There are some vestiges of old code that was used for bypassing the stripe
cache on reads in raid5.c. This was never updated after the change from
buffer_heads to bios, but was left as a reminder.
That functionality has nowe been implemented in a completely different way, so
the old code can go.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
stripe_to_pdidx finds the index of the parity disk for a given stripe. It
assumes raid5 in that it uses "disks-1" to determine the number of data disks.
This is incorrect for raid6 but fortunately the two usages cancel each other
out. The only way that 'data_disks' affects the calculation of pd_idx in
raid5_compute_sector is when it is divided into the sector number. But as
that sector number is calculated by multiplying in the wrong value of
'data_disks' the division produces the right value.
So it is innocuous but needs to be fixed.
Also change the calculation of raid_disks in compute_blocknr to make it
more obviously correct (it seems at first to always use disks-1 too).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call the chunk_aligned_read where appropriate.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a bypass-the-cache read fails, we simply try again through the cache. If
it fails again it will trigger normal recovery precedures.
update 1:
From: NeilBrown <neilb@suse.de>
1/
chunk_aligned_read and retry_aligned_read assume that
data_disks == raid_disks - 1
which is not true for raid6.
So when an aligned read request bypasses the cache, we can get the wrong data.
2/ The cloned bio is being used-after-free in raid5_align_endio
(to test BIO_UPTODATE).
3/ We forgot to add rdev->data_offset when submitting
a bio for aligned-read
4/ clone_bio calls blk_recount_segments and then we change bi_bdev,
so we need to invalidate the segment counts.
5/ We don't de-reference the rdev when the read completes.
This means we need to record the rdev to so it is still
available in the end_io routine. Fortunately
bi_next in the original bio is unused at this point so
we can stuff it in there.
6/ We leak a cloned bio if the target rdev is not usable.
From: NeilBrown <neilb@suse.de>
update 2:
1/ When aligned requests fail (read error) they need to be retried
via the normal method (stripe cache). As we cannot be sure that
we can process a single read in one go (we may not be able to
allocate all the stripes needed) we store a bio-being-retried
and a list of bioes-that-still-need-to-be-retried.
When find a bio that needs to be retried, we should add it to
the list, not to single-bio...
2/ We were never incrementing 'scnt' when resubmitting failed
aligned requests.
[akpm@osdl.org: build fix]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This will encourage read request to be on only one device, so we will often be
able to bypass the cache for read requests.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I forgot to has the size-in-blocks to (loff_t) before shifting up to a
size-in-bytes.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This changes two if() BUG(); usages to BUG_ON(); so people
can disable it safely.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This is very different from other raid levels and all requests go through a
'stripe cache', and it has congestion management already.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The error handling routines don't use proper locking, and so two concurrent
errors could trigger a problem.
So:
- use test-and-set and test-and-clear to synchonise
the In_sync bits with the ->degraded count
- use the spinlock to protect updates to the
degraded count (could use an atomic_t but that
would be a bigger change in code, and isn't
really justified)
- remove un-necessary locking in raid5
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They are not needed. conf->failed_disks is the same as mddev->degraded and
conf->working_disks is conf->raid_disks - mddev->degraded.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
Some device state has changed requiring superblock update
on all devices.
MD_CHANGE_CLEAN
The array has transitions from 'clean' to 'dirty' or back,
requiring a superblock update on active devices, but possibly
not on spares
MD_CHANGE_PENDING
A superblock update is underway.
We wait for an update to complete by waiting for all flags to be clear. A
flag can be set at any time, even during an update, without risk that the
change will be lost.
Stop exporting md_update_sb - isn't needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.
[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment gives more details, but I didn't quite have the sequencing write,
so there was room for races to leave bits unset in the on-disk bitmap for
short periods of time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a device is unplugged, requests are moved from one or two (depending on
whether a bitmap is in use) queues to the main request queue.
So whenever requests are put on either of those queues, we should make sure
the raid5 array is 'plugged'. However we don't. We currently plug the raid5
queue just before putting requests on queues, so there is room for a race. If
something unplugs the queue at just the wrong time, requests will be left on
the queue and nothing will want to unplug them. Normally something else will
plug and unplug the queue fairly soon, but there is a risk that nothing will.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array is started we start one or two threads (two if there is a
reshape or recovery that needs to be completed).
We currently start these *before* the array is completely set up and in
particular before queue->queuedata is set. If the thread actually starts
very quickly on another CPU, we can end up dereferencing queue->queuedata
and oops.
This patch also makes sure we don't try to start a recovery if a reshape is
being restarted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have reports of a problem with raid5 which turns out to be because the raid5
device gets stuck in a 'plugged' state. This shouldn't be able to happen as
3msec after it gets plugged it should get unplugged. However it happens
none-the-less. This patch fixes the problem and is a reasonable thing to do,
though it might hurt performance slightly in some cases.
Until I can find the real problem, we should probably have this workaround in
place.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As data_disks is *less* than raid_disks, the current test here is obviously
wrong. And as the difference is already available in conf->max_degraded, it
makes much more sense to use that.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... as raid5 sync_request is WAY too big.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For a while we have had checkpointing of resync. The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.
Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a lot of commonality between raid5.c and raid6main.c. This patches
merges both into one module called raid456. This saves a lot of code, and
paves the way for online raid5->raid6 migrations.
There is still duplication, e.g. between handle_stripe5 and handle_stripe6.
This will probably be cleaned up later.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The largest chunk size the code can support without substantial surgery is
2^30 bytes, so make that the limit instead of an arbitrary 4Meg. Some day,
the 'chunksize' should change to a sector-shift instead of a byte-count. Then
no limit would be needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
raid5 overloads bi_phys_segments to count the number of blocks that the
request was broken in to so that it knows when the bio is completely handled.
Accessing this must always be done under a spinlock. In one case we also call
bi_end_io under that spinlock, which probably isn't ideal as bi_end_io could
be expensive (even though it isn't allowed to sleep).
So we reducde the range of the spinlock to just accessing bi_phys_segments.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
wait_event_lock_irq puts a ';' after its usage of the 4th arg, so we don't
need to.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows user-space to access data safely. This is needed for raid5
reshape as user-space needs to take a backup of the first few stripes before
allowing reshape to commence.
It will also be useful in cluster-aware raid1 configurations so that all
cluster members can leave a section of the array untouched while a
resync/recovery happens.
A 'start' and 'end' of the suspended range are written to 2 sysfs attributes.
Note that only one range can be suspended at a time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check_reshape checks validity and does things that can be done instantly -
like adding devices to raid1. start_reshape initiates a restriping process to
convert the whole array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of checkpointing at each stripe, only checkpoint when a new write
would overwrite uncheckpointed data. Block any write to the uncheckpointed
area. Arbitrarily checkpoint at least every 3Meg.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We allow the superblock to record an 'old' and a 'new' geometry, and a
position where any conversion is up to. The geometry allows for changing
chunksize, layout and level as well as number of devices.
When using verion-0.90 superblock, we convert the version to 0.91 while the
conversion is happening so that an old kernel will refuse the assemble the
array. For version-1, we use a feature bit for the same effect.
When starting an array we check for an incomplete reshape and restart the
reshape process if needed. If the reshape stopped at an awkward time (like
when updating the first stripe) we refuse to assemble the array, and let
user-space worry about it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds raid5_reshape and end_reshape which will start and finish the
reshape processes.
raid5_reshape is only enabled in CONFIG_MD_RAID5_RESHAPE is set, to discourage
accidental use.
Read the 'help' for the CONFIG_MD_RAID5_RESHAPE entry.
and Make sure that you have backups, just in case.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides the core of the resize/expand process.
sync_request notices if a 'reshape' is happening and acts accordingly.
It allocated new stripe_heads for the next chunk-wide-stripe in the target
geometry, marking them STRIPE_EXPANDING.
Then it finds which stripe heads in the old geometry can provide data needed
by these and marks them STRIPE_EXPAND_SOURCE. This causes stripe_handle to
read all blocks on those stripes.
Once all blocks on a STRIPE_EXPAND_SOURCE stripe_head are read, any that are
needed are copied into the corresponding STRIPE_EXPANDING stripe_head. Once a
STRIPE_EXPANDING stripe_head is full, it is marks STRIPE_EXPAND_READY and then
is written out and released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to allow that different stripes are of different effective sizes, and
use the appropriate size. Also, when a stripe is being expanded, we must
block any IO attempts until the stripe is stable again.
Key elements in this change are:
- each stripe_head gets a 'disk' field which is part of the key,
thus there can sometimes be two stripe heads of the same area of
the array, but covering different numbers of devices. One of these
will be marked STRIPE_EXPANDING and so won't accept new requests.
- conf->expand_progress tracks how the expansion is progressing and
is used to determine whether the target part of the array has been
expanded yet or not.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before a RAID-5 can be expanded, we need to be able to expand the stripe-cache
data structure.
This requires allocating new stripes in a new kmem_cache. If this succeeds,
we copy cache pages over and release the old stripes and kmem_cache.
We then allocate new pages. If that fails, we leave the stripe cache at it's
new size. It isn't worth the effort to shrink it back again.
Unfortuanately this means we need two kmem_cache names as we, for a short
period of time, we have two kmem_caches. So they are raid5/%s and
raid5/%s-alt
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remainder of this batch implements raid5 reshaping. Currently the only
shape change that is supported is added a device, but it is envisioned that
changing the chunksize and layout will also be supported, as well as changing
the level (e.g. 1->5, 5->6).
The reshape process naturally has to move all of the data in the array, and so
should be used with caution. It is believed to work, and some testing does
support this, but wider testing would be great for increasing my confidence.
You will need a version of mdadm newer than 2.3.1 to make use of raid5 growth.
This is because mdadm need to take a copy of a 'critical section' at the
start of the array incase there is a crash at an awkward moment. On restart,
mdadm will restore the critical section and allow reshape to continue.
I hope to release a 2.4-pre by early next week - it still needs a little more
polishing.
This patch:
Previously the array of disk information was included in the raid5 'conf'
structure which was allocated to an appropriate size. This makes it awkward
to change the size of that array. So we split it off into a separate
kmalloced array which will require a little extra indexing, but is much easier
to grow.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- version-1 superblock
+ The default_bitmap_offset is in sectors, not bytes.
+ the 'size' field in the superblock is in sectors, not KB
- raid0_run should return a negative number on error, not '1'
- raid10_read_balance should not return a valid 'disk' number if
->rdev turned out to be NULL
- kmem_cache_destroy doesn't like being passed a NULL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Store this total in superblock (As appropriate), and make it available to
userspace via sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md supports multiple different RAID level, each being implemented by a
'personality' (which is often in a separate module).
These personalities have fairly artificial 'numbers'. The numbers
are use to:
1- provide an index into an array where the various personalities
are recorded
2- identify the module (via an alias) which implements are particular
personality.
Neither of these uses really justify the existence of personality numbers.
The array can be replaced by a linked list which is searched (array lookup
only happens very rarely). Module identification can be done using an alias
based on level rather than 'personality' number.
The current 'raid5' modules support two level (4 and 5) but only one
personality. This slight awkwardness (which was handled in the mapping from
level to personality) can be better handled by allowing raid5 to register 2
personalities.
With this change in place, the core md module does not need to have an
exhaustive list of all possible personalities, so other personalities can be
added independently.
This patch also moves the check for chunksize being non-zero into the ->run
routines for the personalities that need it, rather than having it in core-md.
This has a side effect of allowing 'faulty' and 'linear' not to have a
chunk-size set.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- replace open-coded hash chain with hlist macros
- Fix hash-table size at one page - it is already quite generous, so there
will never be a need to use multiple pages, so no need for __get_free_pages
No functional change.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace multiple kmalloc/memset pairs with kzalloc calls.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Substitute:
page_cache_get -> get_page
page_cache_release -> put_page
PAGE_CACHE_SHIFT -> PAGE_SHIFT
PAGE_CACHE_SIZE -> PAGE_SIZE
PAGE_CACHE_MASK -> PAGE_MASK
__free_page -> put_page
because we aren't using the page cache, we are just using pages.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is this "FIXME" comment with a typo in it!! that been annoying me for
days, so I just had to remove it.
conf->disks[i].rdev should only be accessed if
- we know we hold a reference or
- the mddev->reconfig_sem is down or
- we have a rcu_readlock
handle_stripe was referencing rdev in three places without any of these. For
the first two, get an rcu_readlock. For the last, the same access
(md_sync_acct call) is made a little later after the rdev has been claimed
under and rcu_readlock, if R5_Syncio is set. So just use that access...
However R5_Syncio isn't really needed as the 'syncing' variable contains the
same information. So use that instead.
Issues, comment, and fix are identical in raid5 and raid6.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is important because bitmap_create uses
mddev->resync_max_sectors
and that doesn't have a valid value until after the array
has been initialised (with pers->run()).
[It doesn't make a difference for current personalities that
support bitmaps, but will make a difference for raid10]
This has the added advantage of meaning with can move the thread->timeout
manipulation inside the bitmap.c code instead of sprinkling identical code
throughout all personalities.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
See patch to md.txt for more details
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Resync code:
A test that isn't needed,
a 'compute_block' that makes more sense
elsewhere (And then doesn't need a test),
a couple of BUG_ONs to confirm the change makes sense.
Printks:
A few were missing KERN_*
Also fix a typo in a comment..
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The raid5 stripe cache was recently changed from fixed size (NR_STRIPES) to
variable size (conf->max_nr_stripes). However there are two places that still
use the constant and as a result, reducing the size of the stripe cache can
result in a deadlock.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bitmap_unplug actually writes data (bits) to storage, so we shouldn't be
holding a spinlock...
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1/ I really should be using the __ATTR macros for defining attributes, so
that the .owner field get set properly, otherwise modules can be removed
while sysfs files are open. This also involves some name changes of _show
routines.
2/ Always lock the mddev (against reconfiguration) for all sysfs attribute
access. This easily avoid certain races and is completely consistant with
other interfaces (ioctl and /proc/mdstat both always lock against
reconfiguration).
3/ raid5 attributes must check that the 'conf' structure actually exists
(the array could have been stopped while an attribute file was open).
4/ A missing 'kfree' from when the raid5_conf_t was converted to have a
kobject embedded, and then converted back again.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A sync of raid5 usually ignore blocks which the bitmap says are in-sync. But
a user-request check or repair should not ignore these.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has the advantage of removing the confusion caused by 'rdev_t' and
'mddev_t' both having 'in_sync' fields.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two refinements to the 'attempt-overwrite-on-read-error' mechanism.
1/ If the array is read-only, don't attempt an over-write.
2/ If there are more than max_nr_stripes read errors on a device with
no success, fail the drive. This will make sure a dead
drive will be eventually kicked even when we aren't trying
to rewrite (which would normally kick a dead drive more quickly.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There isn't really a need for raid5 attributes to be an a subdirectory,
so this patch moves them from
/sys/block/mdX/md/raid5/attribute
to
/sys/block/mdX/md/attribute
This suggests that all md personalities should co-operate about
namespace usage, but that shouldn't be a problem.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With this, raid5 can be asked to check parity without repairing it. It also
keeps a count of the number of incorrect parity blocks found (mismatches) and
reports them through sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
/sys/block/mdX/md/raid5/
contains raid5-related attributes.
Currently
stripe_cache_size
is number of entries in stripe cache, and is settable.
stripe_cache_active
is number of active entries, and in only readable.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the behaviour of raid5 when it gets a read error.
Instead of just failing the device, it tried to find out what should have
been there, and writes it over the bad block. For some media-errors, this
has a reasonable chance of fixing the error. If the write succeeds, and a
subsequent read succeeds as well, raid5 decided the address is OK and
conitnues.
Instead of failing a drive on read-error, we attempt to re-write the block,
and then re-read. If that all works, we allow the device to remain in the
array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of having ->read_sectors and ->write_sectors, combine the two
into ->sectors[2] and similar for the other fields. This saves a branch
several places in the io path, since we don't have to care for what the
actual io direction is. On my x86-64 box, that's 200 bytes less text in
just the core (not counting the various drivers).
Signed-off-by: Jens Axboe <axboe@suse.de>
Most awkward part of this is delaying write requests until bitmap updates have
been flushed.
To achieve this, we have a sequence number (seq_flush) which is incremented
each time the raid5 is unplugged.
If the raid thread notices that this has changed, it flushes bitmap changes,
and assigned the value of seq_flush to seq_write.
When a write request arrives, it is given the number from seq_write, and that
write request may not complete until seq_flush is larger than the saved seq
number.
We have a new queue for storing stripes which are waiting for a bitmap flush
and an extra flag for stripes to record if the write was 'degraded' and so
should not clear the a bit in the bitmap.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md does not yet support BIO_RW_BARRIER, so be honest about it and fail
(-EOPNOTSUPP) any such requests.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The default resync_max_sector is set to "mddev->size << 1". If the
raid-personality-module updates mddev->size, it must update
resync_max_sectors too.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without this, and attempt to 'grow' an array will claim to have synced the
extra part without actually having done anything.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before completing a 'write' the md superblock might need to be updated.
This is best done by the md_thread.
The current code schedules this up and queues the write request for later
handling by the md_thread.
However some personalities (Raid5/raid6) will deadlock if the md_thread
tries to submit requests to its own array.
So this patch changes things so the processes submitting the request waits
for the superblock to be written and then submits the request itself.
This fixes a recently-created deadlock in raid5/raid6
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1/ change the return value (which is number-of-sectors synced)
from 'int' to 'sector_t'.
The number of sectors is usually easily small enough to fit
in an int, but if resync needs to abort, it may want to return
the total number of remaining sectors, which could be large.
Also errors cannot be returned as negative numbers now, so use
0 instead
2/ Add a 'skipped' return parameter to allow the array to report
that it skipped the sectors. This allows md to take this into account
in the speed calculations.
Currently there is no important skipping, but the bitmap-based-resync
that is coming will use this.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When md marks the superblock dirty before a write, it calls
generic_make_request (to write the superblock) from within
generic_make_request (to write the first dirty block), which could cause
problems later.
With this patch, the superblock write is always done by the helper thread, and
write request are delayed until that write completes.
Also, the locking around marking the array dirty and writing the superblock is
improved to avoid possible races.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md_enter_safemode checks if it is time to mark the md superblock as 'clean'.
i.e. if all writes have completed and a suitable delay has passed.
This is currently called from md_handle_safemode which in-turn is called
(almost) every time md_check_recovery is called, and from the end of
md_do_sync which causes the mddev->thread to run, which will always call
md_check_recovery as well.
So it doesn't need to be a separate function and fits quite well into
md_check_recovery.
The "almost" is because multipathd calls md_check_recovery but not
md_handle_safemode. This is OK because the code from md_enter_safemode is a
no-op if mddev->safemode == 0, which it always is for a multipathd (providing
we don't allow it to be set to 2 on a signal...)
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We we set the too early, they may still be in place and possibly get called
even though the array didn't get set up properly.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
