAP_FIXED|MAP_PRIVATE|MAP_ANON, 0, 0);
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When Linux is running on the Xen virtual machine monitor, physical
addresses are virtualised and cannot be directly referenced by the AGP
GART. This patch fixes the GART driver for Xen by adding a layer of
abstraction between physical addresses and 'GART addresses'.
Architecture-specific functions are also defined for allocating and freeing
the GATT. Xen requires this to ensure that table really is contiguous from
the point of view of the GART.
These extra interface functions are defined as 'no-ops' for all existing
architectures that use the GART driver.
Signed-off-by: Keir Fraser <keir@xensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
These days <linux/ioctl32.h> handles everything, no need for an asm
header on just two architectures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Collected NMI watchdog fixes.
- Fix call of check_nmi_watchdog
- Remove earlier move of check_nmi_watchdog to later. It does not fix the
race it was supposed to fix fully.
- Remove unused P6 definitions
- Add support for performance counter based watchdog on P4 systems.
This allows to run it only once per second, which saves some CPU time.
Previously it would run at 1000Hz, which was too much.
Code ported from i386
Make this the default on Intel systems.
- Use check_nmi_watchdog with local APIC based nmi
- Fix race in touch_nmi_watchdog
- Fix bug that caused incorrect performance counters to be programmed in a
few cases on K8.
- Remove useless check for local APIC
- Use local_t and per_cpu variables for per CPU data.
- Keep other CPUs busy during check_nmi_watchdog to make sure they really
tick when in lapic mode.
- Only check CPUs that are actually online.
- Various other fixes.
- Fix fallback path when MSRs are unimplemented
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are unfortunately more and more multi processor Opteron systems which
don't have HPET timer support in the southbridge. This covers in particular
Nvidia and VIA chipsets. They also don't guarantee that the TSCs are
synchronized between CPUs; and especially with MP powernow the systems are
nearly unusable because the time gets very inconsistent between CPUs.
The timer code for x86-64 was originally written under the assumption that we
could fall back to the HPET timer on such systems. But this doesn't work
there.
Another alternative is to use the ACPI PM timer as primary time source. This
patch does that. The kernel only uses PM timer when there is no other choice
because it has some disadvantages.
Ported over from i386. It should be faster than the i386 version because I
dropped the "read three times" workaround, but is still considerable slower
than HPET and also does not work together with vsyscalls which have to be
disabled.
Cc: <mark.langsdorf@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is unnecessary on modern Intel or AMD systems, and that is all we support
on x86-64
Also causes problems on various systems
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Needed by big systems and only costs a few K of memory.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This works around a bug in the AMD K8 CPUs.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes some needlessly global identifiers static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Arjan van de Ven <arjanv@infradead.org>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New file - asm-generic/signal.h. Contains declarations of
__sighandler_t, __sigrestore_t, SIG_DFL, SIG_IGN, SIG_ERR and default
definitions of SIG_BLOCK, SIG_UNBLOCK and SIG_SETMASK.
asm-*/signal.h switched to including it. The only exception is
asm-parisc/signal.h that wants its own declaration of __sighandler_t;
that one is left as-is.
asm-ppc64/signal.h required one more thing - unlike everybody else it
used __sigrestorer_t instead of usual __sigrestore_t. PPC64 switched to
common spelling.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Discussing with Matthew Wilcox some of his outstanding patches lead me to
this patch (among others).
The preamble in struct sigevent can be expressed independently of the
architecture.
Also use __ARCH_SI_PREAMBLE_SIZE on ia64.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch moves the IRQ-related SA_xxx flags (namely, SA_PROBE,
SA_SAMPLE_RANDOM and SA_SHIRQ) from all the arch-specific headers to
linux/signal.h. This looks like a left-over after the irq-handling code
was consolidated. The code was moved to kernel/irq/*, but the flags are
still left per-arch.
Right now, adding a new IRQ flag to the arch-specific header, like this
patch does:
http://cvs.sourceforge.net/viewcvs.py/*checkout*/alsa/alsa-driver/utils/patches/pcsp-kernel-2.6.10-03.diff?rev=1.1
no longer works, it breaks the compilation for all other arches, unless you
add that flag to all the other arch-specific headers too. So I think such
a clean-up makes sense.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch eliminates all kernel BUGs, trims about 35k off the typical
kernel, and makes the system slightly faster.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The specifications that talk about E820 map doesn't have an upper limit on
the number of e820 entries. But, today's kernel has a hard limit of 32.
With increase in memory size, we are seeing the number of E820 entries
reaching close to 32. Patch below bumps the number upto 128.
The patch changes the location of EDDBUF in zero-page (as it comes after E820).
As, EDDBUF is not used by boot loaders, this patch should not have any effect
on bootloader-setup code interface.
Patch covers both i386 and x86-64.
Tested on:
* grub booting bzImage
* lilo booting bzImage with EDID info enabled
* pxeboot of bzImage
Side-effect:
bss increases by ~ 2K and init.data increases by ~7.5K
on all systems, due to increase in size of static arrays.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent support for K8 multicore was misported from x86-64 to i386, due
to an unnecessary inconsistency between the CPUID code. Sure, there is are
no x86-64 VIA chips yet, but it should happen eventually.
This patch fixes the i386 bug as well as makes x86-64 match i386 in the
handing of the CPUID array.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bug against an xSeries system showed up recently noting that the
check_nmi_watchdog() test was failing.
I have been investigating it and discovered in both i386 and x86_64 the
recent change to the routine to use the cpu_callin_map has uncovered a
problem. Prior to that change, on an SMP box, the test was trivally
passing because all cpu's were found to not yet be online, but now with the
callin_map they are discovered, it goes on to test the counter and they
have not yet begun to increment, so it announces a CPU is stuck and bails
out.
On all the systems I have access to test, the announcement of failure is
also bougs... by the time you can login and check /proc/interrupts, the
NMI count is happily incrementing on all CPUs. Its just that the test is
being done too early.
I have tried moving the call to the test around a bit, and it was always
too early. I finally hit on this proposed solution, it delays the routine
via a late_initcall(), seems like the right solution to me.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace misleading definition of FIRST_USER_PGD_NR 0 by definition of
FIRST_USER_ADDRESS 0 in all the MMU architectures beyond arm and arm26.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This will allow hotplug CPU in the future and in general cleans up a lot of
crufty code. It also should plug some races that the old hackish way
introduces. Remove one old race workaround in NMI watchdog setup that is not
needed anymore.
I removed the old total sum of bogomips reporting code. The brag value of
BogoMips has been greatly devalued in the last years on the open market.
Real CPU hotplug will need some more work, but the infrastructure for it is
there now.
One drawback: the new TSC sync algorithm is less accurate than before. The
old way of zeroing TSCs is too intrusive to do later. Instead the TSC of the
BP is duplicated now, which is less accurate.
akpm:
- sync_tsc_bp_init seems to have the sense of `init' inverted.
- SPIN_LOCK_UNLOCKED is deprecated - use DEFINE_SPINLOCK.
Cc: <rusty@rustcorp.com.au>
Cc: <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was confusingly named.
Signed-off-by: Andi Kleen <ak@suse.de>
DESC
x86_64: Switch SMP bootup over to new CPU hotplug state machine
EDESC
From: "Andi Kleen" <ak@suse.de>
This will allow hotplug CPU in the future and in general cleans up a lot of
crufty code. It also should plug some races that the old hackish way
introduces. Remove one old race workaround in NMI watchdog setup that is not
needed anymore.
I removed the old total sum of bogomips reporting code. The brag value of
BogoMips has been greatly devalued in the last years on the open market.
Real CPU hotplug will need some more work, but the infrastructure for it is
there now.
One drawback: the new TSC sync algorithm is less accurate than before. The
old way of zeroing TSCs is too intrusive to do later. Instead the TSC of the
BP is duplicated now, which is less accurate.
Cc: <rusty@rustcorp.com.au>
Cc: <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Appended patch adds the support for Intel dual-core detection and displaying
the core related information in /proc/cpuinfo.
It adds two new fields "core id" and "cpu cores" to x86 /proc/cpuinfo and the
"core id" field for x86_64("cpu cores" field is already present in x86_64).
Number of processor cores in a die is detected using cpuid(4) and this is
documented in IA-32 Intel Architecture Software Developer's Manual (vol 2a)
(http://developer.intel.com/design/pentium4/manuals/index_new.htm#sdm_vol2a)
This patch also adds cpu_core_map similar to cpu_sibling_map.
Slightly hacked by AK.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Calling a notifier three times in the debug handler does not make much sense,
because a debugger can figure out the various conditions by itself. Remove
the additional calls to DIE_DEBUG and DIE_DEBUGSTEP completely.
This matches what i386 does now.
This also makes sure interrupts are always still disabled when calling a
debugger, which prevents:
BUG: using smp_processor_id() in preemptible [00000001] code: tpopf/1470
caller is post_kprobe_handler+0x9/0x70
Call Trace:<ffffffff8024f10f>{smp_processor_id+191} <ffffffff80120e69>{post_kpro
be_handler+9}
<ffffffff80120f7a>{kprobe_exceptions_notify+58}
<ffffffff80144fc0>{notifier_call_chain+32} <ffffffff80110daf>{do_debug+335}
<ffffffff8010f513>{debug+127} <EOE>
on preemptible debug kernels with kprobes when single stepping in user space.
This was probably a bug even on non preempt kernels, this function was
supposed to be running with interrupts off according to a comment there.
Note to third part debugger maintainers: please double check your debugger can
still single step.
Cc: <prasanna@in.ibm.com>
Cc: <jbeulich@novell.com>
Cc: <kaos@sgi.com>
Cc: <jim.houston@ccur.com>
Cc: <jfv@bluesong.net>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Look for gaps in the e820 memory map to put PCI resources in.
This hopefully fixes problems with the PCI code assigning 32bit BARs MMIO
resources which are >32bit.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
local_t is actually a win over atomic_t because it does not need lock
prefixes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Intel Noconas the TSC ticks with a constant frequency. Don't scale the
factor used by udelay when cpufreq changes the frequency.
This generalizes an earlier patch by Intel for this.
Cc: <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use a real VMA to map the 32bit vsyscall page
This interacts better with Hugh's upcomming VMA walk optimization
Also removes some ugly special cases.
Code roughly modelled after the ppc64 vdso version from Ben Herrenschmidt.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the correct file name in BUG()
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
